Commit Graph

9320 Commits

Author SHA1 Message Date
Martin K. Petersen 5db44863b6 [SCSI] sd: Implement support for WRITE SAME
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.

 - We set the default maximum to 0xFFFF because there are several
   devices out there that only support two-byte block counts even with
   WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
   device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
   LIMITS VPD.

 - max_write_same_blocks can be overriden per-device basis in sysfs.

 - The UNMAP discovery heuristics remain unchanged but the discard
   limits are tweaked to match the "real" WRITE SAME commands.

 - In the error handling logic we now distinguish between WRITE SAME
   with and without UNMAP set.

The discovery process heuristics are:

 - If the device reports a SCSI level of SPC-3 or greater we'll issue
   READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
   supported. If that's the case we will use it.

 - If the device supports the block limits VPD and reports a MAXIMUM
   WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).

 - Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
   0xFFFFFFFF or the block count exceeds 0xFFFF.

 - no_write_same is set for ATA, FireWire and USB.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 22:45:42 -08:00
Martin K. Petersen 26e85fcd15 [SCSI] sd: Permit merged discard requests
Support requests with more than one bio payload for discards. The total
number of bytes to be discarded is stored in req->__data_len and used in
sd_done() to complete the I/O.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 21:23:53 -08:00
Martin K. Petersen 3c6bdaeab4 [SCSI] Add a report opcode helper
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.

We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 21:11:31 -08:00
Maciej Patelczyk 49bd665c54 [SCSI] isci: copy fis 0x34 response into proper buffer
SATA MICROCODE DOWNALOAD fails on isci driver. After receiving Register
Device to Host (FIS 0x34) frame Initiator resets phy.
In the frame handler routine response (FIS 0x34) was copied into wrong
buffer and upper layer did not receive any answer which resulted in
timeout and reset.
This patch corrects this bug.

Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 13:45:14 +00:00
Linus Torvalds 2b1768f39a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller:
 "Several build/bug fixes for sparc, including:

  1) Configuring a mix of static vs.  modular sparc64 crypto modules
     didn't work, remove an ill-conceived attempt to only have to build
     the device match table for these drivers once to fix the problem.

     Reported by Meelis Roos.

  2) Make the montgomery multiple/square and mpmul instructions actually
     usable in 32-bit tasks.  Essentially this involves providing 32-bit
     userspace with a way to use a 64-bit stack when it needs to.

  3) Our sparc64 atomic backoffs don't yield cpu strands properly on
     Niagara chips.  Use pause instruction when available to achieve
     this, otherwise use a benign instruction we know blocks the strand
     for some time.

  4) Wire up kcmp

  5) Fix the build of various drivers by removing the unnecessary
     blocking of OF_GPIO when SPARC.

  6) Fix unintended regression wherein of_address_to_resource stopped
     being provided.  Fix from Andreas Larsson.

  7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
     Larsson."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
  sparc: Support atomic64_dec_if_positive properly.
  of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
  sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
  sparc: Add sparc support for platform_get_irq()
  sparc: Allow OF_GPIO on sparc.
  qlogicpti: Fix build warning.
  sparc: Wire up sys_kcmp.
  sparc64: Improvde documentation and readability of atomic backoff code.
  sparc64: Use pause instruction when available.
  sparc64: Fix cpu strand yielding.
  sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.
2012-11-10 21:58:34 +01:00
David S. Miller f7e8d9f830 qlogicpti: Fix build warning.
The build warns:

drivers/scsi/qlogicpti.c: In function 'qpti_sbus_probe':
drivers/scsi/qlogicpti.c:1316:45: warning: passing argument 1 of 'scsi_host_alloc' discards 'const' qualifier from pointer target type [enabled by default]
include/scsi/scsi_host.h:778:26: note: expected 'struct scsi_host_template *' but argument is of type 'const struct scsi_host_template *'

The problem is that of_device_id->data is a const void pointer.

This is pretty silly in this specific instance, because for all
matched device IDs we set match->data to the same value,
&qpti_template.

So just use that directly instead of the unnecessary and improperly
typed abstraction.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-28 13:26:37 -07:00
Roland Dreier c8292d1da5 qla2xxx: Update target lookup session tables when a target session changes
It is possible for the target code to change the loop_id or s_id of a
target session in reaction to an FC fabric change.  However, the
session structures are stored in tables that are indexed by these two
keys, and if we just change the session structure but leave the
pointers to it in the old places in the table, havoc can ensue.  For
example, a new session might come along that should go in the old slot
in the table and overwrite the old session pointer.

