The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.
Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous patch assumes the ioctl already existed, when
it actually didn't.
It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: I2C STU300 stability updates
i2c-omap: Enable workaround for Errata 1.153 based on
i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
i2c-omap: Fix I2C status ACK
- blk clk is enabled when an irq arrives. The clk should be enabled,
but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
downwards.
- Number of address send attempts before giving up is increased to 12
from 10 since it most times take 8 tries before getting through.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.
The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: teardown crtc correctly when fb is destroyed.
drm/kms/radeon: cleanup combios TV table like DDX.
drm/radeon/kms: memset the allocated framebuffer before using it.
drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
drm/radeon/kms: implement bo busy check + current domain
drm/radeon/kms: cut down indirects in register accesses.
drm/radeon/kms: Fix up vertical blank interrupt support.
drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
drm/edid: fixup detailed timings like the X server.
drm/radeon/kms: Add specific rs690 authorized register table
If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.
Signed-off-by: Dave Airlie <airlied@redhat.com>
LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero. We take these to
mean that the default values (8 bits per word, or maximum bus speed).
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.
Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
net: restore gnet_stats_basic to previous definition
NETROM: Fix use of static buffer
e1000e: fix use of pci_enable_pcie_error_reporting
e1000e: WoL does not work on 82577/82578 with manageability enabled
cnic: Fix locking in init/exit calls.
cnic: Fix locking in start/stop calls.
bnx2: Use mutex on slow path cnic calls.
cnic: Refine registration with bnx2.
cnic: Fix symbol_put_addr() panic on ia64.
gre: Fix MTU calculation for bound GRE tunnels
pegasus: Add new device ID.
drivers/net: fixed drivers that support netpoll use ndo_start_xmit()
via-velocity: Fix test of mii_status bit VELOCITY_DUPLEX_FULL
rt2x00: fix memory corruption in rf cache, add a sanity check
ixgbe: Fix receive on real device when VLANs are configured
ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon FCP_RSP in DDP completion
netxen: free napi resources during detach
netxen: remove netxen workqueue
ixgbe: fix issues setting rx-usecs with legacy interrupts
can: fix oops caused by wrong rtnl newlink usage
...
Recent commit c8c00a6915
changed the exit paths in do_md_stop and was not quite
careful enough. There is one path were 'err' now needs
to be cleared but it isn't.
So setting an array to readonly (with mdadm --readonly) will
work, but will incorrectly report and error: ENXIO.
Signed-off-by: NeilBrown <neilb@suse.de>
This implements the busy ioctl along with a current domain check.
returns 0 or -EBUSY
puts the current domain no matter what the answer.
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/md/dm-log-userspace-transfer.c:110: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'
Previously posted and acked, but apparently lost.
http://lkml.indiana.edu/hypermail/linux/kernel/0906.2/02074.html
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: dm-devel@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer
support for e1000e, but it is not reasonable to disable it in
e1000_remove but enable it in e1000_resume. This patch enables aer
support in e1000_probe.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get
configured on newer parts which use PHY wakeup vs. MAC wakeup which causes
WoL to not work. The driver should configure PHY wakeup whether or not
manageability is enabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path ulp_init and ulp_exit calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock. Fix it by using mutex and refcount during these
calls. cnic_unregister_driver() will now wait for the refcount
to go to zero before completing the call.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path ulp_start and ulp_stop calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock. Fix it by using mutex and setting a bit during
these calls. cnic_unregister_device() will now wait for the bit
to clear before completing the call.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slow path calls to the cnic driver are sleepable calls so we
cannot use rcu_read_lock(). Use mutex for these slow path calls
instead.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register and unregister with bnx2 during NETDEV_UP and NETDEV_DOWN
events. This simplifies the sequence of events and allows locking
fixes in the next patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the cnic driver tries to grab a symbol from bnx2 when bnx2 is
running init code, symbol_get() will succeed but symbol_put_addr()
will hit BUG() a moment later. module_text_address() fails because
bnx2 is still in init code.
