There are multiple reasons for disabling this:
1. It provides no functional benefit. We pretty much only get a few more
sysfs entries for each port, but all that information is already
available from /sys/kernel/debug/target/qla-session-X
2. It already only works in private-loop mode. By disabling we'll be
getting more uniform behavior with fabric mode.
3. It creates complications for the new PLOGI handling mechanism:
scsi_transport_fc port deletion timer could race with new session
from initiator and cause logout after successful login.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
RSCN processing in qla2xxx driver can run in parallel with ELS/IO
processing. As such the decision to remove disappeared fc port's
session could be stale, because a new login sequence has occurred
since and created a brand new session.
Previous mechanism of dealing with this by delaying deletion request
was prone to erroneous deletions if the event that was supposed to
cancel the deletion never arrived or has been delayed in processing.
New mechanism relies on a time-like generation counter to serialize
RSCN updates relative to ELS/IO updates.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
cancel any commands from initiator's s_id that are still waiting
on qla_tgt_wq when PLOGI arrives.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- keep qla_tgt_sess object on the session list until it's freed
- modify use of sess->deleted flag to differentiate delayed
session deletion that can be cancelled from irreversible one:
QLA_SESS_DELETION_PENDING vs QLA_SESS_DELETION_IN_PROGRESS
- during IN_PROGRESS deletion all newly arrived commands and TMRs will
be rejected, existing commands and TMRs will be terminated when
given by the core to the fabric or simply dropped if session logout
has already happened (logout terminates all existing exchanges)
- new PLOGI will initiate deletion of the following sessions
(unless deletion is already IN_PROGRESS):
- with the same port_name (with logout)
- different port_name, different loop_id but the same port_id
(with logout)
- different port_name, different port_id, but the same loop_id
(without logout)
- additionally each new PLOGI will store imm notify iocb in the
same port_name session being deleted. When deletion process
completes this iocb will be acked. Only the most recent PLOGI
iocb is stored. The older ones will be terminated when replaced.
- new PRLI will initiate deletion of the following sessions
(unless deletion is already IN_PROGRESS):
- different port_name, different port_id, but the same loop_id
(without logout)
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since cmds go into qla_tgt_wq and TMRs don't, it's possible that TMR
like TASK_ABORT can be queued over the cmd for which it was meant.
To avoid this race, use a per-port list to keep track of cmds that
are enqueued to qla_tgt_wq but not yet processed. When a TMR arrives,
iterate through this list and remove any cmds that match the TMR.
This patch supports TASK_ABORT and LUN_RESET.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Swapnil Nagle <swapnil.nagle@purestorage.com>
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To fix some issues talking to ESX, this patch modifies the qla2xxx driver
so that it never logs into remote ports. This has the side effect of
getting rid of the "rports" entirely, which means we never log out of
initiators and never tear down sessions when an initiator goes away.
This is mostly OK, except that we can run into trouble if we have
initiator A assigned FC address X:Y:Z by the fabric talking to us, and
then initiator A goes away. Some time (could be a long time) later,
initiator B comes along and also gets FC address X:Y:Z (which is
available again, because initiator A is gone). If initiator B starts
talking to us, then we'll still have the session for initiator A, and
since we look up incoming IO based on the FC address X:Y:Z, initiator B
will end up using ACLs for initiator A.
Fix this by:
1. Handling RSCN events somewhat differently; instead of completely
skipping the processing of fcports, we look through the list, and if
an fcport disappears, we tell the target code the tear down the
session and tell the HBA FW to release the N_Port handle.
2. Handling "port down" events by flushing all of our sessions. The
firmware was already releasing the N_Port handle but we want the
target code to drop all the sessions too.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove unnecessary msleep from qlt_send_term_exchange as it
adds latency of 250 msec while sending terminate exchange to
an aborted task.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Adjust debug flag to match debug comment.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Request IOCB queue element(s) is reserved during
good path IO. Under error condition such as unable
to allocate IOCB handle condition, the IOCB count
that was reserved is not released.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
After updating the consumer index of ATIO Q, a read is
required to flush the write to the adapter register.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ Upstream commit ef86cb2059 ]
This patch fixes a kernel panic for qla2xxx Target core
Module driver introduced by a fix in the qla2xxx initiator code.
Commit ef86cb2 ("qla2xxx: Mark port lost when we receive an RSCN for it.")
introduced the regression for qla2xxx Target driver.
Stack trace will have following signature
--- <NMI exception stack> ---
[ffff88081faa3cc8] _raw_spin_lock_irqsave at ffffffff815b1f03
[ffff88081faa3cd0] qlt_fc_port_deleted at ffffffffa096ccd0 [qla2xxx]
[ffff88081faa3d20] qla2x00_schedule_rport_del at ffffffffa0913831[qla2xxx]
[ffff88081faa3d50] qla2x00_mark_device_lost at ffffffffa09159c5[qla2xxx]
[ffff88081faa3db0] qla2x00_async_event at ffffffffa0938d59 [qla2xxx]
[ffff88081faa3e30] qla24xx_msix_default at ffffffffa093a326 [qla2xxx]
[ffff88081faa3e90] handle_irq_event_percpu at ffffffff810a7b8d
[ffff88081faa3ee0] handle_irq_event at ffffffff810a7d32
[ffff88081faa3f10] handle_edge_irq at ffffffff810ab6b9
[ffff88081faa3f30] handle_irq at ffffffff8100619c
[ffff88081faa3f70] do_IRQ at ffffffff815b4b1c
--- <IRQ stack> ---
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When we open a device file descriptor, we currently have the
following:
vfio_group_get_device_fd()
mutex_lock(&group->device_lock);
open()
...
if (ret)
release()
If we hit that error case, we call the backend driver release path,
which for vfio-pci looks like this:
vfio_pci_release()
vfio_pci_disable()
vfio_pci_try_bus_reset()
vfio_pci_get_devs()
vfio_device_get_from_dev()
vfio_group_get_device()
mutex_lock(&group->device_lock);
Whoops, we've stumbled back onto group.device_lock and created a
deadlock. There's a low likelihood of ever seeing this play out, but
obviously it needs to be fixed. To do that we can use a reference to
the vfio_device for vfio_group_get_device_fd() rather than holding the
lock. There was a loop in this function, theoretically allowing
multiple devices with the same name, but in practice we don't expect
such a thing to happen and the code is already aborting from the loop
with break on any sort of error rather than continuing and only
parsing the first match anyway, so the loop was effectively unused
already.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Fixes: 20f300175a ("vfio/pci: Fix racy vfio_device_get_from_dev() call")
Reported-by: Joerg Roedel <joro@8bytes.org>
Tested-by: Joerg Roedel <jroedel@suse.de>
As well as some driver specific fixes there's several fixes here for the
core support for regulators supplying other regulators fixing both an
issue with ACPI support (which had never been tested before) and some
error handling and device removal issues that Javier noticed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVsm+oAAoJECTWi3JdVIfQsZoH/11WTUvq1YY6nv/3CM14owjH
LXUQmPR2lSj0PTQJUpbQm4Rk9007NPoArehlv+5UFBwmrW1uxt1F7/YrLqc7hcUO
ZPnL6IBUjuilU2yWBfJ+eK9QZyhBBfG+KbkSQy+ot6K+hdMH8RvYNF9ls7O5gCVP
iFADtO/hCahFAk9Y/iShGM4aY+cvNILPS88Ahqg3luTSc+JMQ6khhUYJiIV86xUQ
5T6Wu0JUZtKd4+SAPU0OtPnFOksTGB5RBKfnGi9/cDdv04JN6tETT54e8aEyQFfQ
uSHTsvZIvZgA0TmCqgmRWwSIujt2wZAm/SBNs0SLawyWLQsrnEvHlpBXwRZD3Us=
=uoMw
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"As well as some driver specific fixes there's several fixes here for
the core support for regulators supplying other regulators fixing both
an issue with ACPI support (which had never been tested before) and
some error handling and device removal issues that Javier noticed"
* tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Fix memory leak in regulator_resolve_supply()
regulator: core: Increase refcount for regulator supply's module
regulator: core: Handle full constraints systems when resolving supplies
regulator: 88pm800: fix LDO vsel_mask value
regulator: max8973: Fix up control flag option for bias control
regulator: s2mps11: Fix GPIO suspend enable shift wrapping bug
A small collection of pretty much unremarkable driver specific fixes
here plus the addition of a new device ID to spidev which requires no
other code changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVsm2PAAoJECTWi3JdVIfQlf0H/RmLs7XxNF6iIFsZDj32Pwn0
Oau1DhwYyMRwH+j6llALHNKi5s5aXjwzjWLTTS8NPa/anT86GscybXiMtMaZoutD
JITGP2fL0QS1GHxwKu0PIYeTiGK09tZ3x+U8Hc9P4rsdaxl9GIQq6MEKv7rO4eHe
vrmLdLrtywprKsP2A4DLSOaYjIbPuvrHOYutELUO+4Y6a+t3vSFrZtAgzN6N2YZC
BR2MljgffFPUIXCXI3rEtH1unzLVoTRqSDOgE4BZ8Yf4mxLNMn1/huaDugDEHhPi
FQPDjv0bARDzQwgHt4i8axdRi1mVrQKxXe4ZS6syw/YC/XNDQbWcc8JRBn1le98=
=C+po
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of pretty much unremarkable driver specific fixes
here plus the addition of a new device ID to spidev which requires no
other code changes"
* tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: Fix small DMA transfers
spi: zynq: missing break statement
spi: SPI_ZYNQMP_GQSPI should depend on HAS_DMA
spi: spidev: add compatible value for LTC2488
spi: img-spfi: fix support for speeds up to 1/4th input clock
Pull HID fixes from Jiri Kosina:
- kernel crash fixes for multitouch and wacom drivers, by Brent Adam
and Dan Carpenter
- cp2112 data packet race condition corruption fix, by Antonio Borneo
- a few new device IDs for wacom and microsoft drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: cp2112: fix to force single data-report reply
HID: wacom: Enable pad device for older Bamboo Touch tablets
HID: multitouch: Fix fields from pen report ID being interpreted for multitouch
HID: microsoft: Add quirk for MS Surface Type/Touch cover
HID: wacom: NULL dereferences on error in probe()
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
1280,800 0,800
+-------------+
| |
| |
| |
+-------------+
1280,0 0,0
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change of license from GPLv2 to dual-license (GPLv2 and BSD 2-Clause)
All contributors were contacted off-list and permission to make this
change was received. The complete list of contributors are Cc:ed here.
