Commit Graph

600 Commits

Author SHA1 Message Date
Minas Harutyunyan 5acb4b9701 dwc2: gadget: Fix completed transfer size calculation in DDMA
Fix calculation of transfer size on completion in function
dwc2_gadget_get_xfersize_ddma().

Added increment of descriptor pointer to move to next descriptor in
the loop.

Fixes: aa3e8bc813 ("usb: dwc2: gadget: DDMA transfer start and complete")

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:49 +03:00
Minas Harutyunyan 28b5c129ca usb: dwc2: Set lpm mode parameters depend on HW configuration
If core not supported lpm, i.e. BCM2835 then confusing warnings seen
in log.

To avoid these warnings, added function dwc2_set_param_lpm() to set
lpm and other lpm related parameters based on lpm support by core.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:49 +03:00
Minas Harutyunyan 5799aecd64 usb: dwc2: Fix channel disable flow
Channel disabling/halting should performed for enabled only channels
to avoid warnings "Unable to clear enable on channel N" which seen
if host works in Slave mode.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Minas Harutyunyan c8006f67ae usb: dwc2: Set actual frame number for completed ISOC transfer
On ISOC transfer completion, in DDMA mode, set actual frame
number returning to function driver in usb_request.

Due to core limitation, returning frame number is 11-bit wide.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Minas Harutyunyan 54f37f5663 usb: dwc2: gadget: Increase descriptors count for ISOC's
Some function drivers queueing more than 128 ISOC requests at a time.
To avoid "descriptor chain full" cases, increasing descriptors count
from MAX_DMA_DESC_NUM_GENERIC to MAX_DMA_DESC_NUM_HS_ISOC for ISOC's
only.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Minas Harutyunyan b4c53b4ac6 usb: dwc2: Delayed status support
Added delayed status support for Control transfers.

Tested in all 3 modes: Slave, BDMA and DDMA.
Performed tests: USB CV (Ch9 and MSC), Control Read/Write tests
using Synopsys USB test environment function driver.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Jules Maselbas 1e868545f2 usb: dwc2: gadget: Move gadget phy init into core phy init
Most of the phy initialization is shared between host and gadget,
this adds the turnaround configuration only used by gadgets to
the global phy init.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Jules Maselbas 059d8d5287 usb: dwc2: Move phy init into core
As the phy initialization is almost the same in host and gadget
mode. This only move the phy initialization functions into core.c
for now, the goal is to share theses functions between the two modes.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Jules Maselbas 707d80f0a3 usb: dwc2: gadget: Replace phyif with phy_utmi_width
The phy utmi width information is already set in hsotg params,
phyif is only used in few places and I don't see any reason to
not use hsotg's params.

Moreover the utmi width was being forced to 16 bits by platform
initialization which doesn't take in account HW configuration.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Jules Maselbas fb26b553bf usb: dwc2: gadget: Remove duplicated phy init
The function dwc2_hsotg_init is only called once just before calling
dwc2_hsotg_core_init_disconnected which does the same initialization:
setting the usbcfg register with turnaround time, timeout calibration
and phy width.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Jules Maselbas a89bae709b usb: dwc2: Move UTMI_PHY_DATA defines closer
Makes GHWCFG4_UTMI_PHY_DATA* defines closer to their relative shift and
mask defines to improve readability.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:48 +03:00
Douglas Anderson c40cf7705e usb: dwc2: optionally assert phy reset when waking up
On the rk3288 USB host-only port (the one that's not the OTG-enabled
port) the PHY can get into a bad state when a wakeup is asserted (not
just a wakeup from full system suspend but also a wakeup from
autosuspend).

We can get the PHY out of its bad state by asserting its "port reset",
but unfortunately that seems to assert a reset onto the USB bus so it
could confuse things if we don't actually deenumerate / reenumerate the
device.

