The list of rports might become stale so we should rather traverse the
discovery list when trying relogin.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent race where we're removing the module and we get link update
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem Statement:
- Driver has fc_id of 0xcc0200
- Driver gets link down (due to test) and calls fcoe_ctlr_link_down().
- At this point, the fc_id of the initiator port is zeroed out.
- Driver gets a link up 14 seconds later.
- Driver performs FIP VLAN request, gets a response from the switch.
- No change in VLAN is detected.
- Driver then notifies libfcoe via fcoe_ctlr_link_up().
- Libfcoe then issues a multicast discovery solicitation as expected.
- Cisco FCF responds to that correctly.
- Libfcoe at this point starts a 3 sec count-down to allow any other FCFs
to be discovered. However, at this point, it has been 20 seconds since
the last FKA from the driver (which would have been sent prior to
backlink toggle), which causes the CVL to be issued from Cisco CVL from
the switch is dropped by the driver as the vx_port identification
descriptor is present and has value of 0xcc0200, which does not match
the driver's value of 0. Libfcoe completes the 3 sec count down and
proceeds to issue FLOGI as per protocol. Switch rejects FLogi request.
All subsequent FLOGI requests from libfc are rejected by the switch
(possibly because it is now expecting a new solicitation). This
situation will continue until the next link toggle.
Solution:
The Vx_port descriptor in the CVL has three fields:
MAC address
Fabric ID
Port Name
Today, the code checks for both #1 and #2 above. In the case where we went
through a link down, both these will be zero until FLOGI succeeds.
We should change our code to check if any one of these 3 is valid and if
so, handle the CVL (basically switching from AND to OR). The port name
field is definitely expected to be valid always.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Log s_id, d_id, type and command to the log message.
[mkp: fixed warning]
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current code doeesn't support 20Gbps speed for current and supported
speed. Add support for it.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was wrongly interpreting the supported cap value returned by qed.
Solution: Use QED define macros instead of OS defined for interpreting
supporting speeds.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was attempting to print cdb[0], which is not set for resets coming
from SCSI ioctls. Check for cmd_len before accessing cmnd.
Crash info:
[84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null)
[84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf]
[84790.865204] Call Trace:
[84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod]
[84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod]
[84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod]
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- On some setups fipvlan can be retried for long duration and the
connection to switch was not there so it was not getting any reply.
- During unload this thread was hanging.
Problem Resolution:
Check if unload is in progress, then quit from fipvlan thread.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print messages during exiting condition to help debugging.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add:
PM8222 VID_9005, DID_028F, SVID_1BD4 and SDID_004F
3101E-4i (1G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0808
3102E-8i (2G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0809
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return -EINPROGRESS when a rescan worker is queued.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When each ld is deleted, a rescan event is triggered in the driver. These
can stack up waiting on mutex_lock.
Change to mutex_try_lock and schedule a rescan for later.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Return identify physical device "Phys_Bay_in_Box" as bay_identifier.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- serial number
- model
- vendor
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expose physical devices before logical devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes: c00f62e6c5 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Raise the config max for lpfc_fcp_mq_threshold variable to 256.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Capturing and downloading dif command data and dif data was done a dozen
years ago and no longer being used. Also creates a potential security hole.
Remove the debugfs buffer for dif debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per Dan Carpenter:
The patch d79c9e9d4b3d: "scsi: lpfc: Support dynamic unbounded SGL lists on
G7 hardware." from Aug 14, 2019, leads to the following static checker
warning:
drivers/scsi/lpfc/lpfc_init.c:4107 lpfc_new_io_buf()
error: not allocating enough data 784 vs 768
There was no need to compare sizes nor to allocate size based on a define.
Change allocation to use actual structure length
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/ufs/ufs-qcom.c: In function ufs_qcom_pwr_change_notify:
drivers/scsi/ufs/ufs-qcom.c:808:6: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 1e1e465c6d ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function cq_interrupt_v1_hw:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1542:6: warning: variable irq_value set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the
protocol-specific value set by the driver (the default) or the maximum
supported by the controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth
of individual scsi devices, this implementation provides a single
sysfs entry per shost to switch between the controller max and the
driver default.
[mkp: tweaked commit desc]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the firmware documentation a status type 0 IOCB can be
followed by one or more status continuation type 0 IOCBs. Hence do not
complain if the completion function is not called from inside the status
type 0 IOCB handler.