Cc: Tejun Heo <tj@kernel.org>
Cc: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: Sasha Levin <levinsasha928@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Moni Shoua <monis@mellanox.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the above is turned off then ipoib_cm_dev_init unconditionally
returns ENOSYS, and the newly added error handling in
0b3957 prevents ipoib from coming up at all:
kernel: mlx4_0: ipoib_transport_dev_init failed
kernel: mlx4_0: failed to initialize port 1 (ret = -12)
Fixes: 0b39578bcd (IB/ipoib: Use dedicated workqueues per interface)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
T3 HW only supports 32 bit MRs. If the system uses 64 bit memory
addresses, then a registered 32 bit MR will wrap and write to the
wrong memory when used with addresses > 4GB. To prevent this,
simply fail to allocate an MR on 64 bit machines (other means
of registering memory are still available and software can still
work, we just don't allow this means of memory registration).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().
static int sdhci_pxav3_probe(struct platform_device *pdev) {
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
...
if (match) {
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_of_parse;
sdhci_get_of_property(pdev);
pdata = pxav3_get_mmc_pdata(dev);
}
...
}
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Fixes: b650352dd3df("mmc: sdhci-pxa: Add device tree support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.
Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.
wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
Fixes: 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a0099 ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.
Fixes: d1e49f77d7 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().
Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.
Fix this by checking for 'host->data' before it is actually cleared.
Fixes: ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ")
CC: stable@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a follow up to ce31c1b0dc - there are
still a few LIO match_int() calls that don't check the return value.
Propagate errors rather than using the potentially uninitialised result.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here are some more instances where we are returning 0 from a configfs
store function, the unintended result of which is likely infinite retries
from userspace.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See https://bugzilla.redhat.com/show_bug.cgi?id=1240687
Returning 0 from a configfs store function results in infinite retries.
Reported-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
API compliance scanning with coccinelle flagged:
./drivers/scsi/qla2xxx/tcm_qla2xxx.c:407:2-29:
WARNING: timeout is HZ dependent
This was introduced in 'commit 75f8c1f693 ("[SCSI] tcm_qla2xxx: Add >=
24xx series fabric module for target-core")'. wait_for_completion_timeout()
expects a timeout in jiffies so the numeric constant makes the effective
timeout HZ dependent. Resolved by converting it to CONST * HZ.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This flag is currently never cleared, which can in rare cases
trigger a warn-on if it is still set but the block isn't
InSync.
So clear it when it isn't need, which includes if the replacement
device has failed.
Signed-off-by: NeilBrown <neilb@suse.com>
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reported-By: David Teigland <teigland@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
bitmap_read_sb is modifying mddev->bitmap_info.offset. This works for
the first bitmap read. However, when multiple bitmaps need to be opened
by the same node, it ends up corrupting the offset. Fix it by using a
local variable.
Also, bitmap_read_sb is not required in bitmap_copy_from_slot since
it is called in bitmap_create. Remove bitmap_read_sb().
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
request_module() can return 256 (process exited) in some cases,
which is not as specified in the documentation before the
request_module() definition. Convert the error to -ENOENT.
The positive error number results in bitmap_create() returning
a value that is meant to be an error but doesn't look like one,
so it is dereferenced as a point and causes a crash.
(not needed for stable as this is "experimental" code)
Fixes: edb39c9ded ("Introduce md_cluster_operations to handle cluster functions")
Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
If the bitmap read fails, the error code set is -EINVAL. However,
we don't check for errors and go ahead with cluster_setup.
Skip the cluster setup in case of error.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054c9 ("md/raid1: clean up read_balance.")
Cc: stable@vger.kernel.org (v3.0+)
Signed-off-by: NeilBrown <neilb@suse.com>
Regression fix for systemd getting confused about unknown connector state
after resume. Just stop setting the state to unknown, turned out to be a
silly idea anyway. What drivers imo really should do (and i915 still does
that) is forcing a full reprobe on resume to make sure connector changes
while suspended are caught. Most drivers seem to get this wrong. Otoh it
took us years to get fixes merged where some probe races resulted in
eating uevents, I guess userspace expectations for reliable hpd are just
really low :(
* tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm: Stop resetting connector state to unknown
arb_timer kernel side fix from Chris.
* tag 'drm-intel-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Use two 32bit reads for select 64bit REG_READ ioctls
Some amdgpu fixes.
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
Return proper pgprot for ARM64. This is required for objects like
Nouveau fences to be mapped with expected coherency.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
CPU 0 | CPU 1
|
uart_close() |
tty_port_close_start() |
tty->closing = 1 |
tty_ldisc_flush() |
| => IRQ
| while (LSR & data ready)
| uart_insert_char()
| tty_flip_buffer_push()
| <= EOI
stop_rx() | .
uart_shutdown() | .
free xmit.buf | .
tty_port_tty_set(NULL) | .
tty->closing = 0 | .
| flush_to_ldisc()
| n_tty_receive_buf_common()
| __receive_buf()
| ...
| commit_echoes()
| uart_flush_chars()
| __uart_start()
| ** OOPS on port.tty deref **
tty_ldisc_flush() |
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes: 2e75891083 ("serial: core: Flush ldisc after dropping port
mutex in uart_close()")
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 068500e08d.
According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: David Jander <david@protonic.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls to regmap_raw_read/write needed register rewrite in a
similar way as function calls to regmap_read/write already had.
This enables reading/writing the serial datastream to the device.
Signed-off-by: Bo Svangård <bo.svangard@embeddedart.se>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I2C=m and SPI=y or-ing them will produce =y while
what we need is the lower bound, i.e. =m. Fortunately
SPI is a boolean so we need to handle only one special
case.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In probe, we use dev_id as array index of etraxfs_uart_ports and store the
index in port->line. So etraxfs_uart_ports[port->line] should be released
when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling signalling char, claim the termios write lock before
signalling waiting readers and writers to prevent further i/o
before flushing the echo and output buffers. This prevents a
userspace signal handler which may output from racing the terminal
flush.
Reference: Bugzilla #99351 ("Output truncated in ssh session after...")
Fixes: commit d2b6f44779 ("n_tty: Fix signal handling flushes")
Reported-by: Filipe Brandenburger <filbranden@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Cc: stable@vger.kernel.org
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* bmc150_magn - add missing regmap dependency and ensure on a wrong chip
case report hte chip id rather than a previous return value.
* mmc35240 - Fill a null pointer derefrence and wrong SET / RESET logic
that results in North and South being swapped.
* mlx96014 - correct the offset value reported to userspace (wrong sign)
* vf610 - Prevent non aligned register reading.
* mcp320x - Another null pointer deference bug.
* mma8452 - change threshold type from THRESH to MAG to reflect the fact
that the sign of the signal is not known when the event is signaled.
* stk3310 - move device registert to end of probe to avoid race conditions
when coming up, check for invalid client->irq values and make it work
for both endian types of host.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=AEVb
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
3rd round of IIO fixes for the 4.2 cycle.
* bmc150_magn - add missing regmap dependency and ensure on a wrong chip
case report hte chip id rather than a previous return value.
* mmc35240 - Fill a null pointer derefrence and wrong SET / RESET logic
that results in North and South being swapped.
* mlx96014 - correct the offset value reported to userspace (wrong sign)
* vf610 - Prevent non aligned register reading.
* mcp320x - Another null pointer deference bug.
* mma8452 - change threshold type from THRESH to MAG to reflect the fact
that the sign of the signal is not known when the event is signaled.
* stk3310 - move device registert to end of probe to avoid race conditions
when coming up, check for invalid client->irq values and make it work
for both endian types of host.
Bugfixes and documentation fixes. Igor's patch that allows
users to tweak memory table size is borderline,
but it does fix known crashes, so I merged it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVpBzpAAoJECgfDbjSjVRpQXEIAMEqetqPuRduynjIw2HNktle
fe/UUhvipwTsAM4R2pmcEl5tW04A/M54RkXN4iVy0rPshAfG3Fh4XTjLmzSGU0fI
KD6qX8/Zc/+DUWnfe3aUC6jOOrjb7c4xRKOlQ9X8lZgi2M6AzrPeoZHFTtbX34CU
2kcnv5Sb1SaI/t2SaCc2CaKilQalEOcd59gGjje2QXjidZnIVHwONrOyjBiINUy6
GzfTgvAje8ZiG6951W3HDwwSfcqXezin27LJqnZgaLCwTCKt2gdQ2MAKjrfP2aVF
+gX2B4XxcFLutMVx/obsjvA1ceipubyUauRLB3mnO3P5VOj1qbofa2lj4pzQ80k=
=EKPr
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes from Michael Tsirkin:
"Bugfixes and documentation fixes.
Igor's patch that allows users to tweak memory table size is
borderline, but it does fix known crashes, so I merged it"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: add max_mem_regions module parameter
vhost: extend memory regions allocation to vmalloc
9p/trans_virtio: reset virtio device on remove
virtio/s390: rename drivers/s390/kvm -> drivers/s390/virtio
MAINTAINERS: separate section for s390 virtio drivers
virtio: define virtio_pci_cfg_cap in header.
virtio: Fix typecast of pointer in vring_init()
virtio scsi: fix unused variable warning
vhost: use binary search instead of linear in find_region()
virtio_net: document VIRTIO_NET_CTRL_GUEST_OFFLOADS
The fixes include:
* A couple of fixes for the new ARM-SMMUv3 driver to fix issues found
on the first real implementation of that hardware.
* A patch for the Intel VT-d driver to fix a domain-id leak.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zWOU
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"The fixes include:
- a couple of fixes for the new ARM-SMMUv3 driver to fix issues found
on the first real implementation of that hardware.
- a patch for the Intel VT-d driver to fix a domain-id leak"
* tag 'iommu-fixes-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix VM domain ID leak
iommu/arm-smmu: Skip the execution of CMD_PREFETCH_CONFIG
iommu/arm-smmu: Enlarge STRTAB_L1_SZ_SHIFT to support larger sidsize
iommu/arm-smmu: Fix the values of ARM64_TCR_{I,O}RGN0_SHIFT
iommu/arm-smmu: Fix LOG2SIZE setting for 2-level stream tables
iommu/arm-smmu: Fix the index calculation of strtab
VCE, UVD DPM work similarly to SCLK DPM. Report the current
clock levels for UVD and VCE via debugfs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CZ uses a different set of registers compared to previous asics
and supports separate NB and GFX planes.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For boards with bad VCE blocks, only configure the working
block.
v2: use the harvest info for pipe setup
v3: fix mask check as noted by Leo
v4: add dGPU support
Reviewed-by: Christian König <christian.koenig@amd.com> (v2)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This doesn't seem strictly necessary with Tonga right now, but that might
change with future power management enhancements.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Something (ATOM BIOS?) seems to be clobbering the LB_INTERRUPT_MASK
register while the CRTC is off, which caused e.g. glxgears or
gnome-shell to hang after a modeset.