This is fixed by using symbol_put() instead which does the exact
opposite of symbol_get().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We really don't want to be doing all these indirects, updating
the GPU gart table is something we do often so the less overhead the
better.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes 3D apps timing out in the WAIT_VBLANK ioctl.
AVIVO bits compile-tested only.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch updates the SuperH CMT driver with suspend and resume
callbacks for the suspend-to-ram case. This patch stops the CMT
channel at suspend time to avoid unwanted wake up events.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH Mobile LCDC driver to skip
over disabled channels. Without this patch suspend-to-ram
operation will crash if deferred io is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
this syncs the versioning check with the code the X server uses.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs690 is r3xx 3D engine with AVIVO modesetting so we need to allow
AVIVO register for vline synchronization. This add a specific table
to rs690 to handle that. Thanks to Marc (marvin24) for debugging
this and kudos to Andre (taiu1) for spotting the origin of the bugs.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add new definition to 'pegasus.h' for support Japanese IO DATA
"ETX-US2" USB Ethernet Adapter.
PEGASUS_DEV( $B!H(BIO DATA USB ETX-US2$B!I(B, VENDOR_IODATA, 0x092a,
DEFAULT_GPIO_RESET | PEGASUS_II )
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of spin_lock_irq() and spin_unlock_irq()
in the NETPOLL API callbacks causes the interrupts to get enabled and
can lead to kernel instability.
The solution is to use spin_lock_irqsave() and spin_unlock_restore()
to prevent the irqs from getting enabled while in netpoll_send_skb().
Call trace:
netpoll_send_skb()
{
-> local_irq_save(flags)
---> dev->ndo_start_xmit(skb, dev)
---> spin_lock_irq()
---> spin_unlock_irq() *******here would enable the interrupt.
...
-> local_irq_restore(flags)
}
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test whether VELOCITY_DUPLEX_FULL bit is set in mii_status.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the setting and clearing of the mutex's to
_config_request. There was a mutex deadlock when diag reset is called from
inside _config_request, so diag reset was moved to outside the mutexs.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf
register number. This is needed because the rf registers are enumerated
starting with one. The size of the rf register cache is just enough to
hold all registers, so writing to the highest register was corrupting
memory. Add a check to make sure that the rf register number is valid.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Traffic received with a priority tag (VID = 0) and non-zero priority value was
incorrectly handled by the VLAN packet code path due to a check on zero for
the whole VLAN tag instead of just the VID.
This patch masked out the priority field when checking the vlan tag for
received VLAN packets.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that
have been DDPed. However, it is possible that the length is 0, e.g., for SCSI
READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP
data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed
packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP,
we do not want to return the 0 ddp->len as we want FCP_RSP to be always
delivered to the upper layer. This patch fixes this bug by setting rc only if
ddp->len is non-zero.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The typo causes drivers/serial/s3c6400.c not being built for s3c6400 platform.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[].
Subsequently an attempt is made to load the firmware from the resulting
filename.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes most frontend drivers to allocate their state structure via
kzalloc and not kmalloc. This is done to properly initialize the
embedded "struct dvb_frontend frontend" field, that they all have.
The visible effect of this struct being uninitalized is, that the member "id"
that is used to set the name of kernel thread is totally random.
Some board drivers (for example cx88-dvb) set this "id" via
videobuf_dvb_alloc_frontend but most do not.
So I at least get random id values for saa7134, flexcop and ttpci based cards.
It looks like this in dmesg:
DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S)
The related kernel thread then also gets a strange name
like "kdvb-ad-1-fe--1".
Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Timothy Lee <timothy.lee@siriushk.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It tested the value of stk_sizes[i].m before checking whether i was in range.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore support for digital tuning caused by regression during introduction
of disable_i2c_gate parameter to zl10353 driver.
