Commit Graph

16 Commits

Author SHA1 Message Date
Douglas Anderson d4aa908c79 mmc: dw_mmc: rockchip: Set the drive phase properly
Historically for Rockchip devices we've relied on the power-on
default (or perhaps the firmware setting) to get the correct drive
phase for dw_mmc devices.  This worked OK for the most part, but:

* Relying on the setting just "being right" is a bit fragile.

* As soon as there is an instance where the power on default is wrong or
  where the firmware didn't configure this properly then we'll get a
  mysterious failure.

In commit 7a03fe6f48 ("clk: rockchip: reset init state before mmc card
initialization") we actually started setting this explicitly in the
kernel, but that commit wasn't quite right and also wasn't quite
enough.  See <https://patchwork.kernel.org/patch/9085311/> for some
details.

Let's explicitly set this phase in dw_mmc.

The comments inside this patch try to explain the situation quite
throughly, but the high level overview of this is:

Before this patch on rk3288 devices tested (after revert of the clock
patch described above):
* eMMC: 180 degrees
* SDMMC/SDIO0/SDIO1: 90 degrees

After this patch:
* Use 90 degree phase offset usually.
* Use 180 degree phase offset for MMC_DDR52, SDR104, HS200.

That means we are _changing_ behavior for those devices in this way:

* If we have HS200 eMMC or DDR52 eMMC, we'll run ID mode at 90
  degrees (vs 180) but otherwise have no change.

* For any non-HS200 / non-DDR52 eMMC devices we'll now _always_ run at
  90 degrees (vs 180).  It seems fairly unlikely that building modern
  hardware is using an eMMC that isn't using DDR52 or HS200, of course.

* For SDR104 cards we'll now run with 180 degree phase offset (vs 90).
  It's expected that 90 degree phase offset would have worked OK, but
  this gives us extra margin.

I have tested this by inserting my collection of uSD cards (mostly UHS,
though a few not) into a veyron_minnie and confirmed that they still
seem to enumerate properly.  For a subset of them I tried putting a
filesystem on them and also tried running mmc_test.

Fixes: 7a03fe6f48 ("clk: rockchip: reset init state before mmc card initialization")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-23 11:45:47 +02:00
Shawn Lin d57fe83e07 mmc: dw_mmc-rockchip: add MMC_CAP_CMD23 capabilities
Add MMC_CAP_CMD23 for dw_mmc-rockchip, otherwise
failing to create rpmb partition. With it, we can
get rpmb successfully:

mmc1: new HS200 MMC card at address 0001
mmcblk0: mmc1:0001 DS2016 14.7 GiB
mmcblk0boot0: mmc1:0001 DS2016 partition 1 4.00 MiB
mmcblk0boot1: mmc1:0001 DS2016 partition 2 4.00 MiB
mmcblk0rpmb: mmc1:0001 DS2016 partition 3 4.00 MiB

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-23 11:45:34 +02:00
Shawn Lin 1975676080 mmc: dw_mmc-rockchip: remove setup_clock for rockchip
We remove setup_clock hook and combine it into
init hook to simplify the code

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-02 10:33:17 +02:00
Shawn Lin c6a9bf99dd mmc: dw_mmc-rockchip: fix failing to mount partition with "discard"
Without MMC_CAP_ERASE support, we fail to mount partition
with "discard" option since mmc_queue_setup_discard is limited
for checking mmc_can_erase. Without doing mmc_queue_setup_discard,
blk_queue_discard fails to test QUEUE_FLAG_DISCARD flag, so we get
the following log from f2fs(actually similar to other file system):

mounting with "discard" option, but the device does not support discard

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-02 10:33:15 +02:00
Shawn Lin 31fa83539f mmc: dw_mmc-rockchip: remove dw_mci_rockchip_pmops
dw_mci_rockchip_pmops just copy-paste what dw_mci_pltfm_pmops
have done. Let's remove it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-02 10:33:15 +02:00
Jaehoon Chung aaaaeb7a93 mmc: dw_mmc: remove the prepare_command hook
This patch removes the prepare_command hook from entire dw_mmc driver.
Now, almost all SoCs are using by default, except Exynos.
It seems that dwmmc controller is using unnecessary hook.
To know whether needs to set this bit or not,
add the DW_MMC_CARD_NO_USE_HOLD bit.