To handle this, add a new tgt_ops->update_sess() method that also
updates the "by loop_id" and "by s_id" lookup tables when a session
changes, so that the keys where a session pointer is stored in these
tables always matches the keys in the session structure itself.

(nab: Drop unnecessary double inversion with FCF_CONF_COMP_SUPPORTED
      usage)

Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-10-26 12:29:46 -07:00
Roland Dreier c046aa0f0f tcm_qla2xxx: Format VPD page 83h SCSI name string according to SPC
My draft of SPC-4 says the following about the SCSI name string in
inquiry VPD page 83h:

    The SCSI NAME STRING field starts with either:

    a) the four UTF-8 characters 'eui.' concatenated with 16, 24, or
       32 hexadecimal digits (i.e., the UTF-8 characters 0 through 9
       and A through F) for an EUI-64 based identifier (see
       7.8.6.5). The first hexadecimal digit shall be the most
       significant four bits of the first byte (i.e., most significant
       byte) of the EUI-64 based identifier;
    b) the four UTF-8 characters 'naa.' concatenated with 16 or 32
       hexadecimal digits for an NAA identifier (see 7.8.6.6). The
       first hexadecimal digit shall be the most significant four bits
       of the first byte (i.e., most significant byte) of the NAA
       identifier; or
    c) the four UTF-8 characters 'iqn.' concatenated with an iSCSI
       Name for an iSCSI-name based identifier (see iSCSI).

However, the .tpg_get_wwn method for tcm_qla2xxx formats the WWN so
the SCSI name string looks like "52:4a:93:7d:24:5f:b2:12,t,0x0001".
This patch corrects the code so that VPD 83h gives a SPC-compliant
SCSI name string like "naa.524a937d245fb212,t,0x0001" while leavig
other uses alone (so configfs will still work with ':' separated WWNs).

Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-10-26 12:29:46 -07:00
Nicholas Bellinger 29c08cdabd qla2xxx: Add missing ->vport_slock while calling qlt_update_vp_map
All other callers of qlt_update_vp_map() already hold ->vport_slock
while updating the vp target map, so go ahead and add the missing
->vport_slock within qla24xx_disable_vp() code.

Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roland Dreier <roland@purestorage.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-10-26 12:29:46 -07:00
Olof Johansson 068a565afa Merge branch 'testing/driver-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into fixes
A collection of warning fixes on non-ARM code from Arnd Bergmann:

* 'testing/driver-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: s3c: mark s3c2440_clk_add as __init_refok
  spi/s3c64xx: use correct dma_transfer_direction type
  pcmcia: sharpsl: don't discard sharpsl_pcmcia_ops
  USB: EHCI: mark ehci_orion_conf_mbus_windows __devinit
  mm/slob: use min_t() to compare ARCH_SLAB_MINALIGN
  SCSI: ARM: make fas216_dumpinfo function conditional
  SCSI: ARM: ncr5380/oak uses no interrupts
2012-10-19 15:40:18 -07:00
Linus Torvalds 6a5a3d6a4a SCSI misc on 20121012
This is an assorted set of stragglers into the merge window with driver
 updates for megaraid_sas, lpfc, bfi and mvumi. It also includes some fairly
 major fixes for virtio-scsi (scatterlist init), scsi_debug (off by one error),
 storvsc (use after free) and qla2xxx (potential deadlock).
 
 Signed-off-by: James Bottomley <JBottomley@Parallels.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQEcBAABAgAGBQJQeJfDAAoJEDeqqVYsXL0MhqgH/Rq7ebKJvKcUoKsTJKsZ2H0V
 iaK5wBvhPBXLxYF5fMEnOwOPT34ry4SWJ7IqTKQqZItx1kqZuG4OTUjmueUCxaMb
 7ELFWqyV1z7lyt+XAvNt/RTdMFl3n2SkOxgQJ8kzTPYzEHcE8GCH+dtuqzxoOUqx
 styM6DE9Y5cQR1ozacj/QDMv4gn2jclclYgaxR2OTqzqQFeTMzn5KfRH4b6vYtos
 ZuYlFE4uaAQhsUGeOqTcGlMvot4tyz4KGO4oy4xkHRQXRVQ52Ve8slRr1z4EUJ3H
 rOpz869Y97vnSDFyXuJDa8PpbDd5KOU1uJBxE/3LlCoXIQj4u71hDXETRtq8jtg=
 =T50d
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull misc SCSI updates from James Bottomley:
 "This is an assorted set of stragglers into the merge window with
  driver updates for megaraid_sas, lpfc, bfi and mvumi.  It also
  includes some fairly major fixes for virtio-scsi (scatterlist init),
  scsi_debug (off by one error), storvsc (use after free) and qla2xxx
  (potential deadlock).

