This patch makes the rings a part of the q_vector directly instead of
indirectly. Specifically on x86 systems this helps to avoid any cache
set conflicts between the q_vector, the tx_rings, and the rx_rings as the
critical stride is 4K and in order to cross that boundary you would need to
have over 15 rings on a single q_vector.
In addition this allows for smarter allocations when Flow Director is
enabled. Previously Flow Director would set the irq_affinity hints based
on the CPU and was still using a node interleaving approach which on some
systems would end up with the two values mismatched. With the new approach
we can set the affinity for the irq_vector and use the CPU for that
affinity to determine the node value for the node and the rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a minor cleanup to address the unnecessary use of
napi_schedule_prep in ixgbe_intr and to also remove a blank line that is
not needed since it is separating a comment from the line it is explaining.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old code had several errors in how it was determining the vector
budget. In order to simplify things this patch updates the code so that it
will attempt to always allocated paired Rx/Tx vectors instead of attempting
to allocate individual vectors when the number of queues is less than the
number of CPUs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change corrects an issue in which Adaptive Interrupt Moderation was
not changing values due to the fact that we were performing an and
operation on the resultant value that was causing the value to never change
from the default 20K interrupts per second.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to address the fact that the tx_itr_setting was
dropping to 0 when no separate Tx vectors were provided. This had resulted
in the driver incorrectly configuring the Tx ring with a WTHRESH of 1 in
order to avoid Tx hangs even though that was not necessary. This change
makes it so that we instead take a look at the Tx ring's q_vector to
determine if the ring will have an ITR value less than 8us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves several frequently accessed items together into one cache
line in order to reduce cache misses in the hot-path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There isn't any need to clear the status bits in the descriptors due to the
fact that the eop_desc provides enough information for us to know
that we have cleaned to the last packet that the software has put on the
ring. The status bits are cleared as a part of putting the frame on the
ring so as long as we do not read the descriptor bit prior to reading the
value eop_desc we should be able to guarantee that we will not clean beyond
the end of the current data stream.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing dev_watchdog hangs on several drivers. I suspect this is due
to the __QUEUE_STATE_STACK_XOFF bit being set prior to a reset for link
change, and then not being cleared by netdev_tx_reset_queue. This change
corrects that.
In addition we were seeing dev_watchdog hangs on igb after running the
ethtool tests. We found this to be due to the fact that the ethtool test
runs the same logic as ndo_start_xmit, but we were never clearing the XOFF
flag since the loopback test in ethtool does not do byte queue accounting.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds support for byte queue limits (BQL).
Based on patch from Eric Dumazet for igb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
As noted by Ben Hutchings and David Miller, work limits for NAPI
should not be tied to interrupt moderation parameters. This
should be handled by NAPI, possibly through sysfs.
Neil Horman & Stephen Hemminger are working on a solution for
NAPI currently. In the meantime, remove this tie between
work limits and interrupt moderation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
A bug was introduced with the following patch:
Commmit bdbc063129
Author: Eric Dumazet <eric.dumazet@gmail.com>
igb: Add support for byte queue limits.
The ethtool offline tests will cause a perpetual link flap, this
is because the tests also need to account for byte queue limits (BQL).
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
v3: added previously removed sock_put() to the tun_release() callback, because
sk_release_kernel() doesn't drop the socket reference.
v2: sk_release_kernel() used for socket release. Dummy tun_release() is
required for sk_release_kernel() ---> sock_release() ---> sock->ops->release()
call.
TUN was designed to destroy it's socket on network namesapce shutdown. But this
will never happen for persistent device, because it's socket holds network
namespace.
This patch removes of holding network namespace by TUN socket and replaces it
by creating socket in init_net and then changing it's net it to desired one. On
shutdown socket is moved back to init_net prior to final put.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, allocation used queue statistics directly in its calcualtion.
This change causes these calculations to be summed into the statistics,
without being affected by them.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, if autoneg failed, ethtool would return the achieved autoneg.
This patch corrects this, causing ethtool to return the requested autoneg
capabilities even if autoneg fails.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, unless both interface and link were up, ethtool returned
the requested speed/duplex when asked for the interface's settings.
