BDX-DE IOATDMA reports incorrect DMACAP register for PQ related
ops. Ignoring those bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When simplificating the channel configuration, the cyclic case has been
forgotten. It leads to use bad configuration causing many bugs.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When dma controller is not used by any user and set off,
we should disble interrupt handler, at least the interrupt
reset part, for some subsystem, e.g. ADSP, may use the
dma in its own logic, here reset the interrupt may make
this subsystem work abnormally.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Below are the refinements.
1. Set DMA abort bit when disabling dma channel. This will clear
the remaining data in dma FIFO, to fix channel-swap issue.
2. Read DMA HW pointer when updating DMA status. Previously dma
position is calculated by adding one period size in dma interrupt.
This is inaccurate/insufficient for some high-quality audio APP.
Since interrupt bottom half handler has variable schedule delay,
it causes big error when calculating sample delay. Read the actual
HW pointer and feedback can improve the accuracy.
3. Do some minor code clean.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix spelling mistake, "aquire" -> "acquire" and missing newline (as
spotted by Joe Perches.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During system reboot, the sh-dma-engine device may be runtime-suspended,
causing a crash:
Unhandled fault: imprecise external abort (0x1406) at 0x0002c02c
Internal error: : 1406 [#1] SMP ARM
...
PC is at sh_dmae_ctl_stop+0x28/0x64
LR is at sh_dmae_ctl_stop+0x24/0x64
If the sh-dma-engine is runtime-suspended, its module clock is turned
off, and its registers cannot be accessed.
To fix this, move the call to sh_dmae_ctl_stop(), which touches the
DMAOR register, to the sh_dmae_suspend() and sh_dmae_runtime_suspend()
callbacks. This makes PM operations more symmetric, as both
sh_dmae_resume() and sh_dmae_runtime_resume() already call sh_dmae_rst()
to re-initialize the DMAOR register.
Remove sh_dmae_shutdown(), as it became empty.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes checkpatch.pl error in file ste_dma40.c
ERROR: space required before the open parenthesis '('
Signed-off-by: Dilek Uzulmez <dilekuzulmez@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some dma channels may be reserved for other purpose in other layer,
like secure driver in EL2/EL3. PDMA driver can see the interrupt
status, but it should not try to handle related interrupt, since it
doesn't belong to PDMA driver in kernel. These interrupts should be
handled by corresponding client/module.Otherwise, it will overwrite
illegal memory and cause unexpected issues, since pdma driver only
requests resources for pdma channels.
In PDMA driver, the reserved channels are at the end of total 32
channels. If we find interrupt bit index is not smaller than total
dma channels, we should ignore it.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calls tasklet_kill() in error path of the probe function were missing.
Add the same in error path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
in dma_slave_config, which is incompatible with the way that the
dmaengine API normally works.
I've had a closer look at the existing code now and found that all
slave drivers that pass a slave_id in dma_slave_config for SH do that
right after passing the same ID into shdma_chan_filter, so we can just
rely on that. However, the various shdma drivers currently do not
remember the slave ID that was passed into the filter function when
used in non-DT mode and only check the value to find a matching channel,
unlike all other drivers.
There might still be drivers that are not part of the kernel that rely
on setting the slave_id to some other value, so to be on the safe side,
this adds another 'real_slave_id' field to shdma_chan that remembers
the ID and uses it when a driver passes a zero slave_id in dma_slave_config,
like most drivers do.
Eventually, the real_slave_id and slave_id fields should just get merged
into one field, but that requires other changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
DMA_PAUSE command is used for halting DMA transfer on chosen channel.
It can be useful when we want to safely read residue before terminating
all requests on channel. Otherwise there can be situation when some data
is transferred before channel termination but after reading residue,
which obviously results with data loss. To avoid this situation we can
pause channel, read residue and then terminate all requests.
This scenario is common, for example, in serial port drivers.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds possibility to read residue of DMA transfer. It's useful
when we want to know how many bytes have been transferred before we
terminate channel. It can take place, for example, on timeout interrupt.
Signed-off-by: Lukasz Czerwinski <l.czerwinski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A still unconfirmed hardware bug prevents the IPMMU microTLB 0 to be
flushed correctly, resulting in memory corruption. DMAC 0 channel 0 is
connected to microTLB 0 on currently supported platforms, so we can't
use it with the IPMMU. As the IOMMU API operates at the device level we
can't disable it selectively, so ignore channel 0 for now if the device
is part of an IOMMU group.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When descriptor memory is accessed through an IOMMU the DMADAR register
isn't initialized automatically from the first descriptor at beginning
of transfer by the DMAC like it should. Initialize it manually with the
destination address of the first chunk.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When wired to an IOMMU to access data, the DMAC accesses the hardware
descriptors through the IOMMU as well. We're using the DMA mapping API
to allocate the descriptors, but with a NULL device at the moment, which
prevents IOMMU mappings from being created. Fix this by passing the DMAC
device instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The error interrupt handler stops and reinitializes all channels. This
causes a crash for channels that have never been used, as their
descriptor lists are uninitialized. Fix it by initializing the
descriptor lists at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The rcar_dmac_desc_put() function is called in interrupt context and
must thus use spin_lock_irqsave() instead of spin_lock_irq().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch fixes following sparse warnings:
edma.c:537:32: warning: symbol 'edma_prep_dma_memcpy' was not declared. Should it be static?
