Commit Graph

95 Commits

Author SHA1 Message Date
John W. Linville c3d34d5d96 wireless: register wiphy rfkill w/o holding cfg80211_mutex
Otherwise lockdep complains...

https://bugzilla.kernel.org/show_bug.cgi?id=17311

[ INFO: possible circular locking dependency detected ]
2.6.36-rc2-git4 #12
-------------------------------------------------------
kworker/0:3/3630 is trying to acquire lock:
 (rtnl_mutex){+.+.+.}, at: [<ffffffff813396c7>] rtnl_lock+0x12/0x14

but task is already holding lock:
 (rfkill_global_mutex){+.+.+.}, at: [<ffffffffa014b129>]
rfkill_switch_all+0x24/0x49 [rfkill]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (rfkill_global_mutex){+.+.+.}:
       [<ffffffff81079ad7>] lock_acquire+0x120/0x15b
       [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e
       [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39
       [<ffffffffa014b4ab>] rfkill_register+0x2b/0x29c [rfkill]
       [<ffffffffa0185ba0>] wiphy_register+0x1ae/0x270 [cfg80211]
       [<ffffffffa0206f01>] ieee80211_register_hw+0x1b4/0x3cf [mac80211]
       [<ffffffffa0292e98>] iwl_ucode_callback+0x9e9/0xae3 [iwlagn]
       [<ffffffff812d3e9d>] request_firmware_work_func+0x54/0x6f
       [<ffffffff81065d15>] kthread+0x8c/0x94
       [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10

-> #1 (cfg80211_mutex){+.+.+.}:
       [<ffffffff81079ad7>] lock_acquire+0x120/0x15b
       [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e
       [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39
       [<ffffffffa018605e>] cfg80211_get_dev_from_ifindex+0x1b/0x7c [cfg80211]
       [<ffffffffa0189f36>] cfg80211_wext_giwscan+0x58/0x990 [cfg80211]
       [<ffffffff8139a3ce>] ioctl_standard_iw_point+0x1a8/0x272
       [<ffffffff8139a529>] ioctl_standard_call+0x91/0xa7
       [<ffffffff8139a687>] T.723+0xbd/0x12c
       [<ffffffff8139a727>] wext_handle_ioctl+0x31/0x6d
       [<ffffffff8133014e>] dev_ioctl+0x63d/0x67a
       [<ffffffff8131afd9>] sock_ioctl+0x48/0x21d
       [<ffffffff81102abd>] do_vfs_ioctl+0x4ba/0x509
       [<ffffffff81102b5d>] sys_ioctl+0x51/0x74
       [<ffffffff81009e02>] system_call_fastpath+0x16/0x1b

-> #0 (rtnl_mutex){+.+.+.}:
       [<ffffffff810796b0>] __lock_acquire+0xa93/0xd9a
       [<ffffffff81079ad7>] lock_acquire+0x120/0x15b
       [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e
       [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39
       [<ffffffff813396c7>] rtnl_lock+0x12/0x14
       [<ffffffffa0185cb5>] cfg80211_rfkill_set_block+0x1a/0x7b [cfg80211]
       [<ffffffffa014aed0>] rfkill_set_block+0x80/0xd5 [rfkill]
       [<ffffffffa014b07e>] __rfkill_switch_all+0x3f/0x6f [rfkill]
       [<ffffffffa014b13d>] rfkill_switch_all+0x38/0x49 [rfkill]
       [<ffffffffa014b821>] rfkill_op_handler+0x105/0x136 [rfkill]
       [<ffffffff81060708>] process_one_work+0x248/0x403
       [<ffffffff81062620>] worker_thread+0x139/0x214
       [<ffffffff81065d15>] kthread+0x8c/0x94
       [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
2010-08-31 14:48:47 -04:00
Joe Perches 073730d771 wireless: Convert wiphy_debug macro to function
Save a few bytes of text

