There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure that the reset is successful by issuing a dummy read to R
channel current register and check its default value. On some platforms,
without this dummy read, any further access to {R/G/B}_EXEC will not have
any impact.
[akpm@linux-foundation.org: fix up code comment]
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: Naga Radhesh <naga.radheshy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depending on the implementation of the hardware blinking function in
blink_set(), the led can support hardware blinking for some values of
delay_on and delay_off and fall-back to software blinking for some other
values.
Turning off the blink_timer unconditionally before starting to blink
make sure that a sequence like:
OFF
hardware blinking
software blinking
hardware blinking
does not leave the software blinking timer active.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I get the following warning:
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:1559 __gpio_get_value+0x90/0x98()
Modules linked in:
Call Trace:
[<ffffffff81440950>] dump_stack+0x8/0x34
[<ffffffff81141478>] warn_slowpath_common+0x78/0xa0
[<ffffffff812f0958>] __gpio_get_value+0x90/0x98
[<ffffffff81434f04>] create_gpio_led+0xdc/0x194
[<ffffffff8143524c>] gpio_led_probe+0x290/0x36c
[<ffffffff8130e8b0>] driver_probe_device+0x78/0x1b0
[<ffffffff8130eaa8>] __driver_attach+0xc0/0xc8
[<ffffffff8130d7ac>] bus_for_each_dev+0x64/0xb0
[<ffffffff8130e130>] bus_add_driver+0x1c8/0x2a8
[<ffffffff8130f100>] driver_register+0x90/0x180
[<ffffffff81100438>] do_one_initcall+0x38/0x160
---[ end trace ee38723fbefcd65c ]---
My GPIOs are on an I2C port expander, so we must use the *_cansleep()
variant of the GPIO functions. This is was not being done in
create_gpio_led().
We can change gpio_get_value() to gpio_get_value_cansleep() because it is
only called from the platform_driver probe function, which is a context
where we can sleep.
Only tested on my gpio_cansleep() system, but it seems safe for all
systems.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Trent Piepho <tpiepho@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the comments in include/linux/init.h:
"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."
We have __devexit annotation for lm3530_remove(), so add __devexit_p to
the `struct i2c_driver'.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If lp5521_read fails, engine_state variable is not initialized.
If lp5521_read fails, we should return error.
This patch fixes below warning.
CC drivers/leds/leds-lp5521.o
drivers/leds/leds-lp5521.c: In function 'lp5521_set_engine_mode':
drivers/leds/leds-lp5521.c:168: warning: 'engine_state' may be used uninitialized in this function
[akpm@linux-foundation.org: remove unneeded "ret |="]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the platform_data include directory for the TPU LED driver, as
suggested by Paul Mundt.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a workqueue in the Renesas TPU LED driver to allow the Runtime PM code
to sleep.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile, the core
will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memory for struct led_trigger should be kfreed in the
led_trigger_register() error path. Also this function should return NULL
on error.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.
The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.
Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.
The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control. Hardware blink is unsupported.
The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board. Tested with experimental sh7372 A3SP power domain
patches. Platform device bind/unbind tested ok.
V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.
[axel.lin@gmail.com: include linux/module.h]
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rename of corgibl_limit_intensity is missed in commit d00ba726
("backlight: Rename the corgi backlight driver to generic"). Let's fix it
now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using gpio_request_one can make the error handling simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regulator support in the l4f00242t03 is very non-idiomatic. Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data. The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.
Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver. As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.
The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile, the core
will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 6c536e4ce8 ("ad525x_dpot: add support for SPI parts") added
support for the AD5161 through SPI, but the device supports both I2C and
SPI (depending on the DIS pin), so add it to -i2c as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regulator API contains a range of features for stubbing itself out
when not in use and for transparently restricting the actual effect of
regulator API calls where they can't be supported on a particular system
so that drivers don't need to individually implement this. Simplify the
driver slightly by making use of this idiom.