edma.c:1070:6: warning: symbol 'edma_filter_fn' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The desc variable is used uninitialized in the rcar_dmac_desc_get() and
rcar_dmac_xfer_chunk_get() functions if descriptors need to be
allocated. Fix it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sh_dmae_{suspend|resume}() for the {freeze|
thaw|restore}() PM methods. It's handy to achieve this with SIMPLE_DEV_PM_OPS()
macro; since that macro doesn't do anything when CONFIG_PM_SLEEP is undefined,
we don't need to #define sh_dmae_{suspend|resume} NULL anymore but we'll have to
enclose sh_dmae_{suspend|resume}() into the new #ifdef...
Based on original patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use SET_RUNTIME_PM_OPS() to initialize the runtime PM method pointers in the
'struct dev_pm_ops'; since that macro doesn't do anything if CONFIG_PM is
not defined, we have to move #ifdef up to also cover the runtime PM methods
in order to avoid compilation warnings.
Based on orignal patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently ACPI, PCI and pnp all implement the same resource list
management with different data structure. We need to transfer from
one data structure into another when passing resources from one
subsystem into another subsystem. So move struct resource_list_entry
from ACPI into resource core and rename it as resource_entry,
then it could be reused by different subystems and avoid the data
structure conversion.
Introduce dedicated header file resource_ext.h instead of embedding
it into ioport.h to avoid header file inclusion order issues.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When using FIFO, we need to support differents data width in a single
transfer. For example, serial device which usually uses 1-byte data
width will use 4-bytes data width when using the FIFO. If the transfer
size is not aligned on 4-bytes then the end of the transfer will be
performed with 1-byte data-width. For that reason,
at_xdmac_prep_slave_sg() now builds linked list descriptors using view 2
instead of view 1 so each of them can update the DWIDTH field into the
Channel Configuration Register.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch simplifies the channel configuration register management.
Relying on a "software snapshot" of the configuration is not safe and
too complex.
Multiple dwidths will be introduced for slave transfers. In this case,
it becomes quite difficult to have an accurate snapshot of the channel
configuration register in the way it is done. Using the channel
configuration available in the lli descriptor simplifies this stuff.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When suspending the device, read the channel configuration directly from
the register instead of relying on a software snapshot, it will be
safer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
wait_for_completion_timeout reaching timeout was being ignored,
fail the self-test if timeout condition occurs.
v2: fixup of coding style issues.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of using magic number in the code the patch provides
DW_DMA_MAX_NR_MASTERS constant.
While here, restrict the reading of data width array by amount of the actual
number of AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The scope of those varsiables is in while-loop. This patch moves them there and
removes duplicate code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simple fixes an indentation in few places across the code.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for the IMG Multi-threaded DMA Controller (MDC) found on
certain IMG SoCs. Currently this driver supports the variant present
on the MIPS-based Pistachio SoC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should unlock here before returning -EINVAL.
Fixes: 39ad460096 ('dmaengine: s3c24xx: Split device_control')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding PCI device IDs and hooks in workarounds for Broadwell DE ioatdma.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
And don't print an error: not configured is not an error.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ecc19d1786
(dmaengine: Add a warning for drivers not using the generic slave
caps retrieval) added WARN() for DMA_SLAVE.
Kernel will shows WARNING without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver doesn't support residue reporting at all.
residue_granularity should be set to DMA_RESIDUE_GRANULARITY_DESCRIPTOR.
Special thanks to Laurent
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Everything uses dmaengine now, so there is no reason to
keep this around any longer. Thanks to everyone who was involved
in moving the users over to use the dmaengine APIs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
A recent patch that removed coh901318_control() replaced it
with a number of pointers to existing functions, but those
unfortunately have the wrong return type and need to be
changed to return an 'int' with an error value rather than
a 'void' to avoid these build warnings:
drivers/dma/coh901318.c:2697:32: warning: assignment from incompatible pointer type
base->dma_slave.device_config = coh901318_dma_set_runtimeconfig;
^
drivers/dma/coh901318.c:2698:31: warning: assignment from incompatible pointer type
base->dma_slave.device_pause = coh901318_pause;
^
drivers/dma/coh901318.c:2699:32: warning: assignment from incompatible pointer type
base->dma_slave.device_resume = coh901318_resume
The coh901318_base_init function has the correct return type
already, but needs to be marked 'static' to avoid a sparse
warning about a missing declaration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6782af118b ("dmaengine: coh901318: Split device_control")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A typo has been introduced in the spin_unlock_irqrestore function. Fix it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sa11x0_dma_resume conflicts between the dmaengine device_resume callback
and the dev_pm_ops resume implementation.