(allyesconfig)
$ size drivers/net/wireless/built-in.o*
   text	   data	    bss	    dec	    hex	filename
3924568	 100548	 871056	4896172	 4ab5ac	drivers/net/wireless/built-in.o.new
3926520	 100548	 871464	4898532	 4abee4	drivers/net/wireless/built-in.o.old

$ size net/wireless/core.o*
   text	   data	    bss	    dec	    hex	filename
  12843	    216	   3768	  16827	   41bb	net/wireless/core.o.new
  12328	    216	   3656	  16200	   3f48	net/wireless/core.o

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-27 15:14:13 -04:00
Maxime Bizon 5a652052fe cfg80211: fix race between sysfs and cfg80211
device_add() is called before adding the phy to the cfg80211 device
list.

So if a userspace program uses sysfs uevents to detect new phy
devices, and queries nl80211 to get phy info, it can get ENODEV even
though the phy exists in sysfs.

An easy workaround is to hold the cfg80211 mutex until the phy is
present in sysfs/cfg80211/debugfs.

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-21 15:13:42 -04:00
Uwe Kleine-König f884e3879b cfg80211: move cfg80211_exit to .exit.text
cfg80211_exit is only used as module_exit function, so it can go to
.exit.text saving a few bytes when CONFIG_CFG80211=y.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-18 15:11:13 -04:00
John W. Linville 83163244f8 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	drivers/net/wireless/libertas_tf/cmd.c
	drivers/net/wireless/libertas_tf/main.c
2010-05-05 16:14:16 -04:00
Juuso Oikarinen 9043f3b89a cfg80211: Remove default dynamic PS timeout value
Now that the mac80211 is choosing dynamic ps timeouts based on the ps-qos
network latency configuration, configure a default value of -1 as the dynamic
ps timeout in cfg80211. This value allows the mac80211 to determine the value
to be used.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:22 -04:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Kalle Valo ffb9eb3d8b nl80211: add power save commands
The most needed command from nl80211, which Wireless Extensions had,
is support for power save mode. Add a simple command to make it possible
to enable and disable power save via nl80211.

I was also planning about extending the interface, for example adding the
timeout value, but after thinking more about this I decided not to do it.
Basically there were three reasons:

Firstly, the parameters for power save are very much hardware dependent.
Trying to find a unified interface which would work with all hardware, and
still make sense to users, will be very difficult.

Secondly, IEEE 802.11 power save implementation in Linux is still in state
of flux. We have a long way to still to go and there is no way to predict
what kind of implementation we will have after few years. And because we
need to support nl80211 interface a long time, practically forever, adding
now parameters to nl80211 might create maintenance problems later on.

Third issue are the users. Power save parameters are mostly used for
debugging, so debugfs is better, more flexible, interface for this.
For example, wpa_supplicant currently doesn't configure anything related
to power save mode. It's better to strive that kernel can automatically
optimise the power save parameters, like with help of pm qos network
and other traffic parameters.

Later on, when we have better understanding of power save, we can extend
this command with more features, if there's a need for that.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-19 15:52:40 -05:00
Jouni Malinen 026331c4d9 cfg80211/mac80211: allow registering for and sending action frames
This implements a new command to register for action frames
that userspace wants to handle instead of the in-kernel
rejection. It is then responsible for rejecting ones that
it decided not to handle. There is no unregistration, but
the socket can be closed for that.

Frames that are not registered for will not be forwarded
to userspace and will be rejected by the kernel, the
cfg80211 API helps implementing that.

Additionally, this patch adds a new command that allows
doing action frame transmission from userspace. It can be
used either to exchange action frames on the current
operational channel (e.g., with the AP with which we are
currently associated) or to exchange off-channel Public
Action frames with the remain-on-channel command.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-15 16:14:15 -05:00
Johannes Berg ef15aac607 cfg80211: export multiple MAC addresses in sysfs
If a device has multiple MAC addresses, userspace will
need to know about that. Similarly, if it allows the
MAC addresses to vary by a bitmask.

