Initially I had to write to both the MASK and ENABLE registers, otherwise
the CPLD would generate tons of spurious interrupts. With the change to
the demux handler to disable the muxed line, it is now sufficient to
disable the interrupt by writing either the enable or mask register.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move add_wired_entry to its own header file from where it will be
always included. Patch up other users of add_wired_entry to also include
the header as needed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move PCI Controller PM to syscore_ops since the platform_driver PM methods
are called way too late on resume and far too early on suspend (after and
before PCI device resume/suspend).
This also allows to simplify wired entry management a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix loss of notification with multi-event
perf, x86: Force IBS LVT offset assignment for family 10h
perf, x86: Disable PEBS on SandyBridge chips
trace_events_filter: Use rcu_assign_pointer() when setting ftrace_event_call->filter
perf session: Fix crash with invalid CPU list
perf python: Fix undefined symbol problem
perf/x86: Enable raw event access to Intel offcore events
perf: Don't use -ENOSPC for out of PMU resources
perf: Do not set task_ctx pointer in cpuctx if there are no events in the context
perf/x86: Fix PEBS instruction unwind
oprofile, x86: Fix crash when unloading module (nmi timer mode)
oprofile: Fix crash when unloading module (hr timer mode)
mips copied pci_iomap from generic code, probably to avoid
pulling the rest of iomap.c in. Since that's in
a separate file now, we can reuse the common implementation.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: lantiq: use export.h in favour of module.h
MAINTAINERS: The MIPS git tree has moved.
MIPS: Fix build error due to missing inclusion of <linux/export.h>.
MIPS: ASID conflict after CPU hotplug
MIPS: Octeon: Fix compile error in arch/mips/cavium-octeon/flash_setup.c
MIPS: errloongson2_clock: Fix build error by including linux/module.h
STAGING: octeon-ethernet: Fix compile error caused by skb_frag_struct change
MIPS: Hook up process_vm_readv and process_vm_writev system calls.
MIPS: Kernel hangs occasionally during boot.
MIPS: Octeon: Mark SMP-IPI interrupt as IRQF_NO_THREAD
MIPS: BCM47xx: fix build with GENERIC_GPIO configuration
MIPS: NXP: Remove unused source files.
MIPS: Yosemite, Emma: Fix off-by-two in arcs_cmdline buffer size check
The code located at arch/mips/lantiq/ included module.h to be able to use
the EXPORT_SYMBOL* macros. These can now be directly included using
export.h.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
People (Linus) objected to using -ENOSPC to signal not having enough
resources on the PMU to satisfy the request. Use -EINVAL.
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-xv8geaz2zpbjhlx0svmpp28n@git.kernel.org
[ merged to newer kernel, fixed up MIPS impact ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SIBYTE_CFE got killed in commit 05f94eebd5 ("MIPS: Sibyte: Remove
standalone kernel support"). This means that since v2.6.31 there is no
Kconfig symbol SIBYTE_CFE. The select statement for that symbol is a
nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no Kconfig symbol named GCD. The three select statements for
that symbol are nops. Drop these.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I am running SMP Linux 2.6.37-rc1 on BMIPS5000 (single core dual thread)
and observe some abnormalities when doing system suspend/resume which I
narrowed down to cpu hotplugging. The suspend brings the second thread
processor down and then restarts it, after which I see memory corruption
in userspace. I started digging and found out that problem occurs because
while doing execve() the child process is getting the same ASID as the
parent, which obviously corrupts parent's address space.
Further digging showed that activate_mm() calls get_new_mmu_context() to
get a new ASID, but at this time ASID field in entryHi is 1, and
asid_cache(cpu) is 0x100 (it was just reset to ASID_FIRST_VERSION when
the secondary TP was booting).
So, get_new_mmu_context() increments the asid_cache(cpu) value to
0x101, and thus puts 0x01 into entryHi. The result - ASID field does
not get changed as it was supposed to.
My solution is very simple - do not reset asid_cache(cpu) on TP warm
restart.
Patchwork: https://patchwork.linux-mips.org/patch/1797/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The parse_mtd_partitions() and mtd_device_register() functions were
combined into mtd_device_parse_register(). So call that instead.
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the following compilation failure with v3.2-rc1 by including module.h:
CC [M] arch/mips/kernel/cpufreq/loongson2_clock.o
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:168:15: error: expected declaration specifiers or '...' before string constant
arch/mips/kernel/cpufreq/loongson2_clock.c:169:20: error: expected declaration specifiers or '...' before string constant
arch/mips/kernel/cpufreq/loongson2_clock.c:170:16: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2922/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 802.1X EAPOL handshake hostapd does requires
knowing whether the frame was ack'ed by the peer.