This change will now enable the driver to answer correctly (i.e.,
return unknown as its answer).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables the FW to make more accurate decisions regarding the
active functions.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've used the object's function id instead of using the
input's value. This is remedied, as in other flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we used a hard-coded value as paramater, instead of using the
input's value. This is now remedied, as in other flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These definitions are united into the header.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an ethernet driver for the LPC32xx ARM SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this feature, a Linux guest can now configure multiple vlans through
a single synthetic NIC on Win8 Hyper-V host.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limiting the memcpy to be the sizeof(struct rndis_message) can truncate
the message if there are Per-Packet-Info or Out-of-Band data.
In my earlier patch (commit 45326342), the unnecessary kmap_atomic and
kunmap_atomic surrounding this memcpy have been removed because the memory
in the receive buffer is always mapped. This memcpy is not necessary
either. To fix the bug, I removed the memcpy.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCoE statistics ids were distinguished from the L2's statistics ids.
However, not all of the change was committed. This causes a possible
collision of indices when FCoE is present.
This patch fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCB flags were updated using the flags' bit offsets instead of
the actual bits. This is now fixed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed endianess issue when passing arguments to FW.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pfc statistics were counted, the delta change from last count
was summed twice. This fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver defaults to 1M MTT segments, where each segment holds
8 MTT entries. This limits the total memory registered to 8M * PAGE_SIZE
which is 32GB with 4K pages. Since systems that have much more memory
are pretty common now (at least among systems with InfiniBand hardware),
this limit ends up getting hit in practice quite a bit.
Handle this by having the driver allocate at least enough MTT entries to
cover 2 * totalram pages.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the MTU for IB ports in the driver instead of using the firmware
default of 2KB (the driver defaults to 4KB). Allow for dynamic mtu
configuration through a new, per-port sysfs entry.
Since there's a dependency between the port MTU and the max number of
HW VLs the port can support, apply a mim/max approach, using a loop
that goes down from the highest possible number of VLs to the lowest,
using the firmware return status to know whether the requested number
of VLs is possible with a given MTU.
For now, as with the dynamic link type change / VPI support, the sysfs
entry to change the mtu is exposed only when NOT running in SR-IOV
mode. To allow changing the MTU for the master in SR-IOV mode,
primary-function-initiated FLR (Function Level Reset) needs to be
implemented.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Print an error message when a thermal error async event is reported by the HW.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Dotan Barak <dotanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 22c8bff6fa ("mlx4_core: Exported functions can't be static")
fixed most of this up, but forgot about mlx4_is_slave_active(). Fix
this one too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
mvm_ucode is true when mvm TLVs arive.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change iwl_fw struct to hold an array of fw_img instead of
three separated instances.
Change fw_img to hold an array of fw_desc instead of two
separate descriptors for instructions and data.
Change load_given_ucode, load_section, verification functions
etc. to support this structure.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New TLVs for ucode sections that are not known as
instruction or data.
New TLVs for phy-configuration and default calibrations.
Add default calib and phy config fields to iwl_fw.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed iwl_firmware_pieces structure to support an array of
separate images, and an array of sections for each image.
In fw_sec and fw_desc structures, added a field for
offset from the HW address, to support 16.0 uCode that
provides an offset instead of any other data about the section.
This field is filled with default values when parsing instruction
or data section.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove IWL_UCODE_NONE from enum iwl_ucode_type which,
by being the default value in 0-initialized memory,
implicitly allowed us to track whether any uCode had
ever been loaded successfully (which would have been
the INIT uCode) and instead explicitly track whether
or not INIT uCode has been run.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Printing the SRAM and similar testmode operations could
be triggered when no uCode is loaded; prevent those
invalid operations by tracking whether uCode is loaded.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This wait queue really belongs to the transport
layer, as it is used for sending synchronous
commands to the HW.
However, only op_mode knows about errors and
exceptional conditions, so make this queue
accessible by the op_mode.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looking at logs, I see that we did get the bad
state message a few times for some reason, but
it doesn't indicate why or where it came from,
so make it a warning in order to identify it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi ran into [1] the SEQ_RX_FRAME workaround
warning with a statistics notification, this means we
can't just remove it as we'd hoped.
Abstract it out so that the higher layer can configure
this as a kind of "filter" in the transport.