WARNING: CPU: 10 PID: 425 at drivers/scsi/qla2xxx/qla_isr.c:2784
qla2x00_status_entry.isra.7+0x484/0x17b0 [qla2xxx]
CPU: 10 PID: 425 Comm: kworker/10:1 Tainted: G E 5.3.0-rc4-next-20190813-autotest-autotest #1
Workqueue: qla2xxx_wq qla25xx_free_rsp_que [qla2xxx]
Call Trace:
qla2x00_status_entry.isra.7+0x1484/0x17b0 [qla2xxx] (unreliable)
qla24xx_process_response_queue+0x7d8/0xbd0 [qla2xxx]
qla25xx_free_rsp_que+0x1a0/0x220 [qla2xxx]
process_one_work+0x25c/0x520
worker_thread+0x8c/0x5e0
kthread+0x154/0x1a0
ret_from_kernel_thread+0x5c/0x7c
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently bits in hba->outstanding_tasks are cleared only after their
corresponding task management commands are successfully done by
__ufshcd_issue_tm_cmd().
If timeout happens in a task management command, its corresponding bit in
hba->outstanding_tasks will not be cleared until next task management
command with the same tag used successfully finishes.
This is wrong and can lead to some issues, like power issue. For example,
ufshcd_release() and ufshcd_gate_work() will do nothing if
hba->outstanding_tasks is not zero even if both UFS host and devices are
actually idle.
Solution is referred from error handling of device commands: bits in
hba->outstanding_tasks shall be cleared regardless of their execution
results.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer fh is being assigned a return value from the call to
skb_transport_header however this value is never read and fh is being
re-assigned immediately afterwards with a new value. Since there are
side-effects from calling skb_transport_header the call is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices have issues if LCC is enabled. So we are setting
PA_LOCAL_TX_LCC_Enable to 0 before link startup which will make sure that
both host and device TX LCC are disabled once link startup is completed.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable error is being initialized with a value that is never read and
error is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Four fixes, three for edge conditions which don't occur very often.
The lpfc fix mitigates memory exhaustion for some high CPU systems.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXWEBrCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishds+AQCyQlgV
TzSFQ1zvbAb3SNFdNsCzzb8Aq2vJC+RojF2VFgD/cJfE2fix9E7Nk8PCGwH1sgnf
m5Glsvv8BEmmtoikrb8=
=Ti6g
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes, three for edge conditions which don't occur very often.
The lpfc fix mitigates memory exhaustion for some high CPU systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Mitigate high memory pre-allocation by SCSI-MQ
scsi: ufs: Fix NULL pointer dereference in ufshcd_config_vreg_hpm()
scsi: target: tcmu: avoid use-after-free after command timeout
scsi: qla2xxx: Fix gnl.l memory leak on adapter init failure
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through.
- Fix fall-through warnings on arm and mips for multiple
configurations.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=fQZm
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull more fallthrough fixes from Gustavo A. R. Silva:
"Fix fall-through warnings on arm and mips for multiple configurations"
* tag 'Wimplicit-fallthrough-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
video: fbdev: acornfb: Mark expected switch fall-through
scsi: libsas: sas_discover: Mark expected switch fall-through
MIPS: Octeon: Mark expected switch fall-through
power: supply: ab8500_charger: Mark expected switch fall-through
watchdog: wdt285: Mark expected switch fall-through
mtd: sa1100: Mark expected switch fall-through
drm/sun4i: tcon: Mark expected switch fall-through
drm/sun4i: sun6i_mipi_dsi: Mark expected switch fall-through
ARM: riscpc: Mark expected switch fall-through
dmaengine: fsldma: Mark expected switch fall-through
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: mtx1_defconfig mips):
drivers/scsi/libsas/sas_discover.c: In function ‘sas_discover_domain’:
./include/linux/printk.h:309:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/libsas/sas_discover.c:459:3: note: in expansion of macro ‘pr_notice’
pr_notice("ATA device seen but CONFIG_SCSI_SAS_ATA=N so cannot attach\n");
^~~~~~~~~
drivers/scsi/libsas/sas_discover.c:462:2: note: here
default:
^~~~~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Update lpfc version to 12.4.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, each hardware queue, typically allocated per-cpu, consists of a
WQ/CQ pair per protocol. Meaning if both SCSI and NVMe are supported 2
WQ/CQ pairs will exist for the hardware queue. Separate queues are
unnecessary. The current implementation wastes memory backing the 2nd set
of queues, and the use of double the SLI-4 WQ/CQ's means less hardware
queues can be supported which means there may not always be enough to have
a pair per cpu. If there is only 1 pair per cpu, more cpu's may get their
own WQ/CQ.