Currently, we fudge this pretty badly by not even
transmitting the frame as a normal data frame but
injecting it with radiotap and getting the status
out of radiotap monitor as well. This is rather
complex, confuses users (mon.wlan0 presence) and
doesn't work with all hardware.
To get rid of that hack, introduce a real wifi TX
status option for data frame transmissions.
This works similar to the existing TX timestamping
in that it reflects the SKB back to the socket's
error queue with a SCM_WIFI_STATUS cmsg that has
an int indicating ACK status (0/1).
Since it is possible that at some point we will
want to have TX timestamping and wifi status in a
single errqueue SKB (there's little point in not
doing that), redefine SO_EE_ORIGIN_TIMESTAMPING
to SO_EE_ORIGIN_TXSTATUS which can collect more
than just the timestamp; keep the old constant
as an alias of course. Currently the internal APIs
don't make that possible, but it wouldn't be hard
to split them up in a way that makes it possible.
Thanks to Neil Horman for helping me figure out
the functions that add the control messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 5f7efb4 (Kbuild: append missing-syscalls to the default target
list) broke MIPS build.
Reported-tested-and-acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The Kernel hangs occasionally during boot after "Calibrating delay loop..".
This is caused by the c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable the timer and hang later.
The false return happens because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits for the timer changes to
propagate to the cp0 cause register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb instructions and can take
as little as a few clock ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not working. This fix uses up
to a max number of cycle counter ticks for the delay and uses
back_to_back_c0_hazard() instead of irq_disable_hazard() to handle the
hazard condition between cp0 writes and cp0 reads.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to exclude it from force threading to allow RT patch set to work.
And while on this line
* Remove IRQF_DISABLED as as this flag is NOOP
* Add IRQF_PERCPU as this is a per cpu interrupt.
Signed-off-by: Venkat Subbiah <venkat.subbiah@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
To: linux-rt-users@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2817/
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since eb9ae7f2 (gpio: fix build error in include/asm-generic/gpio.h)
the generic version of gpio.h calls __gpio_{set,get}_value which we
do not define. Get rid of asm-generic/gpio.h and define the missing
stubs directly for BCM47xx to build.
Reported-by: Ralf Baechle <ralf@linux-mips.org>
To: linux-mips@linux-mips.org
CC: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2885/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cause is a misplaced bracket.
The code
strlen(buf+1)
will be two bytes less than
strlen(buf)+1
The +1 is in this code to reserve space for an additional space character.
[ralf@linux-mips.org: Thomas' original patch fixed the issue only for
Yosemite but the same bug exists also in Emma.]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Patchwork: https://patchwork.linux-mips.org/patch/2861/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scsi: drop unused Kconfig symbol
pci: drop unused Kconfig symbol
stmmac: drop unused Kconfig symbol
x86: drop unused Kconfig symbol
powerpc: drop unused Kconfig symbols
powerpc: 40x: drop unused Kconfig symbol
mips: drop unused Kconfig symbols
openrisc: drop unused Kconfig symbols
arm: at91: drop unused Kconfig symbol
samples: drop unused Kconfig symbol
m32r: drop unused Kconfig symbol
score: drop unused Kconfig symbols
sh: drop unused Kconfig symbol
um: drop unused Kconfig symbol
sparc: drop unused Kconfig symbol
alpha: drop unused Kconfig symbol
Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig
as per Michal: the STMMAC_DUAL_MAC config variable is still unused and
should be deleted.
* 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linux: (47 commits)
i2c-s3c2410: Add device tree support
i2c-s3c2410: Keep a copy of platform data and use it
i2c-nomadik: cosmetic coding style corrections
i2c-au1550: dev_pm_ops conversion
i2c-au1550: increase timeout waiting for master done
i2c-au1550: remove unused ack_timeout
i2c-au1550: remove usage of volatile keyword
i2c-tegra: __iomem annotation fix
i2c-eg20t: Add initialize processing in case i2c-error occurs
i2c-eg20t: Fix flag setting issue
i2c-eg20t: add stop sequence in case wait-event timeout occurs
i2c-eg20t: Separate error processing
i2c-eg20t: Fix 10bit access issue
i2c-eg20t: Modify returned value s32 to long
i2c-eg20t: Fix bus-idle waiting issue
i2c-designware: Fix PCI core warning on suspend/resume
i2c-designware: Add runtime power management support
i2c-designware: Add support for Designware core behind PCI devices.
i2c-designware: Push all register reads/writes into the core code.
i2c-designware: Support multiple cores using same ISR
...
