Use irq_handler_t for passing clock handler routine around.
And use new rtc_time in place of hwclock_time.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove regs arg from bad interrupt handler.
Use irq_handler_t type for handler arg of local request_irq().
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use irq_handler_t type for passing around timer interrupt routine
in 368360 setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use irq_handler_t type for passing around timer interrupt routine.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kexec: Use EFI_LOADER_DATA for ELF core header
[IA64] permon use-after-free fix
[IA64] sync compat getdents
[IA64] always build arch/ia64/lib/xor.o
[IA64] Remove stack hard limit on ia64
[IA64] point saved_max_pfn to the max_pfn of the entire system
Revert "[IA64] swiotlb abstraction (e.g. for Xen)"
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
sis900 warning fixes
mv643xx_eth: Place explicit port number in mv643xx_eth_platform_data
pcnet32: Fix PCnet32 performance bug on non-coherent architecutres
__devinit & __devexit cleanups for de2104x driver
3c59x: Handle pci_enable_device() failure while resuming
dmfe: Fix link detection
dmfe: fix two bugs
dmfe: trivial/spelling fixes
revert "drivers/net/tulip/dmfe: support basic carrier detection"
ucc_geth: returns NETDEV_TX_BUSY when BD ring is full
ucc_geth: Fix BD processing
natsemi: netpoll fixes
bonding: Improve IGMP join processing
bonding: only receive ARPs for us
bonding: fix double dev_add_pack
Apply commit 0550d9d13e to c-tx39.c too.
And fix a warning in local_tx39_flush_data_cache_page().
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The address where the ELF core header is stored is passed to the secondary
kernel as a kernel command line option. The memory area for this header is
also marked as a separate EFI memory descriptor on ia64.
The separate EFI memory descriptor is at the moment of the type
EFI_UNUSABLE_MEMORY. With such a type the secondary kernel skips over the
entire memory granule (config option, 16M or 64M) when detecting memory.
If we are lucky we will just lose some memory, but if we happen to have
data in the same granule (such as an initramfs image), then this data will
never get mapped and the kernel bombs out when trying to access it.
So this is an attempt to fix this by changing the EFI memory descriptor
type into EFI_LOADER_DATA. This type is the same type used for the kernel
data and for initramfs. In the secondary kernel we then handle the ELF
core header data the same way as we handle the initramfs image.
This patch contains the kernel changes to make this happen. Pretty
straightforward, we reserve the area in reserve_memory(). The address for
the area comes from the kernel command line and the size comes from the
specialized EFI parsing function vmcore_find_descriptor_size().
The kexec-tools-testing code for this can be found here:
http://lists.osdl.org/pipermail/fastboot/2007-February/005983.html
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Perfmon associates vmalloc()ed memory with a file descriptor, and installs
a vma mapping that memory. Unfortunately, the vm_file field is not filled
in, so processes with mappings to that memory do not prevent the file from
being closed and the memory freed. This results in use-after-free bugs and
multiple freeing of pages, etc.
I saw this bug on an Altix on SLES9. Haven't reproduced upstream but it
looks like the same issue is there.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add VERIFY_WRITE check in the beginning like compat_sys_getdents() (EINVAL vs
EFAULT).
Signed-off-by: Alexandr Andreev <aandreev@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Always build ia64 xor.o because multiple config options now depend on it.
Necessary to build .20-mm* on ia64 when, e.g., CONFIG_ASYNC_TX_DMA is
defined. Don't know if '_ASYNC_TX_DMA makes sense on ia64. If not, maybe
Kconfig should preclude it.
Could have defined a Kconfig option that defaults to true if MD_RAID456 ||
ASYNC_TX_DMA to control building of xor.o, but xor.o is only 848 bytes and
this IS ia64...
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make saved_max_pfn point to max_pfn of entire system.
Without this patch is so that vmcore is zero length on ia64. This is
because saved_max_pfn was wrongly being set to the max_pfn of the crash
kernel's address space, rather than the max_pfg on the physical memory of
the machine - the whole purpose of vmcore is to access physical memory that
is not part of the crash kernel's addresss space.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Sort-Of-Acked-By: Jay Lan <jlan@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Comment the fact that sig_info is initialized early in boot, and thus doesn't
need any locking.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a debugging message in the case that mapping a stub fails.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a few formatting bugs in the signal code.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were using the platform_device.id field to identify which ethernet
port is used for mv643xx_eth device. This is not generally correct.
It will be incorrect, for example, if a hardware platform uses a single
port but not the first port. Here, we add an explicit port_number field
to struct mv643xx_eth_platform_data.
This makes the mv643xx_eth_platform_data structure required, but that
isn't an issue since all users currently provide it already.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replaced check_user_space() + __check_access_register with the new
check_space(). The old functions made wrong assumptions about kernel
and user space when the kernel and user address spaces are switched
(kernel in home space, user in primary/secondary space).
Secondly the user process can switch to the accress register mode if
it is running in primary or secondary mode. In addition it can load
an arbitrary value to the access registers. If any other value than
0 for primary space or 1 for secondary space is loaded and memory
is accessed using the base register related to the access register,
the program should be terminated with a SIGSEGV. To achieve that the
DUALD pointer in the DUCT and the PSALD pointer in the PASTE need
to point to an array of 8 invalid access-list entries to get a
ALEN-translation exception if an invalid alet is used.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
nss and kexec don't work together since kexec wants to write to the
read-only text section of the shared kernel image.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reipl doesn't work on older machines were s390_reset_machine() gets
called. The reason is that the text section is read-only but the
variable dump_prefix_page is there. Since s390_reset_machine() writes
to it we get a protection exception.
Therefore move dump_prefix_page to the bss section.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid sprinkling a _lot_ of preempt_disable/preempt_enable pairs.
This would be necessary for e.g. the iucv driver. Also this way we
are more consistent with other architectures which disable
preemption at least for smp_call_function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The illegal operation handler calls the die notifier with DIE_BPT to
let kprobes pick up its breakpoint. If kprobes does not find its
breakpoint it returns NOTIFY_STOP instead of NOTIFY_DONE.
Since we use stop_machine_run on s390 to arm/disarm the kprobes
breakpoints the race that kprobe_handler tries to solve by checking
for the kprobes breakpoints does not exist. Removing the check makes
BUG_ON working again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CONFIG_PARAVIRT broke old glibc bootup: it silently turned off the
selectability of CONFIG_COMPAT_VDSO and thus rendered distro kernels
unbootable on old-style VDSO glibc setups.
the proper solution is to keep COMPAT_VDSO available - if a hypervisor
needs any modification of that concept then we'll judge those changes in
full context, once those changes are submitted.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do not use default=y for CONFIG_VMI (we do not do that for any driver or
special-hardware feature): the overwhelming majority of Linux users does
not need it, and interested users and distributions can enable it
as-needed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clarify the description of the CONFIG_VMI option: describe the reality
that VMI is a VMWare-only interface for now. Once that changes and
another hypervisor adopts the VMI ABI we can change the text.
As can be seen from the Xen paravirtualization patches submitted to lkml
the Xen project has chosen its own, non-VMI interface between Xen and
the para-Linux - so remove Xen from the description.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Temove the mistaken turning on of NO_IDLE_HZ on x86+PARAVIRT kernels.
It's an obsolete, limited form of dynticks.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC arch/i386/kernel/vmi.o
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c: In function 'vmi_map_pt_hook':
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE0' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE1' undeclared (first use in this function)
make[2]: *** [arch/i386/kernel/vmi.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Testing NMI watchdog ... CPU#0: NMI appears to be stuck (54->54)!
CPU#1: NMI appears to be stuck (0->0)!
Keep the PIT/HPET alive when nmi_watchdog = 1 is given on the command
line.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Critical fixes for SMP.
Fix a couple functions which needed to be __devinit and fix a bogus parameter
to AP startup that just so happened to work because the low virtual mapping of
memory was still established.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use para_fill instead of directly setting the APIC ops to the result of the
vmi_get_function call - this allows one to implement a VMI ROM without
implementing APIC functions, just using the native APIC functions.
While doing this, I realized that there is a lot more cleanup that should have
been done. Basically, we should never assume that the ROM implements a
specific set of functions, and always allow fallback to the native
implementation.
This is critical for future compatibility.
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More goo from hrtimers integration. We do compile and run properly with NO_HZ
enabled. There was a period when we didn't because of a missing export, but
that was since fixed.
And with the clocksource code now firmly in place, we can get rid of code that
fixes up the wallclock, since this is done in the common infrastructure. This
actually fixes a timer bug as well, that was caused by do_settimeofday no
longer being callable with interrupts disabled due to the use of
on_each_cpu().
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time_init_hook in paravirt-ops no longer functions in the correct manner
after the integration of the hrtimers code. The problem is that now the call
path for time initialization is:
time_init :
late_time_init = hpet_time_init;
late_time_init -> hpet_time_init:
setup_pit_timer (BAD)
do_time_init --> (via paravirt.h)
time_init_hook --> (via arch_hooks.h)
time_init_hook (in SUBARCH/setup.c)
If this isn't confusing enough, the paravirt case goes through an indirect
function pointer in the paravirt-ops table. The problem is, by the time the
paravirt hook is called, the pit timer is already enabled.
But paravirt guests have their own timer, and don't want to use the PIT.
Rather than intensify the struggle for power going on here, just make it all
nice and simple and just unconditionally do all timer setup in the
late_time_init hook. This also has the advantage of enabling timers in the
same place in all code paths, so everyone has the same bugs and we don't have
outliers who break other code because they turn on timer too early or too
late.
So the paravirt-ops time init function is now by default hpet_time_init, which
is the time init function used for native hardware. Paravirt guests have the
chance to override this when they setup the paravirt-ops table, and should
need no change.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not respecting udelay causes problems with any virtual hardware that is passed
through to real hardware. This can be noticed by any device that interacts
with the real world in real time - like AP startup, which takes real time. Or
keyboard LEDs, which should blink in real-time. Or floppy drives, but only
when passed through to a real floppy controller on OSes which can't
sufficiently buffer the floppy commands to emulate a zero latency floppy. Or
IDE drives, when connecting to a physical CDROM.
This was mostly a hack to get the kernel to boot faster, but it introduced a
number of misvirtualization bugs, and Alan and Pavel argued pretty strongly
against it. We were the only client, and now want to clean up this cruft.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide a PT map hook for HIGHPTE kernels to designate where they are mapping
page tables. This information is required so the physical address of PTE
updates can be determined; otherwise, the mm layer would have to carry the
physical address all the way to each PTE modification callsite, which is even
more hideous that the macros required to provide the proper hooks.
So lets not mess up arch neutral code to achieve this, but keep the horror in
an #ifdef HIGHPTE in include/asm-i386/pgtable.h. I had to use macros here
because some types are not yet defined in all the include paths for this
header.
This patch is absolutely required for HIGHPTE kernels to operate properly with
VMI.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to share the common code in tsc.c which does CPU Khz calibration, we
need to make an accurate value of CPU speed available to the tsc.c code. This
value loses a lot of precision in a VM because of the timing differences with
real hardware, but we need it to be as precise as possible so the guest can
make accurate time calculations with the cycle counters.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The custom_sched_clock hook is broken. The result from sched_clock needs to
be in nanoseconds, not in CPU cycles. The TSC is insufficient for this
purpose, because TSC is poorly defined in a virtual environment, and mostly
represents real world time instead of scheduled process time (which can be
interrupted without notice when a virtual machine is descheduled).
To make the scheduler consistent, we must expose a different nature of time,
that is scheduled time. So deprecate this custom_sched_clock hack and turn it
into a paravirt-op, as it should have been all along. This allows the tsc.c
code which converts cycles to nanoseconds to be shared by all paravirt-ops
backends.
It is unfortunate to add a new paravirt-op, but this is a very distinct
abstraction which is clearly different for all virtual machine
implementations, and it gets rid of an ugly indirect function which I
ashamedly admit I hacked in to try to get this to work earlier, and then even
got in the wrong units.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Critical bugfixes for the VMI-Timer code.
1) Do not setup a one shot alarm if we are keeping the periodic alarm
armed. Additionally, since the periodic alarm can be run at a lower rate
than HZ, let's fixup the guard to the no-idle-hz mode appropriately. This
fixes the bug where the no-idle-hz mode might have a higher interrupt rate
than the non-idle case.
2) The interrupt handler can no longer adjust xtime due to nested lock
acquisition. Drop this. We don't need to check for wallclock time at
every tick, it can be done in userspace instead.
3) Add a bypass to disable noidle operation. This is useful as a last
minute workaround, or testing measure.
4) The code to skip the IO_APIC timer testing (no_timer_check) should be
conditional on IO_APIC, not SMP, since UP kernels can have this configured
in as well.
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't have any use for these machvec fixups anymore, kill them all
off and go with the generic instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables the SM501 drivers for the R2D board. Additional
work needs to be done to migrate off of the VoyagerGX cchip
code to make use of the rest of the mfd infrastructure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I run a preemptive kernel-2.6.20 for SH7780, a created
kthread(pdflush) can not exit by do_exit() in kernel_thread_helper. I
think that the created kthread should have a room for 'struct pt_regs'
space on the stack top, because __switch_to() will refer to the space as
follows using 'regs = task_pt_regs(prev)' and next condition may be true.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a missing return in do_signal() that caused the saved
sigmask to be written back after having successfully delivered
the signal.
Signed-off-by: Ryusuke Sakato <sakato@hsdv.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This takes care of tearing down the UBC so it's not inadvertently
left configured at the next context switch time. Failure to do
this results in spurious SIGTRAPs in certain debug sequences.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] Acorn: move the i2c bus driver into drivers/i2c
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
[ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
[ARM] rtc-pcf8583: correct month and year offsets
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
[ARM] EBSA110: Work around build errors
[ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
[ARM] 4239/1: S3C24XX: Update kconfig entries for PM
[ARM] 4238/1: S3C24XX: docs: update suspend and resume
[ARM] 4237/2: oprofile: Always allow backtraces on ARM
[ARM] Yet more asm/apm-emulation.h stuff
ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
ARM: OMAP: Use linux/delay.h not asm/delay.h
ARM: OMAP: Remove obsolete alsa typedefs
ARM: OMAP: omap1510->15xx conversions needed for sx1
ARM: OMAP: Add missing includes to board-nokia770
ARM: OMAP: Workqueue changes for board-h4.c
ARM: OMAP: dmtimer.c omap1 register fix
ARM: OMAP: board-nokia770: correct lcd name
...
Adds cardbus ressources for MTX1 boards which have a PCMCIA controller.
Signed-off-by: Florian Fainelli <florian.fainelli@int-evry.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has removed unused timer resource.
Moreover, the name of reserved resources ware changed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If R4k counter was used for hpt_timer and interrupt source,
c0_hpt_timer_init() initializes the c0_compare register.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick). This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to stop tc35815 before resetting the board. This fixes the
build of tc35815 as a module. This also means there is no caller of
tc35815_killall left, so remove that function also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We mistakedly modify 'bus' in the innermost loop. What
should happen is that at each register index iteration,
we start with the same 'bus'.
So preserve it's value at the top level, and use a loop
local variable 'dbus' for iteration.
This bug causes registers other than the first to be
decoded improperly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update help text with location of documentation
and duplicate the note on the speed of CRC
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always allow backtrace when using oprofile on ARM, even if a PMU
isn't present.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert 1510->15xx in generic omap code, so that sx1 can work.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing includes to board-nokia770 to make it
compile again.
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When I went to use dmtimer7 it did not seem to work. I noticed that
the base addresses for dmtimers 7 and 8 were set wrong. A simple patch
to correct a small error. Confirmed to fix the problem on an OSK.
Signed-off-by: Matthew Percival <matthew@capgo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some time ago, the 'lcd_lph8923' device was renamed to 'lcd_mipid' but
the board-nokia770.c file was not updated accordingly, leading to not
working lcd.
This one-liner fixe the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Teach OMAP2 gp timer that HZ isn't always 100.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:765: warning: ignoring return value
of 'subsys_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap2/timer-gp.c: In function
'omap2_gp_timer_init':
arch/arm/mach-omap2/timer-gp.c:70: warning: implicit
declaration of function 'setup_irq'
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warnings
arch/arm/plat-omap/dmtimer.c: In function
'omap_dm_timer_modify_idlect_mask':
arch/arm/plat-omap/dmtimer.c:317: warning: no return
statement in function returning non-void
arch/arm/plat-omap/mailbox.c: In function 'omap_mbox_init':
arch/arm/plat-omap/mailbox.c:231: warning: ignoring return
value of 'class_device_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No IRQF_TRIGGER set_type function for IRQ 353 (MPUIO)
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes serial usable also on omap310, not only 1510.
(changing 1510->15xx)
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register bits are reset by writing one. Remove the unneeded reads and
fix writes to not clear too many bits.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning:
arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):
arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Greg Ungerer
Linus Torvalds
Ralf Baechle
Atsushi Nemoto
Yoichi Yuasa
Magnus Damm
Nick Piggin
Alexandr Andreev
Lee Schermerhorn
Horms
Jeff Dike
Adrian Bunk
Thomas Gleixner
Dale Farnsworth
Gerald Schaefer
Heiko Carstens
Martin Schwidefsky
Ingo Molnar
john stultz
David Rientjes
Zachary Amsden
David Brownell
Eric W. Biederman
Paul Mundt
Hideo Saito
Ryusuke Sakato
Stuart Menefy
Florian Fainelli
Russell King
David S. Miller
Ben Dooks
Richard Purdie
Tony Lindgren
Vladimir Ananiev
Dirk Behme
Matthew Percival
Arnaud Patard
David Brownell
Marek Vašut
Timo Teras
Andrzej Zaborowski