Rework the implementation to use a single WQ/CQ pair by both protocols.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME
protocol. This allows for the detection of errors and lost frames and
immediate retransmission of data to avoid exchange termination, which
escalates into NVMeoFC connection and association failures. A significant
RAS improvement.
The driver is modified to indicate support for SLER in the NVMe PRLI is
issues and to check for support in the PRLI response. When both sides
support it, the driver will set a bit in the WQE to enable the recovery
behavior on the exchange. The adapter will take care of all detection and
retransmission.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI
to contain the exchanges Scatter/Gather List. This caps the number of SGL
elements that can be in the SGL. There are not extensions to extend the
list out of the 2 pages.
The G7 hardware adds a SGE type that allows the SGL to be vectored to a
different scatter/gather list segment. And that segment can contain a SGE
to go to another segment and so on. The initial segment must still be
pre-registered for the XRI, but it can be a much smaller amount (256Bytes)
as it can now be dynamically grown. This much smaller allocation can
handle the SG list for most normal I/O, and the dynamic aspect allows it to
support many MB's if needed.
The implementation creates a pool which contains "segments" and which is
initially sized to hold the initial small segment per xri. If an I/O
requires additional segments, they are allocated from the pool. If the
pool has no more segments, the pool is grown based on what is now
needed. After the I/O completes, the additional segments are returned to
the pool for use by other I/Os. Once allocated, the additional segments are
not released under the assumption of "if needed once, it will be needed
again". Pools are kept on a per-hardware queue basis, which is typically
1:1 per cpu, but may be shared by multiple cpus.
The switch to the smaller initial allocation significantly reduces the
memory footprint of the driver (which only grows if large ios are
issued). Based on the several K of XRIs for the adapter, the 8KB->256B
reduction can conserve 32MBs or more.
It has been observed with per-cpu resource pools that allocating a resource
on CPU A, may be put back on CPU B. While the get routines are distributed
evenly, only a limited subset of CPUs may be handling the put routines.
This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because
all the resources are being put on a limited subset of CPUs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To aid better hardware detection when there are issues, report the first
and second level hardware revisions from the READ_REV command. Add the
elements to the existing hardware id string.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to see real addresses, convert %p with %px for kernel addresses
and replace %p with %pf for functions.
While converting, standardize on "x%px" throughout (not %px or 0x%px).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While performing code review, several relatively simple optimizations can
be done in the fast path.
Add these optimizations (unlikely designators).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Running on Coverity produced the following errors:
- coding style (indentation)
- memset size mismatch errors
note: comment cases where it is purposely a mismatch
Fix the errors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is
not fully supported.
Update the attribute description
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is allowing the user to change lpfc_enable_bg while loading the
driver against a FCoE adapter. This is not supported.
No check is made for the adapter type when applying the blockguard
enablement value.
Fix by verifying the adapter type before setting the enablement flag.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk
and the link has gone down. The driver is not clearing the logical speed
as part of the link down transition.
Fix by setting the logical speed to UNKNOWN SPEED when the link goes down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Max Frame Size value is shown as 34816 in fdmishow from Switch.
The driver uses bbRcvSize in common service param which is obtained from
the READ_SPARM mailbox command. The bbRcvSize field which is displayed is a
three nibble field but the driver is printing a full four nibbles.
Fix by masking off the upper nibble.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi transport fc bsg interface does not expect the bsg_job_done()
callback to be done if the bsg request call returns failure. Several of the
HST_VENDOR cases in the driver unconditionally call bsg_job_done()
regardless of the returning value.
Fix the code to only call bsg_job_done() if the call to lpfc_bsg_request()
will return success.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When forcing the use of MSI (vs MSI-X) the driver is crashing in
pci_irq_get_affinity.
The driver was not using the new pci_alloc_irq_vectors interface in the MSI
path.
Fix by using pci_alloc_irq_vectors() with PCI_RQ_MSI in the MSI path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting a non-zero nvme sg_seg_cnt value of 256
when nvme is disabled. It should be zero.
Fix by ensuring the value is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an unsolicited ABTS was received, the driver looks up the exchange it
references. It it does various searches looking for the exchange
context. When one is eventually matched and it is associated with an XRI
context, the driver sends an ABORT WQE to terminate the exchange. Current
code looks at whether the transport had taken action on the XRI yet or not
(no action if set to LPFC_NVMET_STE_RCV; action if non-LPFC_NVMET_STE_RCV).