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
None of these files are using modular infrastructure, and build
tests reveal that none of these files are really relying on any
implicit inclusions via. module.h either. So delete them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files are not modules, but were including module.h only for
EXPORT_SYMBOL and/or THIS_MODULE. Now that we have the lightweight
export.h, use it in these kinds of cases.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We need to call out inclusion of smp.h, or with the module.h cleanup
we'll get things like:
arch/mips/loongson/common/platform.c:21: error: implicit declaration of function 'smp_processor_id'
arch/mips/vr41xx/common/giu.c:84: error: implicit declaration of function 'smp_processor_id'
arch/mips/vr41xx/common/rtc.c:85: error: implicit declaration of function 'smp_processor_id'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We are relying on asm/elf.h being present implicitly. Once we clean
up the root cause of that, we'll see this, so fix it in advance.
arch/mips/kernel/cpu-probe.c: In function 'set_elf_platform':
arch/mips/kernel/cpu-probe.c:298: error: '__elf_platform' undeclared (first use in this function)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These Kconfig entries have been commented out since (at least)
v2.6.12-rc2 (the first commit of the git repository). There's no
indication why they're commented out. They might as well be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace the usage of "volatile"s with register accessor functions.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue: (21 commits)
leases: fix write-open/read-lease race
nfs: drop unnecessary locking in llseek
ext4: replace cut'n'pasted llseek code with generic_file_llseek_size
vfs: add generic_file_llseek_size
vfs: do (nearly) lockless generic_file_llseek
direct-io: merge direct_io_walker into __blockdev_direct_IO
direct-io: inline the complete submission path
direct-io: separate map_bh from dio
direct-io: use a slab cache for struct dio
direct-io: rearrange fields in dio/dio_submit to avoid holes
direct-io: fix a wrong comment
direct-io: separate fields only used in the submission path from struct dio
vfs: fix spinning prevention in prune_icache_sb
vfs: add a comment to inode_permission()
vfs: pass all mask flags check_acl and posix_acl_permission
vfs: add hex format for MAY_* flag values
vfs: indicate that the permission functions take all the MAY_* flags
compat: sync compat_stats with statfs.
vfs: add "device" tag to /proc/self/mountstats
cleanup: vfs: small comment fix for block_invalidatepage
...
Fix up trivial conflict in fs/gfs2/file.c (llseek changes)
This was found by inspection while tracking a similar
bug in compat_statfs64, that has been fixed in mainline
since decemeber.
- This fixes a bug where not all of the f_spare fields
were cleared on mips and s390.
- Add the f_flags field to struct compat_statfs
- Copy f_flags to userspace in case someone cares.
- Use __clear_user to copy the f_spare field to userspace
to ensure that all of the elements of f_spare are cleared.
On some architectures f_spare is has 5 ints and on some
architectures f_spare only has 4 ints. Which makes
the previous technique of clearing each int individually
broken.
I don't expect anyone actually uses the old statfs system
call anymore but if they do let them benefit from having
the compat and the native version working the same.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
Later IRIX versions provide them in <sys/regdef.h> and gas also accepts
$ta0 .. $ta3 since binutils 2.18 so Linux should do the same for source
compatibility.
The hard coded constants are moved to struct mips_pmu. All counter
register access move to the read_counter and write_counter function
pointers, which are set to either 32-bit or 64-bit access methods at
initialization time.
Many of the function pointers in struct mips_pmu were not needed as
there was only a single implementation, these were removed.
I couldn't figure out what made struct cpu_hw_events.msbs[] at all
useful, so I removed it too.
Some functions and other declarations were reordered to reduce the
need for forward declarations.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The contents of arch/mips/kernel/perf_event.c and
arch/mips/kernel/perf_event_mipsxx.c were divided in a seemingly ad
hoc manner, with the first including the second.
I moved all the hardware counter support code to perf_event_mipsxx.c
and removed the gating #ifdefs to the Kconfig and Makefile.
Now perf_event.c contains only the callchain support, everything else
is in perf_event_mipsxx.c
There are no code changes, only moving of functions from one file to
the other, or removing empty unneeded functions.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dezhong Diao <dediao@cisco.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2791/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Get rid of a bunch of useless inline declarations, and join a bunch of
improperly split lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2793/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It seems that BSP could be setup twice, but the nlm_cpu_ready array is only
set for ASPs in smpboot.S, not including BSP.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Cc: "Jayachandran C." <jayachandranc@netlogicmicro.com>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2695/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>,
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch gets rid of all CONFIG_SOC_AU1XXX defines in
DMA/DBDMA-related code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1xxx-ide uses defines from the pb1200/db1200 headers:
get DBDMA ID through platform resource information,
hardcode register spacing. The only 2 users of this driver (and
the only boards it can really work on realiably) use the same
register layout.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-ide@vger.kernel.org
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-ide@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/2716/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove all redundant peripheral base address defines, fix
all affected boards and drivers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use runtime CPU detection to setup all USB parts.