Also remove some unused variables at the same time.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The function is too big to be a static inline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After commit ecc19d1786 ("dmaengine: Add
a warning for drivers not using the generic slave caps retrieval"),
the Tegra APB DMA driver causes this warning during boot:
WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:830 dma_async_device_register+0x294/0x538()
this driver doesn't support generic slave capabilities reporting
Fix by setting the appropriate reporting structure fields that are
passed to dma_async_device_register().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the following build warning:
drivers/dma/fsldma.c: In function 'fsl_dma_device_terminate_all':
drivers/dma/fsldma.c:947:6: warning: unused variable 'size' [-Wunused-variable]
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ecc19d1786
(dmaengine: Add a warning for drivers not using the generic slave
caps retrieval) added WARN() for DMA_SLAVE.
Kernel will shows WARNING without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to return a 'fake' value upon platform_get_irq() failure.
Just propagate the real error instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
By using devm functions we can make the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since ecc19d1786 ("dmaengine: Add a warning for drivers not using the
generic slave caps retrieval") the following warning is observed:
[ 0.224981] ------------[ cut here ]------------
[ 0.225013] WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:830 dma_async_device_register+0x2a0/0x4c8()
[ 0.225023] this driver doesn't support generic slave capabilities reporting
Declare the slave capabilities to avoid such warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since ecc19d1786 ("dmaengine: Add a warning for drivers not using the
generic slave caps retrieval") the following warning is observed:
[ 0.113023] ------------[ cut here ]------------
[ 0.113053] WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:830 dma_async_device_register+0x2a0/0x4c8()
[ 0.113063] this driver doesn't support generic slave capabilities reporting
Declare the slave capabilities to avoid such warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The new DMAEngine requirement is to provide what the DMA controller can do,
such as directions, bus widths, and residue granularity. The patch sets those
properties for the DesignWare DMA controller driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of PCI driver we will get a warning:
dw_dmac_pci 0000:00:18.0: Unbalanced pm_runtime_enable!
dw_dmac_pci 0000:00:18.0: DesignWare DMA Controller, 8 channels
This happens due to pm_runtime_enable() call from the driver when PM runtime is
enabled by core.
This patch moves that call to the platform driver where it might make sense.
Fixes: bb32baf76e (dmaengine: dw: enable runtime PM)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In a recent cleanup, the mmp_tdma_terminate_all function was
introduced but does not set a proper return value. Almost
no slave driver uses that return value, but if one does, the
result will be undefined, which the compiler warns about:
dma/mmp_tdma.c: In function 'mmp_tdma_terminate_all':
dma/mmp_tdma.c:474:1: warning: no return statement in function returning non-void [-Wreturn-type]
This changes the driver to return zero, like most other
drivers do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f43a6fd400 ("dmaengine: mmp-tdma: Split device_control")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mmp tdma driver does not actually require this header, and
we want to enable multiplatform support for MMP, which would
make it inaccessible and cause a build error.
This patch just removes the old #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit db08425ebd ("dmaengine: k3: Split device_control") introduced
two new helper functions, which unfortunately have the same names
as the existing suspend/resume functions, resulting in a build error
when CONFIG_PM_SLEEP is enabled:
drivers/dma/k3dma.c:823:12: error: conflicting types for 'k3_dma_resume'
static int k3_dma_resume(struct device *dev)
^
drivers/dma/k3dma.c:625:12: note: previous definition of 'k3_dma_resume' was here
static int k3_dma_resume(struct dma_chan *chan)
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: db08425ebd ("dmaengine: k3: Split device_control")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While splitting device control in db08425ebd ("dmaengine: k3:
Split device_control") new function with the same 'k3_dma_resume' name
was added, leading to build error:
drivers/dma/k3dma.c:823:12: error: conflicting types for ‘k3_dma_resume’
drivers/dma/k3dma.c:625:12: note: previous definition of ‘k3_dma_resume’ was here
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the atomic DMA coherent pool is too small, disable use of hardware
descriptor lists instead of crashing the system:
ERROR: 256 KiB atomic DMA coherent pool is too small!
Please increase it with coherent_pool= kernel parameter!
Unable to handle kernel NULL pointer dereference at virtual address 00000004
Internal error: Oops: a07 [#1] PREEMPT SMP ARM
PC is at rcar_dmac_chan_reinit+0x3c/0x160
LR is at _raw_spin_lock_irqsave+0x18/0x5c
[<802132c0>] (rcar_dmac_chan_reinit) from [<80214818>] (rcar_dmac_isr_error+0x84/0xa0)
[<80214818>] (rcar_dmac_isr_error) from [<80060484>] (handle_irq_event_percpu+0x50/0x150)
[<80060484>] (handle_irq_event_percpu) from [<800605c0>] (handle_irq_event+0x3c/0x5c)
[<800605c0>] (handle_irq_event) from [<8006350c>] (handle_fasteoi_irq+0xb8/0x198)
[<8006350c>] (handle_fasteoi_irq) from [<8005fdb0>] (generic_handle_irq+0x20/0x30)
[<8005fdb0>] (generic_handle_irq) from [<8000fcd0>] (handle_IRQ+0x50/0xc4)
[<8000fcd0>] (handle_IRQ) from [<800092cc>] (gic_handle_irq+0x28/0x5c)
[<800092cc>] (gic_handle_irq) from [<80012700>] (__irq_svc+0x40/0x70)
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Unlike DMA transfers descriptors that are preallocated and cached,
memory used to store hardware descriptors is allocated and freed with
the DMA coherent allocation API for every transfer. Besides degrading
performances, this creates a CMA stress test that seems to cause issues.
