Commit c98929c07a removed the clearing of the FPSCR[31:28] bits from the
vfp_raise_exceptions() function and the new bits are or'ed with the old
FPSCR bits leading to unexpected results (the original commit was
referring to the cumulative bits - FPSCR[4:0]).
Reported-by: Tom Hameenanttila <tmhameen@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DBDMA descriptors need to be located at 32-byte aligned addresses;
however kmalloc in conjunction with the SLAB allocator and
CONFIG_DEBUG_SLUB enabled doesn't deliver any. The dbdma code works
around that by allocating a larger area and realigning the start
address within it.
When freeing a channel however this adjustment is not taken into
account which results in an oops:
Kernel bug detected[#1]:
[...]
Call Trace:
[<80186010>] cache_free_debugcheck+0x284/0x318
[<801869d8>] kfree+0xe8/0x2a0
[<8010b31c>] au1xxx_dbdma_chan_free+0x2c/0x7c
[<80388dc8>] au1x_pcm_dbdma_free+0x34/0x4c
[<80388fa8>] au1xpsc_pcm_close+0x28/0x38
[<80383cb8>] soc_codec_close+0x14c/0x1cc
[<8036dbb4>] snd_pcm_release_substream+0x60/0xac
[<8036dc40>] snd_pcm_release+0x40/0xa0
[<8018c7a8>] __fput+0x11c/0x228
[<80188f60>] filp_close+0x7c/0x98
[<80189018>] sys_close+0x9c/0xe4
[<801022a0>] stack_done+0x20/0x3c
Fix this by recording the address delivered by kmalloc() and using
it as parameter to kfree().
This fix is only necessary with the SLAB allocator and CONFIG_DEBUG_SLAB
enabled; non-debug SLAB, SLUB do return nicely aligned addresses,
debug-enabled SLUB currently panics early in the boot process.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, hw_breakpoint, kgdb: Do not take mutex for kernel debugger
x86, hw_breakpoints, kgdb: Fix kgdb to use hw_breakpoint API
hw_breakpoints: Release the bp slot if arch_validate_hwbkpt_settings() fails.
perf: Ignore perf.data.old
perf report: Fix segmentation fault when running with '-g none'
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init regression
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
x86: Add Dell OptiPlex 760 reboot quirk
x86, UV: Fix RTC latency bug by reading replicated cachelines
oprofile/x86: add Xeon 7500 series support
oprofile/x86: fix crash when profiling more than 28 events
lib/dma-debug.c: mark file-local struct symbol static.
x86/amd-iommu: Fix deassignment of a device from the pt_domain
x86/amd-iommu: Fix IOMMU-API initialization for iommu=pt
x86/amd-iommu: Fix NULL pointer dereference in __detach_device()
x86/amd-iommu: Fix possible integer overflow
Here are the powerpc bits to remove TIF_ABI_PENDING now that
set_personality() is called at the appropriate place in exec.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
desc->affinity doesn't exit in that case. Let's use a macro for
the UP variant of get_irq_server(), it's the easiest way, avoids
evaluating arguments.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Current behaviour is to generate the IT instruction only for Thumb-2
code. However, the kernel helpers in entry-armv.S are compiled to ARM in
a unified syntax file (if THUMB2_KERNEL). Recent compilers warn about
missing IT instruction in unified assembly syntax files. The patch
changes the "-mimplicit-it" gas option to "always".
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the regression in functionality where the
kernel debugger and the perf API do not nicely share hw
breakpoint reservations.
The kernel debugger cannot use any mutex_lock() calls because it
can start the kernel running from an invalid context.
A mutex free version of the reservation API needed to get
created for the kernel debugger to safely update hw breakpoint
reservations.
The possibility for a breakpoint reservation to be concurrently
processed at the time that kgdb interrupts the system is
improbable. Should this corner case occur the end user is
warned, and the kernel debugger will prohibit updating the
hardware breakpoint reservations.
Any time the kernel debugger reserves a hardware breakpoint it
will be a system wide reservation.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: torvalds@linux-foundation.org
LKML-Reference: <1264719883-7285-3-git-send-email-jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the 2.6.33 kernel, the hw_breakpoint API is now used for the
performance event counters. The hw_breakpoint_handler() now
consumes the hw breakpoints that were previously set by kgdb
arch specific code. In order for kgdb to work in conjunction
with this core API change, kgdb must use some of the low level
functions of the hw_breakpoint API to install, uninstall, and
deal with hw breakpoint reservations.
The kgdb core required a change to call kgdb_disable_hw_debug
anytime a slave cpu enters kgdb_wait() in order to keep all the
hw breakpoints in sync as well as to prevent hitting a hw
breakpoint while kgdb is active.
During the architecture specific initialization of kgdb, it will
pre-allocate 4 disabled (struct perf event **) structures. Kgdb
will use these to manage the capabilities for the 4 hw
breakpoint registers, per cpu. Right now the hw_breakpoint API
does not have a way to ask how many breakpoints are available,
on each CPU so it is possible that the install of a breakpoint
might fail when kgdb restores the system to the run state. The
intent of this patch is to first get the basic functionality of
hw breakpoints working and leave it to the person debugging the
kernel to understand what hw breakpoints are in use and what
restrictions have been imposed as a result. Breakpoint
constraints will be dealt with in a future patch.
While atomic, the x86 specific kgdb code will call
arch_uninstall_hw_breakpoint() and arch_install_hw_breakpoint()
to manage the cpu specific hw breakpoints.
The net result of these changes allow kgdb to use the same pool
of hw_breakpoints that are used by the perf event API, but
neither knows about future reservations for the available hw
breakpoint slots.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: torvalds@linux-foundation.org
LKML-Reference: <1264719883-7285-2-git-send-email-jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 6aa542a694 added a quirk for the
Intel DG45ID board due to low memory corruption. The Intel DG45FC
shares the same BIOS (and the same bug) as noted in:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: David Härdeman <david@hardeman.nu>
LKML-Reference: <20100128200254.GA9134@hardeman.nu>
Cc: <stable@kernel.org>
Cc: Alexey Fisher <bug-track@fisher-privat.net>
Cc: ykzhao <yakui.zhao@intel.com>
Cc: Tony Bones <aabonesml@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The only usage of _toggle_gpio_edge_triggering is in
an #ifdef CONFIG_ARCH_OMAP1 block, so only provide it if
CONFIG_ARCH_OMAP1 is defined, too.
This fixes a compiler warning:
arch/arm/plat-omap/gpio.c:758: warning: '_toggle_gpio_edge_triggering' defined but not used
when compiling for ARCH_OMAP2, ARCH_OMAP3 or ARCH_OMAP4.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here are the sparc bits to remove TIF_ABI_PENDING now that
set_personality() is called at the appropriate place in exec.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the previous commit made it possible to do the personality
setting at the point of no return, we do just that for ELF binaries.
And suddenly all the reasons for that insane TIF_ABI_PENDING bit go
away, and we can just make SET_PERSONALITY() just do the obvious thing
for a 32-bit compat process.
Everything becomes much more straightforward this way.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'flush_old_exec()' is the point of no return when doing an execve(), and
it is pretty badly misnamed. It doesn't just flush the old executable
environment, it also starts up the new one.
Which is very inconvenient for things like setting up the new
personality, because we want the new personality to affect the starting
of the new environment, but at the same time we do _not_ want the new
personality to take effect if flushing the old one fails.
As a result, the x86-64 '32-bit' personality is actually done using this
insane "I'm going to change the ABI, but I haven't done it yet" bit
(TIF_ABI_PENDING), with SET_PERSONALITY() not actually setting the
personality, but just the "pending" bit, so that "flush_thread()" can do
the actual personality magic.
This patch in no way changes any of that insanity, but it does split the
'flush_old_exec()' function up into a preparatory part that can fail
(still called flush_old_exec()), and a new part that will actually set
up the new exec environment (setup_new_exec()). All callers are changed
to trivially comply with the new world order.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the newer 4xx pci cores need an explicit bit set to send
type 1 transactions instead of just comparing the bus numbers.
This patch enables type 1 transations for pcix nodes, thus enabling
devices behind PCI bridges.
Signed-off-by: Stef van Os <stef.van.os@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add missing call to pci_fixup_device(pci_fixup_early, ...) when
building the pci_dev from scratch off the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add missing hookup to existing pci_slot when building the pci_dev from
scratch off the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: remove IOH range fetching
PCI: fix nested spinlock hang in aer_inject
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Update mach-types
[ARM] orion5x: D-link DNS-323 rev. B1 power-off
[ARM] Orion5x: add GPIO LED and buttons for wrt350n v2
[ARM] pxa: fix irq suspend/resume for pxa25x
[ARM] pxa: fix the incorrect naming of AC97 reset pin config for pxa26x
[ARM] pxa/corgi: fix incorrect default GPIO for UDC Vbus
[ARM] Kirkwood: drive USB VBUS pin on rd88f6192-nas high on boot
[ARM] Orion: fix PCIe inbound window programming when RAM size is not a power of two
Turned out to cause trouble on single IOH machines, and is superceded by
_CRS on multi-IOH machines with production BIOSes.
Signed-off-by: Jeff Garrett <jeff@jgarrett.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Dell OptiPlex 760 hangs on reboot unless reboot=bios is used. Add quirk
to reboot through the BIOS.
BugLink: https://bugs.launchpad.net/bugs/488319
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
LKML-Reference: <1264634958.27335.1091.camel@emiko>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The MIPS processor is limited to 64 external interrupt sources. Using a
greater number without IRQ sharing requires reading platform-specific
registers. On such platforms, reading the IntCtl register to determine
which interrupt corresponds to a timer interrupt will not work.
On MIPSR2 systems there is a solution - the TI bit in the Cause register,
specifically indicates that a timer interrupt has occured. This patch uses
that bit to detect interrupts for MIPSR2 processors, which may be expected
to work regardless of how the timer interrupt may be routed in the hardware.
Signed-off-by: David VomLehn (dvomlehn@cisco.com)
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pre-compute addresses for the basic ASIC registers. This speeds up access
and allows memory for unused configurations to be freed. In addition,
uninitialized register addresses will be returned as NULL to catch bad
usage quickly.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
POSIX requires $((<expression>)) arithmetic in sh only to have long
arithmetic so on 32-bit sh binaries might do only 32-bit arithmetic but
the arithmetic done in arch/mips/boot/compressed/Makefile needs 64-bit.
I play with the AR7 platform, so VMLINUX_LOAD_ADDRESS is
0xffffffff94100000, and for an example 4MiB kernel
VMLINUZ_LOAD_ADDRESS is made out to be:
----
alex@berk:~$ bash -c 'printf "%x\n" $((0xffffffff94100000 + 0x400000))'
ffffffff94500000
alex@berk:~$ dash -c 'printf "%x\n" $((0xffffffff94100000 + 0x400000))'
80000000003fffff
----
The former is obviously correct whilst the later breaks things royally.
Fortunately working with only the lower 32bit's works for both bash and
dash:
----
$ bash -c 'printf "%x\n" $((0x94100000 + 0x400000))'
94500000
$ dash -c 'printf "%x\n" $((0x94100000 + 0x400000))'
94500000
----
So, we can split the original 64bit string to two parts, and only
calculate the low 32bit part, which is big enough (1GiB kernel sizes
anyone?) for a normal Linux kernel image file, now, we calculate the
VMLINUZ_LOAD_ADDRESS like this:
1. if present, append top 32bit of VMLINUX_LOAD_ADDRESS" as a prefix
2. get the sum of the low 32bit of VMLINUX_LOAD_ADDRESS + VMLINUX_SIZE
This patch fixes vmlinuz kernel builds on systems where only a
32bit-only math shell is available.
Patch Changelog:
Version 2
- simplified method by using 'expr' for 'substr' and making it work
with dash once again
Version 1
- Revert the removals of '-n "$(VMLINUX_SIZE)"' to avoid the error
of "make clean"
- Consider more cases of the VMLINUX_LOAD_ADDRESS
Version 0
- initial release
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/861/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Patchwork: http://patchwork.linux-mips.org/patch/857/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] fix single stepped svcs with TRACE_IRQFLAGS=y
[S390] zcrypt: Do not remove coprocessor for error 8/72
[S390] sclp_vt220: set initial terminal window size
[S390] use set_current_state in sigsuspend
[S390] irqflags: add missing types.h include
[S390] dasd: fix possible NULL pointer errors
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, msr/cpuid: Pass the number of minors when unregistering MSR and CPUID drivers.
x86: Remove "x86 CPU features in debugfs" (CONFIG_X86_CPU_DEBUG)
Revert "x86: ucode-amd: Load ucode-patches once ..."