Remove the Au1200 OTG and UDC platform devices since there are no
drivers for them anyway.
Clean up the USB address mess in the au1000 header.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Alchemy chips have one or more registers which control access
to the usb blocks as well as PHY configuration. I don't want
the OHCI/EHCI glues to know about the different registers and bits;
new code hides the gory details of USB configuration from them.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/2709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/usb/host/alchemy-common.c
For Alchemy-PCI I need to add a wired entry after resuming from RAM;
remove the __init from add_wired_entry() so that this actually works.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For GPIOLIB=y decide at runtime which gpiochips to register;
in the GPIOLIB=n case, the gpio headers need to be reshuffled
a bit to make multiple implementations coexist peacefully.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2679/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No reason NOT to build it
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the last hardcoded base address from the au1000_eth
driver. The base address of the MACDMA unit was derived from the
platform device id; if someone registered the MACs in inverse order
both would not work.
So instead pass the base address of the DMA unit to the driver with
the other platform resource information.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: David S. Miller <davem@davemloft.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2674/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When trying to compile the 3.1-rc10 kernel for my MIPS board with C=1
(sparse checking), the build fails early with the error:
CHK include/linux/version.h
UPD include/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
Checking missing-syscalls for N32
CALL scripts/checksyscalls.sh
Checking missing-syscalls for O32
CALL scripts/checksyscalls.sh
CC kernel/bounds.s
GEN include/generated/bounds.h
CC arch/mips/kernel/asm-offsets.s
GEN include/generated/asm-offsets.h
CALL scripts/checksyscalls.sh
HOSTCC scripts/genksyms/genksyms.o
SHIPPED scripts/genksyms/lex.lex.c
SHIPPED scripts/genksyms/keywords.hash.c
SHIPPED scripts/genksyms/parse.tab.h
HOSTCC scripts/genksyms/lex.lex.o
SHIPPED scripts/genksyms/parse.tab.c
HOSTCC scripts/genksyms/parse.tab.o
HOSTLD scripts/genksyms/genksyms
/bin/sh: Syntax error: "(" unexpected
make[3]: *** [scripts/mod/empty.o] Error 2
make[2]: *** [scripts/mod] Error 2
make[1]: *** [scripts] Error 2
It seems the shell chokes because sparse is called with command line
arguments such as:
-D__INT8_C(c)='c'
Converting these to form:
-D'__INT8_C(c)'='c'
seems to fix the problem.
[ralf@linux-mips.org: This affects builds with gcc 4.5 and newer.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2827/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After the recent cleanup of the register_*_smp_ops() functions msp71xx
wasn't fixed to include the now necessary header resulting in:
/home/ralf/src/linux/upstream-linus/arch/mips/pmc-sierra/msp71xx/msp_setup.c: In function ‘prom_init’:
/home/ralf/src/linux/upstream-linus/arch/mips/pmc-sierra/msp71xx/msp_setup.c:231:2: error: implicit declaration of function ‘register_vsmp_smp_ops’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use -march=xlr if available, otherwise fallback to mips64. This allows
us to support compilation with MIPS toolchains which are not customized
for XLR.
[ralf@linux-mips.org: And more importantly it works around a gas bug in
binutils 2.21 which otherwise may result in an assertion failure building
arch/mips/kernel/genex.S. See
http://sourceware.org/bugzilla/show_bug.cgi?id=12915 for details.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2534/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 97475f8b42e83be2966aa2d70ab9c98477701c53 (lmo) /
82b89152f0 (kernel.org) [MIPS: LD/SD o32
macro GAS fix update].
Turns out this patch is producing many build errors with gcc 4.2. Based
on further testing with a test case extracted from the build errors found
further build errors and suboptimal generation even in violation of the
"R" constraint.
To make matters worse, the binutils changes also don't work quite as
intended so revert this patch for now.
If Open Firmware / Device Tree support is enabled on a SNI RM kernel both
<asm/mipsprom.h> and <asm/prom.h> will be included into some .c files.
Since both headers use the same wrapper symbol only the inclusion of the
first file will have an effect but the 2nd file will be ignored resulting
in a build error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Triggered by pnx8550-jbs_defconfig and pnx8550-stb810_defconfig:
WARNING: vmlinux.o(.text+0xc0c): Section mismatch in reference from the function prom_getcmdline() to the variable .init.data:arcs_cmdline
The function prom_getcmdline() references
the variable __initdata arcs_cmdline.