If some SoCs need to disable this in future, just set the
DW_MMC_CARD_NO_USE_HOLD bit.
set_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags),

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-02-29 11:03:09 +01:00
Ulf Hansson 7b6471a968 mmc: core: Remove MMC_CAP_RUNTIME_RESUME as it's redundant
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-12-22 11:32:03 +01:00
Chaotian Jing 9979dbe515 mmc: mmc: extend the mmc_send_tuning()
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.

in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-10-27 10:38:41 +01:00
Alexandru M Stan cbb79e43c8 mmc: dw_mmc-rockchip: MMC tuning with the clock phase framework
This algorithm will try 1 degree increments, since there's no way to tell
what resolution the underlying phase code uses. As an added bonus, doing
many tunings yields better results since some tests are run more than once
(ex: if the underlying driver uses 45 degree increments, the tuning code
will try the same angle more than once).

It will then construct a list of good phase ranges (even ranges that cross
360/0), will pick the biggest range then it will set the sample_clk to the
middle of that range.

We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time (ex 10
degrees) this will not work with the current clock phase framework (which
floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.

If a device has device specific code (like exynos) then that will still
take precedence, otherwise this new code will execute. If the device wants
to tune, but has no sample_clk defined we'll return EIO with an error
message.

Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-10-26 16:00:12 +01:00
Addy Ke 57e104864b mmc: dw_mmc: add quirk for broken data transfer over scheme
This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.

dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.

We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.

This means that host should get DRTO and DTO interrupt.

But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.

There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.

Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-08-17 12:45:28 +02:00
Zhangfei Gao a7ca2b1643 mmc: dw_mmc: rockchip: Fix modalias to make module auto-loading work
Make the modalias match driver name, this is required to make module
auto-loading work.

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
CC: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:06 +02:00
addy ke 6d53200b51 mmc: dw_mmc: rockchip: add support MMC_CAP_RUNTIME_RESUME capability
To support HS200 and UHS mode, mmc core will call init_card() to
execute tuning:
- sdio: init_card can be executed at runtime resume.
- sd and mmc: init_card can be executed at resume or runtime resume,
  which depends on MMC_CAP_RUNTIME_RESUME capability.

On rk3288 SoC, host will get DRTO interrupt when host send command
to read tuning data. This will spend more than 111ms:
drto_ms = drto_clks * 1000 / bus_hz = 111ms.

And the total tuning time will be more than 400ms.

So we should add MMC_CAP_RUNTIME_RESUME capability to execute tuning
at runtime resume. Only if we do so, can we pass resume test.

Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-03-23 14:13:28 +01:00
Dmitry Torokhov 9608337945 mmc: dw_mmc: rockchip: remove incorrect __exit_p()
dw_mci_pltfm_remove() is not (nor should it be) marked as __exit,
so we should not be using __exit_p() wrapper with it.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-28 12:32:20 +01:00
Addy Ke 767562348b mmc: dw_mmc: add support for the other bit of sdio interrupt
The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.

Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:00 +01:00
Doug Anderson e7791079ae mmc: dw_mmc: rockchip: Don't recalc the clock when it goes off
The "set_ios" function is called with a clock of 0 when the clock is
turning off.  There's no reason to go through all the extra Rockchip
logic (whose goal is to make sure DIV is 0 or 1) in that case.  The
Rockchip logic happened to work because the CCF will pick the lowest
possible rate when you ask it for a clock of 0, but it's silly to go
through all the remuxing and adjusting for no reason.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-10 12:40:36 +01:00
addy ke 4cdc2ec1da mmc: dw_mmc: move rockchip related code to a separate file
To support HS200 and UHS-1, we need add a big hunk of code,
as shown in the following patches. So a separate file for
rockchip SOCs is suitable.

Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:16 +02:00