Running dmatest with the noverify option produces
[ 50.066539] alloc_contig_range test_pages_isolated(6b845, 6b846) failed
[ 50.235180] alloc_contig_range test_pages_isolated(6b848, 6b84e) failed
[ 52.964584] alloc_contig_range test_pages_isolated(6b847, 6b848) failed
[ 54.127113] alloc_contig_range test_pages_isolated(6b843, 6b844) failed
[ 56.270253] alloc_contig_range test_pages_isolated(6b84c, 6b850) failed
The root cause needs to be fixed, but in the meantime, as a workaround
and a performance improvement, cache hardware descriptors.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The DMAC supports hardware-based auto-configuration from descriptor
lists. This reduces the number of interrupts required for processing a
DMA transfer. Support that mode in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The DMAC is a general purpose multi-channel DMA controller that supports
both slave and memcpy transfers.
The driver currently supports the DMAC found in the r8a7790 and r8a7791
SoCs. Support for compatible DMA controllers (such as the audio DMAC)
will be added later.
Feature-wise, automatic hardware handling of descriptors chains isn't
supported yet. LPAE support is implemented.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Remove the function is_imx21_dma() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/tegra20-apb-dma.c:1428:37: warning: assignment from incompatible pointer type [enabled by default]
drivers/dma/ste_dma40.c: In function 'd40_terminate_all':
The function prototype expects return type 'int' whereas these where void
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/ste_dma40.c:2627:3: warning: 'return' with a value, in function returning void [enabled by default]
drivers/dma/ste_dma40.c: In function 'd40_ops_init':
drivers/dma/ste_dma40.c:2869:28: warning: assignment from incompatible pointer type [enabled by default]
The function prototype expects return type 'int' whereas these where void
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/mxs-dma.c: In function 'mxs_dma_probe':
drivers/dma/mxs-dma.c:848:35: warning: assignment from incompatible pointer type [enabled by default]
drivers/dma/mxs-dma.c:849:36: warning: assignment from incompatible pointer type [enabled by default]
The function prototype expects return type 'int' whereas these where void
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mxs_dma_reset_chan() expects struct dma_chan * as argument but we were
providing struct dma_chan, so fix this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For the slave caps retrieval to be really useful, most drivers need to
implement it.
Hence, we need to be slightly more aggressive, and trigger a warning at
registration time for drivers that don't fill their caps infos in order to
encourage them to implement it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that the generic slave caps code can make use of the device assigned
capabilities, instead of relying on a callback to be implemented.
Make use of this code.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename the device_control callback of the TXX9 DMA driver to terminate_all
since it's all it's really doing. That will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename the device_control callback of the Timberdal DMA driver to terminate_all
since it's all it's really doing. That will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename the device_control callback of the Intel PCH DMA driver to terminate_all
since it's all it's really doing. That will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Marvell XOR engine doesn't allow any operations that use to be defined in
device_control, it shouldn't need to be defined. Since it's going to be
deprecated, remove it altogether.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Xilinx VDMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the NVidia Tegra20 APB DMA driver to make
use of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the ST-Ericsson DMA 40 driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Allwinner A31 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the SiRF Prima 2 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Super-H DMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the SA-11x0 DMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Samsung S3C24xxx DMA driver to make
use of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Qualcomm BAM DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the AMBA PL330 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the TI OMAP DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the NBPF AXI DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale MXS DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale MPC512x DMA driver to make
use of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale Elo DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
While we're at it, remove the useless prep_sg callback.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Moxart DMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Marvell MMP TDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Marvell MMP PDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Hisilicon K3 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the IPU IDMAC driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Intel MID DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale IMX SDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale IMX DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale EDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Cirrus Logic EP93xx driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the TI EDMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the DesignWare DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the JZ4740 DMA driver to make use of the
newly introduced callbacks, that will eventually be used to retrieve slave
capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the TI CPPI41 DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the ST-Ericsson COH901318 DMA driver to
make use of the newly introduced callbacks, that will eventually be used to
retrieve slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Broadcom BCM2835 DMA driver to make
use of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Atmel HDMAC driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the AMBA PL08x DMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to migrate the drivers without triggering a BUG_ON for the converted
drivers, which would cause bisectability issues, we need to remove that check
before removing the device_control function entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Nowadays, some drivers don't have anything in there channel allocation
callbacks anymore.
Remove the BUG_ON if those callbacks aren't implemented, in order to allow
drivers to not implement them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_chan_get uses a rather interesting error handling and code path.
Change it to something more usual in the kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dmaengine header abbreviates destination as at least two different strings.
Make a coherent use of a single one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The err completion callback is missing from the error handler. Two
reasons we never hit this. On Xeon because the hw err workaround, the
completion happens on a NULL descriptor so we don't do callback on the
PQ descriptor. On Atom we have DWBES support and thus the callback already
happened or we don't halt on error, so that was take cared of. But this code
needs to be corrected for future error handlers.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fixed a coding style error, switch and case should be at the same indent
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull ARM updates from Russell King:
"The major updates included in this update are:
- Clang compatible stack pointer accesses by Behan Webster.
