This patch enables the SRv6 encapsulation mode to carry an IPv4 payload.
All the infrastructure was already present, I just had to add a parameter
to seg6_do_srh_encap() to specify the inner packet protocol, and perform
some additional checks.
Usage example:
ip route add 1.2.3.4 encap seg6 mode encap segs fc00::1,fc00::2 dev eth0
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forwarding or sending out an ICMPv6 error, look at the embedded
packet that triggered the error and compute a flow hash over its
headers.
This let's us route the ICMP error together with the flow it belongs to
when multipath (ECMP) routing is in use, which in turn makes Path MTU
Discovery work in ECMP load-balanced or anycast setups (RFC 7690).
Granted, end-hosts behind the ECMP router (aka servers) need to reflect
the IPv6 Flow Label for PMTUD to work.
The code is organized to be in parallel with ipv4 stack:
ip_multipath_l3_keys -> ip6_multipath_l3_keys
fib_multipath_hash -> rt6_multipath_hash
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for functions that fill out the IPv6 flow info to also pass a hash
computed over the skb contents. The hash value will drive the multipath
routing decisions.
This is intended for special treatment of ICMPv6 errors, where we would
like to make a routing decision based on the flow identifying the
offending IPv6 datagram that triggered the error, rather than the flow
of the ICMP error itself.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One too many arguments compared to the non-stub version.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ffd3cdccf2 ("devlink: Add support for dynamic table size")
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflecting IPv6 Flow Label at server nodes is useful in environments
that employ multipath routing to load balance the requests. As "IPv6
Flow Label Reflection" standard draft [1] points out - ICMPv6 PTB error
messages generated in response to a downstream packets from the server
can be routed by a load balancer back to the original server without
looking at transport headers, if the server applies the flow label
reflection. This enables the Path MTU Discovery past the ECMP router in
load-balance or anycast environments where each server node is reachable
by only one path.
Introduce a sysctl to enable flow label reflection per net namespace for
all newly created sockets. Same could be earlier achieved only per
socket by setting the IPV6_FL_F_REFLECT flag for the IPV6_FLOWLABEL_MGR
socket option.
[1] https://tools.ietf.org/html/draft-wang-6man-flow-label-reflection-01
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry clear routine can be shared between the drivers, thus it is
moved inside devlink.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the dpipe table's size was static and known at registration
time. The host table does not have constant size and it is resized in
dynamic manner. In order to support this behavior the size is changed
to be obtained dynamically via an op.
This patch also adjust the current dpipe table for the new API.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv4 host table which will be introduced in the
following patches. This header is global and can be reused by many
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv4 host table which will be introduced in the
following patches. This header is global and can be reused by many
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to find out if a gact instance is goto_chain termination
action and to get chain index.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SOF_TIMESTAMPING_RX_SOFTWARE is enabled for tcp sockets, return the
timestamp corresponding to the highest sequence number data returned.
Previously the skb->tstamp is overwritten when a TCP packet is placed
in the out of order queue. While the packet is in the ooo queue, save the
timestamp in the TCB_SKB_CB. This space is shared with the gso_*
options which are only used on the tx path, and a previously unused 4
byte hole.
When skbs are coalesced either in the sk_receive_queue or the
out_of_order_queue always choose the timestamp of the appended skb to
maintain the invariant of returning the timestamp of the last byte in
the recvmsg buffer.
Signed-off-by: Mike Maloney <maloney@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds ERSPAN type II tunnel support. The implementation
is based on the draft at [1]. One of the purposes is for Linux
box to be able to receive ERSPAN monitoring traffic sent from
the Cisco switch, by creating a ERSPAN tunnel device.
In addition, the patch also adds ERSPAN TX, so Linux virtual
switch can redirect monitored traffic to the ERSPAN tunnel device.
The traffic will be encapsulated into ERSPAN and sent out.