This is often because prom_getcmdline lacks a __initdata
annotation or the annotation of arcs_cmdline is wrong.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The number of arguments only matters for syscalls with stack arguments that
is using 5 or more argument slots so this is just cosmetic fix.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: vmlinux.o(.text+0x3059f8): Section mismatch in reference from the function pcibios_plat_dev_init() to the function .devinit.text:request_bridge_irq()
The function pcibios_plat_dev_init() references
the function __devinit request_bridge_irq().
This is often because pcibios_plat_dev_init lacks a __devinit
annotation or the annotation of request_bridge_irq is wrong.
Fixing this one leads to:
WARNING: vmlinux.o(.text+0x1790): Section mismatch in reference from the function request_bridge_irq() to the function .devinit.text:register_bridge_irq()
The function request_bridge_irq() references
the function __devinit register_bridge_irq().
This is often because request_bridge_irq lacks a __devinit
annotation or the annotation of register_bridge_irq is wrong.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Until now flush_kernel_vmap_range() and invalidate_kernel_vmap_range() did
not exist on MIPS resulting in heavy cache corruption on XFS filesystems.
Left for the post-3.0 time: optimization and make this work with highmem,
too. Since the combination of highmem + cache aliases atm doesn't work
this isn't a regression.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2505/
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Octeon2 processor cores have a UserLocal register. Remove the hard
coded negative probe and allow the standard probing to detect this
feature.
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2578/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the case PM_DEFAULT_MASK == 0, we were placing a branch in the
delay slot of another branch. This leads to undefined behavior.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2775/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/2753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current Octeon systems do in fact have holes in their memory zones.
We need to select HOLES_IN_ZONE. If we do not, some memory
configurations will result in crashes at boot time like this:
.
.
.
CPU 6 Unable to handle kernel paging request at virtual address 0000000000700000, epc == ffffffff8118fe00, ra == ffffffff8118fe9c
Oops[#1]:
Cpu 6
.
.
.
...
Call Trace:
[<ffffffff8118fe00>] setup_per_zone_wmarks+0x1b0/0x338
[<ffffffff815cd738>] init_per_zone_wmark_min+0x64/0xd0
[<ffffffff81100438>] do_one_initcall+0x38/0x160
.
.
.
Reported-by: Jason Kwon <jason.kwon@ericsson.com>
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Cc: Jason Kwon <jason.kwon@ericsson.com>
Patchwork: https://patchwork.linux-mips.org/patch/2724/
Tested-by: Guenter Roeck<guenter.roeck@ericsson.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert some MIPS architecture's code to using struct syscore_ops
objects for power management instead of sysdev classes and sysdevs.
This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-and-tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-kernel@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Patchwork: http://patchwork.linux-mips.org/patch/2431/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can't trust userspace to pass signed-extend arguments. Not correctly
sign-extended arguments to futex-wait result in architecturally undefined
operation of 32-bit arithmetic instructions.
For example, if 'val' is too big and bit-31 is 1, the caller may enter
endless loop at:
futex_wait_setup()
{
...
if (uval != val) {
queue_unlock(q, *hb);
ret = -EWOULDBLOCK;
...
}
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2714/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Usage of these flags has been deprecated for nearly 4 years by:
commit f77bf01425
Author: Sam Ravnborg <sam@neptun.(none)>
Date: Mon Oct 15 22:25:06 2007 +0200
kbuild: introduce ccflags-y, asflags-y and ldflags-y
Moreover, these flags (at least EXTRA_CFLAGS) have been documented for command
line use. By default, gmake(1) do not override command line setting, so this is
likely to result in build failure or unexpected behavior.
Replace their usage by Kbuild's `{as,cc,ld}flags-y'.
To: linux-kernel@vger.kernel.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/2710/
Cc: linux-mips@linux-mips.org
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Disable the cascade IRQ in the cascade handler. This is required to
get the DB1300 working, and also gets rid of all spurious interrupts
previously observed on the DB1200; so Config[OD] can be disabled
again for better performance.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The bits used to set the PCI bus speed on AR9 are slightly different to
those used on Danube.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2614/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq base offset needs to be ignored when matching irqs to external
interrupt pins. Taking the offset into account resulted in the EIU not
being brought up properly.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2616/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only some GCC versions such as gcc 4.2 notice that the variable wr in
build_r3000_tlb_modify_handler is used uninitialized. When using one
of those GCCs the build will fail due to -Werror. GCC 4.6 does not
warn about the uninitialized use of wr.
This issue was introduced by 7211f4d7a3dcbe57c5d396c334dca525315dceb2
[MIPS: Close races in TLB modify handlers.]
