commit 8dad0386b9 upstream.
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40ddbf5069 upstream.
commit 65b97cf6b8 introduced in v3.7 caused a regression
by using a reversed CS_MASK thus causing omap_calculate_ecc to
always fail. As the NAND base driver never checks for .calculate()'s
return value, the zeroed ECC values are used as is without showing
any error to the user. However, this won't work and the NAND device
won't be guarded by any error code.
Fix the issue by using the correct mask.
Code was tested on omap3beagle using the following procedure
- flash the primary bootloader (MLO) from the kernel to the first
NAND partition using nandwrite.
- boot the board from NAND. This utilizes OMAP ROM loader that
relies on 1-bit Hamming code ECC.
Fixes: 65b97cf6b8 (mtd: nand: omap2: handle nand on gpmc)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7e460624f upstream.
The pxa3xx_nand driver currently uses __raw_writel() and __raw_readl()
to access I/O registers. However, those functions do not do any
endianness swapping, which means that they won't work when the CPU
runs in big-endian but the I/O registers are little endian, which is
the common situation for ARM systems running big endian.
Since __raw_writel() and __raw_readl() do not include any memory
barriers and the pxa3xx_nand driver can only be compiled for ARM
platforms, the closest I/o accessors functions that do endianess
swapping are writel_relaxed() and readl_relaxed().
This patch has been verified to work on Armada XP GP: without the
patch, the NAND is not detected when the kernel runs big endian while
it is properly detected when the kernel runs little endian. With the
patch applied, the NAND is properly detected in both situations
(little and big endian).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f306e8c3b6 upstream.
fixes: commit 62116e5171
mtd: nand: omap2: Support for hardware BCH error correction.
In omap_elm_correct_data(), if bitflip_count in an erased-page is within the
correctable limit (< ecc.strength), then it is not indicated back to the caller
ecc->read_page().
This mis-guides upper layers like MTD and UBIFS layer to assume erased-page as
perfectly clean and use it for writing even if actual bitflip_count was
dangerously high (bitflip_count > mtd->bitflip_threshold).
This patch fixes this above issue, by returning 'stats' to caller
ecc->read_page() under all scenarios.
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f034d87def upstream.
As subpage write is enabled by default for all drivers, nand_write_subpage_hwecc
causes a crash if the driver did not register ecc->hwctl or ecc->calculate.
This behavior was introduced in
commit 837a6ba4f3
"mtd: nand: subpage write support for hardware based ECC schemes".
This fixes a crash by emulating subpage write support by padding sub-page data
with 0xff on either sides to make it full page compatible.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c69dbbf333 upstream.
Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR"
which is NULL and not a valid register.
Fixes: 8bff82cbc3 ('mtd: add nand support for w90p910 (v2)')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86e4bbc766 upstream.
Passing a name to request_mem_region() isn't optional and can't just
be NULL. Passing NULL causes a NULL ptr deref later in the boot
process.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90445ff624 upstream.
Crash detected on sam5d35 and its pmecc nand ecc controller.
The problem was a call to chip->ecc.hwctl from nand_write_subpage_hwecc
(nand_base.c) when we write a sub page.
chip->ecc.hwctl function is not set when we are using PMECC controller.
As a workaround, set NAND_NO_SUBPAGE_WRITE for PMECC controller in
order to disable sub page access in nand_write_page.
Signed-off-by: Herve Codina <Herve.CODINA@celad.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch excludes reserved-marker byte-position from oobfree->length
calculation. Thus all bytes from oobfree->offset till end of OOB are free.
CC: <stable@vger.kernel.org> # 3.13.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
1) In current implementation, ecclayout->oobfree->offset is calculated with
respect to ecclayout->eccpos[0] which is incorrect because ECC bytes may not
be stored contiguously in OOB.
So, this patch calculates ecclayout->oobfree->offset with respect to last
ECC byte-position 'eccpos[ecclayout->eccbytes-1]'.