The implementation reuses tunnel key as ERSPAN session ID, and
field 'erspan' as ERSPAN Index fields:
./ip link add dev ers11 type erspan seq key 100 erspan 123 \
local 172.16.1.200 remote 172.16.1.100
To use the above device as ERSPAN receiver, configure
Nexus 5000 switch as below:
monitor session 100 type erspan-source
erspan-id 123
vrf default
destination ip 172.16.1.200
source interface Ethernet1/11 both
source interface Ethernet1/12 both
no shut
monitor erspan origin ip-address 172.16.1.100 global
[1] https://tools.ietf.org/html/draft-foschiano-erspan-01
[2] iproute2 patch: http://marc.info/?l=linux-netdev&m=150306086924951&w=2
[3] test script: http://marc.info/?l=linux-netdev&m=150231021807304&w=2
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Meenakshi Vohra <mvohra@vmware.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the invalid handle "0" check to avoid unnecessary search, because
the qdisc uses the skb->priority as the handle value to look up, and
it is "0" usually.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile tested only, but saw no warnings/errors with
allmodconfig build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-08-21
1) Support RX checksum with IPsec crypto offload for esp4/esp6.
From Ilan Tayari.
2) Fixup IPv6 checksums when doing IPsec crypto offload.
From Yossi Kuperman.
3) Auto load the xfrom offload modules if a user installs
a SA that requests IPsec offload. From Ilan Tayari.
4) Clear RX offload informations in xfrm_input to not
confuse the TX path with stale offload informations.
From Ilan Tayari.
5) Allow IPsec GSO for local sockets if the crypto operation
will be offloaded.
6) Support setting of an output mark to the xfrm_state.
This mark can be used to to do the tunnel route lookup.
From Lorenzo Colitti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This important to call qdisc_tree_reduce_backlog() after changing queue
length. Parent qdisc should deactivate class in ->qlen_notify() called from
qdisc_tree_reduce_backlog() but this happens only if qdisc->q.qlen in zero.
Missed class deactivations leads to crashes/warnings at picking packets
from empty qdisc and corrupting state at reactivating this class in future.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 86a7996cc8 ("net_sched: introduce qdisc_replace() helper")
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit e6afc8ace6 ("udp: remove
headers from UDP packets before queueing"), when udp packets are being
peeked the requested extra offset is always 0 as there is no need to skip
the udp header. However, when the offset is 0 and the next skb is
of length 0, it is only returned once. The behaviour can be seen with
the following python script:
from socket import *;
f=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
g=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
f.bind(('::', 0));
addr=('::1', f.getsockname()[1]);
g.sendto(b'', addr)
g.sendto(b'b', addr)
print(f.recvfrom(10, MSG_PEEK));
print(f.recvfrom(10, MSG_PEEK));
Where the expected output should be the empty string twice.
Instead, make sk_peek_offset return negative values, and pass those values
to __skb_try_recv_datagram/__skb_try_recv_from_queue. If the passed offset
to __skb_try_recv_from_queue is negative, the checked skb is never skipped.
__skb_try_recv_from_queue will then ensure the offset is reset back to 0
if a peek is requested without an offset, unless no packets are found.
Also simplify the if condition in __skb_try_recv_from_queue. If _off is
greater then 0, and off is greater then or equal to skb->len, then
(_off || skb->len) must always be true assuming skb->len >= 0 is always
true.
Also remove a redundant check around a call to sk_peek_offset in af_unix.c,
as it double checked if MSG_PEEK was set in the flags.
V2:
- Moved the negative fixup into __skb_try_recv_from_queue, and remove now
redundant checks
- Fix peeking in udp{,v6}_recvmsg to report the right value when the
offset is 0
V3:
- Marked new branch in __skb_try_recv_from_queue as unlikely.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on yet another syzkaller report, I found
that our IP_MAX_MTU enforcements were not properly done.
gcc seems to reload dev->mtu for min(dev->mtu, IP_MAX_MTU), and
final result can be bigger than IP_MAX_MTU :/
This is a problem because device mtu can be changed on other cpus or
threads.