Based on action or not one of two (sol vs unsol) issue abort routines are
called. The unsol version cheats and transmits a sequence containing an
ABTS with no interaction with the adapter. The sol version issues an Abort
WQE and lets the adapter manage whether the ABTS is sent to not.
The issue is the unsol version is sending ABTS unconditionally for the
exchange that received the ABTS. It's unnecessary.
Remove the conditional and just call the adapter command-based routine to
let the adapter manage the ABTS.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of firmware download, the adapter is reset. On the adapter the
reset causes the function to stop and all outstanding io is terminated
(without responses). The reset path then starts teardown of the adapter,
starting with deregistration of the remote ports with the nvme-fc
transport. The local port is then deregistered and the driver waits for
local port deregistration. This never finishes.
The remote port deregistrations terminated the nvme controllers, causing
them to send aborts for all the outstanding io. The aborts were serviced in
the driver, but stalled due to its state. The nvme layer then stops to
reclaim it's outstanding io before continuing. The io must be returned
before the reset on the controller is deemed complete and the controller
delete performed. The remote port deregistration won't complete until all
the controllers are terminated. And the local port deregistration won't
complete until all controllers and remote ports are terminated. Thus things
hang.
The issue is the reset which stopped the adapter also stopped all the
responses that would drive i/o completions, and the aborts were also
stopped that stopped i/o completions. The driver, when resetting the
adapter like this, needs to be generating the completions as part of the
adapter reset so that I/O complete (in error), and any aborts are not
queued.
Fix by adding flush routines whenever the adapter port has been reset or
discovered in error. The flush routines will generate the completions for
the scsi and nvme outstanding io. The abort ios, if waiting, will be caught
and flushed as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This issue is specific to SLI-3 adapters, specifically when DIF is used.
Once seen, this message floods the logs:
9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from
dma_map_sg
The driver, upon detecting an error such as too many elements in an sglist,
misrepresents the error by treating it as a temporary resource issue by
returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it
should have been a hard error. The repeated retry was causing the spamming
of the log.
As for the initial reason of why an I/O encountered this issue at all is
not clear as parameters set by the driver should have avoided this. The
dm multipath maintainer has been notified of the issue.
Fix by changing the return code for the dma mapping routines to indicate
cases that are not retryable and return DID_ERROR on those cases.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During cable pull testing a deadlock was seen between lpfc_nlp_counters()
vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all
waiting on the shost->host_lock.
Issue is all of these cases raise irq when taking out the lock but use
spin_unlock_irq() when unlocking. The unlock path is will unconditionally
re-enable interrupts in cases where irq state should be preserved. The
re-enablement allowed the other paths to execute which then causes the
deadlock.
Fix by converting the lock/unlock to irqsave/irqrestore.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a test with high nvme remote port counts connected via a multi-hop FC
switch config where switches were systematically reset (e.g. fabric
partitioning and re-establishment), the nvme remote ports would switch
addresses based on the switch reconfiguration events. The driver would get
into a situation where the nvme port changed address, PLOGI and PRLI would
succeed nvme transport registration occurred, but subsequent LS requests by
the nvme subsystem failed due to a bad ndlp state and connectivity to the
device failed.
The driver hit a race condition on multiple devices that address swapped
simultaneously. In cases where the driver notices the remote port structure
came back as the same value as previously (meaning a nvme_rport structure
was re-enabled and did not go through devloss_tmo/connect_tmo_failures on
all controllers) the driver would unconditionally exit assuming the ndlp
information was correct. But, if the ndlp's had been swapped, the ndlp had
stale port state information, which when used by the LS request commands,
would fail the commands.
Fix by checking whether a node swap had occurred, and only exit if no ndlp
swap had occurred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In situations where zoning is not being used, thus NVMe initiators see
other NVMe initiators as well as NVMe targets, a link bounce on an
initiator will cause the NVMe initiators to spew "6169" State Error
messages.
The driver is not qualifying whether the remote port is a NVMe targer or
not before calling the lpfc_nvme_rescan_port(), which validates the role
and prints the message if its only an NVMe initiator.
Fix by the following:
- Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe
storage target or a NVMe discovery controller.
- Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer
will always be NULL if a NVMe initiator only. But, grabbing of
remoteport pointer should be done under lock to coincide with the
registering of the remote port with the fc transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a remote port is removed and remains removed for devloss_tmo, if an RSCN
is subsequently received indicating the presence of the remte port, the
driver does not login to and rediscovery the remote port.