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
  [SCSI] storvsc: Account for in-transit packets in the RESET path
  [SCSI] qla2xxx: fix potential deadlock on ha->hardware_lock
  [SCSI] scsi_debug: Fix off-by-one bug when unmapping region
  [SCSI] Shorten the path length of scsi_cmd_to_driver()
  [SCSI] virtio-scsi: support online resizing of disks
  [SCSI] virtio-scsi: fix LUNs greater than 255
  [SCSI] virtio-scsi: initialize scatterlist structure
  [SCSI] megaraid_sas: Version, Changelog, Copyright update
  [SCSI] megaraid_sas: Remove duplicate code
  [SCSI] megaraid_sas: Add SystemPD FastPath support
  [SCSI] megaraid_sas: Add array boundary check for SystemPD
  [SCSI] megaraid_sas: Load io_request DataLength in bytes
  [SCSI] megaraid_sas: Add module param for configurable MSI-X vector count
  [SCSI] megaraid_sas: Remove un-needed completion_lock spinlock calls
  [SCSI] lpfc 8.3.35: Update lpfc version for 8.3.35 driver release
  [SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on
  [SCSI] lpfc 8.3.35: Fix error with fabric service parameters causing performance issues
  [SCSI] lpfc 8.3.35: Fixed SCSI host create showing wrong link speed on SLI3 HBA ports
  [SCSI] lpfc 8.3.35: Fixed not checking solicition in progress bit when verifying FCF record for use
  [SCSI] lpfc 8.3.35: Fixed messages for misconfigured port errors
  ...
2012-10-13 10:57:01 +09:00
Linus Torvalds a188e7e93a Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull scsi target updates from Nicholas Bellinger:
 "Things have been calm for the most part with no new fabric drivers in
  flight for v3.7 (we're up to eight now !), so this update is primarily
  focused on addressing a few long-standing items within target-core and
  iscsi-target fabric code.

  The highlights include:

   - target: Simplify fabric sense data length handling (roland)
   - qla2xxx: Fix endianness of task management response code (roland)
   - target: fix truncation of mode data, support zero allocation length
     (paolo)
   - target: Properly support zero-length commands in normal processing
     path (paolo)
   - iscsi-target: Correctly set 0xffffffff field within ISCSI_OP_REJECT
     PDU (ronnie + nab)
   - iscsi-target: Add explicit set of cache_dynamic_acls=1 for TPG
     demo-mode (ronnie + nab)
   - target/file: Re-enable optional fd_buffered_io=1 operation (nab +
     hch)
   - iscsi-target: Add MaxXmitDataSegmenthLength forr target ->
     initiator MDRSL declaration (nab)
   - target: Add target_submit_cmd_map_sgls for SGL fabric memory
     passthrough (nab + hch)
   - tcm_loop: Convert I/O path to use target_submit_cmd_map_sgls (hch +
     nab)
   - tcm_vhost: Convert I/O path to use target_submit_cmd_map_sgls (nab
     + hch)

  The last series for adding a new target_submit_cmd_map_sgls() fabric
  caller (as requested by hch) that accepts pre-allocated SGL memory
  (using existing logic), along with converting tcm_loop + tcm_vhost has
  only been in -next for the last days, but has gotten enough review
  +testing and is clear enough a mechanical change that I think it's
  reasonable to merge for -rc1 code.

  Thanks again to everyone who contributed this round! Extra special
  thanks to Roland (PureStorage) for tracking down the qla2xxx target
  TMR response code endian issue, and to Paolo (Redhat) for resolving
  the long standing zero-length CDB issues within target-core between
  virtual and pSCSI backends."