If a driver exports multiple addresses, it is assumed
that it will be able to deal with that many different
addresses, which need not necessarily match the ones
programmed into the device; if a mask is set then the
device should deal addresses within that mask based
on an arbitrary "base address".

To test it all and show how it is used, add support
to hwsim even though it can't actually deal with
addresses different from the default.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22 16:11:16 -05:00
Johannes Berg 5f2aa25e0e cfg80211: rcu-ify rdev and wdev
Future code will need to look up rdev and wdev
within atomic sections, but currently we need
to lock a mutex for such lookups. Change the
list handling for both to be RCU-safe so that
we can look them up in rcu sections instead in
the future.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19 16:43:09 -05:00
John W. Linville 031cf0e94c Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2010-01-19 15:58:41 -05:00
Lukáš Turek 81077e82c3 nl80211: Add new WIPHY attribute COVERAGE_CLASS
The new attribute NL80211_ATTR_WIPHY_COVERAGE_CLASS sets IEEE 802.11
Coverage Class, which depends on maximum distance of nodes in a
wireless network. It's required for long distance links (more than a few
hundred meters).

The attribute is now ignored by two non-mac80211 drivers, rndis and
iwmc3200wifi, together with WIPHY_PARAM_RETRY_SHORT and
WIPHY_PARAM_RETRY_LONG. If it turns out to be a problem, we could split
set_wiphy_params callback or add new capability bits.

Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-12 13:49:17 -05:00
Johannes Berg 8c5d9808e9 cfg80211: fix refcount imbalance when wext is disabled
When CONFIG_CFG80211_WEXT is not set, there is
a refcount imbalance with rdev->opencount, fix
that by moving it out of the ifdef.

Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-11 19:37:09 -05:00
Alban Browaeys e60d7443e0 wireless : use a dedicated workqueue for cfg80211.
This patch moves the works cleanup, scan and events to a cfg80211
dedicated workqueue.

Platform driver like eeepc-laptop ought to use works to rfkill (as
new rfkill does lock in rfkill_unregister and the platform driver is
called from rfkill_switch_all which also lock the same mutex).
This raise a new issue in itself that the work scheduled by the platform
driver to the global worqueue calls wiphy_unregister which flush_work
scan and event works (which thus flush works on the global workqueue inside
a work on the global workqueue) and also put on hold the  wdev_cleanup_work
 (which prevents the dev_put on netdev thus indefinite Usage count error on
wifi device).

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-28 15:05:00 -05:00
David S. Miller 4ba3eb034f Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2009-11-24 15:01:29 -08:00
Johannes Berg ad4bb6f888 cfg80211: disallow bridging managed/adhoc interfaces
A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
 * transmitter, which must be equal to the sender (origin)
 * receiver (on the wireless medium), which is the AP in
   the case of managed mode
 * the recipient (destination), which is on the APs local
   network segment

In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.

To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.

Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19 11:08:54 -05:00
Johannes Berg 5be83de54c cfg80211: convert bools into flags
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19 11:08:50 -05:00
David S. Miller 3505d1a9fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/sfc/sfe4001.c
	drivers/net/wireless/libertas/cmd.c
	drivers/staging/Kconfig
	drivers/staging/Makefile
	drivers/staging/rtl8187se/Kconfig
	drivers/staging/rtl8192e/Kconfig
2009-11-18 22:19:03 -08:00
Johannes Berg 7bcfaf2f43 cfg80211/mac80211: use debugfs_remove_recursive
We can save a lot of code and pointers in the structs
by using debugfs_remove_recursive().

First, change cfg80211 to use debugfs_remove_recursive()
so that drivers do not need to clean up any files they
added to the per-wiphy debugfs (if and only if they are
ok to be accessed until after wiphy_unregister!).

