The recent change for supporting dynamic beep device allocation caused
a problem resulting in Oops at reloading the driver. Also, it ignores
the error from input device registration.
This patch fixes the wrong check in snd_hda_detach_beep_device(), and
returns an error when the input device registration fails properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few lines earlier we assume that best->slave could be either null or non-null so
we should check it here as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f001fde5ea changed
net_device.dev_addr from a 32-byte array to a pointer.
I found 4 ethernet drivers which rely on sizeof(dev_addr), which are now
only copying 4 bytes of the address information on 32bit systems.
Fix them to use ETH_ALEN.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfar_select_queue() function was used to set queue mapping
only for forwarding/bridging applications and the condition
for locally generated packets was completely ignored.
The solution is to remove the gfar_select_queue() function and
use skb_record_rx_queue to set queue mapping for
forwarding/bridging applications. This will ensure that in case of
forwarding/bridging applications txq = rxq will be selected and
skb_tx_hash will be used to pick up a txq for locally generated packets.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using macro tun_sk is more clear and shorter. However tun.c has tun_sk,
but doesn't use it.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PHY doesn't have an IRQ, phylib would poll for link changes, and
would call adjust_link() every second. In that case we disable and
enable the controller every second.
Let's better check if there is actually anything changed, and, if so,
change the MAC settings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 864fdf884e ("ucc_geth:
Fix hangs after switching from full to half duplex") ucc_geth driver
disables the controller during MAC configuration changes. Though,
disabling the controller might take quite awhile, and so the netdev
watchdog might get upset:
NETDEV WATCHDOG: eth2 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c02729a8 [verbose debug info unavailable]
NIP: c02729a8 LR: c02729a8 CTR: c01b6088
REGS: c0451c40 TRAP: 0700 Not tainted (2.6.32-trunk-8360e)
[...]
NIP [c02729a8] dev_watchdog+0x280/0x290
LR [c02729a8] dev_watchdog+0x280/0x290
Call Trace:
[c0451cf0] [c02729a8] dev_watchdog+0x280/0x290 (unreliable)
[c0451d50] [c00377c4] run_timer_softirq+0x164/0x224
[c0451da0] [c0032a38] __do_softirq+0xb8/0x13c
[c0451df0] [c00065cc] do_softirq+0xa0/0xac
[c0451e00] [c003280c] irq_exit+0x7c/0x9c
[c0451e10] [c00640c4] __ipipe_sync_stage+0x248/0x24c
[...]
This patch fixes the issue by detaching the netdev during the
time we change the configuration.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
Following oops was seen with the ucc_geth driver:
Unable to handle kernel paging request for data at address 0x00000058
Faulting instruction address: 0xc024f2fc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c024f2fc] skb_recycle_check+0x14/0x100
LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
Call Trace:
[df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable)
[df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
[df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8
[df857e10] [c0032a38] __do_softirq+0xb8/0x13c
[df857e60] [c00065cc] do_softirq+0xa0/0xac
[...]
This is because ucc_geth_tx() tries to process an empty queue when
queues are logically stopped. Stopping the queues doesn't disable
polling, and since nowadays ucc_geth_tx() is actually called from
the polling routine, the oops above might pop up.
Fix this by removing 'netif_queue_stopped() == 0' check.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
Document that rfkill and ALSA functionality exists, but requires the
subsystems to be available, and not modular if thinkpad-acpi is not
modular.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Allow the user to choose through Kconfig if the Console Audio Control
interface (aka "volume subdriver") should be available or not.
This not only saves some memory, but also allows the thinkpad-acpi
driver to be built-in even if ALSA is modular when the console audio
control interface is not wanted.
This change fixes a build problem that is causing some annoyances, in
a way that doesn't disable the entire driver on kernels without ALSA
support.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Helight Xu <helight.xu@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
If we cannot create the ALSA mixer, it is a good reason to fail to
load the volume subdriver, and not to fail to load the entire module.
While at it, add more debugging messages, as the error paths are being
used a lot more than I'd expect, and it is failing to set up the ALSA
mixer on a number of ThinkPads.
Reported-by: Peter Jordan <usernetwork@gmx.info>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't want to be the first soundcard. We don't want to shift other
soundcards out of the way either, even if they load much later.
Ask ALSA to (by default) load us in one of the last three slots. This
can be overriden at will using the "index" parameter.
Reported-by: Whoopie <whoopie79@gmx.net>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
when using policy routing and the skb mark:
there are cases where a back path validation requires us
to use a different routing table for src ip validation than
the one used for mapping ingress dst ip.