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
  iscsi-target: Bump defaults for nopin_timeout + nopin_response_timeout values
  iscsit: proper endianess conversions
  iscsit: use the itt_t abstract type
  iscsit: add missing endianess conversion in iscsit_check_inaddr_any
  iscsit: remove incorrect unlock in iscsit_build_sendtargets_resp
  iscsit: mark various functions static
  target/iscsi: precedence bug in iscsit_set_dataout_sequence_values()
  target/usb-gadget: strlen() doesn't count the terminator
  target/usb-gadget: remove duplicate initialization
  tcm_vhost: Convert I/O path to use target_submit_cmd_map_sgls
  target: Add control CDB READ payload zero work-around
  tcm_loop: Convert I/O path to use target_submit_cmd_map_sgls
  target: Add target_submit_cmd_map_sgls for SGL fabric memory passthrough
  iscsi-target: Add explicit set of cache_dynamic_acls=1 for TPG demo-mode
  iscsi-target: Change iscsi_target_seq_pdu_list.c to honor MaxXmitDataSegmentLength
  iscsi-target: Add MaxXmitDataSegmentLength connection recovery check
  iscsi-target: Convert incoming PDU payload checks to MaxXmitDataSegmentLength
  iscsi-target: Enable MaxXmitDataSegmentLength operation in login path
  iscsi-target: Add base MaxXmitDataSegmentLength code
  target/file: Re-enable optional fd_buffered_io=1 operation
  ...
2012-10-10 19:52:19 +09:00
Arnd Bergmann 4896817731 SCSI: ARM: make fas216_dumpinfo function conditional
The fas216_dumpinfo function is only used by __fas216_checkmagic,
which is conditionally compiled, so we should put both functions
inside of the same #ifdef.

Without this patch, building rpc_defconfig results in:

drivers/scsi/arm/fas216.c:182:13: warning: 'fas216_dumpinfo' defined but not used [-Wunused-function]

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-scsi@vger.kernel.org
2012-10-09 21:56:26 +02:00
Arnd Bergmann ea065f13cc SCSI: ARM: ncr5380/oak uses no interrupts
The ncr5380 driver is included by multiple board specific
drivers, which may or may not use the interrupt handler.
The oak variant doesn't, and should set the DONT_USE_INTR
macro.

Without this patch, building rpc_defconfig results in:

drivers/scsi/arm/../NCR5380.c:1160:20: warning: 'oakscsi_intr' defined but not used [-Wunused-function]

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-scsi@vger.kernel.org
2012-10-09 21:56:24 +02:00
K. Y. Srinivasan 5c1b10ab7f [SCSI] storvsc: Account for in-transit packets in the RESET path
Properly account for I/O in transit before returning from the RESET call.
In the absense of this patch, we could have a situation where the host may
respond to a command that was issued prior to the issuance of the RESET
command at some arbitrary time after responding to the RESET command.
Currently, the host does not do anything with the RESET command.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 12:28:58 +01:00
Jiri Kosina f24b5cb818 [SCSI] qla2xxx: fix potential deadlock on ha->hardware_lock
Lockdep reports:

=== [ cut here ] ===
 =========================================================
 [ INFO: possible irq lock inversion dependency detected ]
 3.6.0-0.0.0.28.36b5ec9-default #1 Not tainted
 ---------------------------------------------------------
 qla2xxx_1_dpc/368 just changed the state of lock:
  (&(&ha->vport_slock)->rlock){+.....}, at: [<ffffffffa009b377>] qla2x00_configure_hba+0x197/0x3c0 [qla2xxx]
 but this lock was taken by another, HARDIRQ-safe lock in the past:
  (&(&ha->hardware_lock)->rlock){-.....}

and interrupts could create inverse lock ordering between them.

other info that might help us debug this:
 Possible interrupt unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&(&ha->vport_slock)->rlock);
                               local_irq_disable();
                               lock(&(&ha->hardware_lock)->rlock);
                               lock(&(&ha->vport_slock)->rlock);
  <Interrupt>
    lock(&(&ha->hardware_lock)->rlock);
=== [ cut here ] ===

Fix the potential deadlock by disabling IRQs while holding ha->vport_slock.

Reported-and-tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 12:27:25 +01:00
Lukas Czerner bc977749e9 [SCSI] scsi_debug: Fix off-by-one bug when unmapping region
Currently it is possible to unmap one more block than user requested to
due to the off-by-one error in unmap_region(). This is probably due to
the fact that the end variable despite its name actually points to the
last block to unmap + 1. However in the condition it is handled as the
last block of the region to unmap.