Reviewed-and-Tested-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Sonny Jiang <sonny.jiang@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
This continues the attempt to fix commit fb170fb4c5 ("iommu/vt-d:
Introduce helper functions to make code symmetric for readability").
The previous attempt in commit 7168440690 ("iommu/vt-d: Detach
domain *only* from attached iommus") overlooked the fact that
dmar_domain.iommu_bmp gets cleared for VM domains when devices are
detached:
intel_iommu_detach_device
domain_remove_one_dev_info
domain_detach_iommu
The domain is detached from the iommu, but the iommu is still attached
to the domain, for whatever reason. Thus when we get to domain_exit(),
we can't rely on iommu_bmp for VM domains to find the active iommus,
we must check them all. Without that, the corresponding bit in
intel_iommu.domain_ids doesn't get cleared and repeated VM domain
creation and destruction will run out of domain IDs. Meanwhile we
still can't call iommu_detach_domain() on arbitrary non-VM domains or
we risk clearing in-use domain IDs, as 7168440690 attempted to
address.
It's tempting to modify iommu_detach_domain() to test the domain
iommu_bmp, but the call ordering from domain_remove_one_dev_info()
prevents it being able to work as fb170fb4c5 seems to have intended.
Caching of unused VM domains on the iommu object seems to be the root
of the problem, but this code is far too fragile for that kind of
rework to be proposed for stable, so we simply revert this chunk to
its state prior to fb170fb4c5.
Fixes: fb170fb4c5 ("iommu/vt-d: Introduce helper functions to make
code symmetric for readability")
Fixes: 7168440690 ("iommu/vt-d: Detach domain *only* from attached
iommus")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
After commit 0fd972a7d9 ("module: relocate module_init from init.h to module.h")
ans-lcd module fails to build with:
drivers/macintosh/ans-lcd.c:201:1: warning: data definition has no type or storage class [enabled by default]
module_init(anslcd_init);
^
drivers/macintosh/ans-lcd.c:201:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
drivers/macintosh/ans-lcd.c:201:1: warning: parameter names (without types) in function declaration [enabled by default]
drivers/macintosh/ans-lcd.c:202:1: warning: data definition has no type or storage class [enabled by default]
module_exit(anslcd_exit);
^
drivers/macintosh/ans-lcd.c:202:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
drivers/macintosh/ans-lcd.c:202:1: warning: parameter names (without types) in function declaration [enabled by default]
drivers/macintosh/ans-lcd.c:155:1: warning: 'anslcd_init' defined but not used [-Wunused-function]
anslcd_init(void)
^
drivers/macintosh/ans-lcd.c:195:1: warning: 'anslcd_exit' defined but not used [-Wunused-function]
anslcd_exit(void)
^
This commit fixes it by replacing linux/init.h by linux/module.h.
Fixes: 0fd972a7d9 ("module: relocate module_init from init.h to module.h")
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
chrdev_open() increases reference counter on cdev->owner. Instead of
assigning the owner to mei subsystem, the owner has to be set to the
underlaying HW module (mei_me or mei_txe), so once the device is opened
the HW module cannot be unloaded.
Cc: <stable@vger.kernel.org> #3.17+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
v4.2-rc1 enabled huge page support for ioremap(..).
Calling vmalloc_to_page after v4.2-rc1 results in the
crash shown below on the host upon booting X100 coprocessors:
BUG: unable to handle kernel paging request at ffffc47c00000000
IP: [<ffffffff811a2c0c>] vmalloc_to_page+0x6c/0xb0
This patch fixes this crash by obtaining the fake struct page
pointer which is required to be passed into dma_map_sg(..)
by calling pfn_to_page(..) instead of vmalloc_to_page(..).
Link: https://lkml.org/lkml/2015/7/18/110
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Suggested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the reference count becomes 0 when put_device() is called, it will
execute the release callback where we are freeing all the allocated
memory associated with the device. So if we just continue on the error
path then we are again freeing devname and trying to dereference par_dev
which has already been free-ed in the release callback.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the reference count becomes 0 when put_device() is called, it will
execute the release callback where we are freeing all the allocated
memory associated with the device. We missed freeing par_dev->state.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After registering the device if exclusive access fails for any reason
then we need to unregister the device to remove all references.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug that the bitmap superblock isn't initialised properly for
dm-raid, so a new field can have garbage in new fields.
(dm-raid does initialisation in the kernel - md initialised the
superblock in mdadm).
This means that for dm-raid we cannot currently trust the new ->nodes
field. So:
- use __GFP_ZERO to initialise the superblock properly for all new
arrays
- initialise all fields in bitmap_info in bitmap_new_disk_sb
- ignore ->nodes for dm arrays (yes, this is a hack)
This bug exposes dm-raid to bug in the (still experimental) md-cluster
code, so it is suitable for -stable. It does cause crashes.
References: https://bugzilla.kernel.org/show_bug.cgi?id=100491
Cc: stable@vger.kernel.org (v4.1)
Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
An incorrect definition of CCR_PM_USBPW3 in ohci-tmio.c is a perennial
source of invalid diagnoses from static scanners, such as in
<http://marc.info/?l=linux-usb&m=143634574527641&w=2>. This patch
fixes the definition.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Binderman <dcb314@hotmail.com>
CC: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grain-media GM12U320 based devices are mini video projectors using USB for
both power and video data transport.
Their usb-storage interface is a virtual windows driver CD.
The gm12u320 kms driver needs these interfaces to talk to the device and
export it as framebuffer & kms dri device nodes, so make sure that the
usb-storage driver does not bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device automatically switches itself to another mode (0x1405)
unless the specific access pattern of Windows is followed in its
initial mode. That makes a dirty unmount of the internal storage
devices inevitable if they are mounted. So the card reader of
such a device should be ignored, lest an unclean removal become
inevitable.
This replaces an earlier patch that ignored all LUNs of this device.
That patch was overly broad.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Reviewed-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug introduced by commit 977dcfdc60 ("USB: OHCI:
don't lose track of EDs when a controller dies"). The commit changed
ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had
been called. The user-visible consequence is that the driver
occasionally crashes or locks up when an URB is submitted while
another URB for the same endpoint is being unlinked.
This patch moves the ED state change later, to the right place. The
drawback is that now we may unnecessarily execute some instructions
multiple times when a controller dies. Since controllers dying is an
exceptional occurrence, a little wasted time won't matter.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Heiko Przybyl <lil_tux@web.de>
Tested-by: Heiko Przybyl <lil_tux@web.de>
Fixes: 977dcfdc60
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 25cd2882e2 ("usb/xhci: Change how we indicate a host supports
Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed
root hub. The intention of that change was to avoid touching usb core
internal field, a.k.a. lpm_capable, and let usb core to set it by
checking U1 and U2 exit latency values in the descriptor.
Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately,
root hub is a special usb device as it has no parent. Hub_port_init()
will never be called for a root hub device. That means lpm_capable will
by no means be set for the root hub. As the result, lpm isn't functional
at all in Linux kernel.
This patch add the code to check and set lpm_capable when registering a
root hub device. It could be back-ported to kernels as old as v3.15,
that contains the Commit 25cd2882e2 ("usb/xhci: Change how we indicate
a host supports Link PM.").
Cc: stable@vger.kernel.org # 3.15
Reported-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
1) Don't use shared bluetooth antenna in iwlwifi driver for management
frames, from Emmanuel Grumbach.
2) Fix device ID check in ath9k driver, from Felix Fietkau.
3) Off by one in xen-netback BUG checks, from Dan Carpenter.
4) Fix IFLA_VF_PORT netlink attribute validation, from Daniel Borkmann.
5) Fix races in setting peeked bit flag in SKBs during datagram
receive. If it's shared we have to clone it otherwise the value can
easily be corrupted. Fix from Herbert Xu.
6) Revert fec clock handling change, causes regressions. From Fabio
Estevam.
7) Fix use after free in fq_codel and sfq packet schedulers, from WANG
Cong.
8) ipvlan bug fixes (memory leaks, missing rcu_dereference_bh, etc.)
from WANG Cong and Konstantin Khlebnikov.
9) Memory leak in act_bpf packet action, from Alexei Starovoitov.
10) ARM bpf JIT bug fixes from Nicolas Schichan.
11) Fix backwards compat of ANY_LAYOUT in virtio_net driver, from
Michael S Tsirkin.
12) Destruction of bond with different ARP header types not handled
correctly, fix from Nikolay Aleksandrov.
13) Revert GRO receive support in ipv6 SIT tunnel driver, causes
regressions because the GRO packets created cannot be processed
properly on the GSO side if we forward the frame. From Herbert Xu.
14) TCCR update race and other fixes to ravb driver from Sergei
Shtylyov.
15) Fix SKB leaks in caif_queue_rcv_skb(), from Eric Dumazet.
16) Fix panics on packet scheduler filter replace, from Daniel Borkmann.
17) Make sure AF_PACKET sees properly IP headers in defragmented frames
(via PACKET_FANOUT_FLAG_DEFRAG option), from Edward Hyunkoo Jee.
18) AF_NETLINK cannot hold mutex in RCU callback, fix from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
ravb: fix ring memory allocation
net: phy: dp83867: Fix warning check for setting the internal delay
openvswitch: allocate nr_node_ids flow_stats instead of num_possible_nodes
netlink: don't hold mutex in rcu callback when releasing mmapd ring
ARM: net: fix vlan access instructions in ARM JIT.
ARM: net: handle negative offsets in BPF JIT.
ARM: net: fix condition for load_order > 0 when translating load instructions.
tcp: suppress a division by zero warning
drivers: net: cpsw: remove tx event processing in rx napi poll
inet: frags: fix defragmented packet's IP header for af_packet
net: mvneta: fix refilling for Rx DMA buffers
stmmac: fix setting of driver data in stmmac_dvr_probe
sched: cls_flow: fix panic on filter replace
sched: cls_flower: fix panic on filter replace
sched: cls_bpf: fix panic on filter replace
net/mdio: fix mdio_bus_match for c45 PHY
net: ratelimit warnings about dst entry refcount underflow or overflow
caif: fix leaks and race in caif_queue_rcv_skb()
qmi_wwan: add the second QMI/network interface for Sierra Wireless MC7305/MC7355
ravb: fix race updating TCCR
...