Currently, in order to for a port to be rediscovered post an RSCN, the node
state must be NPR to reflect not logged in. When devloss expires, the node
state is marked UNUSED. When an RSCN occurs, the nodes referenced by the
RSCN will have a NPR_2B_DISC flag set, but the re-login will only be
attempted if the node is in NPR_NODE state. Thus the node is skipped over.
Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back
to NPR state to allow the re-login to take place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the driver to initiate an FLOGI and before it completes,
another link down/up transition occurs requiring a new FLOGI. Currently,
nothing is done to abort/noop the older FLOGI request to the adapter, so if
this transition occurs and the FLOGI completion is received after the link
down/up transition, the driver may erroneously act on the older FLOGI. In
most cases, the adapter properly terminates/fails the FLOGI, but there is a
timing condition where the FLOGI may complete on the wire prior to the
transition, but the response may not be seen/processed by the driver before
the driver sees the link transition.
Fix by having the link down handler in the driver run through any
outstanding ELS's and change the completion handler of the ELS so that it
will be no-op'd and released.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When tearing down the adapter for a reset, online/offline, or driver
unload, the queue free routine would hit a GPF oops. This only occurs on
conditions where the number of hardware queues created is fewer than the
number of cpus in the system. In this condition cpus share a hardware
queue. And of course, it's the 2nd cpu that shares a hardware that
attempted to free it a second time and hit the oops.
Fix by reworking the cpu to hardware queue mapping such that:
Assignment of hardware queues to cpus occur in two passes:
first pass: is first time assignment of a hardware queue to a cpu.
This will set the LPFC_CPU_FIRST_IRQ flag for the cpu.
second pass: for cpus that did not get a hardware queue they will
be assigned one from a primary cpu (one set in first pass).
Deletion of hardware queues is driven by cpu itteration, and queues
will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set.
Also contains a few small cleanup fixes and a little better logging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_register_port hit a null prev_ndlp pointer in a test with lots of
target ports swapping addresses. The oldport value was stale, thus it's
ndlp (prev_ndlp set to it) was used.
Fix by moving oldrport pointer checks, and if used prev_ndlp pointer
assignment, to be done while the lock is held.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is inadvertently trying to issue an INIT_VPI mailbox command on
an SLI-3 driver. The command is specific to SLI-4. When the call is made to
send the command, if on an SLI-3 adapter, an array pointer is NULL and the
driver will oops.
Fix by restricting the command to SLI-4 adapters only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unusually high IO latency can be observed with little IO in progress. The
latency may remain high regardless of amount of IO and can only be cleared
by forcing lpfc_fcp_imax values to non-zero and then back to zero.
The driver's eq_delay mechanism that scales the interrupt coalescing based
on io completion load failed to reduce or turn off coalescing when load
decreased. Specifically, if no io completed on a cpu within an eq_delay
polling window, the eq delay processing was skipped and no change was made
to the coalescing values. This left the coalescing values set when they
were no longer applicable.
Fix by always clearing the percpu counters for each time period and always
run the eq_delay calculations if an eq has a non-zero coalescing value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a timer routine uses workqueues, it could fire before the workqueue is
allocated.
Fix by allocating the workqueue before the timer routines are setup
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After seeing some interoperability issues with ADISC, it was determined the
ELS definitions in lpfc were using types that allowed the compiler to add
pad to the structure, causing the structure to no longer be per spec. The
offending structures are ADISC, FAN, and RNID.
This patch implements the simple fix of eliminating the pad by forcing the
compiler to pack the structure. Care was taken to ensure field accesses
won't be by operations that would hit a bad field alignment.
The better solution would be to convert to the uapi fc header definitions,
but the number of changes required to do is rather intrusive so this course
of action was deferred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi-mq operation inherently performs pre-allocation of resources for
blk-mq request queues. Even though the kdump environment reduces the
configuration to a single CPU, thus 1 hardware queue, which helps
significantly, the resources are still rather large due to the per request
allocations. blk-mq pre-allocations can be over 4KB per request. With
adapter can_queue values in the 4k or 8k range, this can easily be 32MBs
before any other driver memory is factored in. Driver SGL DMA buffer
allocation can be up to 8KB per request as well adding an additional
64MB. Totals are well over 100MB for a single shost. Given kdump memory
auto-sizing utilities don't accommodate this amount of memory well, it's
very possible for kdump to fail due to lack of memory.
