This patch increases the mask in the FLEXCAN_MCR_MAXMB() to 7 bits as in the
newer flexcan cores the MAXMB field is 7 bits wide.
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch implements the workaround mentioned in ERR005829:
ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
be transmitted in a specific moment during the arbitration process.
Workaround: The workaround consists of two extra steps after setting up a
message for transmission:
Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.
Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.
This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: Jay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Not all filesystems now provide the rename i_op - ext4 for one - but rather
provide the rename2 i_op. CacheFiles checks that the filesystem has rename
and so will reject ext4 now with EPERM:
CacheFiles: Failed to register: -1
Fix this by checking for rename2 as an alternative. The call to vfs_rename()
actually handles selection of the appropriate function, so we needn't worry
about that.
Turning on debugging shows:
[cachef] ==> cachefiles_get_directory(,,cache)
[cachef] subdir -> ffff88000b22b778 positive
[cachef] <== cachefiles_get_directory() = -1 [check]
where -1 is EPERM.
Signed-off-by: David Howells <dhowells@redhat.com>
These two have been unused since
commit c4d6d8dbf3
CacheFiles: Fix the marking of cached pages
in 3.8.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
In iscsi_copy_param_list() a failed iscsi_param_list memory allocation
currently invokes iscsi_release_param_list() to cleanup, and will promptly
trigger a NULL pointer dereference.
Instead, go ahead and return for the first iscsi_copy_param_list()
failure case.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in iscsit_logout_post_handler_diffcid() where
a pointer used as storage for list_for_each_entry() was incorrectly
being used to determine if no matching entry had been found.
This patch changes iscsit_logout_post_handler_diffcid() to key off
bool conn_found to determine if the function needs to exit early.
Reported-by: Joern Engel <joern@logfs.org>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE for setting
the supported ALUA access states via configfs, originally introduced
in commit b0a382c5.
A value of 1 should enable the support, not disable it.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes an apparent cut and paste error in spc_emulate_evpd_b3(),
where lba_map_segment_size was being used twice for the Referrals VPD.
Go ahead and set the correct user data segment multiplier instead of
user data segment size.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reverts commit 4dfe694f61.
In that, we did:
Here we move the rootdelay code to be right beside the rootwait code, so
that their behaviour is consistent.
...which is fine, but in hindsight, perhaps moving the rootwait to be
beside the rootdelay would have been better. We also indicated:
It should be noted that in doing so, the actions based on the
saved_root_name[0] and initrd_load() were previously put on hold by
rootdelay=N and now currently will not be delayed. However, I think
consistent behaviour is more important than matching historical behaviour
of delaying the above two operations.
But Pavel reported an instance where an ARM target with root on MMC
was failing to mount root, and Russell diagnosed it to the fact that
the call to set ROOT_DEV within the saved_root_name[0] processing
block mentioned above was no longer being delayed.
Rather than moving both wait clauses to the original position of
rootdelay and risking unearthing other possible corner case breakage
at this point in time, we simply revert now and we can revisit
trying the alternate/earlier location in another development cycle.
Cc: Pavel Machek <pavel@denx.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel code overrides the default ISA as passed by the compiler
in quite a few places. This has unfortunate side effects when smartmips
is enabled leading to hundreds of warnings during build such as:
{standard input}: Assembler messages:
{standard input}:411: Warning: the `smartmips' extension requires MIPS32
revision 1 or greater
{standard input}: Assembler messages:
{standard input}:43: Warning: the 64-bit MIPS architecture does not support the
`smartmips' extension
[...]
Until the kernel code is fixed properly (if possible), disable all the
assembler warning messages to make the build logs readable again.
This has no runtime side effects but it makes it easier to spot
more critical warnings and problems during build.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
power1_input should only be reported for Fam15h, Models 00h-0fh
So, introduce a is_visible function to take care of this.
As suggested by Guenter here:
http://marc.info/?l=linux-kernel&m=141038145616437&w=2
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 22e32f4f57 ('x86,AMD: Power driver support for AMD's family 16h processors')
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
avi infoframe is a 13 bytes array, do not read after this limite.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When a ranged fsync finishes if there are still extent maps in the modified
list, still set the inode's logged_trans and last_log_commit. This is important
in case an inode is fsync'ed and unlinked in the same transaction, to ensure its
inode ref gets deleted from the log and the respective dentries in its parent
are deleted too from the log (if the parent directory was fsync'ed in the same
transaction).