- SA11x0 updates from Dmitry Eremin-Solenikov.
- kgdb handling of breakpoints with read-only text/modules
- Support for Privileged-no-execute feature on ARMv7 to prevent
userspace code execution by the kernel.
- AMBA primecell bus handling of irq-safe runtime PM
- Unwinding support for memset/memzero/memmove/memcpy functions
- VFP fixes for Krait CPUs and improvements in detecting the VFP
architecture
- A number of code cleanups (using pr_*, removing or reducing the
severity of a couple of kernel messages, splitting ftrace asm code
out to a separate file, etc.)
- Add machine name to stack dump output"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (62 commits)
ARM: 8247/2: pcmcia: sa1100: make use of device clock
ARM: 8246/2: pcmcia: sa1111: provide device clock
ARM: 8245/1: pcmcia: soc-common: enable/disable socket clocks
ARM: 8244/1: fbdev: sa1100fb: make use of device clock
ARM: 8243/1: sa1100: add a clock alias for sa1111 pcmcia device
ARM: 8242/1: sa1100: add cpu clock
ARM: 8221/1: PJ4: allow building in Thumb-2 mode
ARM: 8234/1: sa1100: reorder IRQ handling code
ARM: 8233/1: sa1100: switch to hwirq usage
ARM: 8232/1: sa1100: merge GPIO multiplexer IRQ to "normal" irq domain
ARM: 8231/1: sa1100: introduce irqdomains support
ARM: 8230/1: sa1100: shift IRQs by one
ARM: 8229/1: sa1100: replace irq numbers with names in irq driver
ARM: 8228/1: sa1100: drop entry-macro.S
ARM: 8227/1: sa1100: switch to MULTI_IRQ_HANDLER
ARM: 8241/1: Update processor_modes for hyp and monitor mode
ARM: 8240/1: MCPM: document mcpm_sync_init()
ARM: 8239/1: Introduce {set,clear}_pte_bit
ARM: 8238/1: mm: Refine set_memory_* functions
ARM: 8237/1: fix flush_pfn_alias
...
Pull dmaengine updates from Vinod Koul:
"Main features this time are:
- BAM v1.3.0 support form qcom bam dma
- support for Allwinner sun8i dma
- atmels eXtended DMA Controller driver
- chancnt cleanup by Maxime
- fixes spread over drivers"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (56 commits)
dmaenegine: Delete a check before free_percpu()
dmaengine: ioatdma: fix dma mapping errors
dma: cppi41: add a delay while setting the TD bit
dma: cppi41: wait longer for the HW to return the descriptor
dmaengine: fsl-edma: fixup reg offset and hw S/G support in big-endian model
dmaengine: fsl-edma: fix calculation of remaining bytes
drivers/dma/pch_dma: declare pch_dma_id_table as static
dmaengine: ste_dma40: fix error return code
dma: imx-sdma: clarify about firmware not found error
Documentation: devicetree: Fix Xilinx VDMA specification
dmaengine: pl330: update author info
dmaengine: clarify the issue_pending expectations
dmaengine: at_xdmac: Add DMA_PRIVATE
ARM: dts: at_xdmac: fix bad value of dma-cells in documentation
dmaengine: at_xdmac: fix missing spin_unlock
dmaengine: at_xdmac: fix a bug in transfer residue computation
dmaengine: at_xdmac: fix software lockup at_xdmac_tx_status()
dmaengine: at_xdmac: remove chancnt affectation
dmaengine: at_xdmac: prefer usage of readl/writel_relaxed
dmaengine: xdmac: fix print warning on dma_addr_t variable
...
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
The free_percpu() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The manual says that we need to (repeatedly) set the TearDown-bit for
the endpoint in order to get the active transfer descriptor released.
Doing this "real" quick over and over again seems to work but it also
seems that the hardware might not have enough time to breathe. So I
though, hey lets add a udelay() between between the individual sets
of the bit.
This change with the g_zero testcase resulted in a warning about missing
transfer descriptor (we got the tear-down one). It seems that if the
hardware has some time it manages to release the transfer-descriptor on
the completion queue after the teaddown descriptor.