[1] http://mid.gmane.org/CAD2nsn1_DzbRHuSbS_1rFNzuux_9pW1-pABEasQ01_y7-ndO5w@mail.gmail.com
Reported-by: Mohammed Shafi <shafi.wireless@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tracing is much better for this, so
remove the hex printk debug for the
TX command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check for PS_WAIT_FOR_TX_ACK was inverted, the hardware should only go
to full sleep if no tx is pending.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mactime was being overwritten by the function ath9k_rx_skb_preprocess. Fixed by
memsetting rx_status in ath_rx_tasklet.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The proper place to configure bss info is at assoc notification. So that
ath9k continues to work if the supirous bssid notification will be
removed in future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci is suffering from beacon skew in AP mode. Some powersaving
clients (like VOIP phones) are getting into trouble after some time
when the beacon skew is getting too big.
The ralink legacy drivers contain a function that indicates that the
beacon timer is off by 1us per tbtt. And this function works around
that by reducing the beacon interval for every 64th beacon transmission
by 64us (the smallest possible value). Do the same in rt2800pci.
This allows proper powersaving when rt2800pci is used in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tested in AR9462 Rev:2, both hardware capability flag are set
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2200 driver does not use these defines, it uses geo struct instead.
Therefore remove them from its header.
Note: we keep them in the ipw2100 driver's header, because the driver
still uses them.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On systems with multiple NICs, it's nice to know which
one is producing warnings. Here is an example of the
new ouput:
ath: wiphy0: Failed to stop TX DMA, queues=0x005!
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "mac80211_hwsim: Add tsf to beacons, probe responses and radiotap
header" was setting the mactime on wrong hwsim radio. This patch fixes it.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Is possible that we stop queue and then do not wake up it again,
especially when packets are transmitted fast. That can be easily
reproduced with modified tx queue entry_num to some small value e.g. 16.
If mac80211 already hold local->queue_stop_reason_lock, then we can wait
on that lock in both rt2x00queue_pause_queue() and
rt2x00queue_unpause_queue(). After drooping ->queue_stop_reason_lock
is possible that __ieee80211_wake_queue() will be performed before
__ieee80211_stop_queue(), hence we stop queue and newer wake up it
again.
Another race condition is possible when between rt2x00queue_threshold()
check and rt2x00queue_pause_queue() we will process all pending tx
buffers on different cpu. This might happen if for example interrupt
will be triggered on cpu performing rt2x00mac_tx().
To prevent race conditions serialize pause/unpause by queue->tx_lock.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On il3945_down procedure we free tx queue data and nullify il->txq
pointer. After that we drop mutex and then cancel delayed works. There
is possibility, that after drooping mutex and before the cancel, some
delayed work will start and crash while trying to send commands to
the device. For example, here is reported crash in
il3945_bg_reg_txpower_periodic():
https://bugzilla.kernel.org/show_bug.cgi?id=42766#c10
Patch fix problem by adding il->txq check on works that send commands,
hence utilize tx queue.
Reported-by: Clemens Eisserer <linuxhippy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Portion of the commit id 080eec4fb4 ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.
kvalo: more details to the commit log
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip.
Added USB id to find correct driver for AX88178 1000 Ethernet adapter.
Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has been tested on a machine with the Realtek
RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05).
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq. Without this
property, free_irq does nothing.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not need this leftover of the ISA drivers era.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
This driver is specific to the PowerPC legcay iSeries platform which is
being removed.
Cc: David Miller <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Supports EG20T ptp clock in the driver
Changes e-mail address.
Adds number.
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the Pantech UML290 and all non-QDL Gobi device IDs from the
qcserial driver now that we have support for shared net/QMI USB
interfaces. Most of these are not yet tested with this driver, but
should be mostly identical to tested devices, except for device IDs.
Gobi devices provide several different interfaces (serial/net/other)
using the exact same class, subclass and protocol values. This driver
will only support the net/QMI function while there are other drivers
supporting other device functions. The net/QMI interface number may
also differ from device to device. It has been noted that all the
other interfaces have additional functional descriptors, so we use that
to detect the interface supported by this driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new cdc-wdm subdriver interface to create a device management
device even for USB devices having a single combined QMI/wwan USB
interface with three endpoints (int, bulk in, bulk out) instead of
separate data and control interfaces.