Instead make btrfs_inode_in_log() return false if the list of modified extent
maps isn't empty.
This is an incremental on top of the v4 version of the patch:
"Btrfs: fix fsync data loss after a ranged fsync"
which was added to its v5, but didn't make it on time.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Commit 20cde69402 ("x86, ia64: Move EFI_FB vga_default_device()
initialization to pci_vga_fixup()") moved boot video device detection from
efifb to x86 and ia64 pci/fixup.c.
Remove the left-over #ifndef check that will always match since the
corresponding arch-specific define is gone with above patch.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Garrett <matthew.garrett@nebula.com>
There are other kconfig symbols which use SCSI_FC_ATTRS.
In order to maintain sanity and prevent kconfig warnings, change
all of these from using 'select' to using 'depends on' so that
proper symbol dependencies will be honored and circular depends
problems will be avoided.
This fixes kconfig warnings and build errors:
warning: (LIBFC && SCSI_IBMVFC && SCSI_QLA_FC && SCSI_LPFC && ZFCP && SCSI_BFA_FC && SCSI_CHELSIO_FCOE && FUSION_FC) selects SCSI_FC_ATTRS which has unmet direct dependencies (SCSI && NET)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_event':
drivers/scsi/scsi_transport_fc.c:543:7: error: 'scsi_nl_sock' undeclared (first use in this function)
drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_vendor_event':
drivers/scsi/scsi_transport_fc.c:611:7: error: 'scsi_nl_sock' undeclared (first use in this function)
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Nikolay Aleksandrov. In efx_init_port() we call
efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls
efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this
lock is uninitialised, because we haven't called register_netdevice() yet.
So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before
doing anything else.
The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the
corresponding check.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the ACPI based switches the MODULE_DEVICE_TABLE is missing to
export the entries for module auto-loading.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().
Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 20cde69402 ("x86, ia64: Move EFI_FB vga_default_device()
initialization to pci_vga_fixup()") moved boot video device detection from
efifb to x86 and ia64 pci/fixup.c.
For dual-GPU Apple computers above change represents a regression as code
in efifb did forcefully override vga_default_device while the merge did not
(vgaarb happens prior to PCI fixup).
To improve on initial device selection by vgaarb (it cannot know if PCI
device not behind bridges see/decode legacy VGA I/O or not), move the
screen_info based check from pci_video_fixup() to vgaarb's init function and
use it to refine/override decision taken while adding the individual PCI
VGA devices. This way PCI fixup has no reason to adjust vga_default_device
anymore but can depend on its value for flagging shadowed VBIOS.
This has the nice benefit of removing duplicated code but does introduce a
#if defined() block in vgaarb. Not all architectures have screen_info and
would cause compile to fail without it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84461
Reported-and-Tested-By: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
Remove empty function davinci_spi_cleanup().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rob Clark reports a sleeping while atomic bug when using perf.