*) Fix PIPE3 PM so that all its users (PCIe, SATA, USB) can
idle and resume
*) Fix a compiler error in pxa
*) Fix pll divider values in berlin-usb phy driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uBk6
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.2-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.2-rc
*) Fix PIPE3 PM so that all its users (PCIe, SATA, USB) can
idle and resume
*) Fix a compiler error in pxa
*) Fix pll divider values in berlin-usb phy driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Port link change with port in resume state should not be
reported to usbcore, as this is an internal state to be
handled by xhci driver. Reporting PLC to usbcore may
cause usbcore clearing PLC first and port change event irq
won't be generated.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the link is just waken, it's in Resume state, and driver sets PLS to
U0. This refers to Phase 1. Phase 2 refers to when the link has completed
the transition from Resume state to U0.
With the fix of xhci: report U3 when link is in resume state, it also
exposes an issue that usb3 roothub and controller can suspend right
after phase 1, and this causes a hard hang in controller.
To fix the issue, we need to prevent usb3 bus suspend if any port is
resuming in phase 1.
[merge separate USB2 and USB3 port resume checking to one -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_hub_report_usb3_link_state() returns pls as U0 when the link
is in resume state, and this causes usb core to think the link is in
U0 while actually it's in resume state. When usb core transfers
control request on the link, it fails with TRB error as the link
is not ready for transfer.
To fix the issue, report U3 when the link is in resume state, thus
usb core knows the link it's not ready for transfer.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resetting a device the number of active TTs may need to be
corrected by xhci_update_tt_active_eps, but the number of old active
endpoints supplied to it was always zero, so the number of TTs and the
bandwidth reserved for them was not updated, and could rise
unnecessarily.
This affected systems using Intel's Patherpoint chipset, which rely on
software bandwidth checking. For example, a Lenovo X230 would lose the
ability to use ports on the docking station after enough suspend/resume
cycles because the bandwidth calculated would rise with every cycle when
a suitable device is attached.
The correct number of active endpoints is calculated in the same way as
in xhci_reserve_bandwidth.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Campbell <bacam@z273.org.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
virt_dev->num_cached_rings counts on freed ring and is not updated
correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring
is added into cache and then num_rings_cache is incremented as below:
virt_dev->ring_cache[rings_cached] =
virt_dev->eps[ep_index].ring;
virt_dev->num_rings_cached++;
here, free ring pointer is added to a current index and then
index is incremented.
So current index always points to empty location in the ring cache.
For getting available free ring, current index should be decremented
first and then corresponding ring buffer value should be taken from ring
cache.
But In function xhci_endpoint_init(), the num_rings_cached index is
accessed before decrement.
virt_dev->eps[ep_index].new_ring =
virt_dev->ring_cache[virt_dev->num_rings_cached];
virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;
virt_dev->num_rings_cached--;
This is bug in manipulating the index of ring cache.
And it should be as below:
virt_dev->num_rings_cached--;
virt_dev->eps[ep_index].new_ring =
virt_dev->ring_cache[virt_dev->num_rings_cached];
virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;
Cc: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI in Intel CherryView / Braswell Platform requires
a driver workaround to get xHCI D3 working. Without this
workaround, xHCI might not enter D3.
Workaround is to configure SSIC PORT as "unused" before D3
entry and "used" after D3 exit. This is done through a
vendor specific register (PORT2_SSIC_CONFIG_REG2 at offset
0x883c), in xhci suspend / resume callbacks.
Verified xHCI D3 works fine in CherryView / Braswell platform.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel xhci hw that require XHCI_PME_STUCK quirk have as default disabled
xhci from going to D3 state in runtime suspend. Driver needs to verify
it can deal with the hw by calling an ACPI _DSM method to get D3 enabled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
end_cmd finishes request associated with nullb_cmd struct, so we
should save pointer to request_queue in a local variable before
calling end_cmd.
The problem was causes general protection fault with slab poisoning
enabled.
Fixes: 8b70f45e2e ("null_blk: restart request processing on completion handler")
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This fixes an issue introduced in commit b23c843992 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.
The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.
This problem became aparent after commit 76e838c9f7 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.
'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.
Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.
To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's causing piles of issues since we've stopped forcing full detect
cycles in the sysfs interfaces with
commit c484f02d0f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Mar 6 12:36:42 2015 +0000
drm: Lighten sysfs connector 'status'
The original justification for this was that the hpd handlers could
use the unknown state as a hint to force a full detection. But current
i915 code isn't doing that any more, and no one else really uses reset
on resume. So instead just keep the old state around.
References: http://article.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/62584
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100641
Cc: Rui Matos <tiagomatos@gmail.com>
Cc: Julien Wajsberg <felash@gmail.com>
Cc: kuddel.mail@gmx.de
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: stable@vger.kernel.org
Acked-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rui Tiago Cação Matos <tiagomatos@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The driver is written as if it can adapt to a low memory situation allocating
less RX skbs and TX aligned buffers than the respective RX/TX ring sizes. In
reality though the driver would malfunction in this case. Stop being overly
smart and just fail in such situation -- this is achieved by moving the memory
allocation from ravb_ring_format() to ravb_ring_init().
We leave dma_map_single() calls in place but make their failure non-fatal
by marking the corresponding RX descriptors with zero data size which should
prevent DMA to an invalid addresses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning: logical ‘or’ of collectively exhaustive tests is always true
Change the internal delay check from an 'or' condition to an 'and'
condition.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'event_work' worker used by dm-raid may still be running
when the array is stopped. This can result in an oops.
So flush the workqueue on which it is run after detaching
and before destroying the device.
Reported-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: stable@vger.kernel.org (2.6.38+ please delay 2 weeks after -final release)
Fixes: 9d09e663d5 ("dm: raid456 basic support")
'reshape_position' tracks where in the reshape we have reached.
'reshape_safe' tracks where in the reshape we have safely recorded
in the metadata.
These are compared to determine when to update the metadata.
So it is important that reshape_safe is initialised properly.
Currently it isn't. When starting a reshape from the beginning
it usually has the correct value by luck. But when reducing the
number of devices in a RAID10, it has the wrong value and this leads
to the metadata not being updated correctly.
This can lead to corruption if the reshape is not allowed to complete.
This patch is suitable for any -stable kernel which supports RAID10
reshape, which is 3.5 and later.
Fixes: 3ea7daa5d7 ("md/raid10: add reshape support")
Cc: stable@vger.kernel.org (v3.5+ please wait for -final to be out for 2 weeks)
Signed-off-by: NeilBrown <neilb@suse.com>
Cache size can grow or shrink due to various pressures at
any time. So when we resize the cache as part of a 'grow'
operation (i.e. change the size to allow more devices) we need
to blocks that automatic growing/shrinking.
So introduce a mutex. auto grow/shrink uses mutex_trylock()
and just doesn't bother if there is a blockage.
Resizing the whole cache holds the mutex to ensure that
the correct number of new stripes is allocated.
This bug can result in some stripes not being freed when an
array is stopped. This leads to the kmem_cache not being
freed and a subsequent array can try to use the same kmem_cache
and get confused.
Fixes: edbe83ab4c ("md/raid5: allow the stripe_cache to grow and shrink.")
Cc: stable@vger.kernel.org (4.1 - please delay until 2 weeks after release of 4.2)
Signed-off-by: NeilBrown <neilb@suse.com>
* fix device ID check for AR956x
iwlwifi:
* bug fixes specific for 8000 series
* fix a crash in time events
* fix a crash in PCIe transport
* fix BT Coex code that prevented association on certain
devices (3160).
* revert the new RBD allocation model because it introduced
a bug when running on weak VM setups.
* new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVrQ65AAoJEG4XJFUm622bArgH/jlGm44aPLVTtTfc3Qi/yH1m
pVZ+F6Z4FhFM8Ln/skL/PIWPbxmcwMQ9IYiDI+1y0obr5RaNGZbh5EBwLcNQzAII
L9aO7vGGQRHewJj3LAY4ovkT7xYT6Kra4iZuXrozeq8CJN2/0l4Yv2uPkwPtszIf
Gp1QGgCbvUzaPdIIevx4bMyLcC5h58y7Thg2+kxSSo/VFJxGh2DFFnLuJx5RVS1D
r7fBWH5BzUPP1sh84Gt+0IpjyoxqpWiI//Wqg2Hkt6zdis3fixDvK8Wm08EewZdj
Wf63HgOzQeL9vE6IHg3WuUiR8QOn51+oqDWCtbrRemBsywZ9rc4vesMAREjcw2Q=
=ygb2
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
ath9k:
* fix device ID check for AR956x
iwlwifi:
* bug fixes specific for 8000 series
* fix a crash in time events
* fix a crash in PCIe transport
* fix BT Coex code that prevented association on certain
devices (3160).
* revert the new RBD allocation model because it introduced
a bug when running on weak VM setups.
* new device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Some dead defines dropped from the Samsung driver, was
targeted for -rc2 but got delayed
- Drop the strict mode from abx500, this was too strict
- Fix the R-Car sparse IRQs code to work as intended
- Fix the IRQ code for the pinctrl-single GPIO backend to not
enforce threaded IRQs
- Clear the latched events/IRQs for the Broadcom BCM2835
driver
- Fix up debugfs for the Freescale imx1 driver
- Fix a typo bug in the Schmitt Trigger setup in the LPC18xx
driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pDEn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are some overly ripe pin control fixes for the v4.2 series.
They got delayed because of various crap commits and having to clean
and rinse the patch stack a few times. Now they are however looking
good.
- some dead defines dropped from the Samsung driver, was targeted for
-rc2 but got delayed
- drop the strict mode from abx500, this was too strict
- fix the R-Car sparse IRQs code to work as intended
- fix the IRQ code for the pinctrl-single GPIO backend to not enforce
threaded IRQs
- clear the latched events/IRQs for the Broadcom BCM2835 driver
- fix up debugfs for the Freescale imx1 driver
- fix a typo bug in the Schmitt Trigger setup in the LPC18xx driver"
* tag 'pinctrl-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: lpc18xx: fix schmitt trigger setup
Subject: pinctrl: imx1-core: Fix debug output in .pin_config_set callback
pinctrl: bcm2835: Clear the event latch register when disabling interrupts
pinctrl: single: ensure pcs irq will not be forced threaded
sh-pfc: fix sparse GPIOs for R-Car SoCs
pinctrl: abx500: remove strict mode
pinctrl: samsung: Remove old unused defines
With commit c03abd8463 ("net: ethernet: cpsw: don't requests IRQs
we don't use") common isr and napi are separated into separate tx isr
and rx isr/napi, but still in rx napi tx events are handled. So removing
the tx event handling in rx napi.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware sometimes mysteriously totally flummoxes the 64bit
read of a 64bit register when read using a single instruction, split the
read into two instructions. Since the read here is of automatically
incrementing timestamp counters, we also have to be very careful in
order to make sure that it does not increment between the two
instructions.