2) ECC layout of some ecc-schemes expects reserved-markers at specific eccpos[]
which should not be over-written by any file-system metadata.
So this patch aligns oobfree->offset taking into account of such markers.
CC: <stable@vger.kernel.org> # 3.13.x+
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
The buffer pointer passed from the upper layer may points to
a buffer in the stack or a buffer allocated by vmalloc, and etc..
This patch adds more sanity check to this buffer.
After this patch, if we meet a buffer which is allocated by vmalloc or
a buffer in the stack, we will use our own DMA buffer @data_buffer_dma
to do the DMA operations. If the buffer is not the cases above, we will
map it for DMA operations directly.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The @data_buffer_dma buffer is used for non ECC read/write.
Currently, the length of the buffer is PAGE_SIZE, but the NAND chip may
has 8K page or 16K page. So we have to extend it for the large page NAND
chips.
The gpmi_alloc_dma_buffer will be called twice. The first time is to
allocate a temporary buffer for scanning the NAND chip; The second time
is to allocate a buffer to store the real page content.
This patch allocates a buffer of PAGE_SIZE size for scanning the NAND
chip when gpmi_alloc_dma_buffer is called the first time, and allocates a
buffer of the real NAND page size for the second time gpmi_alloc_dma_buffer
is called.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
plat/regs-nand.h is used only by S3C2410 nand driver. Since there
are no other users, merge this file into the driver code to remove
platform dependency. While at it also remove unused macros.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource(). And move those two call together
to make the connection between them more clear.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the Intel manufacturer Id.
Tested with Intel JS29F32G08ACMD1(4096 + 224) which is ONFI 2.0 compliant
nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the manufactor ID for SanDisk.
Make preparation for SanDisk SDTNRGAMA-008G.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Assume that:
tmp = ((extid >> 2) & 0x04) | (extid & 0x03));
From the K9LCG08U0B's datasheet, we know that:
the oob size is 640 when tmp is 6;
the oob size is 1024 when tmp is 7;
Signed-off-by: Huang Shijie <b32955@freescale.com>
[Brian: fixed compile issue]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds support for devices with 2048B page sizes and
4-bit ECC strength requirements. This is achieved by enabling the BCH
ECC engine, which provides a higher strength: 16-bit over 2048 bytes.
Additionally, add a proper ECC layout to model the controller's view
of the device (where 'U' means unused and 'B' is the bad block marker):
----------------------------------------------------
| 2048B data | B | B | 30B spare | 30B ECC | U | U |
----------------------------------------------------
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
[Brian: updated with Ezequiel's patch description]
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to the Open NAND Flash Interface Specification (ONFI) Revision
3.1 "Parameters are always transferred on the lower 8-bits of the data
bus." for the Get Features and Set Features commands.
So using read_buf and write_buf is wrong for 16-bit wide nand chips as
they use I/O[15:0]. The Get Features command is easily fixed using 4
times the read_byte callback. For Set Features implement a new
overwritable callback "write_byte". Still I expect the default to work
just fine for all controllers and making it overwriteable was just done
for symmetry.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Brian: fixed warning]
Tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Micron provides READ RETRY support via the ONFI vendor-specific
parameter block (to indicate how many read-retry modes are available)
and the ONFI {GET,SET}_FEATURES commands with a vendor-specific feature
address (to support reading/switching the current read-retry mode).
The recommended sequence is as follows:
1. Perform PAGE_READ operation
2. If no ECC error, we are done
3. Run SET_FEATURES with feature address 89h, mode 1
4. Retry PAGE_READ operation
5. If ECC error and there are remaining supported modes, increment the
mode and return to step 3. Otherwise, this is a true ECC error.
6. Run SET_FEATURES with feature address 89h, mode 0, to return to the
default state.
This patch implements the chip->setup_read_retry() callback for
Micron and fills in the chip->read_retries.
Tested on Micron MT29F32G08CBADA, which supports 8 read-retry modes.