The bug was not previously spotted probably due to the fact that the
region was not zeroed, which has changed with commit
be1dd78de5. With that commit we were able
to corrupt the ext4 file system on 256M scsi_debug device with LBPRZ
enabled using fstrim.

Since the 'end' semantic is the same in several functions there this
commit just fixes the condition to use the 'end' variable correctly in
that context.

Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 12:23:11 +01:00
Li Zhong 329a402cb0 [SCSI] Shorten the path length of scsi_cmd_to_driver()
This patch tries to shorten the path length of scsi_cmd_to_driver(). As only
REQ_TYPE_BLOCK_PC commands can be submitted without a driver, so we could
avoid the related NULL checking, as long as we make sure we don't use it for
REQ_TYPE_BLOCK_PC type commands. Plus, this fixes a bug where you get
different behaviors from REQ_TYPE_BLOCK_PC commands when a driver is and isn't
attached.

Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 12:04:42 +01:00
Paolo Bonzini 865b58c05b [SCSI] virtio-scsi: support online resizing of disks
Support the LUN parameter change event.  Currently, the host fires this event
when the capacity of a disk is changed from the virtual machine monitor.
The resize then appears in the kernel log like this:

  sd 0:0:0:0: [sda] 46137344 512-byte logical blocks: (23.6 GB/22.0 GIb)
  sda: detected capacity change from 22548578304 to 23622320128

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:24:47 +01:00
Paolo Bonzini 9da5f5ac6a [SCSI] virtio-scsi: fix LUNs greater than 255
virtio-scsi needs to report LUNs greater than 256 using the "flat"
format.  Because the Linux SCSI layer just maps the SCSI LUN to
an u32, without any parsing, these end up in the range from 16640
to 32767.  Fix max_lun to account for the possibility that logical
unit numbers are encoded with the "flat" format.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:23:28 +01:00
Richard W.M. Jones 2e9c9dfde0 [SCSI] virtio-scsi: initialize scatterlist structure
The sg struct is used without being initialized, which breaks
when CONFIG_DEBUG_SG is enabled.

Cc: stable@vger.kernel.org
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:22:45 +01:00
adam radford ae59057b64 [SCSI] megaraid_sas: Version, Changelog, Copyright update
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:21:48 +01:00
adam radford a3a922099c [SCSI] megaraid_sas: Remove duplicate code
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:20:41 +01:00
adam radford 8ead581609 [SCSI] megaraid_sas: Add SystemPD FastPath support
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:19:48 +01:00
adam radford e187df6399 [SCSI] megaraid_sas: Add array boundary check for SystemPD
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:19:11 +01:00
adam radford f9eff81584 [SCSI] megaraid_sas: Load io_request DataLength in bytes
Load io_request->DataLength in bytes for newer firmware that supports high
availability.

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:17:26 +01:00
adam radford 079eaddf2e [SCSI] megaraid_sas: Add module param for configurable MSI-X vector count
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:12:30 +01:00
adam radford 58af7b884f [SCSI] megaraid_sas: Remove un-needed completion_lock spinlock calls
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-09 11:04:08 +01:00
Konstantin Khlebnikov 314e51b985 mm: kill vma flag VM_RESERVED and mm->reserved_vm counter
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:

 | effect                 | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump      | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock           | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP

This patch removes reserved_vm counter from mm_struct.  Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.

Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.

remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.