Then also make mac80211 use debugfs_remove_recursive()
where necessary -- it need not remove per-wiphy files
as cfg80211 now removes those, but netdev etc. files
still need to be handled but can now be removed without
needing struct dentry pointers to all of them.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-30 16:49:18 -04:00
Alexey Dobriyan d43c36dc6b headers: remove sched.h from interrupt.h
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
2009-10-11 11:20:58 -07:00
John W. Linville 4890e3bedd wireless: implement basic ethtool support for cfg80211 devices
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:45 -04:00
Johannes Berg 3d23e349d8 wext: refactor
Refactor wext to
 * split out iwpriv handling
 * split out iwspy handling
 * split out procfs support
 * allow cfg80211 to have wireless extensions compat code
   w/o CONFIG_WIRELESS_EXT

After this, drivers need to
 - select WIRELESS_EXT	- for wext support
 - select WEXT_PRIV	- for iwpriv support
 - select WEXT_SPY	- for iwspy support

except cfg80211 -- which gets new hooks in wext-core.c
and can then get wext handlers without CONFIG_WIRELESS_EXT.

Wireless extensions procfs support is auto-selected
based on PROC_FS and anything that requires the wext core
(i.e. WIRELESS_EXT or CFG80211_WEXT).

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07 16:39:43 -04:00
Marcel Holtmann 053a93dd12 cfg80211: assign device type in netdev notifier callback
Instead of having to modify every non-mac80211 for device type assignment,
do this inside the netdev notifier callback of cfg80211. So all drivers
that integrate with cfg80211 will export a proper device type.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-05 00:43:34 -07:00
Johannes Berg 3d54d25515 cfg80211: clean up properly on interface type change
When the interface type changes while connected, and the
driver does not require the interface to be down for a
type change, it is currently possible to get very strange
results unless the driver takes special care, which it
shouldn't have to.

To fix this, take care to disconnect/leave IBSS when
changing the interface type -- even if the driver may fail
the call. Also process all events that may be pending to
avoid running into a situation where an event is reported
but only processed after the type has already changed,
which would lead to missing events and warnings.

A side effect of this is that you will have disconnected
or left the IBSS even if the mode change ultimately fails,
but since the intention was to change it and thus leave or
disconnect, this is not a problem.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28 14:40:31 -04:00
Johannes Berg 01a0ac417c cfg80211: check lost scans later, fix bug
When we lose a scan, cfg80211 tries to clean up after
the driver. However, it currently does this too early,
it does this in GOING_DOWN already instead of DOWN, so
it may happen with mac80211. Besides fixing this, also
make it more robust by leaking the scan request so if
the driver later actually finishes the scan, it won't
crash. Also check in ___cfg80211_scan_done whether a
scan request is still pending and exit if not.

Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28 14:40:25 -04:00
Zhu Yi 16a832e785 cfg80211: allow cfg80211_connect_result with bssid == NULL
In case of connection failure, the bssid info is not a must have.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20 11:36:07 -04:00
Johannes Berg ad002395fd cfg80211: fix dangling scan request checking
My patch "cfg80211: fix deadlock" broke the code it
was supposed to fix, the scan request checking. But
it's not trivial to put it back the way it was, since
the original patch had a deadlock.

Now do it in a completely new way: queue the check
off to a work struct, where we can freely lock. But
that has some more complications, like needing to
wait for it to be done before the wiphy/rdev can be
destroyed, so some code is required to handle that.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20 11:36:05 -04:00
Johannes Berg 0ff6ce7b36 cfg80211: fix deadlock
When removing an interface with nl80211, cfg80211 will
deadlock in the netdev notifier because we're already
holding rdev->mtx and try to acquire it again to verify
the scan has been done.

This bug was introduced by my patch
"cfg80211: check for and abort dangling scan requests".

To fix this, move the dangling scan request check into
wiphy_unregister(). This will not be able to catch all
cases right away, but if the scan problem happens with
a manual ifdown or so it will be possible to remedy it
by removing the module/device.