Reported-by: Ganesan Ramalingam <ganesan18@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code forgets the Au1100 when looking for the correct method to
suspend the chip.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Harmless typo which prints an error message although MAC0 was registered
successfully.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/pmc-sierra/msp71xx/msp_irq.o
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:112:2: error: request for member ‘flags’ in something not a structure or union
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:118:2: error: request for member ‘flags’ in something not a structure or union
make[4]: *** [arch/mips/pmc-sierra/msp71xx/msp_irq.o] Error 1
caused by 57336bc1056798d89714b7fb1b1d197e6bda6819 [MIPS: Mark cascade and
low level interrupts IRQF_NO_THREAD].
Commas to separate struct initializers generally are considered useful to
enhance the compilation experience of the user.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
do_signal() does __put_user() which can fault, resulting in a might_sleep()
warning in down_read(&mm->mmap_sem) and a "scheduling while atomic" warning
when mmap_sem is contented. On Swarm this also results in:
WARNING: at kernel/smp.c:459 smp_call_function_many+0x148/0x398()
Modules linked in:
Call Trace:
[<ffffffff804b48a4>] dump_stack+0x1c/0x50
[<ffffffff8013dc94>] warn_slowpath_common+0x8c/0xc8
[<ffffffff8013dcfc>] warn_slowpath_null+0x2c/0x40
[<ffffffff801864a0>] smp_call_function_many+0x148/0x398
[<ffffffff80186748>] smp_call_function+0x58/0xa8
[<ffffffff80119b5c>] r4k_flush_data_cache_page+0x54/0xd8
[<ffffffff801f39bc>] handle_pte_fault+0xa9c/0xad0
[<ffffffff801f40d0>] handle_mm_fault+0x158/0x200
[<ffffffff80115548>] do_page_fault+0x218/0x3b0
[<ffffffff80102744>] ret_from_exception+0x0/0x10
[<ffffffff8010eb18>] copy_siginfo_to_user32+0x50/0x298
[<ffffffff8010edf0>] setup_rt_frame_32+0x90/0x250
[<ffffffff80106414>] do_notify_resume+0x154/0x358
[<ffffffff80102930>] work_notifysig+0xc/0x14
Fixed by enabling interrupts in do_notify_resume before delivering signals.
[ralf@linux-mips.org: Reported and original fix by tglx but I wanted to
minimize the amount of code being run with interrupts disabled so I moved
the local_irq_disable() call right into do_notify_resume. Which is saner
than doing it in entry.S.]
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All low level interrupts have been marked NO_THREAD, so MIPS can enjoy
the wonderful world of forced threaded interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are two cascade interrupts in Loongson machines, one for bonito
northbridge, another for the 8259A controller in the southbridge. Both
want to be non threaded.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/2638/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On preempt-rt this lock needs to be raw, so it does not get converted
to a sleeping spinlock. Trying to sleep in a panic is not really
desireable.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2636/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/kernel/ftrace.c: In function ‘ftrace_get_parent_ra_addr’:
arch/mips/kernel/ftrace.c:212: error: implicit declaration of function ‘in_kernel_space’
arch/mips/kernel/ftrace.c: In function ‘prepare_ftrace_return’:
arch/mips/kernel/ftrace.c:314: error: ‘MCOUNT_OFFSET_INSNS’ undeclared (first use in this function)
arch/mips/kernel/ftrace.c:314: error: (Each undeclared identifier is reported only once
arch/mips/kernel/ftrace.c:314: error: for each function it appears in.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2634/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pci/pci-rc32434.c: In function 'rc32434_pci_init':
arch/mips/pci/pci-rc32434.c:217:16: error: 'rcrc32434_res_pci_io1' undeclared (first use in this function)
arch/mips/pci/pci-rc32434.c:217:16: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-rc32434.o] Error 1
This problem is included in the following commit.
commit 28f65c11f2
Author: Joe Perches <joe@perches.com>
Date: Thu Jun 9 09:13:32 2011 -0700
treewide: Convert uses of struct resource to resource_size(ptr)
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: Joe Perches <joe@perches.com>
Patchwork: https://patchwork.linux-mips.org/patch/2654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in arch/mips/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
To: LKML <linux-kernel@vger.kernel.org>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2540/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The comment for the slave PIC is changed from 8259A-1 to 8259A-2.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
To: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2693/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we could find tc on the tc list for @index, the found tc should be returned.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
To: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2692/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Synopsys DesignWare UART in pmc-sierra msp71xx has an extra feature
where the UART detects a write attempt to the LCR whilst busy and raises
an interrupt. The driver needs to clear the interrupt and rewrite the
LCR. Move this into platform code and out of the 8250 driver.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of the "soc-audio" platform device is no longer en vogue,
update the code to the newer, simpler way of doing things.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PSC audio drivers (psc-ac97/psc-i2s) register the DMA platform_device
on their own. This is frowned upon, from now on board code must
register a simple pcm dma platform device for each PSC with sound duties.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver suitable for the AC97 part on the DB1000/DB1500/DB1100
boards.