One such a case is transparent proxying where we pretend to be
the destination system and therefore the local table
is used for incoming packets but possibly a main table would
be used on outbound.
Make the default behavior to allow the above and if users
need to turn on the symmetry via sysctl src_valid_mark
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is reset during MTU change, ring size change, or self
test, etc, the cnic status block needs to be properly initialized if
cnic is registered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, some distros have started shipping versions of gcc which
default to -march=i686. This breaks building kernels for pre-i686
machines, even if they have been selected in Kconfig, due to the
generation of CMOV instructions.
There isn't enough benefit to try to preserve the generation of these
instructions even when selected, so simply force -march=i386 for the
decompressor when building a 32-bit kernel.
Reported-and-tested-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <219280.97558.qm@web52907.mail.re2.yahoo.com>
Use snd_hda_jack_detect() again for jack-sensing.
The triggering problem can be worked around with codec->no_trigger_sense
flag now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Analog Device codecs seem to have problems with the triggering of
pin-sensing although their pincaps give the trigger requirements.
Some reported that constant CPU load on HP laptops with AD codecs.
For avoiding this regression, add a flag to codec struct to notify
explicitly that the codec doesn't suppot the trigger at pin-sensing.
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When ext4_da_writepages increases the nr_to_write in writeback_control
then it must always re-base the return value. Originally there was a
(misguided) attempt prevent wbc.nr_to_write from going negative. In
fact, it's necessary to allow nr_to_write to be negative so that
wb_writeback() can correctly calculate how many pages were actually
written.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When we run the following commands in turn (with
CONFIG_SND_HDA_POWER_SAVE_DEFAULT=0),
speaker-test -Dhw:0,3 -c2 -twav # HDMI
speaker-test -Dhw:0,0 -c2 -twav # Analog
The second command will produce sound in the analog lineout _as well as_
HDMI sink. The root cause is, device 0 "reuses" the same stream tag that
was used by device 3, and the "intelhdmi - sticky stream id" patch leaves
the HDMI codec in a functional state. So the HDMI codec happily accepts
the audio samples which reuse its stream tag.
The proposed solution is to remember the last device each azx_dev was
assigned to, and prefer to
1) reuse the azx_dev (and hence the stream tag) the HDMI codec last used
2) or assign a never-used azx_dev for HDMI
With this patch and the above two speaker-test commands,
HDMI codec will use stream tag 8 and Analog codec will use 5.
The stream tag used by HDMI codec won't be reused by others, as long
as we don't run out of the 4 playback azx_dev's. The legacy Analog
codec will continue to use stream tag 5 because its device id is 0
(this is a bit tricky).
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On certain boards not all GPIOs may be used as wakeup sources, in which
case some of enable_irq_wake() calls will fail. On resume calling
disable_irq_wake() will warn about unbalanced IRQ wake disable.
Solve this by checking whether enable_irq_wake() succeeded or not and
no not call disable_irq_wake() for these GPIOs/IRQs that have not been
enabled.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not try to free iforce device when we closing input device; disconnect
is the only place where it should be deleted.
Reported-by: Johannes Ebke <johannes.ebke@physik.uni-muenchen.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds simple direction calculation when combining effects. It's useful
to decide motor direction for rumble (vibrator).
Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The commit 9e68177ef9 changed 'gain' from
signed to unsigned to fix an issue with rumble effect calculation, however
it introduced problems when calculating constant effects. Having 'gain'
being unsigned int was an unfortunate choice since it dominates all
implicit type conversions causing everything to be treated as unsigned
int.
Let's change it back to signed int and simply add proper casts to rumble
effect calculations.
Reported-by: Gary Stein <lordcnidarian@gmail.com>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of waiting for the next timer tick to start playing an effect
do it immediately. This mostly helps systems using low HZ setting.
Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We used to make kseriod freezable to prevent unnecessary attempts at
resuming keyboard and mouse before taking hibernation image when suspend
and hibernation were sharing PM operations. Now that they are separated
and we don't risk resuming during 'thaw' we don't need to freeze kseriod
anymore. This will allow us to start resetting mouse and keyboard a bit
earlier, before rest of the userspace comes back up.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of doing full-blown reset while suspending or shutting down
the box use lighter form of reset that should take less time.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
This is a trivial style fix patch to mend errors/warnings
reported by "checkpatch.pl --file".