The only in tree user is ecovec24 which does not use the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change exported functions to use the device given as parameter
instead of the global one.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After an "unexpected" reboot, I found this Oops in my logs:
divide error: 0000 [#1] PREEMPT SMP=20
CPU 0=20
Modules linked in: lis3lv02d hp_wmi input_polldev [...]
Pid: 390, comm: modprobe Tainted: G C 2.6.39-rc7-wl+=20
RIP: 0010:[<ffffffffa014b427>] [<ffffffffa014b427>]
lis3lv02d_poweron+0x4e/0x94 [lis3lv02d]
RSP: 0018:ffff8801d6407cf8 EFLAGS: 00010246
RAX: 0000000000000bb8 RBX: ffffffffa014e000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffea00066e4708 RDI: ffff8801df002700
RBP: ffff8801d6407d18 R08: ffffea00066c5a30 R09: ffffffff812498c9
R10: ffff8801d7bfcea0 R11: ffff8801d7bfce10 R12: 0000000000000bb8
R13: 00000000ffffffda R14: ffffffffa0154120 R15: ffffffffa0154030
=46S: 00007fc0705db700(0000) GS:ffff8801dfa00000(0000) knlGS:0
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f33549174f0 CR3: 00000001d65c9000 CR4: 00000000000406f0
Process modprobe (pid: 390, threadinfo ffff8801d6406000, task ffff8801d6b40=
000)
Stack:
ffffffffa0154120 62ffffffa0154030 ffffffffa014e000 00000000ffffffea
ffff8801d6407d58 ffffffffa014bcc1 0000000000000000 0000000000000048
ffff8801d8bae800 00000000ffffffea 00000000ffffffda ffffffffa0154120
Call Trace:
[<ffffffffa014bcc1>] lis3lv02d_init_device+0x1ce/0x496 [lis3lv02d]
[<ffffffffa01522ff>] lis3lv02d_add+0x10f/0x17c [hp_accel]
[<ffffffff81233e11>] acpi_device_probe+0x49/0x117
[...]
Code: 3a 75 06 80 4d ef 50 eb 04 80 4d ef 40 0f b6 55 ef be 21
00 00 00 48 89 df ff 53 18 44 8b 63 6c e8 3e fc ff ff 89 c1 44
89 e0 99 <f7> f9 89 c7 e8 93 82 ef e0 48 83 7b 30 00 74 2d 45
31 e4 80 7b=20
RIP [<ffffffffa014b427>] lis3lv02d_poweron+0x4e/0x94 [lis3lv02d]
RSP <ffff8801d6407cf8>
>From my POV, it looks like the hardware is not working as expected
and returns a bogus data rate. The driver doesn't check the result
and directly uses it as some sort of divisor in some places:
msleep(lis3->pwron_delay / lis3lv02d_get_odr());
Under this circumstances, this could very well cause the
"divide by zero" exception from above.
For now, I fixed it the easiest and most obvious way:
Check if the result is sane and if it isn't use a sane default
instead. I went for "100" in the latter case, simply because
/sys/devices/platform/lis3lv02d/rate returns it on a successful
boot.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A straightforward looking use of idr for a device id.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hwmon was using an idr with a NULL pointer, so convert to an
ida which then allows use of Rusty's ida_simple_get.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some kernel components pin user space memory (infiniband and perf) (by
increasing the page count) and account that memory as "mlocked".
The difference between mlocking and pinning is:
A. mlocked pages are marked with PG_mlocked and are exempt from
swapping. Page migration may move them around though.
They are kept on a special LRU list.
B. Pinned pages cannot be moved because something needs to
directly access physical memory. They may not be on any
LRU list.
I recently saw an mlockalled process where mm->locked_vm became
bigger than the virtual size of the process (!) because some
memory was accounted for twice:
Once when the page was mlocked and once when the Infiniband
layer increased the refcount because it needt to pin the RDMA
memory.
This patch introduces a separate counter for pinned pages and
accounts them seperately.
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Mike Marciniszyn <infinipath@qlogic.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a fairly serious bug in RAID10.
When a RAID10 array is degraded and a hot-spare is activated, the
spare does not take up the empty slot, but rather replaces the first
working device.