We can also get the PHY out of its bad state by fully resetting it using
the reset from the CRU (clock reset unit), which does a more full
reset.  The CRU-based reset appears to actually cause devices on the bus
to be removed and reinserted, which fixes the problem (albeit in a hacky
way).

It's unfortunate that we need to do a full re-enumeration of devices at
wakeup time, but this is better than alternative of letting the bus get
wedged.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Chunfeng Yun 60722c4eef usb: dwc2: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.

Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Minas Harutyunyan 466375657d usb: dwc2: gadget: Reject LPM token during Control transfers
Avoiding switch to L1 state in any stage of control transfers.
Send NYET handshake to LPM token.

Renamed GLPMCFG_LPM_ACCEPT_CTRL_ISOC to GLPMCFG_LPM_REJECT_CTRL_CONTROL
because by setting this bit core reject LPM token.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Douglas Anderson 6f6d70597c usb: dwc2: bus suspend/resume for hosts with DWC2_POWER_DOWN_PARAM_NONE
This is an attempt to rehash commit 0cf884e819 ("usb: dwc2: add bus
suspend/resume for dwc2") on ToT.  That commit was reverted in commit
b0bb9bb6ce ("Revert "usb: dwc2: add bus suspend/resume for dwc2"")
because apparently it broke the Altera SOCFPGA.

With all the changes that have happened to dwc2 in the meantime, it's
possible that the Altera SOCFPGA will just magically work with this
change now.  ...and it would be good to get bus suspend/resume
implemented.

This change is a forward port of one that's been living in the Chrome
OS 3.14 kernel tree.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Neil Armstrong fc4e326ee7 usb: dwc2: Add Amlogic G12A DWC2 Params
This patchs sets the params for the DWC2 Controller found in the
Amlogic G12A SoC family.

It mainly sets the settings reported incorrect by the driver,
leaving the remaining detected automatically by the driver and
provided by the DT node.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Gustavo A. R. Silva eeca7606dd usb: dwc2: use struct_size() in kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-19 14:41:38 +01:00
Greg Kroah-Hartman dc8b2a691d USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
 changes which improve request cancellation and some improvements to
 how we print to the trace buffer.
 
 Renesas_usb3 got support for r8a774c0 device.
 
 Dwc2 got scatter-gather support.
 
 Apart from these, the usual set of minor fixes and all sorts of small
 details.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlxlU88dHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQYCTA/9EOtd5A2UkUkYIwh0
 uV1NOTMIcTnQeNLxOe1c/3yNo4pxGeaKkVc4g/3pdh9dQ121DxUdKy3KAJkDsqDe
 sbab7Ww2DZds17NqQfMloq3UyLjG2nCOJRl6UjoMCMcd4nVwi9by15W+NjBQSThw
 3qvv9qVHiP9O7rKyUOMH/aPqHno1cEb8YJoFDdQuYL3Gv6kbbhfjynBhIzO5W+Zq
 Za1aIayUEcbnk7OXLj2jUaaQS9TKb8zdhSXb8UGIuQkHQ/GbZF/Me/RbJif+KY7L
 P+A8PUrk08B/QKm5PdmPjl5MjjoXa8/sEVzOMqEG4vtT8loQ6WCm9k1NNvzHXPa3
 aRD316Yvp5EAPUBv3B8IrYUnLRH/xdG1YzEnDHrtsSwVN50qUXXUnvX2TkBic7M/
 kEmcB2TS1Pqlto0DUwuSlNUQ6KHDRIxoZ66jdxPfORMzEBWVtoIRLhLSG/oMXYFC
 SvwKKv2UY0Z/55sUEDuAR8VO3a/KI4FefcmeKsem5I4FfRdQ0SumNYmolpY7Kpqo
 BL3P+4LQ4CiNBNoBEfifKRUy/jEfU7fTDedgrua8zMH/c7zFXGL+SGNkIixRESO1
 B4Cl5/INP4slwtegvSsp3A/4hakPGyBhebCLKVZ/M71BeG0+1TPlAZruPO8SIiqc
 7FSxVk2X9Ic0mkXmSqnT7ItuLUU=
 =4fTL
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

USB: changes for v5.1 merge window

Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.