Some Huawei devices can be switched to a single interface mode for
use with other operating systems than Linux. This adds support
for these devices when they run in such non-Linux modes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces. The Huawei E392/E398 are examples of such devices.
These typically cannot be fully configured using AT commands
over a serial interface. It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.
The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function. This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.
Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver. To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.
You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BIg portion of "iwlwifi: remove max_txq_num from hw_params" was
missing during merge, here is the fix for it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: move command queue number out of the iwl_shared struct
move the cmd_queue out of iwl_shared struct, but for some reason the
patch is half done and fail compile
Here is the fix
John, could you apply this patch to wireless-next to address the issue
Thanks
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in iwlwifi: move setting up fw parameters
Meenakshi moved code up to configure the transport layer, but this
code read the sku before it was set (from the EEPROM). This killed
P2P.
Only the ucode_flags are needed to configure the transport layer, not
the sku which _must_ be set after the EEPROM is read.
We need to reconfigure the transport in case the EEPROM disabled PAN
support. This is not the nicest thing to do, but we have no choice.
Document that we are allowed to configure the transport several times
before start_fw, but not after.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The command queue number is required by the transport
layer, but it can be determined only by the op mode.
Move this parameter to the dvm op mode, and configure
the transport layer using an API.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <olaf@aepfle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Again, no need to do that from the pci probe function.
Hmm, I noticed this driver is marked as BROKEN. Won't touch it more,
it has to be converted to dynamic tty driver allocation first.
Perhaps it is time to move it to staging?
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are in .bss which is initialized to zeros when the module is
loaded/kernel booted.
What a strange way to do the initialization once in the pci probe
routine...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In recent commit "mwifiex: correct bitrates advertised..", we have
removed 22Mbps and 72Mbps bitrates from supported bitrate array.
It means number of bitrates has reduced from 14 to 12.
Initialize ".n_bitrates" to array size instead of hardcoding it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I missed a couple of status bits in my refactoring changes. This
fixes the ones I missed.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the mac80211 deauth sequence changes, the
station is deleted before the device is set
unassociated. This can cause the device to get
confused as it expects the station to be there
while the associated bit is set.
To fix this, do not delete the AP station from
the device when mac80211 asks for deletion,
instead just mark it as unused and rely on the
unassociated RXON to drop it from the station
database in the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not needed anywhere but during init.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only reason we ever stop/wake queues at
the transport level is now that they become
full (or non-full), so the messages aren't
useful any more -- remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Continue splitting the status bits between transport and op_mode.
All but a few are separated.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gather parameters required to configure the
transport layer before invoking the transport
configuration API.
Change-Id: I5b39da284af6d9b5432a08911b4e1173a4d7207d
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce the iwl_trans_config struct which contains
state variables that only the op mode can determine,
but which the transport layer needs to know.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a few missing occurences when we get PASSIVE_NO_RX
notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The shared status bits are a mixture of transport and op mode bits.
Some are used just by one or the other, some are shared. Begin the
de-tangling of these bits.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a Kconfig symbol to enable MFP for testing even
if the firmware file doesn't advertise it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of iwl_rx_packet doesn't include the
dword for the length itself, so add it manually.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added a testmode command which tells iwl_rx_dispatch
to send the RX both as a notification to nl80211 and
with the registered RX handlers.
This is used for monitoring RX from userspace while preserving
the regular flows in the driver.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device is disabled by rfkill switch, do not enable all interrupts,
but only CSR_INT_BIT_RF_KILL to receive rfkill state change. Unblocking
other interrupts might cause problems, since driver can not be prepared
for receive them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_poll_direct_bit() return negative error value on timeout,
positive values do not indicate an error.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That change will save us some CPU cycles at run time. Having port-based
I/O seems to be not possible for PCIe devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wmb(), rmb() are not needed when writel(), readl() are used as
accessors for MMIO. We use them indirectly via iowrite32(),
ioread32().