While this patch does not fix the issue I am working on, it is
probably worth addressing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 routes currently lack nexthop flags as in IPv4. This has several
implications.
In the forwarding path, it requires us to check the carrier state of the
nexthop device and potentially ignore a linkdown route, instead of
checking for RTNH_F_LINKDOWN.
It also requires capable drivers to use the user facing IPv6-specific
route flags to provide offload indication, instead of using the nexthop
flags as in IPv4.
Add nexthop flags to IPv6 routes in the 40 bytes hole and use it to
provide offload indication instead of the RTF_OFFLOAD flag, which is
removed while it's still not part of any official kernel release.
In the near future we would like to use the field for the
RTNH_F_{LINKDOWN,DEAD} flags, but this change is more involved and might
not be ready in time for the current cycle.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZkte/AAoJEG4XJFUm622bjqUH/01JNHIGh7WI2YHm9qA//uC0
L35j/nYwiBX47LREkVhgS2goR3BYihricM1w1uwv/1E/JJqECWVe7rPodoM4sYqh
jVVPy3ZYIK/Kk8i7v2W+VIeqR0b2q4PBt+UtruEBH1o8ESKZPDMqudq+AAbHeiih
tWJpPmS+IFW8yWaF9+v5DhWx5q4/JNvZgmNarS5/aPF+2bTR9Gw0bf8PUdyLip6J
rsv0W9e9SqmVBYkRoC4WMgM/RJbUh1d66SPQ3Yrv/nFL6cTgecC2IxQx7pCGUq9n
LbDJy6HCi+3mBJyMkVVs9iaXZiaNm7eUmEq16ENpiAnsQy5h9i/jVpySC0R/BzQ=
=KXB+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_linear_skb() is broken; both of its callers actually
expect 'len' to be the amount we are trying to copy,
not the offset of the end.
Fix it keeping the meanings of arguments in sync with what the
callers (both of them) expect.
Also restore a saner behavior on EFAULT (i.e. preserving
the iov_iter position in case of failure):
The commit fd851ba9ca ("udp: harden copy_linear_skb()")
avoids the more destructive effect of the buggy
copy_linear_skb(), e.g. no more invalid memory access, but
said function still behaves incorrectly: when peeking with
offset it can fail with EINVAL instead of copying the
appropriate amount of memory.
Reported-by: Sasha Levin <alexander.levin@verizon.com>
Fixes: b65ac44674 ("udp: try to avoid 2 cache miss on dequeue")
Fixes: fd851ba9ca ("udp: harden copy_linear_skb()")
Signed-off-by: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Sasha Levin <alexander.levin@verizon.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIN_NAPI_ID is used in various places outside of
CONFIG_NET_RX_BUSY_POLL wrapping, so when it's not set
we run into build errors such as:
net/core/dev.c: In function 'dev_get_by_napi_id':
net/core/dev.c:886:16: error: ‘MIN_NAPI_ID’ undeclared (first use in this function)
if (napi_id < MIN_NAPI_ID)
^~~~~~~~~~~
Thus, have MIN_NAPI_ID always defined to fix these errors.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch c4adfc822b ("bonding: make speed, duplex setting consistent
with link state") puts the link state to down if
bond_update_speed_duplex() cannot retrieve speed and duplex settings.
Assumably the patch was written with 802.3ad mode in mind which relies
on link speed/duplex settings. For other modes like active-backup these
settings are not required. Thus, only for these other modes, this patch
reintroduces support for slaves that do not support reporting speed or
duplex such as wireless devices. This fixes the regression reported in
bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547).