Thanks to user "Xwang" for reporting the problem and testing the fix
Cc: Xwang <xwang1976@email.it>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l core supplies default handlers for G_STD and G_PARM. However, both
default handlers are buggy.
This patch fixes the following:
1) If no g_std is supplied and current_norm == 0, then this driver does not
support TV video standards (e.g. a radio or webcam driver). Return
-EINVAL. This ensures that there is no bogus VIDIOC_G_STD support for
such drivers.
2) The default VIDIOC_G_PARM handler used current_norm instead of first
checking if the driver supported g_std and calling that to get the norm.
It also didn't check if current_norm was 0, since in that case the driver
does not support TV standards (or no standard was set at all) and the
default handler should return -EINVAL.
Note that I am very unhappy with these default handlers: I think they
basically behave like some very strange and unexpected side-effect.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers should either set current_norm or supply a g_std callback.
The hdpvr driver does neither. Since it initializes to a 60 Hz format
I've initialized the current_norm to NTSC | PAL_M | PAL_60 which is the
60 Hz subset of tvnorms.
Cc: Janne Grunau <j@jannau.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The .buf_queue() V4L2 driver method is called under
spinlock_irqsave(q->irqlock,...), don't take the lock again inside the
function.
Reported-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix build errors in zr364xx by adding selects:
zr364xx.c:(.text+0x195ed7): undefined reference to `videobuf_streamon'
zr364xx.c:(.text+0x196030): undefined reference to `videobuf_dqbuf'
zr364xx.c:(.text+0x1960c4): undefined reference to `videobuf_qbuf'
zr364xx.c:(.text+0x196123): undefined reference to `videobuf_querybuf'
zr364xx.c:(.text+0x196182): undefined reference to `videobuf_reqbufs'
zr364xx.c:(.text+0x196224): undefined reference to `videobuf_queue_is_busy'
zr364xx.c:(.text+0x196390): undefined reference to `videobuf_vmalloc_free'
zr364xx.c:(.text+0x196571): undefined reference to `videobuf_iolock'
zr364xx.c:(.text+0x196678): undefined reference to `videobuf_mmap_mapper'
zr364xx.c:(.text+0x196760): undefined reference to `videobuf_poll_stream'
zr364xx.c:(.text+0x19689a): undefined reference to `videobuf_read_one'
zr364xx.c:(.text+0x1969ec): undefined reference to `videobuf_mmap_free'
zr364xx.c:(.text+0x197862): undefined reference to `videobuf_queue_vmalloc_init'
zr364xx.c:(.text+0x197a28): undefined reference to `videobuf_streamoff'
zr364xx.c:(.text+0x198203): undefined reference to `videobuf_to_vmalloc'
zr364xx.c:(.text+0x198603): undefined reference to `videobuf_streamoff'
drivers/built-in.o: In function `free_buffer':
zr364xx.c:(.text+0x19930c): undefined reference to `videobuf_vmalloc_free'
drivers/built-in.o: In function `zr364xx_open':
zr364xx.c:(.text+0x19a7de): undefined reference to `videobuf_queue_vmalloc_init'
drivers/built-in.o: In function `read_pipe_completion':
zr364xx.c:(.text+0x19b17f): undefined reference to `videobuf_to_vmalloc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 0x13 seems to be a sort of image control, maybe gamma, white
level or black level. Lower values produce better images, while higher
values increases the contrast and shifts colors to green. 0xff produces
a black image. This register is not Silvercrest-specific, so its code
should be moved to a better place.
If this register is left alone, a random value can be found at the
register, producing weird results.
While here, let's remove register 0x0d, as it had no noticed effect at
the image.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Silvercrest mt9v011 sensor produces a 640x480 image. However,
previously, the code were getting only half of the lines and merging two
consecutive frames to "produce" a 640x480 image.
With the addition of progressive mode, now em28xx is working with a full
image. However, when the number of lines is bigger than 240, the
beginning of some odd lines are filled with blank.