However, since userspace tried to workaround this issue and so enshrined
this ABI for a broken hardware read and in the process neglected that
the read only fails in some environments, we have to introduce a new
uABI flag for userspace to request the 2x32 bit accurate read of the
timestamp.
v2: Fix alignment check and include details of the workaround for
userspace.
Reported-by: Karol Herbst <freedesktop@karolherbst.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91317
Testcase: igt/gem_reg_read
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Tested-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
caused old UEFI spec (< 2.3) versions of the memory error record
structure to be declared invalid - Tony Luck
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kSV0
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull an EFI fix from Matt Fleming:
- Fix a bug in the Common Platform Error Record (CPER) driver that
caused old UEFI spec (< 2.3) versions of the memory error record
structure to be declared invalid. (Tony Luck)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On built-in kernels this warning will always splat, even if no ivtvfb
hardware is present, as this is part of the module init:
if (WARN(pat_enabled(),
"ivtvfb needs PAT disabled, boot with nopat kernel parameter\n")) {
Fix that by shifting the PAT requirement check out under the code
that does the "quasi-probe" for the device.
This device driver relies on an existing driver to find its own devices,
it looks for that device driver and its own found devices, then uses
driver_for_each_device() to try to see if it can probe each of those
devices as a frambuffer device with ivtvfb_init_card().
We tuck the PAT requiremenet check then on the ivtvfb_init_card() call
making the check at least require an ivtv device present before
complaining.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: andy@silverblocksystems.net
Cc: benh@kernel.crashing.org
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: dledford@redhat.com
Cc: jkosina@suse.cz
Cc: julia.lawall@lip6.fr
Cc: luto@amacapital.net
Cc: mchehab@osg.samsung.com
Link: http://lkml.kernel.org/r/1437167245-28273-3-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With the actual code, if a memory allocation error happens while
refilling a Rx descriptor, then the original Rx buffer is both passed
to the networking stack (in a SKB) and let in the Rx ring. This leads
to various kernel oops and crashes.
As a fix, this patch moves Rx descriptor refilling ahead of building
SKB with the associated Rx buffer. In case of a memory allocation
failure, data is dropped and the original DMA buffer is put back into
the Rx ring.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Tested-by: Yoann Sculo <yoann@sculo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 803f8fc462 ("stmmac: move driver data setting into
stmmac_dvr_probe") mistakenly set priv and not priv->dev as
driver data. This meant that the remove, resume and suspend
callbacks that fetched and tried to use this data would most
likely explode. Fix the issue by using the correct variable.
Fixes: 803f8fc462 ("stmmac: move driver data setting into stmmac_dvr_probe")
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We store c45 PHY's id information in c45_ids, so it should be used to
check the matching between PHY driver and PHY device for c45 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.
Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCCR.TSRQn bit may get clearead after TCCR gets read, so that TCCR write
would get skipped. We don't need to check this bit before setting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:
1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
bond0 has the same mac address with eth0, it is MAC1.
2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
eth1 is backup, eth1 has MAC2.
3) ifconfig eth0 down
eth1 became active slave, bond will swap MAC for eth0 and eth1,
so eth1 has MAC1, and eth0 has MAC2.
4) ifconfig eth1 down
there is no active slave, and eth1 still has MAC1, eth2 has MAC2.
5) ifconfig eth0 up
the eth0 became active slave again, the bond set eth0 to MAC1.
Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.
This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVp19MAAoJEP5prqPJtc/HsA8IAIqYKwJtXHItVoG6GBxLo/iJ
G6OhCxSgDPUdytdyvWRmYL+2g6q9+BefnApwGroM0wowytHx4I6kF2O4LKEvthnD
TzDV6uY0n1CR8FzCdfQdTFedAfxIx7DLCqY/iC+JRFTh6Vhvj46WtHickthu4Se+
ygTWg5f5Da086JTUtwbb75TCHJv8xxtN57t6yZTtDoyaftqWd1Dzrmi8dBwHRWBA
6X/rE4VekFwFCbqOlv5ghm86lD77sMTEaU0xkm9FeZmO/CnUD3JASwi844RtCqXR
wj3OJ89qH14YmpJwjpakIwHfTyyPJurzPpPkCTZ6awmdNhCvp+h3nbfjKRqs0WU=
=pQGs
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.2-20150716' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-16
this is a pull request of 2 patches by Stefan Agner. He fixes the resume
operation in the mcp251x driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)
After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16c6 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: David S. Miller <davem@davemloft.net>
drm_vblank_on() now warns on nested use or if vblank is not properly
initialized. This patch fixes Atmel HLCDC vblank initial state.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
[ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O
4.2.0-rc2+ #8
[ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[ 908.984181] Call Trace:
[ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[ 908.984225] [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[ 908.984228] [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[ 908.984244] [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[ 908.984247] ---[ end trace 7c006ed4abbef24b ]---
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f939981492 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd ("bonding: Manage /proc/net/bonding/ entries from
the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_map_single and dma_unmap_single should set "gadget->dev.parent"
instead of "&gadget->dev" in the first argument because the parent has
a udc controller's device pointer.
Otherwise, iommu functions are not called in ARM environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was an omission in transition to devm_xxx resource handling.
iounmap(udc->phy_regs) were removed, but ioremap() was left
without devm_.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Phy drivers and the ulpi interface providers depend on the
registration of the ulpi bus. Ulpi registers the bus in
module_init(). This could cause unnecessary bus users'
probe delays. i.e. unnecessary -EPROBE_DEFER happening on
ulpi_drivers in case they're registered before ulpi bus
itself.
Reported-by: Zhuo Qiuxu <qiuxu.zhuo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit
607af165c0 which removed some entries from the array and so made it
wrong to access the array by pin id.
The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.
This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.
Fixes: 607af165c0 ("pinctrl: i.MX27: Remove nonexistent pad definitions")
Cc: stable@vger.kernel.org
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible to hit a race condition if interrupts are generated on a GPIO
pin when the IRQ line in question is being disabled.
If the interrupt is freed, bcm2835_gpio_irq_disable() is called which
disables the event generation sources (edge, level). If an event occurred
between the last disabling of hard IRQs and the write to the event
source registers, a bit would be set in the GPIO event detect register
(GPEDSn) which goes unacknowledged by bcm2835_gpio_irq_handler()
so Linux complains loudly.
There is no per-GPIO mask register, so when disabling GPIO interrupts
write 1 to the relevant bit in GPEDSn to clear out any stale events.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver causes the kernel to hang on the R-Car gen2 SoC based boards
when the CPU_ALL_PORT() macro is fixed to reflect the reality, i.e. when the
GPIO space becomes actually sparse. This happens because the _GP_GPIO() macro
includes an indexed initializer which causes the "holes" (array entries filled
with all 0s) between the groups of the existing GPIOs; and the driver can't
cope with that. There seems to be no reason to use the indexed initializer,
so we can remove the index specifier and so avoid the "holes".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a21763a0b1
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two fairly simple fixes: one is a change that causes us to have a very low
queue depth leading to performance issues and the other is a null deref
occasionally in tapes thanks to use after put.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVq2/DAAoJEDeqqVYsXL0MhqoH/2ZlycWVQ2ZQyC9k2UWjAS7t
By0ufRZKeaxgwriVWZqTCE3QHfqqeR5tNNSvk26k+CJTS6nyVGX+g8cxLQJf1gey
DyAi9za+5P5SwYFuJxzULyZddTyeshoZplVvRwjd1/gnRUJXybuO+HRkYzaROd5e
7snX56jGt1MzpmIrO2wln24pFLVfdC5JivzUcXgYecHD/XZuzOEdZE1dCxONXy27
rTeqYayIGLFo7vhSt9J9ViF0QiU6ahCKmQ/TDsv3Sq1zg228E7DAmlzVAo2NCwLM
gelTRHRdO4rwwkehZH8QIdUI77MzgmwQIU4nZp3FBG9SWrIEPHaRpiDxCHr3UE0=
=bfE2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly simple fixes: one is a change that causes us to have a very
low queue depth leading to performance issues and the other is a null
deref occasionally in tapes thanks to use after put"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix host max depth checking for the 'queue_depth' sysfs interface
st: null pointer dereference panic caused by use after kref_put by st_open
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
Data is stored in the device in be16 format. Make use of be16_to_cpu and
cpu_to_be16 to have correct endianness on any host architecture.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio_device_register should be the last operation during probe. Therefor
move up interrupt setup code and while at it, change the check for invalid
values of client->irq to be smaller than zero.
Fixes: 3dd477acbd ("iio: light: Add threshold interrupt support for STK3310")
As the device_register makes the userspace interfaces of the device available
it is possible for requests to come in before the probe sequence has finished.
This can lead to unhandled interrupts and similar.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_EV_TYPE_THRESH in rising direction describes an event where the
threshold is crossed in rising direction, positive or negative values
being possible. This is not the case here.
Since the threshold is no signed value and only the magnitude is compared,
IIO_EV_TYPE_MAG is what describes the behaviour of these devices, see the
sysfs-bus-iio ABI Documentation.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On reading in_voltage_scale of we got an NULL pointer dereference Oops.
The reason for this is, that mcp320x_read_raw tries to access
chip_info->resolution from struct mcp320x, but chip_info is never set.
chip_info was never set since the driver was added, but there was no
acute problem, because it was not referenced.
The acute problem exists since
b12206e917
iio: adc: mcp320x. Add support for more ADCs
This patch fixes the issue by setting chip_info in mcp320x_probe.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Read the register only when the adc register address is 4 byte aligned.
(rather than the other way around).
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Cc: <Stable.vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Changed the offset to negative as usual equation is: (raw +
offset)*scale and in this
case offset should be negative (as we deduct 273.15 Kelvin to get temperature
in Celsius).
Signed-off-by: Crt Mori <cmo@melexis.com>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The RESET operation invoked in the last instance will align
in the natural way all 3 axis and the chip top view.
Without this, north and south are swapped.
