Commit Graph

161 Commits

Author SHA1 Message Date
Daniel Mack 8d0df7a3d1 drivers/w1/masters/w1-gpio.c: fix read_bit()
W1 master implementations are expected to return 0 or 1 from their
read_bit() function.  However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't.  Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-12 16:20:23 -07:00
Herton Ronaldo Krzesinski 8ca2f156b0 w1: add missing Kconfig/Makefile entries for DS2431 slave driver
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-27 16:26:21 -08:00
Ben Gardner dca17146f4 w1_ds2433: clear the validcrc flag after a write
The w1_ds2433 driver does not read from the hardware if the CRC was valid
on the last read.  The validcrc flag should be cleared after a write so
that the new value can be read.

Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-27 16:26:20 -08:00
Ian Dall 507e2fbaaa w1: w1 temp calculation overflow fix
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12646

When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees.  These are bothe well within the -55 - +125 degree
range for the sensor.

Fix overflow in left-shift of a u8.

Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-11 14:25:37 -08:00
Evgeniy Polyakov 4037014e3f w1: send status messages after command processing
Send completion status of the commands to the userspace.  Message and
protocol are described in the documentation.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:14 -08:00
Evgeniy Polyakov f89735c4e2 w1: added w1 reset command
Command which allows to reset the bus.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:14 -08:00
Evgeniy Polyakov 325a06fb13 w1: move w1 commands from defines to enum
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:13 -08:00
Evgeniy Polyakov c7e26631d2 w1: allow master IO commands
This small patchset extendes existing commands with reset, master IO and
status messages.  Reset is used to reset the bus for given master device,
master IO command allows to initiate IO against bus itself not selecting
slave device first, which can be used to probe the device for example.
And status messages carry command completion status back to the userspace
(namely very useful to get -ENODEV from when requested device was not
found).

Great thanks to Paul Alfille of OWFS for testing and commands suggestions.

This patch:

Allow starting of IO not against already found slave devices, but against
the bus itself, which can be used for example to probe devices.

[akpm@linux-foundation.org: reindent switch statements]
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:13 -08:00
Evgeniy Polyakov 3b8384070e w1: list slaves commands
Initiates search (or alarm search) and returns all found devices to
userspace.  Found devices are not added into the system (i.e.  they are
not attached to family devices or bus masters), it will be done via (if
was not done yet) usual timed searching.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:13 -08:00
Evgeniy Polyakov 9be62e0b2f w1: add touch block command
Writes and returns sampled data back to userspace.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:13 -08:00
Evgeniy Polyakov 610705e780 w1: add list masters w1 command
This patch series introduces and extends several userspace commands
used with netlink protocol.

Touch block command allows to write data and return sampled data to
the userspace.

Extended search and alarm seach commands to return list of slave
devices found during given search.

List masters command allows to send all registered master IDs to the
userspace.

Great thanks to Paul Alfille (owfs) who
tested this implementation and wrote w1-to-network daemon
http://sourceforge.net/projects/w1repeater/ and

Frederik Deweerdt and Randy Dunlap for review.

This patch:

Returns list of registered bus master devices.

Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Cc: Frederik Deweerdt <frederik.deweerdt@xprog.eu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:13 -08:00
Sascha Hauer a5fd9139f7 w1: add 1-wire master driver for i.MX27 / i.MX31
This patch adds support for the 1-wire master interface for i.MX27 and
i.MX31.

Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-08 08:31:13 -08:00
Kay Sievers 40f91de6a1 w1: struct device - replace bus_id with dev_name(), dev_set_name()
CC: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-06 10:44:34 -08:00
Evgeniy Polyakov f00a189257 w1: fix slave selection on big-endian systems
During test of the w1-gpio driver i found that in "w1.c:679
w1_slave_found()" the device id is converted to little-endian with
"cpu_to_le64()", but its not converted back to cpu format in "w1_io.c:293
w1_reset_select_slave()".

Based on a patch created by Andreas Hummel.

[akpm@linux-foundation.org: remove unneeded cast]
Reported-by: Andreas Hummel <andi_hummel@gmx.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-23 15:58:21 -08:00
Al Viro 2fceab0bd8 W1_MASTER_DS1WM should depend on HAVE_CLK
Uses clk_...() a lot

Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-30 10:03:36 -08:00
Stanley.Miao 06b0d4dc14 W1 OMAP: Fix OMAP LDP boot crash
OMAP LDP boot crash.  This is because w1 subsystem changed the search
interface, so update omap_hdq's search interface to follow the change.

Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-19 18:50:00 -08:00
Madhusudhan Chikkature cfbc619033 hdq: bQ27000 HDQ Slave Interface Driver
Provide the BQ27000 slave interface driver.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-12 17:17:18 -08:00
Madhusudhan Chikkature 9f2bc79f7d hdq driver for OMAP2430/3430
The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols.  These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).

This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-12 17:17:18 -08:00
Madhusudhan Chikkature 34e453d455 w1: export w1_read_8 function
Export the w1_read_8 function for use of drivers.  The OMAP HDQ
driver(drivers/w1/masters/omap_hdq.c) uses this function.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-12 17:17:18 -08:00
Parag Warudkar 01e8ef11bc x86: sysfs: kill owner field from attribute
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary.  But the field was left in the structure to
ease the merge.  It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!

This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 .  We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test.  Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.

akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'.  But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.

[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:42 -07:00
Bernhard Weirich d827367472 w1: new driver. DS2431 chip
[akpm@linux-foundation.org: minor fixlets and cleanups]
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:51 -07:00
David Fries ade6d810b5 W1: ds2490.c optimize ds_set_pullup
Optimize the ds_set_pullup function.  For a strong pullup to be sent the
ds2490 has to have both the strong pullup mode enabled, and the specific
write operation has to have the SPU bit enabled.  Previously the write
always had the SPU bit enabled and both the duration and model was set
when a strong pullup was requested.  Now the strong pullup mode is enabled
at initialization time, the delay is updated only when the value changes,
and the write SPU bit is set only when a strong pullup is required.  This
removes two or three bus transactions per strong pullup request.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:51 -07:00
David Fries cbf4a49afa W1: ds2490.c ds_write_block remove extra ds_wait_status
Drop the extra ds_wait_status() in ds_write_block().

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:51 -07:00
David Fries 19e7184f75 W1: ds2490.c magic number work
This replaces some magic numbers with marcos and corrects one marco.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:51 -07:00
David Fries e464af2473 W1: ds2490.c reset ds2490 in init
Reset the device in init as it can be in a bad state.  This is necessary
because a block write will wait for data to be placed in the output buffer
and block any later commands which will keep accumulating and the device
will not be idle.  Another case is removing the ds2490 module while a bus
search is in progress, somehow a few commands get through, but the input
transfers fail leaving data in the input buffer.  This will cause the next
read to fail see the note in ds_recv_data.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:51 -07:00
David Fries 7a4b9706ed W1: ds2490.c ds_reset remove ds_wait_status
ds_reset no longer calls ds_wait_status, the result wasn't used and it
would only delay the following data operations.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:51 -07:00
David Fries 4b9cf1bc32 W1: ds2490.c ds_dump_status rework
- add result register #defines
- rename ds_dump_status to ds_print_msg
- rename ds_recv_status to ds_dump_status
- ds_dump_status prints the requested status and no longer reads the
  status, this is because the second status read can return different
  data for example the result register
- the result register will be printed, though limited to detecting a
  new device, detecting other values such as a short would require
  additional reporting methods
- ST_EPOF was moved to ds_wait_status to clear the error condition
  sooner

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:51 -07:00
David Fries 6e10f65427 W1: ds2490.c simplify and fix ds_touch_bit
Simplify and fix ds_touch_bit.  If a device is attached in the middle of a
bus search the status register will return more than the default 16 bytes.
 The additional bytes indicate that it has detected a new device.  The way
ds_wait_status is coded, if it doesn't read 16 status bytes it returns an
error value.  ds_touch_bit then will detect that error and return an
error.  In that case it doesn't read the input buffer and returns
uninitialized data.  It doesn't stop there.  The next transaction will not
expect the extra byte in the input buffer and the short read will cause an
error and clear out both the old byte and new data in the input buffer.