Additionally, add comments about the deadlock scenario.

Reported-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-20 11:35:56 -04:00
Johannes Berg 16cb9d42b6 cfg80211: allow driver to override PS default
Sometimes drivers might have a good reason to override
the PS default, like iwlwifi right now where it affects
RX performance significantly at this point. This will
allow them to override the default, if desired, in a
way that users can still change it according to their
trade-off choices, not the driver's, like would happen
if the driver just disabled PS completely then.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14 09:14:08 -04:00
Johannes Berg 36e6fea849 cfg80211: check for and abort dangling scan requests
If you trigger a scan request on an interface and then
take it down, or rmmod the module or unplug the device
the driver might "forget" to cancel the scan request.
That is a bug in the driver, but the current behaviour
is that we just hang endlessly waiting for the netdev
refcount to become 0 which it never will. To improve
robustness, check for this situation in cfg80211, warn
about it and clean up behind the driver. I don't just
clean up silently because it's likely that the driver
also has some internal state it has now leaked.

Additionally, this fixes a locking bug, clearing the
scan_req pointer should be done under the rdev lock.

Finally, we also need to _wait_ for the scan work and
not just abort it since it might be pending and wanting
to do a cleanup.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14 09:14:07 -04:00
Johannes Berg aee83eaff8 cfg80211: add missing device list locking
When calling into the wext code from the NETDEV_UP
notifier, we need to hold the devlist_mtx mutex as
the wext code ends up calling into channel checks.

Reported-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14 09:13:54 -04:00
Johannes Berg f5ea9120be nl80211: add generation number to all dumps
In order for userspace to be able to figure out whether
it obtained a consistent snapshot of data or not when
using netlink dumps, we need to have a generation number
in each dump message that indicates whether the list has
changed or not -- its value is arbitrary.

This patch adds such a number to all dumps, this needs
some mac80211 involvement to keep track of a generation
number to start with when adding/removing mesh paths or
stations.

The wiphy and netdev lists can be fully handled within
cfg80211, of course, but generation numbers need to be
stored there as well.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14 09:13:43 -04:00
Johannes Berg 75e6c3b72b cfg80211: lower dynamic PS timeout to 100ms
The default of 500ms is pretty high, and leads
to the device being awake at least 50% of the
time under such light traffic conditions as a
simple 1 second interval ping. Reduce to just
100ms -- it should have a similar effect while
providing a better sleep time.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:20 -04:00
Luis R. Rodriguez abc7381bcc cfg80211: decouple regulatory variables from cfg80211_mutex
We change regulatory code to be protected by its own regulatory
mutex and alleviate cfg80211_mutex to only be used to protect
cfg80211_rdev_list, the registered device list.

By doing this we will be able to work on regulatory core components
without having to have hog up the cfg80211_mutex. An example here is
we no longer need to use the cfg80211_mutex during driver specific
wiphy_apply_custom_regulatory(). We also no longer need it for the
the country IE regulatory hint; by doing so we end up curing this
new lockdep warning:

=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #12
-------------------------------------------------------
phy1/1709 is trying to acquire lock:
 (cfg80211_mutex){+.+.+.}, at: [<ffffffffa00af852>] regulatory_hint_11d+0x32/0x3f0 [cfg80211]

but task is already holding lock:
 (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 (&ifmgd->mtx){+.+.+.}:
       [<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
       [<ffffffff81085dd3>] lock_acquire+0xe3/0x120
       [<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
       [<ffffffffa0141bb8>] ieee80211_mgd_auth+0x108/0x1f0 [mac80211]
       [<ffffffffa0148563>] ieee80211_auth+0x13/0x20 [mac80211]
       [<ffffffffa00bc3a1>] __cfg80211_mlme_auth+0x1b1/0x2a0 [cfg80211]
       [<ffffffffa00bc516>] cfg80211_mlme_auth+0x86/0xc0 [cfg80211]
       [<ffffffffa00b368d>] nl80211_authenticate+0x21d/0x230 [cfg80211]
       [<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
       [<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
       [<ffffffff814169d9>] genl_rcv+0x29/0x40
       [<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
       [<ffffffff81416514>] netlink_sendmsg+0x214/0x300
       [<ffffffff813e4407>] sock_sendmsg+0x107/0x130
       [<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
       [<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