Fixes: c4adfc822b ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cops->tcf_cl_offload is no longer needed, as the drivers check what they
can and cannot offload using the classid identify helpers. So remove this.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no longer need to use handle in drivers, so remove it from
tc_cls_common_offload struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers need classid to decide they support this specific qdisc+class
or not. So propagate it down via the tc_cls_common_offload struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading drivers need to understand what qdisc class a filter is added
to. Currently they only need to identify ingress, clsact->ingress and
clsact->egress. So provide these helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some bad indents of functions' defination in sm_make_chunk.c.
They have been there since beginning, it was probably caused by that
the typedef sctp_chunk_t was replaced with struct sctp_chunk.
So it's the best time to fix them in this patchset, it's also to fix
some bad indents in other functions' defination in sm_make_chunk.c.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_disposition_t, and
replace with enum sctp_disposition in the places where it's
using this typedef.
It's also to fix the indent for many functions' defination.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_sm_table_entry_t, and
replace with struct sctp_sm_table_entry in the places where it's
using this typedef.
It is also to fix some indents.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove this typedef including the struct, there is even no places
using it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_verb_t, and
replace with enum sctp_verb in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_arg_t, and
replace with union sctp_arg in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_cmd_seq_t, and
replace with struct sctp_cmd_seq in the places where it's
using this typedef.
Note that it doesn't fix many indents although it should,
as sctp_disposition_t's removal would mess them up again.
So better to fix them when removing sctp_disposition_t in
the later patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_cmd_t, and
replace with enum sctp_cmd in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_socket_type_t, and
replace with enum sctp_socket_type in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_dbg_objcnt_entry_t, and
replace with struct sctp_dbg_objcnt_entry in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_cmsgs_t, and
replace with struct sctp_cmsgs in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_endpoint_type_t, and
replace with enum sctp_endpoint_type in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_sender_hb_info_t, and
replace with struct sctp_sender_hb_info in the places where it's
using this typedef.
It is also to use sizeof(variable) instead of sizeof(type).
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove this function typedef, there is even no places
using it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On systems that use mark-based routing it may be necessary for
routing lookups to use marks in order for packets to be routed
correctly. An example of such a system is Android, which uses
socket marks to route packets via different networks.
Currently, routing lookups in tunnel mode always use a mark of
zero, making routing incorrect on such systems.
This patch adds a new output_mark element to the xfrm state and
a corresponding XFRMA_OUTPUT_MARK netlink attribute. The output
mark differs from the existing xfrm mark in two ways:
1. The xfrm mark is used to match xfrm policies and states, while
the xfrm output mark is used to set the mark (and influence
the routing) of the packets emitted by those states.
2. The existing mark is constrained to be a subset of the bits of
the originating socket or transformed packet, but the output
mark is arbitrary and depends only on the state.
The use of a separate mark provides additional flexibility. For
example:
- A packet subject to two transforms (e.g., transport mode inside
tunnel mode) can have two different output marks applied to it,
one for the transport mode SA and one for the tunnel mode SA.
- On a system where socket marks determine routing, the packets
emitted by an IPsec tunnel can be routed based on a mark that
is determined by the tunnel, not by the marks of the
unencrypted packets.
- Support for setting the output marks can be introduced without
breaking any existing setups that employ both mark-based
routing and xfrm tunnel mode. Simply changing the code to use
the xfrm mark for routing output packets could xfrm mark could
change behaviour in a way that breaks these setups.
If the output mark is unspecified or set to zero, the mark is not
set or changed.
Tested: make allyesconfig; make -j64
Tested: https://android-review.googlesource.com/452776
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
David Lebrun
Eric Biggers
Jakub Sitnicki
David S. Miller
Arkadi Sharshevsky
Jiri Pirko
Antoine Ténart
Mike Maloney
William Tu
Tonghao Zhang
Gao Feng
Florian Westphal
Konstantin Khlebnikov
Eric Dumazet
Matthew Dawson
Ido Schimmel
Al Viro
Daniel Borkmann
Andreas Born
Xin Long
Lorenzo Colitti