What is needed mmiowb(), for synchronizing writes coming from
different CPUs on PCIe bridge (see in patch comments). This
fortunately is not needed on x86, where mmiowb() is just
defined as compiler barrier. As iwlwifi devices are most likely
not used on anything other than x86, this is not so important
fix.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before we write to the device registers always check if
iwl_grap_nic_access() was successful.
On the way change return type of grab_nic_access() to bool, and add
likely()/unlikely() statement.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print dump stack when the device is not responding. This should give
some more clue about the reason of failure. Also change the message we
print, since "MAC in deep sleep" is kinda confusing.
On the way add unlikely(), as fail to gain NIC access is hmm ...
unlikely.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "iwlwifi: consolidate the start_device flow"
the code flow changed and the firmware is now
loaded by the transport layer, but the change
unfortunately lost error checking -- restore.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sensitivity parameters are never modified, so they
should be const. Also remove the unused max_nrg_cck
value to save some space.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to carry around the function
pointer when a boolean indicating that the
EEPROM stores enhanced TX power information
is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware parameters will be shared, so
move the definitions into the shared
header file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have operations for
these as they simply depend on whether
the device has built-in bluetooth, so
just duplicate the information already
there (whether bt_params is present or
not).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least as long as it is called from the reclaim
flow (iwlagn_check_ratid_empty) it must be atomic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PASSIVE_NO_RX workaround currently crosses
through the op_mode and transport layers, which
is a bit odd. This also isn't necessary, if the
transport simply reports when queues are full
(or no longer full) the op_mode can keep track
of this state, and report to mac80211 only what
*it* thinks is appropriate. What is appropriate
can then be based on whether queues should be
stopped to wait for RX or not.
This significantly simplifies the transport API,
it no longer needs to expose anything to stop a
queue, nor to wake "any" queue, this can all be
handled in the upper layer completely.
Also simplify the handling to not be dependent
on the context, that makes little sense as the
queues are shared and both contexts have to be
on the same channel anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's not much point in passing priv and
hw pointers since they can be derived from
each other, and the function doesn't use
the hw pointer anyway. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dump functions never access the incoming
attributes, so don't pass them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function never uses the priv argument as it
only fills in the passed data, so remove the
argument.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's only one user, so the function
can be moved into the correct file. It
also loses an argument along the way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function never uses its conf argument,
so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function has two arguments it never uses,
remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track freed FW blocks during Tx. If no blocks were freed during a
predefined timeout, initiate a HW recovery. This helps in situations
when the FW watchdog fails.
Don't trigger recovery during activities that can temporarily stop
Tx. This includes:
- scanning
- buffering packets for sleeping stations (AP role)
- ROC on any role
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)
defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.
Cc: stable@kernel.org
Reported-by: AnÃbal Almeida Pinto <anibal.pinto@efacec.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
zero mac address is a valid address for VIC dynamic vnic and sriov Vf's.
Fix the check in enic_set_vf_mac appropriately
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.
Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop. The
intent was to set the zero bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 239c562c94 (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add AD-HOC support to the rtl8187 based on the rtl8180 source
Signed-off-by: Attila Fazekas <turul64@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is only used in iwl-scan.c, so
if we move it up a little in the file it can
be made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do some cleanups here:
* remove an unused prototype
* remove some unused constants
* clean up includes
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's only needed in a few places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to have a special config variable
for the PA type, we can just use the
additional NIC config function to config
the hardware correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally nothing needs to access priv
from shared any more, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nic_config sets uCode dependent register
bits, so it must be virtual in the op_mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base packet structure will (hopefully) be
the same for all transports, but what is in it
differs. Remove the union of all the possible
contents and move the packet itself into the
transport header file. This requires changing
all users of the union to just use pkt->data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if the variable might also be used by other
transports, there's no need for anything outside
of the transport itself to access it, so move it
into the private area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All variables related to uCode loading (the
waitqueue and done indication) should be in
the PCI-E transport's private data as this
is transport specific. Move them there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transport doesn't really need to know as
we can enforce it in the command wrapper.
Move the ucode_owner variable into priv and
do all enforcing there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be sharable, but needs to live in the
op_mode as it is dependent on command processing.
Make a library out of the notification wait code.