-> #2 (&wdev->mtx){+.+.+.}:
       [<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
       [<ffffffff81085dd3>] lock_acquire+0xe3/0x120
       [<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
       [<ffffffffa00ab304>] cfg80211_netdev_notifier_call+0x1a4/0x390 [cfg80211]
       [<ffffffff814f3dff>] notifier_call_chain+0x3f/0x80
       [<ffffffff81075a91>] raw_notifier_call_chain+0x11/0x20
       [<ffffffff813f665a>] dev_open+0x10a/0x120
       [<ffffffff813f59bd>] dev_change_flags+0x9d/0x1e0
       [<ffffffff8144eb6e>] devinet_ioctl+0x6fe/0x760
       [<ffffffff81450204>] inet_ioctl+0x94/0xc0
       [<ffffffff813e25fa>] sock_ioctl+0x6a/0x290
       [<ffffffff8111e911>] vfs_ioctl+0x31/0xa0
       [<ffffffff8111ea9a>] do_vfs_ioctl+0x8a/0x5c0
       [<ffffffff8111f069>] sys_ioctl+0x99/0xa0
       [<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

-> #1 (&rdev->mtx){+.+.+.}:
       [<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
       [<ffffffff81085dd3>] lock_acquire+0xe3/0x120
       [<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
       [<ffffffffa00ac4d0>] cfg80211_get_dev_from_ifindex+0x60/0x90 [cfg80211]
       [<ffffffffa00b21ff>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
       [<ffffffffa00b51eb>] nl80211_set_interface+0x3b/0x260 [cfg80211]
       [<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
       [<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
       [<ffffffff814169d9>] genl_rcv+0x29/0x40
       [<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
       [<ffffffff81416514>] netlink_sendmsg+0x214/0x300
       [<ffffffff813e4407>] sock_sendmsg+0x107/0x130
       [<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
       [<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

other info that might help us debug this:

3 locks held by phy1/1709:
 #0:  ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
 #1:  (&ifmgd->work){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
 #2:  (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]

Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:18 -04:00
Johannes Berg e40cbdac06 cfg80211: fix NETDEV_UNREGISTER notifier
It's possible to get the NETDEV_UNREGISTER callback multiple
times (see net/core/dev.c:netdev_wait_allrefs) and this will
completely mess up our cleanup code. To avoid that, clean up
only when the interface is still on the wiphy interface list
from which it's removed on the first NETDEV_UNREGISTER call.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:15 -04:00
Johannes Berg df7fc0f973 cfg80211: keep track of current_bss for userspace SME
When a userspace SME is active, we're currently not
keeping track of the BSS properly for reporting the
current link and for internal use. Additionally, it
looks like there is a possible BSS leak in that the
BSS never gets removed from auth_bsses[]. To fix it,
pass the BSS struct to __cfg80211_connect_result in
this case.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:24 -04:00
Johannes Berg a9a11622c5 cfg80211: self-contained wext handling where possible
Finally! This is what you've all been waiting for!

This patch makes cfg80211 take care of wext emulation
_completely_ by itself, drivers that don't need things
cfg80211 doesn't do yet don't even need to be aware of
wireless extensions.
This means we can also clean up mac80211's and iwm's
Kconfig and make it possible to build them w/o wext
now!