Run-tested on DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:
linux/atomic.h
-> asm/atomic.h
-> asm-generic/atomic-long.h
where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype. This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.
Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).
Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Page table entries are made invalid by writing a zero into the the PTE
slot in a page table. This creates a race condition with the TLB
modify handlers when they are updating the PTE.
CPU0 CPU1
Test for _PAGE_PRESENT
. set to not _PAGE_PRESENT (zero)
Set to _PAGE_VALID
So now the page not present value (zero) is suddenly valid and user
space programs have access to physical page zero.
We close the race by putting the test for _PAGE_PRESENT and setting of
_PAGE_VALID into an atomic LL/SC section. This requires more registers
than just K0 and K1 in the handlers, so we need to save some registers
to a save area and then restore them when we are done.
The save area is an array of cacheline aligned structures that should
not suffer cache line bouncing as they are CPU private.
[ralf@linux-mips.org: Fix !defined(CONFIG_MIPS_PGD_C0_CONTEXT) build error.]
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2577/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This can be used from either 32-bit or 64-bit code to generate logical
right shifts of any constant amount.
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Enable cpu_has_clo_clz only when CONFIG_CPU_MIPS32 or CONFIG_CPU_MIPS64
is selected. This will optimize fls() and __fls() to use CLZ insn, and
eventually ffs() and __ffs() as well.
Malta and MIPSSim are development platforms, and need to take care of
various processor configurations, release rivisions and so on, even
across different MIPS ISAs. For such platforms we have to be careful,
for instance, with turning on cpu_has_mips{32,64}r[12] features.
As for CLZ, all MIPS32/64 processors support it, regardless of release
revisions.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
To: David VomLehn <dvomlehn@cisco.com>
To: macro@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1453/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This will optimize fls() and __fls() to use CLZ throughout the kernel,
and any other optimizations that depend on constant cpu_has_* values
will also be used.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
To: David VomLehn <dvomlehn@cisco.com>
To: macro@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1452/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
fixrange_init() allocates page tables for all addresses higher than
FIXADDR_TOP. On processors that override the default FIXADDR_TOP
address of 0xfffe_0000, this can consume up to 4 pages (1 page per 4MB)
for pgd's that are never used.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1980/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Memory maps and addressing quirks are normally defined in <spaces.h>.
There are already three targets that need to override FIXADDR_TOP, and
others exist. This will be a cleaner approach than adding lots of
ifdefs in fixmap.h .
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1573/
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On processors with deep write buffers, it is likely that many cycles
will pass between a CACHE instruction and the time the data actually
gets written out to DRAM. Add a SYNC instruction to ensure that the
buffers get emptied before the flush functions return.
Actual problem seen in the wild:
1) dma_alloc_coherent() allocates cached memory
2) memset() is called to clear the new pages
3) dma_cache_wback_inv() is called to flush the zero data out to memory
4) dma_alloc_coherent() returns an uncached (kseg1) pointer to the
freshly allocated pages
5) Caller writes data through the kseg1 pointer
6) Buffered writeback data finally gets flushed out to DRAM
7) Part of caller's data is inexplicably zeroed out
This patch adds SYNC between steps 3 and 4, which fixed the problem.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pfn_valid() compares the PFN to max_mapnr:
__pfn >= min_low_pfn && __pfn < max_mapnr;
On HIGHMEM kernels, highend_pfn is used to set the value of max_mapnr.
Unfortunately, highend_pfn is left at zero if the system does not
actually have enough RAM to reach into the HIGHMEM range. This causes
pfn_valid() to always return false, and when debug checks are enabled
the kernel will fail catastrophically:
Memory: 22432k/32768k available (2249k kernel code, 10336k reserved, 653k data, 1352k init, 0k highmem)
NR_IRQS:128
kfree_debugcheck: out of range ptr 81c02900h.
Kernel bug detected[#1]:
Cpu 0
$ 0 : 00000000 10008400 00000034 00000000
$ 4 : 8003e160 802a0000 8003e160 00000000
$ 8 : 00000000 0000003e 00000747 00000747
...
On such a configuration, max_low_pfn should be used to set max_mapnr.
This was seen on 2.6.34.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
To: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1992/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduced topdown mmap support in user process address
space allocation policy.
Recently, we ran some large applications that use mmap heavily and
lead to OOM due to inflexible mmap allocation policy on MIPS32.
Since most other major archs supported it for years, it is reasonable
to follow the trend and reduce the pain of porting applications.