Fix by having the driver recognize that it is booting within a kdump
context and reduce the number of requests it will support to a more
reasonable value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Static structure ufs_hba_qcom_vops, of type ufs_hba_variant_ops, is used
only once, when it is passed as the second argument to function
ufshcd_pltfrm_init(). In the definition of ufshcd_pltfrm_init(), its second
parameter (corresponding to ufs_hba_qcom_vops) is declared as
constant. Hence declare ufs_hba_qcom_vops itself constant as well to
protect it from unintended modification. Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable ret is initialized to a value that is never read and it is
re-assigned later and immediately returns. Clean up the code by removing
rc and just returning 0.
[mkp: typo]
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid code duplication between qla2x00_alloc_offload_mem() and
qla2x00_alloc_fw_dump() by moving the FCE and EFT buffer allocation and
initialization to separate functions. Cleanly track failure and success by
making sure that the ha->eft, ha->fce and respective eft_dma, fce_dma
members are set if and only if the buffers are properly allocated and
initialized. Avoid pointless buffer reallocation. Eliminate some goto
statements. Make sure the fce_enabled flag is cleared when the FCE buffer
is freed.
Fixes: ad0a0b01f0 ("scsi: qla2xxx: Fix Firmware dump size for Extended login and Exchange Offload")
Fixes: a28d9e4ef9 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In qla2x00_alloc_fw_dump(), an existing EFT buffer (e.g. from previous
invocation of qla2x00_alloc_offload_mem()) is freed. The buffer is then
re-allocated, but without setting the eft and eft_dma fields to the new
values.
Fixes: a28d9e4ef9 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SGI SN2 support is about to be removed, so drop the bits specific to
it from this driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-13-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed, so drop the bits specific to
it from this driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-12-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the following BUG:
[ 187.065689] BUG: kernel NULL pointer dereference, address: 000000000000001c
[ 187.065790] RIP: 0010:ufshcd_vreg_set_hpm+0x3c/0x110 [ufshcd_core]
[ 187.065938] Call Trace:
[ 187.065959] ufshcd_resume+0x72/0x290 [ufshcd_core]
[ 187.065980] ufshcd_system_resume+0x54/0x140 [ufshcd_core]
[ 187.065993] ? pci_pm_restore+0xb0/0xb0
[ 187.066005] ufshcd_pci_resume+0x15/0x20 [ufshcd_pci]
[ 187.066017] pci_pm_thaw+0x4c/0x90
[ 187.066030] dpm_run_callback+0x5b/0x150
[ 187.066043] device_resume+0x11b/0x220
Voltage regulators are optional, so functions must check they exist
before dereferencing.
Note this issue is hidden if CONFIG_REGULATORS is not set, because the
offending code is optimised away.
Notes for stable:
The issue first appears in commit 57d104c153 ("ufs: add UFS power
management support") but is inadvertently fixed in commit 60f0187031
("scsi: ufs: disable vccq if it's not needed by UFS device") which in
turn was reverted by commit 730679817d ("Revert "scsi: ufs: disable vccq
if it's not needed by UFS device""). So fix applies v3.18 to v4.5 and
v5.1+
Fixes: 57d104c153 ("ufs: add UFS power management support")
Fixes: 730679817d ("Revert "scsi: ufs: disable vccq if it's not needed by UFS device"")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If HBA initialization fails unexpectedly (exiting via probe_failed:), we
may fail to free vha->gnl.l. So that we don't attempt to double free, set
this pointer to NULL after a free and check for NULL at probe_failed: so we
know whether or not to call dma_free_coherent.
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Single lpfc fix, for a single cpu corner case.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXVKNpSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishcBWAQDV2FTB
Day/5EVD/hwtXNNaA2ygzy/Vi8QgNV0xqQOzRQD/cVoh8fMCqlV1yVqrvMikJRp4
Zrbnvhe0k4cGhdD8Dcg=
=Jpj2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Single lpfc fix, for a single-cpu corner case"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Fix crash when cpu count is 1 and null irq affinity mask
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable retv is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke
Saurav Kashyap
Nilesh Javali
Arun Easi
Don Brace
Gilbert Wu
Murthy Bhat
Mahesh Rajashekhara
Dave Carroll
James Smart
zhengbin
Colin Ian King
Sreekanth Reddy
Bart Van Assche
Stanley Chu
Anil Varughese
Krzysztof Wilczynski
David S. Miller
Linus Torvalds
Gustavo A. R. Silva
Hariprasad Kelam
Nishka Dasgupta
Fuqian Huang
Martin Wilck
Christoph Hellwig
Adrian Hunter
Bill Kuzeja
Frederick Lawler