Signed-off-by: Viorel Suman <viorel.suman@intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes setting the SET/RESET bit in the REG_CTRL0
register.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the debug/error string, the content of chip_id is supposed to
be output, rather than the return value of the previous operation.
Fixes: c91746a236 ("iio: magn: Add support for BMC150 magnetometer")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
bmc150_magn makes use of REGMAP_I2C, so select it to build always without
errors.
Fixes: c91746a236 ("iio: magn: Add support for BMC150 magnetometer")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sometimes bssid can go null on failed association.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes bssid can go null on failed association.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
only SAMP_FREQ is writable
Will lead to SAMP_FREQ being written by any attempt to write
to the other exported attributes and hence a rather unexpected
result!
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_preenable’:
drivers/iio/proximity/sx9500.c:682: warning: ‘ret’ may be used uninitialized in this function
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_predisable’:
drivers/iio/proximity/sx9500.c:706: warning: ‘ret’ may be used uninitialized in this function
If active_scan_mask is empty, it will loop once more over all channels,
doing nothing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The use of regmap in commit 2f2c96338a requires REGMAP_I2C to be selected, in
order to meet all dependencies.
Fixes: 2f2c96338a ("iio: ltr501: Add regmap support.")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When filling data->als_contr, the register content read into status needs
to be used, instead of the return status value of regmap_read.
Fixes: 8592a7eefa ("iio: ltr501: Add support for ltr559 chip")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The initial compensation was mistakingly toggling an extra bit in the
control register. Fix this and make sure it's less likely to happen by
introducing an additional macro.
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix error handling so that we can power the chip down even if a raw read
fails.
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the sampling frequencies according to the datasheet (page 8). The
datasheet specifies the following available frequencies for continuous
mode: 1.5 Hz, 13 Hz, 25 Hz, and 50 Hz.
Also fix comments about the ODR to comply with datasheet.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The stk3310 driver makes use of regmap_i2c, so this dependency needs to be
reflected in Kconfig.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In accordance with the recent proximity ABI changes,
STK3310's proximity readings should be un-inversed
in order to return low values for far-away objects
and high values for close ones.
As consequences of this change, iio event directions
have been switched and maximum proximity sensor
reference values have also been adjusted in accordance
with the real readings.
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Cosmic Circuits 10001 ADC driver depends on HAS_IOMEM, HAVE_CLK and
REGULATOR together, not just any of these.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
the millisecond values in tcs3414_times should be checked against
val2, not val, which is always zero.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Stephan Kleisinger <stephan.kleisinger@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In bmc150_accel_unregister_triggers() triggers should be unregistered in
reverse order of registration. Trigger registration starts with number 0,
counting up. In consequence, trigger number needs to be count down here.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When setting the bits for integration time, the appropriate bitmask needs
to be cleared first.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DT-Property "atmel,adc-startup-time" is stored in an u8 for a microsecond
value. When trying to increase the value of STARTUP in Register AT91_ADC_MR
some higher values can't be reached.
Change the type in function parameter and private structure field from u8 to
u32.
Signed-off-by: Jan Leupold <leupold@rsi-elektrotechnik.de>
[nicolas.ferre@atmel.com: change commit message, increase u16 to u32 for startup time]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The value sent on the SPI bus is shifted by an erroneous number of bits.
The shift value was already computed in the iio_chan_spec structure and
hence subtracting this argument to 16 yields an erroneous data position
in the SPI stream.
Signed-off-by: JM Friedt <jmfriedt@femto-st.fr>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Because of the ABI confusion proximity value exposed by SX9500
was inverted.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The gyroscope needs IIO_VAL_INT_PLUS_NANO for the scale channel and
unless specified write returns MICRO by default.
This needs to be properly specified so that write operations into scale
have the expected behaviour.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The module-data is currently missing. This includes the license-information
which makes the driver taint the kernel and miss symbols when compiled as
module.
Fixes: 44d6f2ef94 ("iio: adc: add driver for Rockchip saradc")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
By default all the sensors are runtime suspended state (lowest power
state). During Linux suspend process, all the run time suspended
devices are resumed and then suspended. This caused all sensors to
power up and introduced delay in suspend time, when we introduced
runtime PM for HID sensors. The opposite process happens during resume
process.
To fix this, we do powerup process of the sensors only when the request
is issued from user (raw or tiggerred). In this way when runtime,
resume calls for powerup it will simply return as this will not match
user requested state.
Note this is a regression fix as the increase in suspend / resume
times can be substantial (report of 8 seconds on Len's laptop!)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Len Brown <len.brown@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull irq fixes from Ingo Molnar:
"Misc irq fixes:
- two driver fixes
- a Xen regression fix
- a nested irq thread crash fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: Fix mapping of LPIs to collections
genirq: Prevent resend to interrupts marked IRQ_NESTED_THREAD
genirq: Revert sparse irq locking around __cpu_up() and move it to x86 for now
gpio/davinci: Fix race in installing chained irq handler
Merge fixes from Andrew Morton:
"25 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (25 commits)
lib/decompress: set the compressor name to NULL on error
mm/cma_debug: correct size input to bitmap function
mm/cma_debug: fix debugging alloc/free interface
mm/page_owner: set correct gfp_mask on page_owner
mm/page_owner: fix possible access violation
fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
/proc/$PID/cmdline: fixup empty ARGV case
dma-debug: skip debug_dma_assert_idle() when disabled
hexdump: fix for non-aligned buffers
checkpatch: fix long line messages about patch context
mm: clean up per architecture MM hook header files
MAINTAINERS: uclinux-h8-devel is moderated for non-subscribers
mailmap: update Sudeep Holla's email id
Update Viresh Kumar's email address
mm, meminit: suppress unused memory variable warning
configfs: fix kernel infoleak through user-controlled format string
include, lib: add __printf attributes to several function prototypes
s390/hugetlb: add hugepages_supported define
mm: hugetlb: allow hugepages_supported to be architecture specific
revert "s390/mm: make hugepages_supported a boot time decision"
...
Drivers:
- fix mt6397 wakealarm creation
- remove a compilation warning for armada38x that was forgotten
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=l6li
-----END PGP SIGNATURE-----
Merge tag 'rtc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull rtc fixes from Alexandre Belloni:
"A few fixes for the RTC susbsystem for 4.2.
The mt6397 driver was introduce in 4.2 so it is worth fixing before
the final release. I though the compilation warning for armada38x was
fixed by akpm in commit f98b733e93 ("rtc-armada38x.c: remove unused
local `flags'") but he actually missed some occurrences of the
variables. Since I received 4 patches for that, I think we can
include it now.
Summary:
- fix mt6397 wakealarm creation
- remove a compilation warning for armada38x that was forgotten"
* tag 'rtc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: armada38x: Remove unused variable from armada38x_rtc_set_time()
rtc: mt6397: enable wakeup before registering rtc device
increase and adversely impact both throughput and system load
- Fix for a use after free bug in DM core's device cleanup
- A couple DM btree removal fixes (used by dm-thinp)
- A DM thinp fix for order-5 allocation failure
- A DM thinp fix to not degrade to read-only metadata mode when in
out-of-data-space mode for longer than the 'no_space_timeout'
- Fix a long-standing oversight in both dm-thinp and dm-cache by
now exporting 'needs_check' in status if it was set in metadata
- Fix an embarrassing dm-cache busy-loop that caused worker threads to
eat cpu even if no IO was actively being issued to the cache device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVqUfSAAoJEMUj8QotnQNa+RUH+wXrHCGI6J7RHIXVd5igP9K0
yFZGEnLZe6Ebt5CACLcKn/qN0g97iwCrlcxFt+1Gj/GbW1GIQzs7vg38La3PZxWZ
jAkI3JMY816bP1x3VK1HtMsk2gRaE/hh0gxK5pPLB9a+ZdEsz9UML0rs+JseOdn3
n+454dhwOyChwz7zFEbpn+mfjoruFScGX0Y2qaSHBV/xMhmExpthw9V1yFC2v2tW
8cAHOMDLNLHhR5adF9YxjZH8wILbyYK9oPy3iGhj/TF/Dx7saWYG4UlnL5xIOLsB
5WK9gRrJJ/Wf0FsDdN88AaY4Bdpj4esS2JeTZpvujxeBb7ZNeJoCUqyzggURv/c=
=hCjo
-----END PGP SIGNATURE-----
Merge tag 'dm-4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- revert a request-based DM core change that caused IO latency to
increase and adversely impact both throughput and system load
- fix for a use after free bug in DM core's device cleanup
- a couple DM btree removal fixes (used by dm-thinp)
- a DM thinp fix for order-5 allocation failure
- a DM thinp fix to not degrade to read-only metadata mode when in
out-of-data-space mode for longer than the 'no_space_timeout'
- fix a long-standing oversight in both dm-thinp and dm-cache by now
exporting 'needs_check' in status if it was set in metadata
- fix an embarrassing dm-cache busy-loop that caused worker threads to
eat cpu even if no IO was actively being issued to the cache device
* tag 'dm-4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: avoid calls to prealloc_free_structs() if possible
dm cache: avoid preallocation if no work in writeback_some_dirty_blocks()
dm cache: do not wake_worker() in free_migration()
dm cache: display 'needs_check' in status if it is set
dm thin: display 'needs_check' in status if it is set
dm thin: stay in out-of-data-space mode once no_space_timeout expires
dm: fix use after free crash due to incorrect cleanup sequence
Revert "dm: only run the queue on completion if congested or no requests pending"
dm btree: silence lockdep lock inversion in dm_btree_del()
dm thin: allocate the cell_sort_array dynamically
dm btree remove: fix bug in redistribute3
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some modules call config_item_init_type_name() and config_group_init_type_name()
with parameter "name" directly controlled by userspace. These two
functions call config_item_set_name() with this name used as a format
string, which can be used to leak information such as content of the
stack to userspace.
For example, make_netconsole_target() in netconsole module calls
config_item_init_type_name() with the name of a newly-created directory.
This means that the following commands give some unexpected output, with
configfs mounted in /sys/kernel/config/ and on a system with a
configured eth0 ethernet interface:
# modprobe netconsole
# mkdir /sys/kernel/config/netconsole/target_%lx
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# echo 1 > /sys/kernel/config/netconsole/target_%lx/enabled
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# dmesg |tail -n1
[ 142.697668] netconsole: target (target_ffffffffc0ae8080) is
enabled, disable to update parameters
The directory name is correct but %lx has been interpreted in the
internal item name, displayed here in the error message used by
store_dev_name() in drivers/net/netconsole.c.
