7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero the statistics counters when setting up the global
registers. Otherwise the counters will remain from the last boot if
the power has not been removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the scratch registers to be shown in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device map is used to route packets between cascaded switches.
Add dumping a switches device map via debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the statistics counters to be shown in debugfs.
This is particularly useful for the cpu and dsa ports, which cannot be
seen using ethtools -S.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code to retrieve a statistics counter into a function of its
own, so it can later be reused.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump the Address Translation Unit via a file in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the registers to be shown in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the newly introduced BRCM_PSEUDO_PHY_ADDR constant from
brcmphy.h instead of open-coding the Broadcom Ethernet switches
pseudo-PHY address (30).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -S on a DSA interface can deadlock for some switches because
the same lock is taken twice. Use the register read function which
expects the lock to be already held.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 31888234b7 ("net: dsa: mv88e6xxx: Replace stats mutex with SMI mutex")
Signed-off-by: David S. Miller <davem@davemloft.net>
MoCA interfaces require the use of an user-space daemon (mocad) which
will typically use cmd->autoneg to force the link. This is causing other
network manager applications not to get proper carrier down
notifications because of the following sequence of events:
- link down interrupt is received, link is set to 0 by the interrupt
handler
- fixed_link update callback runs and updates the BMSR register
accordingly
- PHY library polls the PHY for link status, sees the link is down,
proceeds with reporting that
- mocad gets notified of the link state and call phy_ethtool_sset()
with cmd->autoneg set to the link status (0)
- phy_start_aneg() is called at the end of phy_ethtool_sset() and sets
the PHY state to PHY_FORCING
Just make sure we notify the interface carrier appropriately when we
detect that the link is down in our fixed_link update callback. This is
made local to the bcm_sf2 driver as the PHY library does the right thing
in any case. This is similar to the GENET change introduced in
54d7c01d3e ("net: bcmgenet: enable MoCA
link state change detection").
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA can have nested MDIO busses, where the Ethernet MDIO bus is used
to access an MDIO bus within the switch which has the PHYs connected
to it. This nesting causes lockdep to give false positives. Use
mutex_lock_nested() to avoid this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the stats mutex by the SMI mutex to make
the locking concept simpler.
The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the PHY mutex by the SMI mutex to make
the locking concept simpler.
The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6185 is part of the family that the mv88e6131 driver
supports. Add it to the probe function, and set the number of ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6171 is one member of the family 6171/6175/6350/6351. Add the
other family members to the driver.
Not tested on these new devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 is part of the mv88e6352 family of devices. Move support
for it out of the mv88e6171 driver into the mv88e6352, which results
in some simplifications to the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use defines for registers, shifts and bits in the remaining register
accesses in the individual drivers, in order to aid readability.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that setting up a port is identical for all switches, centralisers
the code looping over all the ports to set them up.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port setup code in the individual drivers is identical for 6123,
6171, and 6352, and very similar in 6131. Move it all into mv88e6xxx,
using the chip families to differentiate on features.
Similarly, the global setup is also very similar. Move the majority
into mv8e6xxx.
The chips themselves fall into families. Add helpers which uses the
device IDs to determine if a device is a member of a family or not.
Add some additional device IDs to the existing list, to make these
helper functions more complete. However these IDs are not yet added to
the probe functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unregister for the mv88e6352_switch_driver.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).
Fixes: cca8b13375 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/mv88e6xxx.c: In function ‘mv88e6xxx_set_port_state’:
drivers/net/dsa/mv88e6xxx.c:905: warning: ‘ret’ may be used uninitialized in this function
If oldstate == state, mv88e6xxx_set_port_state() will return an
uninitialized value. Pre-initialize ret to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A duplicate declaration of 'ret' can result in hiding an error code.
Drop it.
Fixes: 17ee3e04dd ("net: dsa: Provide additional RMON statistics")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistic counters for the mv88e6172 never worked. This device is
a member of the 6352 family of chips, which has a slightly different
layout of the register used for capturing statistics. Add support for
detecting this family and poking the port in the right place in the
register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than refer to registers by number, define mnemonics. Also
define mnemonics for the commonly used bits within the registers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading the statistics from the hardware is the same for all
chips. What differs is the number of available statistics. Have just
one copy of the code in the shared mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mutex should be held while reading and writing to the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the common code for reading and writing phy registers into the
shared mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions could in future be used by other drivers. Move them
into the shared area.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell switches are all reset in nearly the same way. The only
difference is if the PPU should be enabled or not. Move this
code into the shared mv88x6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a step towards consolidating code, consistently set the
number of ports in the private state structure, and make use of it in
loops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will let us use the switch product IDs in the common source code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common initialization functions will be needed to enable
HW bridging support.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up the common code for setting up hardware bridging
and access to the forwarding database.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 has support for EEE. Check for the product ID and call
the common code if applicable.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable by using defines for the switch IDs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the switch id and save it away in the private mv88x6xxx structure
in a centralised piece of code, rather than each driver doing it itself.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for manipulating switch fdb entries by pointing to the
ndo_fdb functions implemented for mv88e6xxxx.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No vlan support at this time.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge support is similar for all chips supported by the mv88e6xxx code,
so add the code there.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will simplify adding offloaded bridge support later on.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli
Vivien Didelot
Andrew Lunn
David S. Miller
Geert Uytterhoeven
Guenter Roeck