BUG: sleeping function called from invalid context at ../kernel/locking/mutex.c:583
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
------------[ cut here ]------------
WARNING: CPU: 2 PID: 4828 at ../kernel/locking/mutex.c:479 mutex_lock_nested+0x3a0/0x3e8()
DEBUG_LOCKS_WARN_ON(in_interrupt())
Modules linked in:
CPU: 2 PID: 4828 Comm: Xorg.bin Tainted: G W 3.17.0-rc3-00234-gd535c45-dirty #819
[<c0216690>] (unwind_backtrace) from [<c0212174>] (show_stack+0x10/0x14)
[<c0212174>] (show_stack) from [<c0867cc0>] (dump_stack+0x98/0xb8)
[<c0867cc0>] (dump_stack) from [<c02492a4>] (warn_slowpath_common+0x70/0x8c)
[<c02492a4>] (warn_slowpath_common) from [<c02492f0>] (warn_slowpath_fmt+0x30/0x40)
[<c02492f0>] (warn_slowpath_fmt) from [<c086a3f8>] (mutex_lock_nested+0x3a0/0x3e8)
[<c086a3f8>] (mutex_lock_nested) from [<c0294d08>] (irq_find_host+0x20/0x9c)
[<c0294d08>] (irq_find_host) from [<c0769d50>] (of_irq_get+0x28/0x48)
[<c0769d50>] (of_irq_get) from [<c057d104>] (platform_get_irq+0x1c/0x8c)
[<c057d104>] (platform_get_irq) from [<c021a06c>] (cpu_pmu_enable_percpu_irq+0x14/0x38)
[<c021a06c>] (cpu_pmu_enable_percpu_irq) from [<c02b1634>] (flush_smp_call_function_queue+0x88/0x178)
[<c02b1634>] (flush_smp_call_function_queue) from [<c0214dc0>] (handle_IPI+0x88/0x160)
[<c0214dc0>] (handle_IPI) from [<c0208930>] (gic_handle_irq+0x64/0x68)
[<c0208930>] (gic_handle_irq) from [<c0212d04>] (__irq_svc+0x44/0x5c)
Exception stack(0xe63ddea0 to 0xe63ddee8)
dea0: 00000001 00000001 00000000 c2f3b200 c16db380 c032d4a0 e63ddf40 60010013
dec0: 00000000 001fbfd4 00000100 00000000 00000001 e63ddee8 c0284770 c02a2e30
dee0: 20010013 ffffffff
[<c0212d04>] (__irq_svc) from [<c02a2e30>] (ktime_get_ts64+0x1c8/0x200)
[<c02a2e30>] (ktime_get_ts64) from [<c032d4a0>] (poll_select_set_timeout+0x60/0xa8)
[<c032d4a0>] (poll_select_set_timeout) from [<c032df64>] (SyS_select+0xa8/0x118)
[<c032df64>] (SyS_select) from [<c020e8e0>] (ret_fast_syscall+0x0/0x48)
---[ end trace 0bb583b46342da6f ]---
INFO: lockdep is turned off.
We don't really need to get the platform irq again when we're
enabling or disabling the per-cpu irq. Furthermore, we don't
really need to set and clear bits in the active_irqs bitmask
because that's only used in the non-percpu irq case to figure out
when the last CPU PMU has been disabled. Just pass the irq
directly to the enable/disable functions to clean all this up.
This should be slightly more efficient and also fix the
scheduling while atomic bug.
Fixes: bbd6455937 "ARM: perf: support percpu irqs for the CPU PMU"
Reported-by: Rob Clark <robdclark@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TPIDRURO and TPIDRURW registers need to be flushed during exec;
otherwise TLS information is potentially leaked. TPIDRURO in
particular needs careful treatment. Since flush_thread basically
needs the same code used to set the TLS in arm_syscall, pull that into
a common set_tls helper in tls.h and use it in both places.
Similarly, TEEHBR needs to be cleared during exec as well. Clearing
its save slot in thread_info isn't right as there is no guarantee
that a thread switch will occur before the new program runs. Just
setting the register directly is sufficient.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previous commits that dealt with get_user for 64bit type missed to
export proper functions, so if get_user macro with particular target/value
types are used by kernel module modpost would produce 'undefined!' error.
Solution is to export all required functions.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
on large sparse files, a negative dentry hashing fix, a fix for
flock, and a bug fix relating to d_splice_alias usage. There are
also (patches 1 and 5) a couple of updates which are less
critical, but small and low risk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=5NIi
-----END PGP SIGNATURE-----
Merge tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes
Pull gfs2 fixes from Steven Whitehouse:
"Here are a number of small fixes for GFS2.
There is a fix for FIEMAP on large sparse files, a negative dentry
hashing fix, a fix for flock, and a bug fix relating to d_splice_alias
usage.
There are also (patches 1 and 5) a couple of updates which are less
critical, but small and low risk"
* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: fix d_splice_alias() misuses
GFS2: Don't use MAXQUOTAS value
GFS2: Hash the negative dentry during inode lookup
GFS2: Request demote when a "try" flock fails
GFS2: Change maxlen variables to size_t
GFS2: fs/gfs2/super.c: replace seq_printf by seq_puts
Commit d6bb3e9075 ("vfs: simplify and shrink stack frame of
link_path_walk()") introduced build problems with GCC versions older
than 4.6 due to the initialisation of a member of an anonymous union in
struct qstr without enclosing braces.