After lots of testing, and physically checking the device for a Xtal, it
was noticed experimentally that mt9v011 is using em28xx XCLK as its
clock. Due to that, changing XCLK value changes the maximum speed of the
stream.
At the tests, it were possible to produce up to 32 fps, using a 30 MHz
XCLK. However, at that rate, the artifacts happen even at 320x240. Lower
values of XCLK produces artifacts only at 640x480.
At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is
possible to see an invalid sucession of artifacts with this pattern:
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
(where the dots represent the blanked pixels)
So, it seems that a waveform in the format of a ramp is interferring at
the image.
The cause of this interference is currently unknown. Some possibilities
are:
- electrical interference (maybe this device is broken?);
- some issue at mt9v011 programming;
- some bug at em28xx chip.
So, for now, let's be conservative and use a value of XCLK that we know
for sure that it won't cause artifacts.
As I'm waiting for more of such devices with different em28xx chipset
revisions, I'll have the opportunity to double check the issue with
other pieces of hardware.
Later patches can vary XCLK depending on the vertical resolutions, if a
proper fix is not discovered.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.
Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't know the xtal frequency of Silvercrest, but we need to have
some value in order to allow controlling the frame rate frequency. The
value is probably still wrong, since the manufacturer announces this
device as being capable of 30fps, but the maximum we can get is
13.5 fps.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:
1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;
2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):
em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx doesn't have temporal scaling. However, on webcams, sensors are
capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should
be passed to the sensor for it to properly set frame rate.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement g_parm/s_parm ioctls. Those are used to check the current
frame rate (in fps) and to set it to a value. In practice, there are
only 15 possible different speeds, due to chip limits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced. The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured. Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.
Thanks to user "ritec" for reporting the issue and testing the fix.
Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate). Add the needed parameter.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the following build warning:
sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'
Thanks to Hans Verkuil for pointing this out.
The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The iSight sends non-UVC status events through the interrupt endpoint. Those
invalid events are reported to the kernel log, resulting in a log flood.
Only log the events when the UVC_TRACE_STATUS flag is set.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 50144aeeb7 broke the Samsung NC10
netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro
devices, list the devices explicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current GPIO configuration breaks all Hauppauge devices.
The code being removed affects Hauppauge devices only,
and is the cause of the breakage.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of
the norm passed. This patch sets cx23885_mpeg_template.tvnorms and
cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work.
Thanks to Joseph Yasi for pointing this out, even though this particular
fix was already pushed into a development repository, merge priority of
this changeset has been escalated as a result of Joseph posting this
identical patch.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Joseph A. Yasi <joe.yasi@gmail.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Current tip is broken and does not switch back to DVB-T correctly
Signed-off-by: Sohail Syyed <linuxtv@hubstar.net>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.
Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Tested-by: Angelo Cano <acano@fastmail.fm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.
The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.
Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This mistakenly tested against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This mistakenly tests against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
o Defer napi resouce allocation to device attach.
o Free napi resources and delete napi during detach.
This ensures right behavior across firmware reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove private workqueue in the driver, move all
scheduled tasks to keventd workqueues. This makes
ports (interfaces) of same / different NIC boards
independent, in terms of their link watchdog and
reset tasks.
o Move quick checks for link status and temperature
in timer callback, schedule watchdog task only if
link status changed or temperature reached critical
threshold.
This also fixes deadlock when thermal panic occurs,
watchdog work was flushing workqueue that it was
sitting on.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently setting rx-usecs when the interface is in legacy interrupt
mode it is not immediate. We were only setting EITR for each MSIx
vector and since this count would be zero for legacy mode it wasn't
set until after a reset. This patch corrects that by checking what
mode we are in and then setting EITR accordingly.
Signed-off-by: Don Skidmore <donald.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created with
the ip tool ...