Just ignore the value of ds_wait_status.  It is still required to wait
until ds2490 is again idle and there is data to read when ds_recv_data is
called.  This also removes the while loop.  None of the other commands
wait and verify that the issued command is in the status register.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries a08e2d338b W1: ds2490.c disable bit read and write
Don't export read and write bit operations, they didn't work, they weren't
used, and they can't be made to work.  The one wire low level bit
operations expect to set high or low levels, the ds2490 hardware only
supports complete read or write time slots, better to just comment them
out.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries e1c86d226d W1: ds2490.c ds_write_bit, grouping error, disable readback
ds_write_bit doesn't read the input buffer, so add COMM_ICP and a comment
that it will no longer generate a read back data byte.  If there is an
extra data byte later on then it will cause an error and discard what data
was there.  Corrected operator ordering for ds_send_control.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries 1f4ec2d7f6 W1: ds2490.c add support for strong pullup
Add strong pullup support for ds2490 driver, also drop mdelay(750), which
busy waits, usage in favour of msleep for long delays.  Now with msleep
only being called when the strong pullup is active, one wire bus
operations are only taking minimal system overhead.

The new set_pullup will only enable the strong pullup when requested,
which is expected to be the only write operation that will benefit from a
strong pullup.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries 95cfaebf61 W1: ds2490.c correct print message
Corrected print message, it was writing not reading, this also prints the
endpoint used for the write instead of hardcoding it.  Failed to write
1-wire data to ep0x%x: err=%d.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries cadd486cfc W1: ds1wm.c msleep for reset
Like the previous w1_io.c reset coments and msleep patch, I don't have the
hardware to verify the change, but I think it is safe.  It also helps to
see a comment like this in the code.  "We'll wait a bit longer just to be
sure." If they are going to calculate delaying 324.9us, but actually delay
500us, why not just give up the CPU and sleep?  This is designed for a
battery powered ARM system, avoiding busywaiting has to be good for
battery life.

I sent a request for testers March 7, 2008 to the Linux kernel mailing
list and two developers who have patches for ds1wm.c, but I didn't get
any respons.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries 8e3dae2b47 W1: w1_io.c reset comments and msleep
w1_reset_bus, added some comments about the timing and switched to msleep
for the later delay.  I don't have the hardware to test the sleep after
reset change.  The one wire doesn't have a timing requirement between
commands so it is fine.  I do have the USB hardware and it would be in big
trouble with 10ms interrupt transfers to find that the reset completed.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries 7dc8f527ef W1: w1.c s/printk/dev_dbg/
s/printk/dev_dbg/

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries af00a2d5a0 W1: w1_int.c use first available master number
Follow the example of other devices (like the joystick device).  Pick the
first available id for each detected device.  Currently for USB devices,
suspending and resuming would cause the number to increment.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries e0d29c7699 W1: w1_therm consistent mutex access code cleanup
sl->master->mutex and dev->mutex refer to the same mutex variable, but be
consistent and use the same set of pointers for the lock and unlock calls.
 It is less confusing (and one less pointer dereference this way).

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries fe3cb82364 W1: w1_family, remove unused variable need_exit
Removed the w1_family structure member variable need_exit.  It was only
being set and never used.  Even if it were to be used it is a polling type
operation.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries 347ba8a588 W1: w1_therm fix user buffer overflow and cat
Fixed data reading bug by replacing binary attribute with device one.

Switching the sysfs read from bin_attribute to device_attribute.  The data
is far under PAGE_SIZE so the binary interface isn't required.  As the
device_attribute interface will make one call to w1_therm_read per file
open and buffer, the result is, the following problems go away.

buffer overflow:
	Execute a short read on w1_slave and w1_therm_read_bin would still
	return the full string size worth of data clobbering the user space
	buffer when it returned.  Switching to device_attribute avoids the
	buffer overflow problems.  With the snprintf formatted output dealing
	with short reads without doing a conversion per read would have
	been difficult.
bad behavior:
	`cat w1_slave` would cause two temperature conversions to take place.
	Previously the code assumed W1_SLAVE_DATA_SIZE would be returned with
	each read.  It would not return 0 unless the offset was less
	than W1_SLAVE_DATA_SIZE.  The result was the first read did a
	temperature conversion, filled the buffer and returned, the
	offset in the second read would be less than
	W1_SLAVE_DATA_SIZE and also fill the buffer and return, the
	third read would finnally have a big enough offset to return 0
	and cause cat to stop.  Now w1_therm_read will be called at
	most once per open.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries 07e003417b W1: w1_slave_read_id read bug, use device_attribute
Fix bug reading the id sysfs file.  If less than the full 8 bytes were
read, the next read would start at the first byte instead of continuing.
It needed the offset added to memcpy, or the better solution was to
replace it with the device attribute instead of bin attribute.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:50 -07:00
David Fries 9141f57c7e W1: new module parameter search_count
Added a new module parameter search_count which allows overriding the
default search count.  -1 continual, 0 disabled, N that many times.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries cd7b28d33d W1: recode w1_slave_found logic
Simplified the logic in w1_slave_found by using the new
w1_attach_slave_device function to find a slave and mark it as active or
add the device if the crc checks.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries 9b46741119 W1: be able to manually add and remove slaves
sysfs entries were added to manually add and remove slave devices.  This
is useful if the automatic bus searching is disabled, and the device ids
are already known.