Renesas_usb3 got support for r8a774c0 device.

Dwc2 got scatter-gather support.

Apart from these, the usual set of minor fixes and all sorts of small
details.

* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
  usb: phy: twl6030-usb: fix possible use-after-free on remove
  usb: misc: usbtest: add super-speed isoc support
  usb: dwc3: Reset num_trbs after skipping
  usb: dwc3: gadget: don't enable interrupt when disabling endpoint
  fotg210-udc: pass struct device to DMA API functions
  fotg210-udc: remove a bogus dma_sync_single_for_device call
  usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
  usb: f_fs: Avoid crash due to out-of-scope stack ptr access
  usb: dwc3: haps: Workaround matching VID PID
  usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
  usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
  usb: gadget: function: sync f_uac1 ac header baInterfaceNr
  usb: dwc2: gadget: Add scatter-gather mode
  usb: gadget: fix various indentation issues
  usb: dwc2: Fix EP TxFIFO number setting
  udc: net2280: Fix net2280_disable
  USB: gadget: Improve kerneldoc for usb_ep_dequeue()
  usb: dwc3: debug: purge usage of strcat
  usb: dwc3: trace: pass trace buffer size to decoding functions
  usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
  ...
2019-02-15 09:08:57 +01:00
Andrzej Pietrasiewicz 10209abe87 usb: dwc2: gadget: Add scatter-gather mode
This patch adds support for transferring requests, which are
non-contiguous in physical memory, i.e. the data buffer is described by
a scatter-list. This allows transferring large requests without relying
on error-prone contiguous buffer allocations. This way of allocating
requests is already implemented in functionfs and TCM USB functions and
automatically used if UDC driver advertises scatter-gather suppport.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[mszyprow: fixed null pointer issue, rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-02-07 13:14:51 +02:00
Minas Harutyunyan 97311c8f8b usb: dwc2: Fix EP TxFIFO number setting
In case when some EP IN is frequently reused, i.e. enabled/disabled by
function driver. It is required to clear TxFIFO number field in DIEPCTL
register before setting new number. Otherwise there is probability to
have same TxFIFO number for different EP's because of OR operator.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-02-07 13:14:51 +02:00
Greg Kroah-Hartman c9381e185f Merge 5.0-rc4 into usb-next
We need the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-28 08:44:58 +01:00
Greg Kroah-Hartman cae8dc3b68 USB: add missing SPDX lines to Kconfig and Makefiles
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles.  Add
the correct GPL-2.0 identifier to them to make scanning tools happy.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-22 09:08:17 +01:00
Minas Harutyunyan 87b6d2c568 usb: dwc2: gadget: Fix Remote Wakeup interrupt bit clearing
To clear GINTSTS2_WKUP_ALERT_INT bit in GINTSTS2 register
require to write 1. This bit is implemented as "Write to clear".

Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-01-17 15:56:53 +02:00
Minas Harutyunyan 4fe4f9fecc usb: dwc2: Fix disable all EP's on disconnect
Disabling all EP's allow to reset EP's to initial state.
Introduced new function dwc2_hsotg_ep_disable_lock() which
before calling dwc2_hsotg_ep_disable() function acquire
hsotg->lock and release on exiting.
From dwc2_hsotg_ep_disable() function removed acquiring
hsotg->lock.
In dwc2_hsotg_core_init_disconnected() function when USB
reset interrupt asserted disabling all ep’s by
dwc2_hsotg_ep_disable() function.
This updates eliminating sparse imbalance warnings.