With this change, I observe that the transfer descriptor is released
after 20-30 retry loops.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For a "complete" teardown we have to wait until the teardown descriptor
is returned by the hardware. The g_zero testcase "testusb -a -t 9" triggers
the following warning quite reliable:
|------------[ cut here ]------------
|WARNING: CPU: 0 PID: 0 at drivers/dma/cppi41.c:609 cppi41_dma_control+0x198/0x304()
|[<c003f84c>] (warn_slowpath_null) from [<c02be8d8>]
|[<c02be8d8>] (cppi41_dma_control) from [<bf08d25c>]
|[<bf08d25c>] (cppi41_dma_channel_abort [musb_hdrc])
|[<bf08bc38>] (nuke.constprop.10 [musb_hdrc])
|[<bf08bd08>] (musb_gadget_disable [musb_hdrc])
|[<bf252524>] (disable_endpoints [usb_f_ss_lb])
|[<bf2525d8>] (disable_source_sink [usb_f_ss_lb])
|[<bf25260c>] (sourcesink_set_alt [usb_f_ss_lb])
|[<bf23ad24>] (composite_setup [libcomposite])
|[<bf08a2f4>] (musb_g_ep0_irq [musb_hdrc])
|[<bf085ec4>] (musb_interrupt [musb_hdrc])
|[<bf0aeaf4>] (dsps_interrupt [musb_dsps])
|[<c0080ea8>] (handle_irq_event_percpu)
|[<c008112c>] (handle_irq_event)
|[<c008348c>] (handle_level_irq)
|[<c00807a8>] (generic_handle_irq)
|[<c000ee80>] (handle_IRQ)
|[<c00085f0>] (omap3_intc_handle_irq)
and complains about a TD descriptor which is not returned. I've been
looking at several things and haven't noticed anything unusual that
might lead to this.
The manual says "to try again" until the descriptor comes out. I limited
the amount of retries to 100 retries in order to avoid an infinite number
of retries and so a busy-loop. Back then testing revealed that the
number of retries were around 20-30 so 100 seemed a good upper limit.
This g_zero test reaches without a problem 98 retries and it jumps
sometimes to 101 on am335x-evm and so the WARN_ON() triggers. Same test
run on beaglebone black and the retries start at 122 and my max value so
far was at 128.
So lets rise the limit to 500.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The offset of all 8-/16-bit registers in big-endian eDMA model are
swapped in a 32-bit size opposite those in the little-endian model.
The hardware Scatter/Gather requires the subsequent TCDs stored in memory
in little endian independent of the register endian model, the eDMA engine
will do the swap if need.
This patch also use regular assignment for tcd variables r/w
instead of with io function previously that may not always be true.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the current transfer control descriptor (TCD) was not yet started,
the address will be the same as the initial address. Hence test if the
current address is less than or equal to the start address of each TCD.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/dma/nbpfaxi.c
and drivers/dma/tegra20-apb-dma.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
pch_dma_id_table is used in pch_dma.c only, so declare
it as static
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When a firmware cannot be found for the SDMA engine then we can
continue with the internal ROM firmware.
The meaning of this message is frequently asked for, so make clear
that the driver still works with the internal ROM firmware and reduce
the loglevel from err to info.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Update email-id to a personal one, as I have changed employment.
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add system suspend/resume capabilities to the pl330 driver so the amba
bus clock could be also unprepared to conserve energy.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull dmaengine fixes from Vinod Koul:
"We have couple of fixes for dmaengine queued up:
- dma mempcy fix for dma configuration of sun6i by Maxime
- pl330 fixes: First the fixing allocation for data buffers by Liviu
and then Jon's fixe for fifo width and usage"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: Fix allocation size for PL330 data buffer depth.
dmaengine: pl330: Limit MFIFO usage for memcpy to avoid exhausting entries
dmaengine: pl330: Align DMA memcpy operations to MFIFO width
dmaengine: sun6i: Fix memcpy operation
This patch adds runtime PM support to pl330 DMA engine driver.
The runtime power management for pl330 DMA driver allows gating of AMBA
clock (PDMA) in FSYS clock domain, when the device is not processing any
requests. This is necessary to enter low power modes on Exynos SoCs
(e.g. LPA on Exynos4x12 or W-AFTR on Exynos3250).
Runtime PM resuming of the device may happen in atomic context (during
call device_issue_pending()) so pm_runtime_irq_safe() is used. This will
lead only to disabling/enabling of the clock but this is sufficient for
gating the clock and for reducing energy usage.
Driver uses runtime PM callbacks from amba/bus.c driver only.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
same issue as commit 7f5ae3553685:
"Without DMA_PRIVATE the driver is not able to allocate more than one channel.
Since it uses dma_get_any_slave_channel that calls private_candidate, the
second allocation fails at
/* some channels are already publicly allocated */
"
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Lock taken when entering the function but unlock missing before it
returns.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The total size of the transfer was wrong in at_xdmac_prep_slave_sg()
resulting in bad computation of the transfer residue by
at_xdmac_tx_status().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to the Atmel eXtended DMA controller datasheet, requesting a
DMA transfer flush for a channel is only revelant when this transfer is
source peripheral synchronized.
So we have to check this condition before requesting a channel flush by
writing the channel bit into the Global channel SoftWare Flush (GSWF)
register then waiting for flush to complete by monitoring the end of
Flush Interrupt Status (FIS) bit in the Channel Interrupt Status (CIS)
register.