Since I wrote all of the code originally and only
Intel employees changed it, we can also relicense
it to dual BSD/GPL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "iwlwifi: consolidate the start_device flow"
Emmanuel added the return if the fw isn't there
but forgot to take into account that the struct
for notification wait needs to be added only
after the check -- fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW configuration settings base_params, ht_params
and bt_params all should be const, make it so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware config ht_params shouldn't be modified,
so copy the use_rts_for_aggregation parameter into
hw_params and use/modify it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the version that can be modified, the
config params should be read-only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base_params shouldn't be writable, so keep
a copy of this in priv that can be modified.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used directly from the config now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a hardware parameter, so it shouldn't
be configurable by the user. Users can disable
aggregation (which is the only thing affected)
with 11n_disable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transport doesn't need to include iwl-core.h any more.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the command queue is full, the transport
will return -ENOSPC, but the reaction to that
depends on the op_mode. Virtualize that, the
DVM op_mode checks for CT-kill and restarts
the hardware otherwise.
We may be able to get rid of this callback by
putting the behaviour check into the wrapper
but that needs more careful evaluation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tracing used the priv pointer as an identifier,
which has the problem that we don't have it in
all code, and also some people say no pointers
should be "leaked" to userspace.
Use the device name instead, it is more useful
anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are only used in the DVM op_mode.
Also move the rfkill debug macros that
depend on them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to copy shadow_reg_enable into
hw_params since it is a pure hardware parameter
that will never change, we can access it from
the config directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As iwl_prepare_card_hw() is idempotent (and
many cards support AMT anyway) there's no
point in calling iwl_prepare_card_hw() only
for AMT capable devices -- call it always
and simplify the code that way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That name better reflects the contents
of the file and the fact that it isn't
related to iwl-ucode.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transport layer should only check the
hardware RF kill status, not impose any
policy or reaction based on it, so move
that out of it into the op_mode.
For now keep the restriction on loading
firmware, that will have to be removed
later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the mutex no longer needs to be
shared, so move it into iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fact that the mutex must be held is an
implementation detail of DVM, but something
has to ensure that no two synchronous cmds
are submitted concurrently. Move the lockdep
assertion into the DVM-specific code, but
also make the transport abort if there are
two concurrently commands.
The assertion is much more useful though as
the transport check can only catch it when
it actually happens, while the assertion
makes sure it can't possibly happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we cannot send any commands when the
uCode is in RF or CT kill, but that will not be
true for all new uCode versions, so we need to
move the check into the uCode specific code.
Also remove the duplicate rfkill check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrappers to send commands from the DVM
op-mode (which essentially consists of the
current driver). This will allow us to move
specific sanity checks there.
Also, this removes iwl_trans_send_cmd_pdu()
since that can now be taken care of in the
DVM-specific wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file was recently introduced, but then
directly abused -- it contained private data
that shouldn't have been used by anything
but the implementation of firmware requests
and some very core code. Now that it is no
longer accessed by any code but the code in
iwl-drv.c, we can dissolve it.
Also rename the iwl_nic struct to iwl_drv to
better reflect where and how it is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Through the driver, struct iwl_fw will
store the firmware. Split this out into
a separate file, iwl-fw.h, and make all
other code use it. To do this, also move
the log pointers into it, and remove the
knowledge of "nic" from everything.
Now the op_mode has a fw pointer, and
(unfortunately) for now the shared data
also needs to keep one for the transport
to access dump the error log -- I think
that will move later.
Since I wanted to constify the firmware
pointers, some more changes were needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uCode loading belongs to the op_mode, as it
is dependent on various things there and the
commands sent during it are specific to it.
Move the prototypes to iwl-agn.h to indicate
this. To make this possible, also move all
the calibration handling (which is op_mode
dependent after all).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On A-MPDU frames, the hardware only reports valid signal strength data for
the last subframe. The driver also mangled rx_stats->rs_rssi using the
ATH_EP_RND macro in a way that may make sense for ANI, but definitely
not for reporting to mac80211.