Reverted changes in dwc2_hostg_disconnect() function.
Introduced new function dwc2_hsotg_ep_disable_lock().
Changed dwc2_hsotg_ep_ops. Now disable point to
dwc2_hsotg_ep_disable_lock() function.
In functions dwc2_hsotg_udc_stop() and dwc2_hsotg_suspend()
dwc2_hsotg_ep_disable() function replaced by
dwc2_hsotg_ep_disable_lock() function.
In dwc2_hsotg_ep_disable() function removed acquiring
of hsotg->lock.

Fixes: dccf1bad4b ("usb: dwc2: Disable all EP's on disconnect")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-12-11 15:42:39 +02:00
Martin Blumenstingl cc10ce0c51 usb: dwc2: disable power_down on Amlogic devices
Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).

A similar fix was implemented for Rockchip SoCs in commit c216765d3a
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9caa ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").

Cc: <stable@vger.kernel.org> # 4.19
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-12-10 09:18:19 +02:00
Terin Stock 6ed30a7d8e usb: dwc2: host: use hrtimer for NAK retries
Modify the wait delay utilize the high resolution timer API to allow for
more precisely scheduled callbacks.

A previous commit added a 1ms retry delay after multiple consecutive
NAKed transactions using jiffies. On systems with a low timer interrupt
frequency, this delay may be significantly longer than specified,
resulting in misbehavior with some USB devices.

This scenario was reached on a Raspberry Pi 3B with a Macally FDD-USB
floppy drive (identified as 0424:0fdc Standard Microsystems Corp.
Floppy, based on the USB97CFDC USB FDC). With the relay delay, the drive
would be unable to mount a disk, replying with NAKs until the device was
reset.

Using ktime, the delta between starting the timer (in dwc2_hcd_qh_add)
and the callback function can be determined. With the original delay
implementation, this value was consistently approximately 12ms. (output
in us).

    <idle>-0     [000] ..s.  1600.559974: dwc2_wait_timer_fn: wait_timer delta: 11976
    <idle>-0     [000] ..s.  1600.571974: dwc2_wait_timer_fn: wait_timer delta: 11977
    <idle>-0     [000] ..s.  1600.583974: dwc2_wait_timer_fn: wait_timer delta: 11976
    <idle>-0     [000] ..s.  1600.595974: dwc2_wait_timer_fn: wait_timer delta: 11977

After converting the relay delay to using a higher resolution timer, the
delay was much closer to 1ms.

    <idle>-0     [000] d.h.  1956.553017: dwc2_wait_timer_fn: wait_timer delta: 1002
    <idle>-0     [000] d.h.  1956.554114: dwc2_wait_timer_fn: wait_timer delta: 1002
    <idle>-0     [000] d.h.  1957.542660: dwc2_wait_timer_fn: wait_timer delta: 1004
    <idle>-0     [000] d.h.  1957.543701: dwc2_wait_timer_fn: wait_timer delta: 1002

The floppy drive operates properly with delays up to approximately 5ms,
and sends NAKs for any delays that are longer.

Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Terin Stock <terin@terinstock.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-12-05 11:13:14 +02:00
Marek Szyprowski 35a6054132 usb: dwc2: Disable power down feature on Samsung SoCs
Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.

Fixes: 03ea6d6e9e ("usb: dwc2: Enable power down")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-12-05 11:09:08 +02:00
Artur Petrosyan 9aed8c08c8 usb: dwc2: gadget: Accept LPM token when TxFIFO is not empty
Set GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG register
to accept LPM token during ISOC transfers when TxFIFO is
not empty.

- Added two definitions.
  	#define GLPMCFG_LPM_ACCEPT_CTRL_CONTROL        BIT(21)
  	#define GLPMCFG_LPM_ACCEPT_CTRL_ISOC   BIT(22)
  This patch uses GLPMCFG_LPM_ACCEPT_CTRL_ISOC.
  GLPMCFG_LPM_ACCEPT_CTRL_CONTROL is defined for further use.