Indeed, for non source peripheral synchronized transfer, writing the
channel bit into the GSWF register does nothing. Especially, the FIS bit
is never set into the CIS register. The former code looped forever
waiting for this bit to be set.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove chancnt affectation since it is done in dma_async_device_regiser.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
_relaxed version of readl and writel are not implemented on all
architecture so COMPILE_TEST has to be removed in order to not cause
some build failures.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As documented in printk-formats.txt the dma_addr_t should be printed with
%pad specfiers. This way it works on all archs.
make.cross ARCH=s390
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_slave_sg':
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:621:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:628:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: buf_addr=0x%08x, buf_len=%d, period_len=%d, dir=%s, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:690:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:709:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:716:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
>> drivers/dma/at_xdmac.c:731:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: src=0x%08x, dest=0x%08x, len=%d, flags=0x%lx\n",
^
>> drivers/dma/at_xdmac.c:765:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan), "%s: remaining_size=%u\n", __func__, remaining_size);
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
>> drivers/dma/at_xdmac.c:845:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
>> drivers/dma/at_xdmac.c:852:4: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
^
drivers/dma/at_xdmac.c: In function 'at_xdmac_tx_status':
>> drivers/dma/at_xdmac.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
dev_dbg(chan2dev(chan),
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As documented in printk-formats.txt the size_t should be printed with
%zu/%zd specfiers. This way it works on all archs.
make.cross ARCH=avr32
All warnings:
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_cyclic':
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
>> drivers/dma/at_xdmac.c:663: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
drivers/dma/at_xdmac.c: In function 'at_xdmac_prep_dma_memcpy':
>> drivers/dma/at_xdmac.c:765: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
>> drivers/dma/at_xdmac.c:794: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
>> drivers/dma/at_xdmac.c:815: warning: format '%u' expects type 'unsigned int', but argument 5 has type 'size_t'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver uses read_relaxed and writel_relaxed to read, write to IO
memory. the config defines COMPILE_TEST so gets compiled on different archs.
This causes issue as few archs like x86 etc don't define it.
So use readl/writel which is defined in all archs
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/dma/k3dma.c:790:12: warning: 'k3_dma_suspend' defined but not used [-Wunused-function]
drivers/dma/k3dma.c:806:12: warning: 'k3_dma_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/dma/sirf-dma.c:838:12: warning: 'sirfsoc_dma_pm_suspend' defined but not used [-Wunused-function]
drivers/dma/sirf-dma.c:879:12: warning: 'sirfsoc_dma_pm_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch simply adds a new DMATYPE for SAI which's included
in i.MX6 Solo X.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes a race condition about a list of shdma-base driver.
If we don't apply this patch, a dma slave driver (especially a usb
peripheral driver) may not be able to start the transfer.
If a dma slave driver has a callback, __ld_cleanup() will call
the callback before this driver removes the list. After the callback,
since the return value of __ld_cleanup() is not zero,
shdma_chan_ld_cleanup() calls __ld_cleanup() again. And, __ld_clean()
will removes the list.
At this time, if a dma slave driver calls dmaengine_submit() before
this driver removes the list, this driver will set schan->pm_state
to SHDMA_PM_PENDING in shdma_tx_submit(). And then, even if a dma
slave driver calls dma_async_issue_pending(), this driver don't
start the transfer because the schan->pm_state is SHDMA_PM_PENDING
in shdma_issue_pending().
So, this patch adds a new condition in __ld_clean() to check if the
schan->pm_state is SHDMA_PM_PENDING or not.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We currently have register offset information only for BAM IPs with revision
1.4.0. We add register offset table entries for the legacy (v1.3.0) version
of BAM IPs found on SoCs like APQ8064 and MSM8960.
The register offset table pointers are stored in DT data corresponding to the
BAM IP version specified in the compatible string.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The BAM DMA IP comes in different versions. The register offset layout varies
among these versions. The layouts depend on which generation/family of SoCs they
belong to.
The current SoCs(like 8084, 8074) have a layout where the Top level registers
come in the beginning of the address range, followed by pipe and event
registers. The BAM revision numbers fall above 1.4.0.
The older SoCs (like 8064, 8960) have a layout where the pipe registers come
first, and the top level come later. These have BAM revision numbers lesser than
1.4.0.
It isn't suitable to have macros provide the register offsets with the layouts
changed. Future BAM revisions may have different register layouts too. The
register addresses are now calculated by referring a table which contains a base
offset and multipliers for pipe/evnt/ee registers.
We have a common function bam_addr() which computes addresses for all the
registers. When computing address of top level/ee registers, we pass 0 to the
pipe argument in addr() since they don't have any multiple instances.
Some of the unused register definitions are removed. We can add new registers as
we need them.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The A23 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
A slight difference in sun8i is an undocumented register needs
to be toggled for dma to function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When platform_driver_probe() is not used, sdma_probe() can be called
by bind/unbind via sysfs. In addition, sdma_init() can be called by
sdma_probe(). Thus, __init annotation should be removed from sdma_init(),
Also, this patch fixes section mismatch warning.