This hits GCC bug 10676 [1] (which was fixed in GCC 4.6 by [2]), and
causes the following build error:
fs/namei.c: In function 'link_path_walk':
fs/namei.c:1778: error: unknown field 'hash_len' specified in initializer
This is worked around by adding explicit braces.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
[2] https://gcc.gnu.org/viewcvs/gcc?view=revision&revision=159206
Fixes: d6bb3e9075 (vfs: simplify and shrink stack frame of link_path_walk())
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly driver fixes, the biggest one being the tlv320aic31xx
which is relatively large but simple and device specific. There's a
small fix in the error handling in DPCM too which is relatively minor
error handling fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUF2h1AAoJECTWi3JdVIfQt0UH/155GaSoLBAfnvjBBlmyTTSx
nY/kdZYB9tMR0Y35PuX1Ekd2VNaLFKTEpUsYLLCfvoKezwr0y5Trz5p78g/RoEPH
uU0Z6mQ7/5nepwy3QBnZG3s5TfSxtLA1ifGx0YGn2pY+c1qnhsPRCPTWjQ9lEsQv
f5WfIOMULKCtXT+hHLwzCeKHu1pF6SM6w5Vppys4i+Lu/Ac/7MdD2PzrSR94Y+82
5PftV9HJQil//qFcxQEUUUGPharBu7BsWn8HVqT/oN9FkglZWmHLNIvks+qHmX6/
6GTR7K2FX+2DI4mvRfTz/mb95un1UWzVQByqhhJqt/OohNfZX743ag5bn7M0HUE=
=SME3
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.17
This is mostly driver fixes, the biggest one being the tlv320aic31xx
which is relatively large but simple and device specific. There's a
small fix in the error handling in DPCM too which is relatively minor
error handling fix.
If the mfsymlinks file size has changed (e.g. the file no longer
represents an emulated symlink) we were not returning an error properly.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
cifs provides two dummy functions 'sess_auth_lanman' and
'sess_auth_kerberos' for the case in which the respective
features are not defined. However, the caller is also under
an #ifdef, so we just get warnings about unused code:
fs/cifs/sess.c:1109:1: warning: 'sess_auth_kerberos' defined but not used [-Wunused-function]
sess_auth_kerberos(struct sess_data *sess_data)
Removing the dead functions gets rid of the warnings without
any downsides that I can see.
(Yalin Wang reported the identical problem and fix so added him)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Signed-off-by: Steve French <smfrench@gmail.com>
This reverts commit 52a3624444.
Causes rmmod to fail for at least 7 seconds after unmount which
makes automated testing a little harder when reloading cifs.ko
between test runs.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
CC: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Currently we genarate a queueing route if we have matching policies
but can not resolve the states and the sysctl xfrm_larval_drop is
disabled. Here we assume that dst_output() is called to kill the
queued packets. Unfortunately this assumption is not true in all
cases, so it is possible that these packets leave the system unwanted.
We fix this by generating queueing routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: a0073fe18e ("xfrm: Add a state resolution packet queue")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently we genarate a blackhole route route whenever we have
matching policies but can not resolve the states. Here we assume
that dst_output() is called to kill the balckholed packets.
Unfortunately this assumption is not true in all cases, so
it is possible that these packets leave the system unwanted.
We fix this by generating blackhole routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: 2774c131b1 ("xfrm: Handle blackhole route creation via afinfo.")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Fix build errors when CONFIG_SCSI_NETLINK is enabled but
CONFIG_NET is not enabled:
drivers/built-in.o: In function `scsi_nl_rcv_msg':
scsi_netlink.c:(.text+0x1850fa): undefined reference to `netlink_ack'
scsi_netlink.c:(.text+0x185105): undefined reference to `skb_pull'
scsi_netlink.c:(.text+0x18515d): undefined reference to `netlink_capable'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185244): undefined reference to `init_net'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185258): undefined reference to `__netlink_kernel_create'
drivers/built-in.o: In function `scsi_netlink_exit':
(.text+0x185291): undefined reference to `netlink_kernel_release'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Survived a few days in linux-next.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Byr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"virtio-rng corner case fixes, with cc:stable.