[akpm@linux-foundation.org: fix printk types]
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries 6cd159744e W1: feature, w1_therm.c use strong pullup and documentation
Added strong pullup to thermal sensor driver and general documentation on
the sensor.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries 6a158c0de7 W1: feature, enable hardware strong pullup
Add a strong pullup option to the w1 system.  This supplies extra power
for parasite powered devices.  There is a w1_master_pullup sysfs entry and
enable_pullup module parameter to enable or disable the strong pullup.

The one wire bus requires at a minimum one wire and ground.  The common
wire is used for sending and receiving data as well as supplying power to
devices that are parasite powered of which temperature sensors can be one
example.  The bus must be idle and left high while a temperature
conversion is in progress, in addition the normal pullup resister on
larger networks or even higher temperatures might not supply enough power.
 The pullup resister can't provide too much pullup current, because
devices need to pull the bus down to write a value.  This enables the
strong pullup for supported hardware, which can supply more current when
requested.  Unsupported hardware will just delay with the bus high.

The hardware USB 2490 one wire bus master has a bit on some commands which
will enable the strong pullup as soon as the command finishes executing.
To use strong pullup, call the new w1_next_pullup function to register the
duration.  The next write command will call set_pullup before sending the
data, and reset the duration to zero once it returns.

Switched from simple_strtol to strict_strtol.

Signed-off-by: David Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries 3c52e4e627 W1: w1_process, block or sleep
The w1_process thread's sleeping and termination has been modified.
msleep_interruptible was replaced by schedule_timeout and schedule to
allow for kthread_stop and wake_up_process to interrupt the sleep and the
unbounded sleeping when a bus search is disabled.  The W1_MASTER_NEED_EXIT
and flags variable were removed as they were redundant with
kthread_should_stop and kthread_stop.  If w1_process is sleeping,
requesting a search will immediately wake it up rather than waiting for
the end of msleep_interruptible previously.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries 01e14d6db9 W1: don't delay search start
Move the creation of the w1_process thread to after the device has been
initialized.  This way w1_process doesn't have to check to see if it has
been initialized and the bus search can proceed without sleeping.  That
also eliminates two checks in the w1_process loop.  The sleep now happens
at the end of the loop not the beginning.

Also added a comment for why the atomic_set was 2.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries 0d671b272a W1: abort search early on on exit
Early abort if the master driver or the hardware goes away in the middle
of a bus search operation.  The alternative is to spam the print buffer up
to 64*64 times with read errors in the case of USB.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
David Fries c30c9b1518 W1: fix deadlocks and remove w1_control_thread
w1_control_thread was removed which would wake up every second and process
newly registered family codes and complete some final cleanup for a
removed master.  Those routines were moved to the threads that were
previously requesting those operations.  A new function
w1_reconnect_slaves takes care of reconnecting existing slave devices when
a new family code is registered or removed.  The removal case was missing
and would cause a deadlock waiting for the family code reference count to
decrease, which will now happen.  A problem with registering a family code
was fixed.  A slave device would be unattached if it wasn't yet claimed,
then attached at the end of the list, two unclaimed slaves would cause an
infinite loop.

The struct w1_bus_master.search now takes a pointer to the struct
w1_master device to avoid searching for it, which would have caused a
lock ordering deadlock with the removal of w1_control_thread.

Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:49 -07:00
Jean Delvare 61c91f7ded w1/ds2482: Convert to a new-style driver
The new-style ds2482 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I'm curious if anyone
really needs this though, so it might be removed in the feature.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-07-16 19:30:07 +02:00