WARNING: drivers/dma/built-in.o(.text+0xd6e4): Section mismatch in reference from the function sdma_probe() to the function
.init.text:sdma_init()
The function sdma_probe() references
the function __init sdma_init().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_init is wrong.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit f6f2421c0a removed pl330_info structure by embedding it into
pl330_dmac structure, but did not ensure that the dmac->ddma.dev
pointer gets initialised before use. When dma_alloc_coherent() gets
called on arm64 a WARN() gets triggered due to dev being NULL.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at arch/arm64/mm/dma-mapping.c:49 __dma_alloc_coherent+0xd0/0xe0()
Use an actual device structure for DMA allocation
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.17.0+ #5
Call trace:
[<ffffffc000087f24>] dump_backtrace+0x0/0x130
[<ffffffc000088064>] show_stack+0x10/0x1c
[<ffffffc0004e8af8>] dump_stack+0x74/0xb8
[<ffffffc0000aa444>] warn_slowpath_common+0x8c/0xb4
[<ffffffc0000aa4b8>] warn_slowpath_fmt+0x4c/0x58
[<ffffffc000092580>] __dma_alloc_coherent+0xcc/0xe0
[<ffffffc000092734>] __dma_alloc_noncoherent+0x64/0x158
[<ffffffc000312cd8>] pl330_probe+0x650/0x8f0
[<ffffffc00030e1d4>] amba_probe+0xa0/0xc8
[<ffffffc000350240>] really_probe+0xc4/0x22c
[<ffffffc0003504b4>] __driver_attach+0xa0/0xa8
[<ffffffc00034e5fc>] bus_for_each_dev+0x54/0x98
[<ffffffc00034fd8c>] driver_attach+0x1c/0x28
[<ffffffc00034fa08>] bus_add_driver+0x14c/0x204
[<ffffffc000350b84>] driver_register+0x64/0x130
[<ffffffc00030dcf8>] amba_driver_register+0x50/0x5c
[<ffffffc0006a60d0>] pl330_driver_init+0x10/0x1c
[<ffffffc0000814ac>] do_one_initcall+0x88/0x19c
[<ffffffc00068dab8>] kernel_init_freeable+0x140/0x1e0
[<ffffffc0004e5e18>] kernel_init+0x10/0xd4
---[ end trace 76f2d47a444e523e ]---
(NULL device *): dmac_alloc_resources:1821 Can't allocate memory!
(NULL device *): Unable to create channels for DMAC
This patch will also ensure that any dev_err messages are printed
with the appropriate device name.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The datasheet for PL330 says that the data buffer value in the CRD
register is 10bits wide. However, the value stored is "minus one",
which the driver corrects for. Maximum value that the data buffer
depth can have is 1024 lines, which requires 11 bits for storage.
While making updates I found printing the peripheral ID as a hex
value to be more useful as the datasheet shows the values that way.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MFIFO is shared by all channels so restrict each memcpy to it's fair
share. This is being over cautious, but without a global view of DMA
channel usage on a system it's not possible to come up with a more
optimum safe limit.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The algorithm used for programming the DMA Controller doesn't take into
consideration the requirements of transfers that are not aligned to the
bus width. This failure may result in DMA transferring one too few MFIFO
entries (so too few bytes are copied) or the DMA trying to write one too
many MFIFO entries and hanging because this is never provided.
See "MFIFO Usage Overview" chapter in the the TRM for "CoreLink DMA
Controller DMA-330", Revision r1p1.
We work around these shortcomings by making sure we pick a burst size
and length which ensures no bursts straddle an MFIFO entry.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
[squashed linker error "undefined reference to `__aeabi_uldivmod]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The prep_memcpy call was not setting any meaningful burst and width because it
was relying on the dma_slave_config was not set already.
Rework the needed conversion functions, and hardcode the width and burst to
use.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On runtime PM aware platforms the DMA have to manage its own power state. This
patch enables runtime PM support and applies necessary calls wherever it's
needed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch modifies the icg field to match the description
as mentioned in the DMA Linux framework.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a sanity check to see if frame_size is 1.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The segment list in a descriptor should be checked for empty, else
it will try to access invalid address for the first call. This
patch fixes this issue.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
[for nvidia]
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chanctnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
New atmel DMA controller known as XDMAC, introduced with SAMA5D4
devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The horrible split between the low-level part of the edma support
and the dmaengine front-end driver causes problems on multiplatform
kernels. This is an attempt to improve the situation slightly
by only registering the dmaengine devices that are actually
present.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: add missing include of linux/dma-mapping.h]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Dave Jiang
Ludovic Desroches
Jie Yang
Qiao Zhou
Colin Ian King
Geert Uytterhoeven
Dilek Uzulmez
Pramod Gurav
Arnd Bergmann
Linus Torvalds
Robert Baldyga
Laurent Pinchart
Lad, Prabhakar
Sergei Shtylyov
Addy Ke
Jiang Liu
Cyrille Pitchen
Nicholas Mc Guire
Andy Shevchenko
Andrew Bresticker
Dan Carpenter
Vinod Koul
Wolfram Sang
Kuninori Morimoto
Maxime Ripard
Paul Walmsley
Kevin Hao
Fabio Estevam
Wolfram Sang
Krzysztof Kozlowski
Jürg Billeter
Rickard Strandqvist
Asaf Vertz
Markus Elfring
Prarit Bhargava
Sebastian Andrzej Siewior
Jingchang Lu
Stefan Agner
Rafael J. Wysocki
Michele Curti
Julia Lawall
Sascha Hauer
Jassi Brar
Ralf Baechle
kbuild test robot
Jingoo Han
Nicolin Chen
Yoshihiro Shimoda
Archit Taneja
Chen-Yu Tsai
Andrew Jackson
Liviu Dudau
Jon Medhurst
Srikanth Thokala
Kiran Padwal