x86: Disable HPET MSI on ATI SB700/SB800
x86: Set hotpluggable nodes in nodes_possible_map
For SGI UV node controllers (HUB) rev 2.0 or greater, use
replicated cachelines to read the RTC timer. This optimization
allows faster simulataneous reads from a given socket.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100122154140.GB4975@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If irq flags tracing is enabled the TRACE_IRQS_ON macros expands to
a function call which clobbers registers %r0-%r5. The macro is used
in the code path for single stepped system calls. The argument
registers %r2-%r6 need to be restored from the stack before the system
call function is called.
Cc: stable@kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use set_current_state instead of a direct assignment to set the
task state of the current process.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add missing types.h include. Otherwise would cause build breakages on
hw breakpoint support, because of undefined BITS_PER_LONG.
Also fix up the copyright line and remove the superfluous __KERNEL__
ifdef.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pass the number of minors when unregistering MSR and CPUID drivers.
Reported-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
LKML-Reference: <20100127023722.GA22305@sgi.com>
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This makes the FEC clock configuration consistent with the UART one.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The gpt_clk rate function doesn't consider the PER divider. This causes a
significant drift in time accounting. Fix this by introducing the correct rate
calculation function.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch disables all unnecessary clock in mx25_clocks_init() to make a clean
start, the same as is being done for the rest of the i.MX chips.
This patch was tested on i.MX25 PDK.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fref is needless on mx25 since the reference clock is fixed at 24MHz.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Can't reference irq_desc[].affinity when !SMP.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix leak of free lapic date in kvm_arch_vcpu_init()
KVM: x86: Fix probable memory leak of vcpu->arch.mce_banks
KVM: S390: fix potential array overrun in intercept handling
KVM: fix spurious interrupt with irqfd
eventfd - allow atomic read and waitqueue remove
KVM: MMU: bail out pagewalk on kvm_read_guest error
KVM: properly check max PIC pin in irq route setup
KVM: only allow one gsi per fd
KVM: x86: Fix host_mapping_level()
KVM: powerpc: Show timing option only on embedded
KVM: Fix race between APIC TMR and IRR
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (25 commits)
OMAP2/3: DMTIMER: Clear pending interrupts when stopping a timer
PM debug: Fix warning when no CONFIG_DEBUG_FS
OMAP3: PM: DSS PM_WKEN to refill DMA
OMAP: timekeeping: time should not stop during suspend
OMAP3: PM: Force write last pad config register into save area
OMAP: omap3_pm_get_suspend_state() error ignored in pwrdm_suspend_get()
OMAP3: PM: Enable wake-up from McBSP2, 3 and 4 modules
OMAP3: PM debug: fix build error when !CONFIG_DEBUG_FS
OMAP3: PM: Removing redundant and potentially dangerous PRCM configration
OMAP3: Fixed ARM aux ctrl register save/restore
OMAP3: CPUidle: Fixed timer resolution
OMAP3: PM: Remove duplicate code blocks
OMAP3: PM: Disable interrupt controller AUTOIDLE before WFI
OMAP3: PM: Enable system control module autoidle
OMAP3: PM: Ack pending interrupts before entering suspend
omap: Enable GPMC clock in gpmc_init
OMAP1 clock: fix for "BUG: spinlock lockup on CPU#0"
OMAP4: clocks: Fix the clksel_rate struct DPLL divs
OMAP4: PRCM: Fix the base address for CHIRONSS reg defines
OMAP: dma_chan[lch_head].flag & OMAP_DMA_ACTIVE tested twice in omap_dma_unlink_lch()
...
Add Xeon 7500 series support to oprofile.
Straight forward: it's the same as Core i7, so just detect
the model number. No user space changes needed.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
With multiplexing enabled oprofile crashs when profiling more than 28
events. This patch fixes this.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
In function kvm_arch_vcpu_init(), if the memory malloc for
vcpu->arch.mce_banks is fail, it does not free the memory
of lapic date. This patch fixed it.
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
vcpu->arch.mce_banks is malloc in kvm_arch_vcpu_init(), but
never free in any place, this may cause memory leak. So this
patch fixed to free it in kvm_arch_vcpu_uninit().