To fix this, update every caller of config_item_set_name to use "%s"
when operating on untrusted input.
This issue was found using -Wformat-security gcc flag, once a __printf
attribute has been added to config_item_set_name().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the 'flags' variable in order to fix the following warning:
drivers/rtc/rtc-armada38x.c:91:22: warning: unused variable 'flags' [-Wunused-variable]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_sysfs_add_device checks if device can wakeup before creating the
wakealarm file in sysfs. Thus the driver must set wakeup capability
before registering the rtc device.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Here's some staging and IIO driver fixes for 4.2-rc3.
Nothing major, the majority are IIO issues that were reported, with a
few other minor staging driver fixes. All have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWpRFUACgkQMUfUDdst+yke/wCeJPDuYuOp/SFhyviMx9ojKIGF
kVIAoI1xDY4SwVExztXcqyKo6m0H2yZ4
=pxAa
-----END PGP SIGNATURE-----
Merge tag 'staging-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here's some staging and IIO driver fixes for 4.2-rc3.
Nothing major, the majority are IIO issues that were reported, with a
few other minor staging driver fixes. All have been in linux-next for
a while with no reported issues"
* tag 'staging-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (25 commits)
staging: vt6656: check ieee80211_bss_conf bssid not NULL
staging: vt6655: check ieee80211_bss_conf bssid not NULL
staging:lustre: remove irq.h from socklnd.h
staging: make board support depend on OF_IRQ and CLKDEV_LOOKUP
iio: tmp006: Check channel info on write
iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
iio:light:ltr501: fix regmap dependency
iio:light:ltr501: fix variable in ltr501_init
iio: sx9500: fix bug in compensation code
iio: sx9500: rework error handling of raw readings
iio: magnetometer: mmc35240: fix available sampling frequencies
iio:light:stk3310: Fix REGMAP_I2C dependency
iio: light: STK3310: un-invert proximity values
iio:adc:cc10001_adc: fix Kconfig dependency
iio: light: tcs3414: Fix bug preventing to set integration time
iio:accel:bmc150-accel: fix counting direction
iio:light:cm3323: clear bitmask before set
iio: adc: at91_adc: allow to use full range of startup time
iio: DAC: ad5624r_spi: fix bit shift of output data value
iio: proximity: sx9500: Fix proximity value
...
Here's some USB driver fixes for 4.2-rc3.
The ususal number of gadget driver fixes are in here, along with some
new device ids and a build fix for the mn10300 arch which required some
symbols to be renamed in the mos7720 driver.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWpRQEACgkQMUfUDdst+ykQTACfbXmLNn/1ycArRysqHGg5llIZ
pdIAn2Yi8TCbXr9HvtugUcxQrDIANNcF
=WUtC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here's some USB driver fixes for 4.2-rc3.
The ususal number of gadget driver fixes are in here, along with some
new device ids and a build fix for the mn10300 arch which required
some symbols to be renamed in the mos7720 driver.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: Destroy serial_minors IDR on module exit
usb: gadget: f_midi: fix error recovery path
usb: phy: mxs: suspend to RAM causes NULL pointer dereference
usb: gadget: udc: fix free_irq() after request_irq() failed
usb: gadget: composite: Fix NULL pointer dereference
usb: gadget: f_fs: do not set cancel function on synchronous {read,write}
usb: f_mass_storage: limit number of reported LUNs
usb: dwc3: core: avoid NULL pointer dereference
usb: dwc2: embed storage for reg backup in struct dwc2_hsotg
usb: dwc2: host: allocate qtd before atomic enqueue
usb: dwc2: host: allocate qh before atomic enqueue
usb: musb: host: rely on port_mode to call musb_start()
USB: cp210x: add ID for Aruba Networks controllers
USB: mos7720: rename registers
USB: option: add 2020:4000 ID
hitting individual drivers and nothing else.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mTd/
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"This is a first set of GPIO fixes for the v4.2 series, all hitting
individual drivers and nothing else (except for a documentation
oneliner. I intended to send a request earlier but life intervened)"
* tag 'gpio-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: fix nested irqs rescheduling
gpio: omap: prevent module from being unloaded while in use
gpio: max732x: Add missing dev reference to gpiochip
gpio/xilinx: Use correct address when setting initial values.
gpio: zynq: Fix problem with unbalanced pm_runtime_enable
gpio: omap: add missed spin_unlock_irqrestore in omap_gpio_irq_type
gpio: brcmstb: fix null ptr dereference in driver remove
gpio: Remove double "base" in comment
Pull drm fixes from Dave Airlie:
"Fixes all over the place.
The rockchip and imx fixes I missed while on holidays, so I've queued
them now which makes this a bit bigger.
The rest is misc amdgpu, radeon, i915 and armada.
I think the most important thing is the ioctl fix, we dropped the
avoid compat ball, so we get to add a compat wrapper.
There is also an i915 revert to avoid a regression with existing
userspace"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (43 commits)
drm/ttm: improve uncached page deallocation.
drm/ttm: fix uncached page deallocation to properly fill page pool v3.
drm/amdgpu/dce8: Re-set VBLANK interrupt state when enabling a CRTC
drm/radeon/ci: silence a harmless PCC warning
drm/amdgpu/cz: silence some dpm debug output
drm/amdgpu/cz: store the forced dpm level
drm/amdgpu/cz: unforce dpm levels before forcing to low/high
drm/amdgpu: remove bogus check in gfx8 rb setup
drm/amdgpu: set proper index/data pair for smc regs on CZ (v2)
drm/amdgpu: disable the IP module if early_init returns -ENOENT (v2)
drm/amdgpu: stop context leak in the error path
drm/amdgpu: validate the context id in the dependencies
drm/radeon: fix user ptr race condition
drm/radeon: Don't flush the GART TLB if rdev->gart.ptr == NULL
drm/radeon: add a dpm quirk for Sapphire Radeon R9 270X 2GB GDDR5
drm/armada: avoid saving the adjusted mode to crtc->mode
drm/armada: fix overlay when partially off-screen
drm/armada: convert overlay to use drm_plane_helper_check_update()
drm/armada: fix gem object free after failed prime import
drm/armada: fix incorrect overlay plane cleanup
...
The GICv3 ITS architecture allows a given [DevID, EventID] pair to be
translated to a [LPI, Collection] pair, where DevID is the device writing
the MSI, EventID is the payload being written, LPI is the actual
interrupt number, and Collection is roughly equivalent to a target CPU.
Each LPI can be mapped to a separate collection, but the ITS driver
insists on maintaining the collection on a device basis, instead of doing
it on a per interrupt basis.
This is obviously flawed, and this patch fixes it by adding a per interrupt
index that indicates which collection number is in use.
Reported-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # 4.1, 4.0
Link: http://lkml.kernel.org/r/1437126402-11677-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* fix a crash in time events
* fix a crash in PCIe transport
* fix BT Coex code that prevented association on certain
devices (3160).
* revert the new RBD allocation model because it introduced
a bug when running on weak VM setups.
* a new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVop0oAAoJEC0Llv5uNjIBgCkP/ic9hgwZzh3nWzfYyqvxTEY0
NrLxW8jJGIYxS/M3tVoG8xQcoeA4D4itRt5npLGU+NiqxZMZWOsMRQTKLp04dAQE
WuSDvBsiR0LFCv+XIccp63LYjDA/Y4Ib8zJTLIdMbQONBJ9lvy2CM5Qe98nzxkxr
tkawZZrfUigPWCWoqjx1+uENCf6N/pJEnovZuWdRVSxj+olVjNs4CRcZeMAF1C44
SBvImKa2JyGqPa1Zpr2nCRmyN/I9yvh6kCjyC5ywClm3vkd4ACXtaiNjtrlKwli8
LhFSFBUFeDd+OJujS4/YoUzSojaNZYiOoN9NLmeFojD8kIkO47ClvjSdGrzOekm/
fCNiIY9IYvtTOkJg5vQtu5/eXP/da7ZknQPjfswKvfWfuaUk8GhLNXghnZ+OnQYQ
OT5oqOT5WTQObLwiANcpOPqFuUQMuTu/JGUBI5Ex3XIGWgCQFiIZJJUBshAas70l
j340Jw9l5FKlhff+e3b57h928Ub4hnxgycy6E66/kXCYPOje4bSnE7LX1MUPa58V
oc4Bd2kiL1BEFuuzkaYLBqlwwYv2qqfeh6oWz+4slCkorzm0UTMNvlQjGQgZkZIP
9V7j/SAGL2Cwo7Wd4xSrQ6s+kF1pI9hbK/ABo6qw/ZgIWmt6YJnQF05ez4ZJdzFx
X/AOFvHACngGZ2tavxJU
=TLrS
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-06-12' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* bug fixes specific for 8000 series
* fix a crash in time events
* fix a crash in PCIe transport
* fix BT Coex code that prevented association on certain
devices (3160).
* revert the new RBD allocation model because it introduced
a bug when running on weak VM setups.
* a new device IDs
Calls to set_memory_wb() incure heavy TLB flush and IPI cost. To
minimize those wait until pool grow beyond batch size before
draining the pool.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-and-Tested-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Current code never allowed the page pool to actualy fill in anyway.
This fix it, so that we only start freeing page from the pool when
we go over the pool size.
Changed since v1:
- Move the page batching optimization to its separate patch.
Changed since v2:
- Do not remove code part of the batching optimization with
this patch.
- Better commit message.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-and-Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since 9a2c1c3b91 ("pinctrl: samsung: Allow grouping multiple
pinmux/pinconf nodes") the defines for GPIO group and function names are
not used anywhere in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Inspired-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
First, dma_sync_single_for_cpu() shouldn't have been called in the first place
(it's a streaming DMA API), dma_unmap_single() should have been called instead.
Second, dma_unmap_single() call after handing the buffer to napi_gro_receive()
makes little sense. Moreover desc->dptr might not be valid at this point.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a recently introduced issue in the cpufreq policy object
reinitialization that leads to CPU offline/online breakage
(Viresh Kumar).
- Make it possible to access frequency tables of offline CPUs
which is needed by thermal management code among other things
(Viresh Kumar).
- Fix an ACPI resource management regression introduced during
the 4.0 cycle that may cause incorrect resource validation
results to appear in 32-bit x86 kernels due to silent truncation
of 64-bit values to 32-bit (Jiang Liu).