Survived a few days in linux-next"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-rng: skip reading when we start to remove the device
virtio-rng: fix stuck of hot-unplugging busy device
Ensure that the mode reported for the registers file in debugfs is
accurate by marking it as read only when the define to enable writes has
not been set. This is on the edge of being a bug fix but it's debugfs
and it makes it much easier for users to spot what's going wrong when
they forget to enable writeability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUF218AAoJECTWi3JdVIfQDToIAIPpC20A0Tb2+20pxUDO717d
QOpLymMm9qe4Fwbb8wdzM/D3Usy4CG0vrZg8cFX2qZnfKrMPQy9/IQ6kh0SWMvpb
5FQRBd8IkEIMxM9Ng+aAarJIS+xQTdgLDjFIapaBNp0DW5eT0ZaEMYri5Wt2Ut4u
a33GtvXC8Raqbk6A7GpxijVKuApFVz+SH8HB/NqOyNZWXiXcRkZ6bWwgn7YeAqPy
ABg+CAQhjwzXjZSn8Vbt6TNS7jhJzXx5v1wEsx4mcthj2GlBlFexvYDqYBM8VuGJ
GO4F1EHCK/bVRGAgfy1EyeYPqEuedJleap5r8/0T6oFi4VDJ2z6funnt8QwwVDo=
=NVI6
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Fix registers file in debugfs
Ensure that the mode reported for the registers file in debugfs is
accurate by marking it as read only when the define to enable writes
has not been set. This is on the edge of being a bug fix but it's
debugfs and it makes it much easier for users to spot what's going
wrong when they forget to enable writeability"
* tag 'regmap-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix debugfs-file 'registers' mode
Pull input updates from Dmitry Torokhov:
"A few quirks for i8042/AT keyboards and a small device tree doc fix
for Atmel Touchscreens"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix merge in DT documentation
Input: i8042 - also set the firmware id for MUXed ports
Input: i8042 - add nomux quirk for Avatar AVIU-145A6
Input: i8042 - add Fujitsu U574 to no_timeout dmi table
Input: atkbd - do not try 'deactivate' keyboard on any LG laptops
Anish Bhatt says:
====================
net: Fix randconfig errros in bnx2i/bnx2fc caused by IPV6
Just like CNIC bnx2i/bnx2fc also have their tristate dependent on IPV6, however
using the same solution as CNIC can cause recursive dependecies during make.
Based on suggestions by Randy Dunlap, SCSI_NETLINK now depends on NET instead
of selecting NET. Second patch fixes the actual randconfig error.
Entire thread can be followed here : https://lkml.org/lkml/2014/9/9/500
Fixes: c99d667e85 ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like CNIC, tristate of these two modules is also dependent on IPV6.
These need to be handled separately as they select CNIC, which can override
tristate for CNIC from 'm' to 'y', which can cause build failures when ipv6 is
compiled as a module even if CNIC's Kconfig will only 'm' or 'n' when ipv6 is
compiled as a module.
Fixes: c99d667e85 ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Required for avoiding recursive dependencies in the Kconfig, brought out
by fixing randconfig error for bnx2i/bnx2fc in the patch that follows.
As suggested by Randy Dunlap
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde
David Jander
Oliver Hartkopp
Roger Quadros
David Howells
NeilBrown
Milosz Tanski
Joern Engel
Nicholas Bellinger
Sebastian Herbszt
Paul Gortmaker
Markos Chandras
Aravind Gopalakrishnan
Benjamin Gaignard
Mark Brown
Filipe Manana
Bruno Prémont
Randy Dunlap
Edward Cree
Marcel Holtmann
hayeswang
Grygorii Strashko
Stephen Boyd
Nathan Lynch
Victor Kamensky
Linus Torvalds
James Hogan
Takashi Iwai
Steve French
Arnd Bergmann
Steffen Klassert
David S. Miller
Anish Bhatt