The Micron vendor-specific table was checked against the datasheets for
the following Micron NAND:
Needs retry Cell-type Part number Vendor revision Byte 180
----------- --------- ---------------- --------------- ------------
No SLC MT29F16G08ABABA 1 Reserved (0)
No MLC MT29F32G08CBABA 1 Reserved (0)
No SLC MT29F1G08AACWP 1 0
Yes MLC MT29F32G08CBADA 1 08h
Yes MLC MT29F64G08CBABA 2 08h
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Modern MLC (and even SLC?) NAND can experience a large number of
bitflips (beyond the recommended correctability capacity) due to drifts
in the voltage threshold (Vt). These bitflips can cause ECC errors to
occur well within the expected lifetime of the flash. To account for
this, some manufacturers provide a mechanism for shifting the Vt
threshold after a corrupted read.
The generic pattern seems to be that a particular flash has N read retry
modes (where N = 0, traditionally), and after an ECC failure, the host
should reconfigure the flash to use the next available mode, then retry
the read operation. This process repeats until all bitfips can be
corrected or until the host has tried all available retry modes.
This patch adds the infrastructure support for a
vendor-specific/flash-specific callback, used for setting the read-retry
mode (i.e., voltage threshold).
For now, this patch always returns the flash to mode 0 (the default
mode) after a successful read-retry, according to the flowchart found in
Micron's datasheets. This may need to change in the future if it is
determined that eventually, mode 0 is insufficient for the majority of
the flash cells (and so for performance reasons, we should leave the
flash in mode 1, 2, etc.).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
ECC failures can be tracked at the page level, not the do_read_ops level
(i.e., a potentially multi-page transaction).
This helps prepare for READ RETRY support.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Now that the driver can support the Armada 370/XP SoC NAND controller,
add the devicetree compatible string, enabling its use.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
after device tree based clock lookup became available, the NAND
flash driver need no longer use the previous global "nfc_clk" name,
but should use the "ipg" clock name specific to the OF node
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch kills the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following
way:
1.) change the @buf field of nand_buf{} from an array to a pointer.
also remove the DENALI_BUF_SIZE macro.
2.) Before we call the nand_scan_ident, we allocate a temporary buffer
whose size is PAGE_SIZE.
3.) After we finish the nand_scan_ident, we have already getten the
page size and oob size. We will allocate the right buffer size
again.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We kill the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following way:
1.) Before we call the nand_scan_ident, we allocate a temporary buffer
whose size is PAGE_SIZE.
2.) After we finish the nand_scan_ident, we have already getten the
page size and oob size. We will allocate the right buffer size
again.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd.name is assigned to IFC NAND physical address. Assignment type is u32.
It is not providing correct physical address of IFC NAND.
Update assignment type to u64.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch assigned the type->name to mtd->name when mtd->name is
NULL in function "find_full_id_nand".
mtd->name is NULL may cause some problem.
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The kernel already has this information, and individual drivers
shouldn't duplicate that. This also eliminates the use of __DATE__ and
__TIME__, which make the build non-deterministic.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The omap_{read,write}_buf{8,16}() functions are identical to the default
nand_base versions. Just let nand_base assign them in the
NAND_OMAP_POLLED case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Pekon Gupta <pekon@ti.com>
We shouldn't try to allocate a resource until we're sure the
of_property_read_u64() call didn't fail. This is especially important if
we use this code for both CONFIG_OF and !CONFIG_OF builds, since
of_property_read_u64() will always return -ENOSYS for !CONFIG_OF.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_warn() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Maxime Ripard
Roger Quadros
Thomas Petazzoni
pekon gupta
Dan Carpenter
Sasha Levin
Herve Codina
Brian Norris
Linus Torvalds
Benjamin Herrenschmidt
Huang Shijie
Sachin Kamat
Wei Yongjun
Huang Shijie
Rodolfo Giometti
Uwe Kleine-König
Ezequiel Garcia
Gerhard Sittig
Prabhakar Kushwaha
Cai Zhiyong
Josh Triplett
Jingoo Han