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
kvm_handle_sie_intercept uses a jump table to get the intercept handler
for a SIE intercept. Static code analysis revealed a potential problem:
the intercept_funcs jump table was defined to contain (0x48 >> 2) entries,
but we only checked for code > 0x48 which would cause an off-by-one
array overflow if code == 0x48.
Use the compiler and ARRAY_SIZE to automatically set the limits.
Cc: stable@kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Exit the guest pagetable walk loop if reading gpte failed. Otherwise its
possible to enter an endless loop processing the previous present pte.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When found a error hva, should not return PAGE_SIZE but the level...
Also clean up the coding style of the following loop.
Cc: stable@kernel.org
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Embedded PowerPC KVM has an exit timing implementation to track and evaluate
how much time was spent in which exit path.
For Book3S, we don't implement it. So let's not expose it as a config option
either.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we queue an interrupt to the local apic, we set the IRR before the TMR.
The vcpu can pick up the IRR and inject the interrupt before setting the TMR,
and perhaps even EOI it, causing incorrect behaviour.
The race is really insignificant since it can only occur on the first
interrupt (usually following interrupts will not change TMR), but it's better
closed than open.
Fixed by reordering setting the TMR vs IRR.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fixes power LED blinking and power-off on DNS-323 rev. B1.
GPIO pin 3 has to be set to 1 to stop power LED blinking and to allow the LED to be controlled via leds-gpio. This pin has to be also set to 1 for power-off to work.
To power-off the rev. B1 machine, pin 8 has to be set to 1 and then set to 0 to do actual power-off.
Tested on my DNS-323 rev. B1
Signed-off-by: Erik Benada <erikbenada@yahoo.ca>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
CONFIG_X86_CPU_DEBUG, which provides some parsed versions of the x86
CPU configuration via debugfs, has caused boot failures on real
hardware. The value of this feature has been marginal at best, as all
this information is already available to userspace via generic
interfaces.
Causes crashes that have not been fixed + minimal utility -> remove.
See the referenced LKML thread for more information.
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <alpine.LFD.2.00.1001221755320.13231@localhost.localdomain>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Commit d1c84f79a6
leads to a regression when microcode_amd.c is compiled into the kernel.
It causes a big boot delay because the firmware is not available.
See http://marc.info/?l=linux-kernel&m=126267290920060
It also renders the reload sysfs attribute useless.
Fixing this is too intrusive for an -rc5 kernel.
Thus I'd like to restore the microcode loading behaviour of kernel
2.6.32.
CC: Gene Heskett <gene.heskett@verizon.net>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100122203456.GB13792@alberich.amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
HPET MSI on platforms with ATI SB700/SB800 as they seem to have some
side-effects on floppy DMA. Do not use HPET MSI on such platforms.
Original problem report from Mark Hounschell
http://lkml.indiana.edu/hypermail/linux/kernel/0912.2/01118.html
[ This patch needs to go to stable as well. But, there are some
conflicts that prevents the patch from going as is. I can
rebase/resubmit to stable once the patch goes upstream.
hpa: still Cc:'ing stable@ as an FYI. ]
Tested-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
LKML-Reference: <20100121190952.GA32523@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
nodes_possible_map does not currently include nodes that have SRAT
entries that are all ACPI_SRAT_MEM_HOT_PLUGGABLE since the bit is
cleared in nodes_parsed if it does not have an online address range.
Unequivocally setting the bit in nodes_parsed is insufficient since
existing code, such as acpi_get_nodes(), assumes all nodes in the map
have online address ranges. In fact, all code using nodes_parsed
assumes such nodes represent an address range of online memory.
nodes_possible_map is created by unioning nodes_parsed and
cpu_nodes_parsed; the former represents nodes with online memory and
the latter represents memoryless nodes. We now set the bit for
hotpluggable nodes in cpu_nodes_parsed so that it also gets set in
nodes_possible_map.