This patch changes the code to calculate the signal strength from the rssi
directly instead of taking the average value, and flag everything but
the last subframe in an A-MPDU to tell mac80211 to ignore the signal strength
entirely, fixing signal strength fluctuation issues reported by various
users.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process rx status directly instead of separating the completion test from
the actual rx status processing.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way this is implemented (simply storing the last value) is absolutely
worthless for debugging anything, and the same information is also available
through the MAC sample feature, so there's no point in keeping this around.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They're more expensive than some of the other debug options and only used
in very rare situations, so it sometimes makes sense to disable them while
leaving in debugfs support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cold reset is more reliable for getting the hardware out of some specific
stuck states.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Found by checkpatch:
drivers/net/wireless/ath/ath6kl/init.c:78: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/init.c:397: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/init.c:407: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:189: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:704: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:2452: WARNING: line over 80 characters
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Also fixes quite a few checkpatch warnings like this:
ath6kl/hif.h:226: CHECK: spinlock_t definition without comment
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error handling in ath6kl_target_config_wlan_params() was just weird,
fix that. This also fixes some of the open parenthesis alignment issues
reported by checkpatch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are few 32 bit reads from the host interest area. Add
ath6kl_bmi_read_hi32() to make it easier to do that. As code is cleaner
this also fixes few checkpatch warnings.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We have a lot of 32 bit writes to the host interest area and the code
doing that is ugly. Clean that up by adding ath6kl_bmi_write_hi32().
This also fixes few checkpatch warnings.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found by checkpatch:
drivers/net/wireless/ath/ath6kl/cfg80211.c:1295: CHECK: multiple assignments should be avoided
drivers/net/wireless/ath/ath6kl/cfg80211.c:3000: CHECK: multiple assignments should be avoided
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All found by checkpatch:
ath6kl/wmi.c:1036: CHECK: Logical continuations should be on the previous line
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the issues which checkpatch found and were easy to fix. Especially
callers of ath6kl_bmi_write() are tricky and that needs to be fixed
separately.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
reported by checkpatch:
ath6kl/core.h:748: ERROR: "foo * bar" should be "foo *bar"
ath6kl/core.h:751: ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That patch fixes some bad usage of two little-endian variables, which lead to
some warning/error when building the peak_usb driver.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* In order to save the target power in WOW suspend state,
configure the best optimal values for the below parameters,
- listen interval.
- beacon miss interval.
- scan parameters.
Default values for above attributes are reverted in
wow resume operation.
* The default listen interval is set before the host issue
connect request.
* New function is added to configure beacon miss count.
kvalo: minor changes to fix open parenthesis alignment
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware has the option to support the listen interval
per vif specific. Fix this.
Listen interval can be set by the TUs or by the number
of beacons. Current code enables the user to configure
the listen interval in the unit of 'number of beacons'
using debugfs entry "listen_interval". Going forward,
we need to alter the listen interval in the unit of TUs
to get good power numbers while going to WOW suspend/resume.
Allowing the user to change the listen interval in
the unit of "number of beacons" in debugfs and changing
listen interval in wow suspend/resume in the unit of
time (TUs) would lead us to confuse.
This patch make sures the listen interval is changed only
in the unit of time (TUs).
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Below two scenarios are taken care in this patch which helped
to fix the firmware crash during wow suspend/resume.
* TX operation (ctrl tx and data tx) has to be controlled based
on suspend state. i.e, with respect to WOW mode, control packets
are allowed to send from the host until the suspend state goes
ATH6KL_STATE_WOW and the data packets are allowed until WOW
suspend operation starts.
* Similarly, wow resume is NOT allowed if WOW suspend is in progress.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It gives flexibility to the user to define suspend policy
when the suspend mode is set to WOW and the device is in
disconnected state at the time of suspend.
New module parameter wow_mode is added to get the choice
from the user. This parameter is valid only if the module
parameter suspend_mode is set to WOW.
To force WOW in connected state and cut power
in disconnected state:
suspend_mode=0x3 wow_mode=0x1
To force WOW in connected state and deep sleep
in disconnected state (this is also the default wow_mode):
suspend_mode=0x3 wow_mode=0x2
If there is no value specified to wow_mode during insmod,
deep sleep mode will be tried in the disconnected state.
kvalo: clarified commit log
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While doing the work for commit a6f7feae6d ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b7817 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).
This patch reverts commit 97285b7817 and removes the check for
extended caps from the mlx4_ib driver port query flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch includes:
Configure EMAC PHY clock source (clock from PHY or internal clock).