		RIP wext.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-29 15:46:20 -04:00
Johannes Berg 463d018323 cfg80211: make aware of net namespaces
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:

 * del_virtual_intf method takes an interface index rather
   than a netdev pointer - simply change this

 * nl80211 uses init_net a lot, it changes to use the sender's
   network namespace

 * scan requests use the interface index, hold a netdev pointer
   and reference instead

 * we want a wiphy and its associated virtual interfaces to be
   in one netns together, so
    - we need to be able to change ns for a given interface, so
      export dev_change_net_namespace()
    - for each virtual interface set the NETIF_F_NETNS_LOCAL
      flag, and clear that flag only when the wiphy changes ns,
      to disallow breaking this invariant

 * when a network namespace goes away, we need to reparent the
   wiphy to init_net

 * cfg80211 users that support creating virtual interfaces must
   create them in the wiphy's namespace, currently this affects
   only mac80211

The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
	iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27 15:24:07 -04:00
Johannes Berg 6682588a08 cfg80211: fix unregistration
The work that we cancel there requires the cfg80211_mutex,
so we can't cancel it under the mutex, which is fine, we
can just move it to after the locked section.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24 15:05:13 -04:00
Johannes Berg fffd0934b9 cfg80211: rework key operation
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.

In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.

Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24 15:05:09 -04:00
Johannes Berg 0b20633d96 cfg80211: disallow configuring unsupported interfaces
In order to force drivers to advertise their interface
types, don't just disallow creating new interfaces with
unadvertised types but also disallow setting them UP.
Additionally, add some validation on the operations the
drivers support.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:02:33 -04:00
Johannes Berg 79c97e97ae cfg80211: clean up naming once and for all
We've named the registered devices 'drv' sometimes,
thinking of "driver", which is not what it is, it's
the internal representation of a wiphy, i.e. a
device. Let's clean up the naming once and and use
'rdev' aka 'registered device' everywhere.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:02:33 -04:00
Johannes Berg 667503ddcb cfg80211: fix locking
Over time, a lot of locking issues have crept into
the smarts of cfg80211, so e.g. scan completion can
race against a new scan, IBSS join can race against
leaving an IBSS, etc.

Introduce a new per-interface lock that protects
most of the per-interface data that we need to keep
track of, and sprinkle assertions about that lock
everywhere. Some things now need to be offloaded to
work structs so that we don't require being able to
sleep in functions the drivers call. The exception
to that are the MLME callbacks (rx_auth etc.) that
currently only mac80211 calls because it was easier
to do that there instead of in cfg80211, and future
drivers implementing those calls will, if they ever
exist, probably need to use a similar scheme like
mac80211 anyway...

In order to be able to handle _deauth and _disassoc
properly, introduce a cookie passed to it that will
determine locking requirements.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:02:32 -04:00
Johannes Berg 4d0c8aead3 cfg80211: properly name driver locking
Currently we call that cfg80211_put_dev(), but that is
misleading. With the new convention of using 'rdev' for
registered_device variables, also call that function
cfg80211_unlock_rdev().

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:02:32 -04:00
Johannes Berg 7848547561 cfg80211: fix netdev down problem
We shouldn't be looking at the ssid_len for non-IBSS,
and for IBSS we should also return an error on trying
to leave an IBSS while not in or joining an IBSS.

This fixes an issue where we wouldn't disconnect() on
an interface being taken down since there's no SSID
configured this way.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:02:31 -04:00
Johannes Berg 19957bb399 cfg80211: keep track of BSSes
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:01:53 -04:00
Johannes Berg 0eb14647fc cfg80211: reset auth algorithm
When the interface is brought down, we need to
reset the auth algorithm because wpa_supplicant
doesn't reset it, and then we fail to use shared
key auth when required later.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:01:53 -04:00
Johannes Berg bc92afd920 cfg80211: implement iwpower
Just on/off and timeout, and with a hacky cfg80211 method
until we figure out what we want, though this is probably
sufficient as we want to use pm_qos for wifi everywhere.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:01:51 -04:00
Johannes Berg f21293549f cfg80211: managed mode wext compatibility
This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 15:01:51 -04:00