[ hpa: Haicheng Li points out that this makes the naming of the
variable cpu_nodes_parsed somewhat counterintuitive. However, leave
it as is in the interest of keeping the pure bug fix patch small. ]
Signed-off-by: David Rientjes <rientjes@google.com>
Tested-by: Haicheng Li <haicheng.li@linux.intel.com>
LKML-Reference: <alpine.DEB.2.00.1001201152040.30528@chino.kir.corp.google.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Deassigning a device from the passthrough domain does not
work and breaks device assignment to kvm guests. This patch
fixes the issue.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch moves the initialization of the iommu-api out of
the dma-ops initialization code. This ensures that the
iommu-api is initialized even with iommu=pt.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
In the __detach_device function the reference count for a
device-domain binding may become zero. This results in the
device being removed from the domain and dev_data->domain
will be NULL. This is bad because this pointer is
dereferenced when trying to unlock the domain->lock. This
patch fixes the issue by keeping the domain in a seperate
variable.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The variable i in this function could be increased to over
2**32 which would result in an integer overflow when using
int. Fix it by changing i to unsigned long.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
OMAP GP timers keep running for a few cycles after they are stopped,
which can cause the timer to expire and generate an interrupt. The
pending interrupt will prevent e.g. OMAP from entering suspend, thus
we ack it manually. Only applicable on OMAP2/3/4.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cfc38999f (backlight: Pass device through notify callback)
added a struct device argument to the notify callback, but didn't
update the user of it in mach-hmt.c
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI: delete acpi_processor_power_verify_c2()
ACPI: allow C3 > 1000usec
ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
ACPI: power_meter: remove double kfree()
ACPI: processor: restrict early _PDC to opt-in platforms
ACPI: Fix unused variable warning in sbs.c
acpi: make ACPI device id constant
sony-laptop - fix using of uninitialized variable
ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
eeepc-laptop: disable wireless hotplug for 1201N
eeepc-laptop: add hotplug_disable parameter
eeepc-laptop: switch to using sparse keymap library
eeepc-laptop: dmi blacklist to disable pci hotplug code
eeepc-laptop: disable cpu speed control on EeePC 701
ACPI: don't cond_resched if irq is disabled
ACPI: Remove unnecessary cast.
ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
ACPI: EC: Add wait for irq storm
ACPI: SBS: Move SBS HC callback to faster Notify queue
x86, ACPI: delete acpi_boot_table_init() return value
...
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
ARM: 5884/1: arm: Fix DCC console for v7
ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
ARM: fix badly placed mach/plat entries in Kconfig & Makefile
To distinguish between mx31lite and mx31lilly boards better to use
different enum types.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: Stephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As noted by Benjamin Herrenschmidt, the generic IRQ layer
only sets irq_desc[irq].affinity after ->set_affinity()
succeeds.
So we have to use the passed in cpumask.
Signed-off-by: David S. Miller <davem@davemloft.net>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warning when CONFIG_DEBUG_FS wasn't selected:
arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, DSS does not wakeup when there is a DMA request. DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
During suspend, the kernel timekeeping subsystem is shut down. Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.
This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.
This patch uses the 32k sync timer as a the persistent clock.
NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
more than one wrapping of the 32k sync timer during suspend may
cause problems. Also note there are not interrupts when the 32k
sync timer wraps, so something else has to be done.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.
Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
val is an u64 pointer, we need an int to check the error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.
Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1
This patch fixes the above errors.
Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Previously used u32 as temporary data storage that wraps around at 4.294s.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Marek Skuczynski
Russell King
Catalin Marinas
Alexander Clouter
Manuel Lauss
Linus Torvalds
Andreas Schwab
Benjamin Herrenschmidt
Colin Tuckley
Jason Wessel
David Härdeman
Uwe Kleine-König
David Miller
H. Peter Anvin
Stef van Os
Jeff Garrett
Leann Ogasawara
David VomLehn
Wu Zhangjin
Dimitri Sivanich
Ingo Molnar
Martin Schwidefsky
Heiko Carstens
Russ Anderson
Baruch Siach
Sascha Hauer
Andi Kleen
Suravee Suthikulpanit
Wei Yongjun
Christian Borntraeger
Marcelo Tosatti
Sheng Yang
Alexander Graf
Avi Kivity
Erik Benada
Andreas Herrmann
Pallipadi, Venkatesh
David Rientjes
Joerg Roedel
Tero Kristo
Peter Korsgaard
Vladimir Zapolskiy
Stephane Eranian
Anton Blanchard
Tony Lindgren
Sergio Aguirre
Subramani Venkatesh
Kevin Hilman
Roel Kluin
Peter Ujfalusi
Manjunatha GK
Sripathy, Vishwanath
Sanjeev Premi