This is likely to make the array non-functional. It would normally
be possible to recover the data, but that would need care and is not
guaranteed.
This bug was introduced in commit
2bb77736ae
which first appeared in 3.1.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Functions for byte-swapped smbus_write/read_word_data
i2c-algo-pca: Return standard fault codes
i2c-algo-bit: Return standard fault codes
i2c-algo-bit: Be verbose on bus testing failure
i2c-algo-bit: Let user test buses without failing
i2c/scx200_acb: Fix section mismatch warning in scx200_pci_drv
i2c: I2C_ELEKTOR should depend on HAS_IOPORT
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (33 commits)
iommu/core: Remove global iommu_ops and register_iommu
iommu/msm: Use bus_set_iommu instead of register_iommu
iommu/omap: Use bus_set_iommu instead of register_iommu
iommu/vt-d: Use bus_set_iommu instead of register_iommu
iommu/amd: Use bus_set_iommu instead of register_iommu
iommu/core: Use bus->iommu_ops in the iommu-api
iommu/core: Convert iommu_found to iommu_present
iommu/core: Add bus_type parameter to iommu_domain_alloc
Driver core: Add iommu_ops to bus_type
iommu/core: Define iommu_ops and register_iommu only with CONFIG_IOMMU_API
iommu/amd: Fix wrong shift direction
iommu/omap: always provide iommu debug code
iommu/core: let drivers know if an iommu fault handler isn't installed
iommu/core: export iommu_set_fault_handler()
iommu/omap: Fix build error with !IOMMU_SUPPORT
iommu/omap: Migrate to the generic fault report mechanism
iommu/core: Add fault reporting mechanism
iommu/core: Use PAGE_SIZE instead of hard-coded value
iommu/core: use the existing IS_ALIGNED macro
iommu/msm: ->unmap() should return order of unmapped page
...
Fixup trivial conflicts in drivers/iommu/Makefile: "move omap iommu to
dedicated iommu folder" vs "Rename the DMAR and INTR_REMAP config
options" just happened to touch lines next to each other.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Cleanup return type of amd64_determine_edac_cap()
amd64_edac: Add a fix for Erratum 505
EDAC, MCE, AMD: Simplify NB MCE decoder interface
EDAC, MCE, AMD: Drop local coreid reporting
EDAC, MCE, AMD: Print valid addr when reporting an error
EDAC, MCE, AMD: Print CPU number when reporting the error
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
video: platinumfb: Add __devexit_p at necessary place
drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
drivers/video: fsl-diu-fb: remove unused panel operating mode support
drivers/video: fsl-diu-fb: use an enum for the AOI index
drivers/video: fsl-diu-fb: add several new video modes
drivers/video: fsl-diu-fb: remove broken screen blanking support
drivers/video: fsl-diu-fb: move some definitions out of the header file
drivers/video: fsl-diu-fb: fix some ioctls
video: da8xx-fb: Increased resolution configuration of revised LCDC IP
OMAPDSS: picodlp: add missing #include <linux/module.h>
fb: fix au1100fb bitrot.
mx3fb: fix NULL pointer dereference in screen blanking.
video: irq: Remove IRQF_DISABLED
smscufx: change edid data to u8 instead of char
OMAPDSS: DISPC: zorder support for DSS overlays
OMAPDSS: DISPC: VIDEO3 pipeline support
OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
video/omap: fix build dependencies
...