- Added setting GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG
  register in dwc2_gadget_init_lpm function.

Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-11-26 09:06:32 +02:00
Artur Petrosyan d64bc8ee92 usb: dwc2: gadget: Fix WkupAlert interrupt handler.
According to the databook DCTL_RMTWKUPSIG bit
is defined in DCTL register not in DCFG.

Updated setting DCTL_RMTWKUPSIG bit to DCTL
register.

Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")

Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-11-26 09:06:32 +02:00
Dan Carpenter 3c135e8900 usb: dwc2: pci: Fix an error code in probe
We added some error handling to this function but forgot to set the
error code on this path.

Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-11-14 11:07:12 +02:00
SolidHal c216765d3a usb: dwc2: disable power_down on rockchip devices
The bug would let the usb controller enter partial power down,
 which was formally known as hibernate, upon boot if nothing was plugged
 in to the port. Partial power down couldn't be exited properly, so any
 usb devices plugged in after boot would not be usable.

 Before the name change, params.hibernation was false by default, so
 _dwc2_hcd_suspend() would skip entering hibernation. With the
 rename, _dwc2_hcd_suspend() was changed to use  params.power_down
 to decide whether or not to enter partial power down.

 Since params.power_down is non-zero by default, it needs to be set
 to 0 for rockchip devices to restore functionality.

 This bug was reported in the linux-usb thread:
 REGRESSION: usb: dwc2: USB device not seen after boot

 The commit that caused this regression is:
6d23ee9caa

Signed-off-by: SolidHal <hal@halemmerich.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-05 10:50:14 +03:00
Grigor Tovmasyan 187c5298a1 usb: dwc2: gadget: Add handler for WkupAlert interrupt
Added interrupt handler for WkupAlert interrupt.

This interrupt should initiate Remote Wake up.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:50:43 +03:00
Grigor Tovmasyan 4abe453750 usb: dwc2: gadget: enable WKUP_ALERT interrupt
WKUP_ALERT interrupt should be unmask when lpm mode is enabled.

This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:50:34 +03:00
Grigor Tovmasyan 15d9dbf8cb usb: dwc2: gadget: Program GREFCLK register
Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:50:22 +03:00
Grigor Tovmasyan f3a61e4e03 usb: dwc2: gadget: Add parameters for GREFCLK register
Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:50:09 +03:00
Grigor Tovmasyan 392af02326 usb: dwc2: Add definitions for new registers
New registers were added to dwc otg core.

GREFCLK - This register used to control ref_clk parameters.

GINTSTS2 - New WKUP_ALERT interrupt was added.

GINTMSK2 - Mask register for GINTSTS2.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:49:59 +03:00
Grigor Tovmasyan 48dac4e4a5 usb: dwc2: Update target (u)frame calculation
In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:49:50 +03:00
Grigor Tovmasyan 9d630b9cde usb: dwc2: Add dwc2_gadget_dec_frame_num_by_one() function
Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:49:38 +03:00
Grigor Tovmasyan ca531bc2bf usb: dwc2: Add core parameter for service interval support
Added core parameter for service interval based scheduling.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:49:26 +03:00
Grigor Tovmasyan c464da0bff usb: dwc2: Update registers definitions to support service interval
Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:49:13 +03:00
Fabrice Gasnier cd7cd0e6ce usb: dwc2: fix unbalanced use of external vbus-supply
When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).

Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")

Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:37:40 +03:00
Fabrice Gasnier 5aa678c7fd usb: dwc2: fix call to vbus supply exit routine, call it unlocked
dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.

Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")

Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:37:26 +03:00
Fabrice Gasnier 41ee1ea210 usb: dwc2: fix a race with external vbus supply
There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.

Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")

Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:37:11 +03:00
Fabrice Gasnier e0f681c2c1 usb: dwc2: get optional vbus-supply regulator once
Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.

Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")

Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:37:01 +03:00
Minas Harutyunyan dccf1bad4b usb: dwc2: Disable all EP's on disconnect
Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.

Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:33:15 +03:00
Josh Abraham 971a0d4e1b usb: dwc2: remove set but unused variable
This patch removes a set but unused variable in hcd.c.

Fixes gcc warning:
variable ‘data_fifo’ set but not used [-Wunused-but-set-variable]

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-10-02 10:29:42 +03:00
Bruno Meirelles Herrera d970749007 usb: dwc2: Fix call location of dwc2_check_core_endianness
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:

[    1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[    1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[    1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[    2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[    2.015176] dwc2: probe of 50000000.usb failed with error -16

The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-09-05 13:12:31 +03:00
Greg Kroah-Hartman 45dd7af410 usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
 are touching dwc2 (74% of the changes).
 
 The most important changes are dwc2's support for uframe scheduling
 and its endian-agnostic readl/writel wrappers.
 
 From dwc3 side we have a special new glue layer for Synopsys HAPS
 which will help Synopsys running FPGA validation using our upstream
 driver. We also have the beginnings of dual-role support for Intel
 Merrifield platform.
 
 Apart from these, just a series of non-critical changes.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAltewsEdHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQaV8BAAziA9QIT6to7Zzd7t
 tsfU3chXUS2t+fZ6drADdHHwJTvjCT4D9FbpYFSNC9lanSLB+IwQ6rZGglyyPh5P
 DVcWObi8wR1+w8gcx+NL65XuzM/oM8Sx+zSA+3hV7H8A1ePikd+wFpXcZhY0zoLS
 00BoAf66CvRvGAGX8e1HouL4LPs/V5vllxcObKLrzcziCNziLhAy1MkONAwSagvP
 JA50nh0Jau6p/+inF/931oeixmVvTV0xJjqveIf6cVsyv9jNy+I53rFwVsaiSVLz
 dvzrnPmzWbT4F1yuLgqXccd68FF4Zm+Vl+uHyzaZ7b8e1JK7ABg9a7Us6CjP9HXq
 aw63hUKmrsTsTyLCWkoU6ypeCYJF3Et49pzicLRFOdXufWJLTRa0iNbgyf8gNOQt
 K8igJZkmHnb4RByLITtHot3Qdpn2Mr+8Cu/H4TpqQBAKom6mxdwkfm4lojBzLoRn
 IIr81yTJD00uqgQ40IeoFyV5zz4CqMti3GQX8QXO2wdbrKlaLCr4UDuu4llE2AJ9
 1cYV8SMoC2yXaGsshe2dvCq4/lhxiOXPBNoR/GvtvXd84AXaYCsuphUhSGTybYLG
 a3LO72mn4R8hAnqzh3+xyC4Irs9hgVJUKOD7fFn0ZPvCXgLUQIYRimIprEQ0EsCI
 /lcdOwOheSGM9Fq5U/fcWDdZcmE=
 =HiNz
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: changes for v4.19

Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).

The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.

From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.

Apart from these, just a series of non-critical changes.
2018-07-30 10:21:14 +02:00
Douglas Anderson f8781d5509 usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on stm32f4x9_fsotg since commit
e35b135055 ("usb: dwc2: Add support for STM32F429/439/469 USB OTG
HS/FS in FS mode (internal PHY)").  That commit is pretty recent, so
it's unclear to me why the uframe scheduler was left off.  Hopefully
it's because someone copied it from other parameters and didn't think
to try it?

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.

Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-07-30 10:39:19 +03:00
Douglas Anderson 3af0540ad3 usb: dwc2: Turn on uframe_sched on "amlogic" platforms
There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on Amlogic since commit f94310ac07
("usb: dwc2: add support for Meson8b and GXBB SoCs").  While this was
after most of the recent improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler"), presumably
the parameters were copied from another platform and the uframe
scheduler wasn't tried.

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.

Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-07-30 10:39:19 +03:00