The invocation of 'ip link add type can' lead to an oops as the standard rtnl
newlink function was called:
http://bugzilla.kernel.org/show_bug.cgi?id=13954
This patch adds a private newlink function for the CAN device driver interface
that unconditionally returns -EOPNOTSUPP.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix another ocurring when the system resumes. This oops was due to driver
setting the pci drvdata to NULL on the prior hibernation. Becuase it was
set to NULL, upon resmume we assume the pci drvdata is non-zero, and we oops.
To fix the ooops, we don't set pci drvdata to NULL at hibernation time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix oops ocurring at hibernation time. This oops was due to the firmware fault
watchdog timer still running after we freed resources. To fix the issue we need
to terminate the watchdog timer at hibernation time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This restriction is introduced just to avoid loop of
config_request. Retry must be limited so we have restricted
config request to maximum 2 times.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Inhibit 0x3117 loginfos - during cable pull, there are too many printks going
to the syslog, this is have impact on how fast the interrupt routine can handle
keeping up with command completions; this was the root cause to the config
pages timeouts.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a volume is activated, the driver will recieve a pair of ir config change
events to remove the foreign volume, then add the native.
In the process of the removal event, the hidden raid componet is removed from
the parent.When the disks is added back, the adding of the port fails becuase
there is no instance of the device in its parent.
To fix this issue, the driver needs to call mpt2sas_transport_update_links()
prior to calling _scsih_add_device. In addition, we added sanity checks on
volume add and removal to ignore events for foreign volumes.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because driver did not tear down the port which should
be dnoe using mpt2sas_transport_port_remove(). without this fix When expander
is added back we would oops inside sas_port_add_phy.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because of enclosure_handle received from FW is zero.
Check is introduced before calling mpt2sas_config_get_enclosure_pg0.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-linus' of git://neil.brown.name/md:
md: allow upper limit for resync/reshape to be set when array is read-only
md/raid5: Properly remove excess drives after shrinking a raid5/6
md/raid5: make sure a reshape restarts at the correct address.
md/raid5: allow new reshape modes to be restarted in the middle.
md: never advance 'events' counter by more than 1.
Remove deadlock potential in md_open
The driver always:
1. allocate cp->rx_buf_sz + NET_IP_ALIGN
2. map cp->rx_buf_sz
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally we only allow the upper limit for a reshape to be decreased
when the array not performing a sync/recovery/reshape, otherwise there
could be races. But if an array is part-way through a reshape when it
is assembled the reshape is started immediately leaving no window
to set an upper bound.
If the array is started read-only, the reshape will be suspended until
the array becomes writable, so that provides a window during which it
is perfectly safe to reduce the upper limit of a reshape.
So: allow the upper limit (sync_max) to be reduced even if the reshape
thread is running, as long as the array is still read-only.
Signed-off-by: NeilBrown <neilb@suse.de>
We were removing the drives, from the array, but not
removing symlinks from /sys/.... and not marking the device
as having been removed.
Signed-off-by: NeilBrown <neilb@suse.de>
This reverts commit 57921c312e.
On request from John Linville:
It has been shown to create a new problem. There is work
towards a solution to that one, but it isn't a simple
clean-up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie
Thomas Hellstrom
Linus Torvalds
Linus Walleij
Moiz Sonasath
Nishanth Menon
Alek Du
Ben Dooks
NeilBrown
Randy Dunlap
Xiaotian Feng
Bruce Allan
Michael Chan
Michel Dänzer
Magnus Damm
Jerome Glisse
Petko Manolov
Dongdong Deng
roel kluin
David S. Miller
Kashyap, Desai
Pavel Roskin
Lucy Liu
Yi Zou
Ramax Lo
Matthias Schwarzott
Devin Heitmueller
Hans Verkuil
Guennadi Liakhovetski
Mauro Carvalho Chehab
Michael Krufky
Laurent Pinchart
Nils Kassube
Sohail Syyed
Jan Nikitenko
Andy Walls
Antonio Ospite
Dhananjay Phadke
Amit Kumar Salecha
Don Skidmore
Oliver Hartkopp
Francois Romieu