[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-10-09 16:22:19 +09:00
James Smart 1d4329f8ec [SCSI] lpfc 8.3.35: Update lpfc version for 8.3.35 driver release
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:16:11 +01:00
James Smart 8b68cd5258 [SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:14:41 +01:00
James Smart 2eb6862aaf [SCSI] lpfc 8.3.35: Fix error with fabric service parameters causing performance issues
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:13:51 +01:00
James Smart 4169d868be [SCSI] lpfc 8.3.35: Fixed SCSI host create showing wrong link speed on SLI3 HBA ports
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:13:12 +01:00
James Smart 26979cedb0 [SCSI] lpfc 8.3.35: Fixed not checking solicition in progress bit when verifying FCF record for use
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:11:16 +01:00
James Smart 292098beb5 [SCSI] lpfc 8.3.35: Fixed messages for misconfigured port errors
Fixed messages for misconfigured port errors to be consistent for
all OS platforms.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:10:19 +01:00
James Smart 876dd7d06c [SCSI] lpfc 8.3.35: Fixed kernel warning on spinlock usage on some distributions
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:09:08 +01:00
James Smart 4c1b64bad4 [SCSI] lpfc 8.3.35: Fixed PRLI not being retried if a LS_RJT with a reason
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:03:43 +01:00
James Smart ce3962829d [SCSI] lpfc 8.3.35: Correct request_firmware use that was increasing boot times
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 12:00:21 +01:00
James Smart 2a94aea436 [SCSI] lpfc 8.3.35: Fix FCP2 Retries for non-r/w commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 11:57:44 +01:00
James Smart 5402a31581 [SCSI] lpfc 8.3.35: Fixed Linux generic firmware download on SLI4 devices with longer module names
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 11:55:41 +01:00
James Smart 82c3e9bafa [SCSI] lpfc 8.3.35: Expand I/O channel support for large systems
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 11:52:52 +01:00
James Smart 8831881644 [SCSI] lpfc 8.3.35: Correct missing queue destroy on function reset
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 11:51:45 +01:00
James Smart 005ffa7044 [SCSI] lpfc 8.3.35: Fix incorrect comment in T10 DIF attributes
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 11:51:00 +01:00
James Smart 2d843edc2b [SCSI] lpfc 8.3.35: Added checking BMBX register for RDY bit before writing the first address in
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 11:49:56 +01:00
James Smart ee02006b53 [SCSI] lpfc 8.3.35: Fix interrupt delay multipler conversion for eq_create
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-08 11:47:32 +01:00
Yi Zou 3b64b18811 [SCSI] libfc: fix lun reset failure bugs in fc_fcp_resp handling of FCP_RSP_INFO
In LUN RESET testing involving NetApp targets, it is observed that LUN
RESET is failing. The fc_fcp_resp() is not completing the completion
for the LUN RESET task since fc_fcp_resp assumes that the FCP_RSP_INFO
is 8 bytes with the 4 byte reserved field, where in case of NetApp targets
the FCP_RSP to LUN RESET only has 4 bytes of FCP_RSP_INFO. This leads
fc_fcp_resp to error out w/o completing the task completion, eventually
causing LUN RESET to be escalated to host reset, which is not very nice.

Per FCP-3 r04, clause 9.5.15 and Table 23, the FCP_RSP_INFO field can be either
4 bytes or 8 bytes, with the last 4 bytes as "Reserved (if any)". Therefore it
is valid to have 4 bytes FCP_RSP_INFO like some of the NetApp targets behave.
Fixing this by validating the FCP_RSP_INFO against both the two spec allowed
length.

Reported-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-07 11:52:55 +01:00
Neerav Parikh 31c37a6f21 [SCSI] fcoe: Fix write errors on NPIV ports
SCSI errors were generated while writing to LUNs
connected via NPIV ports.

Debugging this it was found that the FCoE packets
transmitted via the NPIV ports were not tagged with
correct user priority as negotiated with peer by DCB
agent. This resulted in FCoE traffic going with priority
zero(0) that did not have priority flow control (PFC)
enabled for it. The initiator after transferring data
to the target never saw any reply indicating the transfer
was complete. This resulted in error recovery (ABTS) and
SCSI command retries by the scsi-mid layer; eventually
resulting in I/O errors.

This patch fixes this issue by keeping the FCoE user
priority information in the fcoe_interface instance
that is common for both the physical port as well as
NPIV ports connected to that physical port; instead
of storing it in fcoe_port structure that has a per
port instance.

Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-07 11:49:34 +01:00
Shun Fu bd756ddea1 [SCSI] mvumi: Add support for Marvell SAS/SATA RAID-on-Chip(ROC) 88RC9580
[jejb: fix up for spelling correction patch]
Signed-off-by: Shun Fu <fushun@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-07 11:34:36 +01:00
Krishna Gudipati 08bc166d0f [SCSI] bfa: Update the driver version to 3.1.2.1
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-07 11:29:16 +01:00
Krishna Gudipati 7d0ecef383 [SCSI] bfa: Firmware image naming convention update
- Modified the firmware naming convention to contain the
  firmware image version (3.1.0.0).
- The new convention is <firmware-image>-<firmware-version>.bin
- The change will enforce loading only compatible firmware with this driver
  and also avoid over-writing the old firmware image in-order to load new
  version driver as the firmware names used to be the same.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-07 11:28:06 +01:00