Do not advertise PHY half duplex capability as APM821XX EMAC does not support half duplex mode.
Add changes to support configuring jumbo frame for APM821XX EMAC.
[ Fix coding style -DaveM ]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default MTU for CAIF HSI was wrongly set to 15 * 4092 bytes.
The patch sets default MTU size to 4096.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing sparse warnings, the 2 functions are only used in same
file. Defining them as static and not exporting them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing functions that are no longer in use, but still exist
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_PORT functions are implemented in port.c, which is part
of mlx4_core, these functions are exported. The functions are in use by
the mlx4_en module (were originally part of mlx4_en).
Their declaration remained in mlx4_en module, moving the declaration to the right location.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac should be written as __be64 the gid. The warning was because
we changed the mac parameter, which is u64, by writing result of cpu_to_be64
into it. Fixing by using new variable of type __be64.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keys used for the hardware RSS topelitz hash are of type __be32
where the values provided by the driver are from array of u32,
this triggered sparse warning on incorrect type in assignment as of different base types.
Since these values are picked randomly,
the fix is to transform the key to __be32 by executing cpu_to_be_32()
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blue flame buffer is defined to be of type void __iomem *
but was passed to mlx4_bf_copy which gets unsigned long * .
This triggered sparse warning on different address spaces,
fix that by changing mlx4_bf_copy first param to be of type void __iomem * .
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings on incompatibility between the endianess of the ctrl_flags
field of struct mlx4_en_priv to the srcrb_flags field of struct
mlx4_wqe_ctrl_seg by changing the former to be __be32 instead of u32.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Localized the pdev->dev, and using dma_map instead of pci_map
There are multiple map/unmap operations on data path,
optimizing those by saving redundant pointer access.
Those places were identified as hot-spots when running kernel profiling
during some benchmarks.
The fixes had most impact when testing packet rate with small packets,
reducing several % from CPU load, and in some case being the difference
between reaching wire speed or being CPU bound.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silence the following warning:
"warn: returning -1 instead of -ENOMEM is sloppy".
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other Atheros drivers run the AGC gain calibration and DC offset
calibration only after reset. Running them periodically has caused stability
issues on some (primarily AR2315/2413/5413/5414 based) devices, leading to
messages such as:
ath5k phy0: gain calibration timeout (2462MHz)
ath5k phy0: calibration of channel 11 failed
Related bug reports:
https://dev.openwrt.org/ticket/10574https://bugzilla.redhat.com/show_bug.cgi?id=795141
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some calibration types interfere with tx activity, but the queue stop does
not prevent that. In fact, some calibration types need tx activity to properly
function, so stopping the queues for them is counterproductive.
In some tests this patch has been shown to improve stability, especially in
AP or ad-hoc mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Generate a tsf from internal kernel clock. Prepare the path for having
different tsf offsets on each phy. This will be useful for testing
mesh synchronization algorithms.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Duyck
Jeff Kirsher
Stanislav Kinsbursky
Dmitry Kravkov
Yuval Mintz
stigge@antcom.de
Haiyang Zhang
Ariel Elior
Roland Dreier
Or Gerlitz
Jack Morgenstein
David Spinadel
Meenakshi Venkataraman
Johannes Berg
Felix Fietkau
Ashok Nagarajan
Rajkumar Manoharan
Helmut Schaa
Mohammed Shafi Shajakhan
Stanislav Yakovlev
Ben Greear
Sujith Manoharan
Stanislaw Gruszka
Greg Kroah-Hartman
Aarthi Thiruvengadam
Joerg Neikes
Richard Cochran
Julia Lawall
David S. Miller
Francois Romieu
Stephen Rothwell
Takahiroi Shimizu
Bjørn Mork
John W. Linville
Wey-Yi Guy
Emmanuel Grumbach
Jiri Slaby
Amitkumar Karwar
Don Fry
Amit Beka
Luciano Coelho
Arik Nemtsov
Sebastian Siewior
Roopa Prabhu
Dan Carpenter
Eric Dumazet
Attila Fazekas
Kalle Valo
Stephane Grosjean
Raja Mani
Duc Dang
Sjur Brændeland
Vipul Pandya
Yevgeny Petrilin
Santosh Nayak
Javier Cardona