Fix up conflicts in:
- drivers/staging/xgifb/XGI_main_26.c
Changes to XGIfb_pan_var()
- drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
Removed (or in the case of apollon.c, merged into the generic
DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
Adjust i2c-algo-pca to return fault codes compliant with
Documentation/i2c/fault-codes, rather than the undocumented and
vague -EREMOTEIO.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Adjust i2c-algo-bit to return fault codes compliant with
Documentation/i2c/fault-codes, rather than the undocumented and
vague -EREMOTEIO.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If bus testing fails due to the bus being seen as busy, it might be
helpful for developers to know which line is unexpectedly low.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Always failing to register I2C buses when the line testing fails is a
little harsh. While such a failure is definitely a bug in the driver
that exposes the affected I2C bus, things may still work fine if the
missing initialization steps are done later, before the I2C bus is
used. So it seems a better debugging tool to just report the test
failure by default. I introduce bit_test=2 if anyone really misses the
original behavior of bit_test=1.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
WARNING: drivers/i2c/busses/built-in.o(.data+0x47c8): Section mismatch in reference from the variable scx200_pci_drv to the function .devinit.text:scx200_probe()
The variable scx200_pci_drv references
the function __devinit scx200_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Harvey Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On m68k, I get:
drivers/i2c/busses/i2c-elektor.c: In function ‘pcf_isa_init’:
drivers/i2c/busses/i2c-elektor.c:153: error: implicit declaration of function ‘ioport_map’
drivers/i2c/busses/i2c-elektor.c:153: warning: assignment makes pointer from integer without a cast
drivers/i2c/busses/i2c-elektor.c: In function ‘elektor_probe’:
drivers/i2c/busses/i2c-elektor.c:287: error: implicit declaration of function ‘ioport_unmap’
Since commit 82ed223c26 ("iomap: make IOPORT/PCI
mapping functions conditional"), ioport_map() is only available on platforms
that set HAS_IOPORT.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch resolves two sets of race conditions.
Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the
first, as follows:
The bond_close() calls cancel_delayed_work() to cancel delayed works.
It, however, cannot cancel works that were already queued in workqueue.
The bond_open() initializes work->data, and proccess_one_work() refers
get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when
work->data has been initialized. Thus, a panic occurs.
He included a patch that converted the cancel_delayed_work calls
in bond_close to flush_delayed_work_sync, which eliminated the above
problem.
His patch is incorporated, at least in principle, into this
patch. In this patch, we use cancel_delayed_work_sync in place of
flush_delayed_work_sync, and also convert bond_uninit in addition to
bond_close.
This conversion to _sync, however, opens new races between
bond_close and three periodically executing workqueue functions:
bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon.
The race occurs because bond_close and bond_uninit are always
called with RTNL held, and these workqueue functions may acquire RTNL to
perform failover-related activities. If bond_close or bond_uninit is
waiting in cancel_delayed_work_sync, deadlock occurs.
These deadlocks are resolved by having the workqueue functions
acquire RTNL conditionally. If the rtnl_trylock() fails, the functions
reschedule and return immediately. For the cases that are attempting to
perform link failover, a delay of 1 is used; for the other cases, the
normal interval is used (as those activities are not as time critical).
Additionally, the bond_mii_monitor function now stores the delay
in a variable (mimicing the structure of activebackup_arp_mon).
Lastly, all of the above renders the kill_timers sentinel moot,
and therefore it has been removed.
Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Updated version number to 5.0.25
o Do not hold onto RESETTING_BIT for entire duration of LED/ beacon test.
Instead, just checking for RESETTING_BIT not set before sending config_led
command down to card.
o Take rtnl_lock instead of RESETTING_BIT for beacon test while sending
config_led command down to make sure interface cannot be brought up/ down.
o Allocate and free resources if interface is down before
sending the config_led command. This is to make sure config_led
command sending doesn't fail.
o Clear QLCNIC_LED_ENABLE bit if beacon/ LED test fails to start.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If promiscous mode setting fails, reset loopback mode setting in firmware.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fw reset path, we should consider any change in device state as an
ack from the other driver. When that happens, we don't have to wait for
an explicit ack.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko
Srinidhi KASAGAR
Antonio Ospite
David Daney
Axel Lin
Magnus Damm
Wolfram Sang
Masakazu Mokuno
Fabio Estevam
Mark Brown
Joe Perches
Peter Korsgaard
Jonghwan Choi
Éric Piel
Jonathan Cameron
Christoph Lameter
Linus Torvalds
NeilBrown
Jean Delvare
Jean Delvare
Harvey Yang
Geert Uytterhoeven
Jay Vosburgh
Sucheta Chakraborty
Sony Chacko
Sritej Velaga