- Fix up an RCU-related lockdep complaint about suspicious RCU
usage in idle caused by using a suspend tracepoint in the
core suspend-to-idle code (Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BDs+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two bugs in the cpufreq core (including one recent
regression), fix a 4.0 PCI regression related to the ACPI resources
management and quieten an RCU-related lockdep complaint about a
tracepoint in the suspend-to-idle code.
Specifics:
- Fix a recently introduced issue in the cpufreq policy object
reinitialization that leads to CPU offline/online breakage (Viresh
Kumar)
- Make it possible to access frequency tables of offline CPUs which
is needed by thermal management code among other things (Viresh
Kumar)
- Fix an ACPI resource management regression introduced during the
4.0 cycle that may cause incorrect resource validation results to
appear in 32-bit x86 kernels due to silent truncation of 64-bit
values to 32-bit (Jiang Liu)
- Fix up an RCU-related lockdep complaint about suspicious RCU usage
in idle caused by using a suspend tracepoint in the core suspend-
to-idle code (Rafael J Wysocki)"
* tag 'pm+acpi-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
Fix SMBIOS call handling and hwswitch state coherency in the dell-laptop driver.
Cleanups for intel_*_ipc drivers.
dell-laptop:
- Do not cache hwswitch state
- Check return value of each SMBIOS call
- Clear buffer before each SMBIOS call
intel_scu_ipc:
- Move local memory initialization out of a mutex
intel_pmc_ipc:
- Update kerneldoc formatting
- Fix compiler casting warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVqCrgAAoJEKbMaAwKp364aBcIALo/ZB6JFFd3oFDBbZR9bzvp
senrgC2QSWboFlyJ2aHB09n98m6tR5x8HTE6BijT64bUyPSLTPgDZoeC9ezIu1H0
rXKJZM7GduxYVOvVgOPVKqt/yUopI55jDhpgvFmxpXgp9zaz4our2y+93VCCBkIm
9nJMHXIvK+Rg4Rg0MuEkaghLRFivJAYFuyFu6vgWQOGap1QXruPIylK6agZs2E9x
KhJAlLNjoAAfqFFkWdk7PxMO8QIgV9pLU8RlOQmUdRSe8F+CI3AAJjdn+FdPoXFN
EBirxMm8NAd9+/JlfU95fUBwPnofY+D3Q8jUyKBBxnZbDQMIA6gWtzGaA/BY/zI=
=hpkC
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.2-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix SMBIOS call handling and hwswitch state coherency in the
dell-laptop driver. Cleanups for intel_*_ipc drivers. Details:
dell-laptop:
- Do not cache hwswitch state
- Check return value of each SMBIOS call
- Clear buffer before each SMBIOS call
intel_scu_ipc:
- Move local memory initialization out of a mutex
intel_pmc_ipc:
- Update kerneldoc formatting
- Fix compiler casting warnings"
* tag 'platform-drivers-x86-v4.2-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_scu_ipc: move local memory initialization out of a mutex
intel_pmc_ipc: Update kerneldoc formatting
dell-laptop: Do not cache hwswitch state
dell-laptop: Check return value of each SMBIOS call
dell-laptop: Clear buffer before each SMBIOS call
intel_pmc_ipc: Fix compiler casting warnings
If no work was performed then prealloc_data_structs() wasn't ever called
so there isn't any need to call prealloc_free_structs().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Refactor writeback_some_dirty_blocks() to avoid prealloc_data_structs()
if the policy doesn't have any dirty blocks ready for writeback.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
All methods that queue work call wake_worker() as you'd expect.
E.g. cell_defer, defer_bio, quiesce_migration (which is called by
writeback, promote, demote_then_promote, invalidate, discard, etc).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
These patches fix the parallel-display driver to use the standard OF
graph bindings for connecting a drm_panel via device tree instead of
an undocumented, driver specific device tree property, take care to
disable all IPU interrupts before setting up the irq chip to fix a
kexec lockup, and fix VGA output on i.MX53-QSB boards by correcting
the media bus format set by the imx-tve driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pGBQ
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-fixes-2015-07-14' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm: fixes for parallel-display, imx-tve, and ipu-common
These patches fix the parallel-display driver to use the standard OF
graph bindings for connecting a drm_panel via device tree instead of
an undocumented, driver specific device tree property, take care to
disable all IPU interrupts before setting up the irq chip to fix a
kexec lockup, and fix VGA output on i.MX53-QSB boards by correcting
the media bus format set by the imx-tve driver.
* tag 'imx-drm-fixes-2015-07-14' of git://git.pengutronix.de/git/pza/linux:
drm/imx: tve: fix media bus format for VGA output
GPU: ipu: fix lockup caused by pending chained interrupts
drm/imx: parallel-display: fix drm_panel support
A range of fixes for the Armada DRM driver:
- A missing wakeup could result in overlay frames being delayed, causing
video playback to hiccup.
- Avoid unmapping a dma-buf attachment which was never mapped
- Fix the overlay when partially off the screen by switching to the
drm_plane_helper_check_update() helper and using the calculated
coordinates to set the start address.
- Remove an incorrect assignment to crtc->mode - which should be the
unadjusted mode.
- Fix a missing call to drm_plane_cleanup() in the overlay code.
* 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/armada: avoid saving the adjusted mode to crtc->mode
drm/armada: fix overlay when partially off-screen
drm/armada: convert overlay to use drm_plane_helper_check_update()
drm/armada: fix gem object free after failed prime import
drm/armada: fix incorrect overlay plane cleanup
drm/armada: fix missing overlay wake-up
Next batch of i915 fixes. Note that the compat32 patch here needs the drm
core one to be actually useful, I'll send you that one with a separate
drm-fixes pull request. One revert because a fix in -rc2 did break
existing userspace.
* tag 'drm-intel-fixes-2015-07-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Do not call intel_crtc_disable if the crtc is already disabled.
Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"
drm/i915: Forward all core DRM ioctls to core compat handling
drm/i915: fix oops in primary_check_plane
drm/i915: remove unused has_dma_mapping flag
drm/i915: Fix missing return warning for !CONFIG_DEBUGFS
drm/i915: avoid leaking DMA mappings
drm/i915: Snapshot seqno of most recently submitted request.
drm/i915: Store device pointer in contexts for late tracepoint usafe
Ok next attempt at drm-fixes pull. Big thing really is just the compat32
one for addfb2.1.
* tag 'topic/drm-fixes-2015-07-16' of git://anongit.freedesktop.org/drm-intel:
drm: Provide compat ioctl for addfb2.1
Documentation: drm: Fix tablulation in KMS properties table
drm: add a check for x/y in drm_mode_setcrtc
drm/rockchip: use drm_gem_mmap helpers
Pull block fixes from Jens Axboe:
"A collection of fixes from the last few weeks that should go into the
current series. This contains:
- Various fixes for the per-blkcg policy data, fixing regressions
since 4.1. From Arianna and Tejun
- Code cleanup for bcache closure macros from me. Really just
flushing this out, it's been sitting in another branch for months
- FIELD_SIZEOF cleanup from Maninder Singh
- bio integrity oops fix from Mike
- Timeout regression fix for blk-mq from Ming Lei"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: set default timeout as 30 seconds
NVMe: Reread partitions on metadata formats
bcache: don't embed 'return' statements in closure macros
blkcg: fix blkcg_policy_data allocation bug
blkcg: implement all_blkcgs list
blkcg: blkcg_css_alloc() should grab blkcg_pol_mutex while iterating blkcg_policy[]
blkcg: allow blkcg_pol_mutex to be grabbed from cgroup [file] methods
block/blk-cgroup.c: free per-blkcg data when freeing the blkcg
block: use FIELD_SIZEOF to calculate size of a field
bio integrity: do not assume bio_integrity_pool exists if bioset exists
* pm-cpuidle:
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
* pm-cpufreq:
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
* acpi-resources:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
The regulator_resolve_supply() function calls set_supply() which in turn
calls create_regulator() to allocate a supply regulator.
If an error occurs after set_supply() succeeded, the allocated regulator
has to be freed before propagating the error code.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexei Potashnik
Swapnil Nagle
Roland Dreier
Kanoj Sarcar
Himanshu Madhani
Quinn Tran
Saurav Kashyap
Alex Williamson
Linus Torvalds
Bastien Nocera
Dmitry Torokhov
Devesh Sharma
Jason Gunthorpe
Steve Wise
Mark Brown
Sascha Hauer
Jingju Hou
Dong Aisheng
Joakim Tjernlund
Tomas Winkler
Geert Uytterhoeven
Peng Fan
Vignesh R
Kishon Vijay Abraham I
David Disseldorp
Andy Grover
Nicholas Mc Guire
Dave Airlie
NeilBrown
Goldwyn Rodrigues
Goldwyn Rodrigues
Alexandre Courbot
Peter Hurley
David Jander
Bo Svangård
Jakub Kicinski
Axel Lin
Dongxing Zhang
Krzysztof Kozlowski
Bernhard Bender
Greg Kroah-Hartman
Alex Deucher
Leo Liu
Michel Dänzer
Luis Henriques
Sudeep Dutt
Sudip Mukherjee
Alan Stern
Johannes Thumshirn
Hans de Goede
Oliver Neukum
Lu Baolu
Zhuang Jin Can
Brian Campbell
AMAN DEEP
Rajmohan Mani
Mathias Nyman
Mike Krinkin
John Youn
Daniel Vetter
Sergei Shtylyov
Dan Murphy
David S. Miller
Mugunthan V N
Chris Wilson
Ingo Molnar
Luis R. Rodriguez
Simon Guinot
Joachim Eastwood
Shaohui Xie
Reinhard Speyerer
Karicheri, Muralidharan
dingtianhong
Florian Fainelli
Nikolay Aleksandrov
Boris Brezillon
Vivien Didelot
Michael S. Tsirkin
Yoshihiro Shimoda
Alexey Khoroshilov
Uwe Kleine-König
Jonathan Bell
Grygorii Strashko
Linus Walleij
Hartmut Knaack
Martin Kepplinger
Manfred Schlaegl
Fugang Duan
Crt Mori
Viorel Suman
Daniel Baluta
Malcolm Priestley
Peter Meerwald
Vlad Dogaru
Teodora Baluta
Tiberiu Breana
Jan Leupold
JM Friedt
Adriana Reus
Fabio Estevam
Heiko Stuebner
Srinivas Pandruvada
Viresh Kumar
Nicolas Iooss
Wei-Ning Huang
Marc Zyngier
Kalle Valo
Jérôme Glisse
Krzysztof Kozlowski
Mike Snitzer
Rafael J. Wysocki
Javier Martinez Canillas