Signed-off-by: Jiro SEKIBA <jir@unicus.jp>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Per commit 240799cd, the option name for readahead should be
inode_readahead_blks, not inode_readahead.
Signed-off-by: Fang Wenqi <antonf@turbolinux.com.cn>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'sysctl' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-misc-2.6:
SYSCTL: Add a mutex to the page_alloc zone order sysctl
SYSCTL: Print binary sysctl warnings (nearly) only once
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
classmate-laptop: add support for Classmate PC ACPI devices
hp-wmi: Fix two memleaks
acer-wmi, msi-wmi: Remove needless DMI MODULE_ALIAS
dell-wmi: do not keep driver loaded on unsupported boxes
wmi: Free the allocated acpi objects through wmi_get_event_data
drivers/platform/x86/acerhdf.c: check BIOS information whether it begins with string of table
acerhdf: add new BIOS versions
acerhdf: limit modalias matching to supported
toshiba_acpi: convert to seq_file
asus_acpi: convert to seq_file
ACPI: do not select ACPI_DOCK from ATA_ACPI
sony-laptop: enumerate rfkill devices using SN06
sony-laptop: rfkill support for newer models
ACPI: fix OSC regression that caused aer and pciehp not to load
MAINTAINERS: add maintainer for msi-wmi driver
fujitu-laptop: fix tests of acpi_evaluate_integer() return value
arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.c: avoid cross-CPU interrupts by using smp_call_function_any()
ACPI: processor: remove _PDC object list from struct acpi_processor
ACPI: processor: change acpi_processor_set_pdc() interface
ACPI: processor: open code acpi_processor_cleanup_pdc
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2/trivial: Use le16_to_cpu for a disk value in xattr.c
ocfs2/trivial: Use proper mask for 2 places in hearbeat.c
Ocfs2: Let ocfs2 support fiemap for symlink and fast symlink.
Ocfs2: Should ocfs2 support fiemap for S_IFDIR inode?
ocfs2: Use FIEMAP_EXTENT_SHARED
fiemap: Add new extent flag FIEMAP_EXTENT_SHARED
ocfs2: replace u8 by __u8 in ocfs2_fs.h
ocfs2: explicit declare uninitialized var in user_cluster_connect()
ocfs2-devel: remove redundant OCFS2_MOUNT_POSIX_ACL check in ocfs2_get_acl_nolock()
ocfs2: return -EAGAIN instead of EAGAIN in dlm
ocfs2/cluster: Make fence method configurable - v2
ocfs2: Set MS_POSIXACL on remount
ocfs2: Make acl use the default
ocfs2: Always include ACL support
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: pci_request_regions needs a persistent name
ARM: dma-isa: request cascade channel after registering it
ARM: footbridge: trim down old ISA rtc setup
ARM: fix PAGE_KERNEL
ARM: Fix wrong shared bit for CPU write buffer bug test
ARM: 5857/1: ARM: dmabounce: fix build
ARM: 5856/1: Fix bug of uart0 platfrom data for nuc900
ARM: 5855/1: putc support for nuc900
ARM: 5854/1: fix compiling error for NUC900
ARM: 5849/1: ARMv7: fix Oprofile events count
ARM: add missing include to nwflash.c
ARM: Kill CONFIG_CPU_32
ARM: Convert VFP/Crunch/XscaleCP thread_release() to exit_thread()
ARM: 5853/1: ARM: Fix build break on ARM v6 and v7
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Ensure all PG_dcache_dirty pages are written back.
sh: mach-ecovec24: setup.c detailed correction
serial: sh-sci: Convert tremaining ctrl_xxx I/O routines to __raw_xxx.
serial: sh-sci: earlyprintk zero uartclk fix
sh: Only use bl bit toggling for sleeping idle.
sh: Restore bl bit toggling in idle loop.
sh: Fix up MAX_DMA_CHANNELS definition when DMA is disabled.
sh: dmaengine support for SH7785
sh: dmaengine support for sh7724.
Don't pass a name pointer from the kernel stack, it will not survive
and will result in corrupted /proc/iomem output.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a "start_kernel(): bug: interrupts were enabled early".
rtc_cmos now takes care of initializing the ISA RTC and reading the
current time and date from it; there's no need to repeat that here,
thereby causing interrupts to be enabled too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sevelar ASoC codec drivers wrongly assume, that the params_rate() macro
returns one of SNDRV_PCM_RATE_* defines instead of the actual numerical
sampling rate. Fix them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I2C devices should be registered when platform board setting
in latest ASoC.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai