Enhance EDID and mode table handling
* Adds support for lower-end DL chips on higher-end monitors
* Adds support for using fbdev standard EDID parsing and handling
* Adds support for more dynamic reallocation of framebuffer, based on new EDID
Queries EDID from hardware with several retries then
queries DisplayLink chip for max pixel area via vendor descriptor.
Uses existing fbdev mode handling service funcations to build mode list
of common modes between adapter and monitor.
This enables lower-end chips (e.g. DL-125) to successfully pick a compatible
mode on higher end monitors (e.g. whose default mode is over 1280x1024).
Reallocate framebuffer if necessary in response to new max mode.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revamp reference handling and synchronization for unload/shutdown
Udlfb is a "virtual" framebuffer device that really exists on
two separate stacks: at the bottom of the framebuffer interface,
and on top of USB. During unload, there's no guarantee which
one will tear down first. So reference counting must be solid
to handle all possibilities and not access anything once its gone.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove metrics_misc sysfs attribute
Previously returned multiple values, which goes against sysfs guidelines.
Had been used for debugging to figure out which of the multiple
fbdev interfaces an app was using, but log file messages are sufficient.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ability to power off monitor with standard blanking interface
Used by X servers and others to manage power of dislpay
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore fbdev character read and write support
Enables access to the framebuffer from simple reads and writes
to /dev/fb0 (or fb1, ...). Low performance, because of extra copy
and because udlfb must scan every pixel for changes. But very
useful for testing and simple image display, etc.
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We must reduce our own mtu when we reduce the mtu of any device we use
to transfer our packets. Otherwise we may accept to large packets which
gets dropped by the actual device.
Reported-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Information about dropped packets are usually only interesting for
debugging purposes and otherwise open the possibility to flood the logs
of the target machine with useless information.
pr_debug will not output those information on a nodebug kernel.
Reported-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
batman_if has the name of the net_dev as extra string in its own
structure, but also holds a reference to the actual net_device structure
which always has the current name of the device. This makes it
unneccessary and also more complex because we must update the name in
situations when we receive a NETDEV_CHANGENAME event.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes all remaining global variables and includes the
necessary bits into the bat_priv structure. It is the last
remaining piece to allow multiple concurrent mesh clouds on the
same device.
A few global variables have been rendered obsolete during the process
and have been removed entirely.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces the static bat0 interface with a dynamic/abstracted
approach. It is now possible to create multiple batX interfaces by
assigning hard interfaces to them. Each batX interface acts as an
independent mesh network. A soft interface is removed once no hard
interface references it any longer.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We must ensure that all interesting data is linear and not paged out to
access all information in a header or a full batman-adv related packet.
Otherwise we may drop packets which have non-linear headers but which
hold valid data.
This doesn't affect non-linear skbs which have all headers in a linear
head unless we must process the whole packet like in ogms or vis
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can use skb_cow instead of a handwritten function to test and create
a writable skb buffer. This also allows us to pre-allocate headroom to
be able to send the data without re-allocating the buffer again to add
the ethernet header.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vis information structure is used in a way that it can be transfered
directly as packet. It still had to be copied into a skb because of an
extra buffer used for the actual preparation of the data. This is
unnecessary and can be replaced by a simple clone instead of an full
copy before each send.
This makes also the send_raw_packet function obsolete.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All originator messages are send through aggregation buffers. Those
buffers can directly be allocated as skb to reduce the cost of
allocation an extra buffer and copying them to a new allocated skb
directly before it gets send.
Now only the skb must be cloned in case of send_packet_to_if as it gets
called by send_packet for each interface. Non-primary ogms must not
cloned at all because they will only send once and the forward_packet
structure is freed by send_outstanding_bat_packet afterwards.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
batman-adv tries to resend broadcasts on all interfaces up to three
times. For each round and each interface it must provide a skb which
gets consumed by the sending function.
It is unnecessary to copy the data of each broadcast because the actual
data is either not shared or already copied by add_bcast_packet_to_list.
So it is enough to just copy the skb control data
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
my_skb_push provided an easy way to allocate enough headroom in
situation were we don't have enough space left and move the data pointer
to the new position, but we didn't checked wether we are allowed to
write to the new pushed header. This is for example a problem when the
skb was cloned and thus doesn't have a private data part.
my_skb_head_push now replaces my_skb_push by using skb_cow_head to
provide only a large enough, writable header without testing for the
rest of the (maybe shared) data. It will also move the data pointer
using skb_push when skb_cow_head doesn't fail.
This should give us enough flexibility in situation were skbs will be
queued by underlying layers and still doesn't unnecessarily copy the
data in situations when the skb was consumed right away during
dev_queue_xmit.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Batman-adv globally registered the batman-adv packet type and installed
a hook to batman_skb_recv(). Each interface receiving a packet with that
type would end up in this function which then had to loop through all
batman-adv internal interface structures to find the its meta data. The
more interfaces a system had the longer the loops might take. Each and
every packet goes through this function making it a performance critical
loop.
This patch installs the hook for each activated interface. The called
batman_skb_recv() can distinguish these calls, therefore avoiding the
loop through the interface structures.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is unnecessary to generate an icmp packet in an extra memory region
and than copying it to a new allocated skb.
This also resolved the problem that we do inform the user that we
couldn't send the packet because we couldn't allocate the socket buffer.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a simple layer2 fragmentation to allow traffic
exchange over network interfaces with a MTU smaller than 1500 bytes. The
fragmentation splits the big packets into two parts and marks the frames
accordingly. The receiving end buffers the packets to reassemble the
orignal packet before passing it to the higher layers. This feature
makes it necessary to modify the batman-adv encapsulation for unicast
packets by adding a sequence number, flags and the originator address.
This modifcation is part of a seperate packet type for fragemented
packets to keep the original overhead as low as possible. This patch
enables the feature by default to ensure the data traffic can travel
through the network. But it also prints a warning to notify the user
about the performance implications.
Note: Fragmentation should be avoided at all costs since it has a
dramatic impact on the performance, especially when it comes wifi
networks. Instead of a single packet, 2 packets have to be sent! Not
only valuable airtime is wasted but also packetloss decreases the
throughput. A link with 50% packetloss and fragmentation enabled is
pretty much unusable.
Signed-off-by: Andreas Langer <an.langer@gmx.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
to support multiple mesh devices later, we need to move global variables
like the queues into corresponding private structs bat_priv of the soft
devices.
Note that this patch still has a lot of FIXMEs and depends on the global
soft_device variable. This should be resolved later, e.g. by referencing
the parent soft device in batman_if.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Kernighan algorithm is not able to calculate the number of set bits
in parallel and the compiler cannot replace it with optimized
instructions.
The kernel provides specialised functions for each cpu which can either
use a software implementation or hardware instruction depending on the
target cpu.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Ethernet header is counted when transmitting a packet, so it should also
be counted when receiving a packet. With this patch, the rx_bytes and tx_bytes
statistics behave like an ordinary Ethernet interface.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Version 2010.1.0 of the extra kernel module was released and thus the
documentation should be updated and everything prepared for the the
upcoming patchset.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The changelog is only generated on standalone releases. Thus it has no
real value for the in-kernel version of batman-adv.
Reported-by: Abraham Arce <abraham.arce.moreno@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 96d592ed59.
The netfilter hook seems to be misused and may leak skbs in situations
when NF_HOOK returns NF_STOLEN. It may not filter everything as
expected. Also the ethernet bridge tables are not yet capable to
understand batman-adv packet correctly.
It was only added for testing purposes and can be removed again.
Reported-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_util.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_init.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_setmode.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_ext.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes a duplicate include directive in
drivers/staging/rtl8187se/ieee80211/ieee80211.h.
Signed-off-by: Andre Nogueira <andre.neo.net@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In wmi_bssInfo_event_rx, there is unneeded check for bss, because it
is in the branch where the bss is checked to be non-null already.
Remove the superfluous check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Vipin Mehta <vmehta@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[2nd version -- melded all three together]
1) There is a missing return or goto statement in one fail path in
sasem_probe, so that the code contiues its normal execution (and
unlocks a mutex twice). Fix that by jumping to the right place.
Anyway the code is very broken on its fail paths and there are many
leaks. But that's a different story.
2) There is an omitted unlock in one fail path in vfd_write, jump to
the right place to unlock the lock.
3) In the probe function, there is one more error where the lock is
not unlocked. Fix that by jumping to the proper place.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When 'context' allocation fails in imon_probe, we jump to unlock
context->ctx_lock. This is wrong as context is NULL and the lock is
not locked.
Fix the labels.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I don't know how gcc interprets this, but it wouldn't surprise me if it
choose something different than start-of-comment
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've no idea where this came from!
Also fixed form -> from in comment
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bernie Thompson
Joe Perches
Javier Martinez Canillas
Sven Eckelmann
Marek Lindner
Andreas Langer
Simon Wunderlich
Prashant P. Shah
Andre Nogueira
Andrea Gelmini
Jiri Slaby
Uwe Kleine-König
Jonathan Cameron