Due to cache aliasing concern, arch_get_unmapped_area_topdown() and
other helper functions are implemented in arch/mips/kernel/syscall.c.
Signed-off-by: Jian Peng <jipeng2005@gmail.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2389/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The address limit is already set in flush_old_exec() via set_fs(USER_DS)
so this assignment is redundant.
[ralf@linux-mips.org: also see dac853ae89 for
further explanation.]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2466/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio has been so far used only in the context of virtualization,
and the virtio Kconfig was sourced directly by the relevant arch
Kconfigs when VIRTUALIZATION was selected.
Now that we start using virtio for inter-processor communications,
we need to source the virtio Kconfig outside of the virtualization
scope too.
Moreover, some architectures might use virtio for both virtualization
and inter-processor communications, so directly sourcing virtio
might yield unexpected results due to conflicting selections.
The simple solution offered by this patch is to always source virtio's
Kconfig in drivers/Kconfig, and remove it from the appropriate arch
Kconfigs. Additionally, a virtio menu entry has been added so virtio
drivers don't show up in the general drivers menu.
This way anyone can use virtio, though it's arguably less accessible
(and neat!) for virtualization users now.
Note: some architectures (mips and sh) seem to have a VIRTUALIZATION
menu merely for sourcing virtio's Kconfig, so that menu is removed too.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
perf: Remove the nmi parameter from the oprofile_perf backend
x86, perf: Make copy_from_user_nmi() a library function
perf: Remove perf_event_attr::type check
x86, perf: P4 PMU - Fix typos in comments and style cleanup
perf tools: Make test use the preset debugfs path
perf tools: Add automated tests for events parsing
perf tools: De-opt the parse_events function
perf script: Fix display of IP address for non-callchain path
perf tools: Fix endian conversion reading event attr from file header
perf tools: Add missing 'node' alias to the hw_cache[] array
perf probe: Support adding probes on offline kernel modules
perf probe: Add probed module in front of function
perf probe: Introduce debuginfo to encapsulate dwarf information
perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
perf probe: Remove redundant dwarf functions
perf probe: Move strtailcmp to string.c
perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
tracing/kprobe: Update symbol reference when loading module
tracing/kprobes: Support module init function probing
kprobes: Return -ENOENT if probe point doesn't exist
...
pit_clockevent wants to replaced in the argument of the callback
function as well.
Reported-by; Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix few issues in the Netlogic code:
- Use handle_percpu_irq to handle per-cpu interrupts
- Remove unused function nlm_common_ipi_handler()
- Call scheduler_ipi() on SMP_RESCHEDULE_YOURSELF
- Enable interrupts in nlm_smp_finish()
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d6d5d5c4a (MIPS: Sibyte: Convert to new irq_chip functions)
removed the mask function which breaks irq_shutdown(). Restore it.
Reported-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2460/
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 6be63bbbda (lmo) rsp.
af3a1f6f48 (kernel.org) the Malta code does
no longer probe for presence of GCMP if CMP is not configured. This means
that the variable gcmp_present well be left at its default value of -1
which normally is meant to indicate that GCMP has not yet been mmapped.
This non-zero value is now interpreted as GCMP being present resulting
in a write attempt to a GCMP register resulting in a crash.
Reported and a build fix on top of my fix by Rob Landley <rob@landley.net>.
Reported-by: Rob Landley <rob@landley.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2413/
Renumbering was necessary because I had already wired up setns(2) in the
linux-mips.org tree in commit c3fce54644cabbb90700cc3acc040718a377f609
[MIPS: Wire up new sendmmsg syscall.] but the same syscall numbers were
used by 7b21fddd08 [ns: Wire up the setns
system call] resulting in a conflict.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit ee6114202e48dc282c6d04741e9c5d7171eb8bb8 (lmo) rsp.
1685f3b158 (kernel.org) ["MIPS: SMTC: Move
declaration of smtc_init_secondary to <asm/smtc.h>."] didn't quite do
that - it rather lost the declaration of smtc_init_secondary resulting in
a build error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code in arch/mips/kernel/i8259.c still hasn't been converted to
using struct syscore_ops instead of a sysdev for resume and shutdown.
As a result, this code doesn't build any more after suspend, resume
and shutdown callbacks have been removed from struct sysdev_class.
Fix this problem by converting i8259.c to using syscore_ops.
Reported-and-tested-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Make sure that the 'static' keywork is at the beginning of declaration
for arch/mips/include/asm/mach-jz4740/gpio.h
This gets rid of warnings like
warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Also a few tiny whitespace changes.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a NODE level to the generic cache events which is used to measure
local vs remote memory accesses. Like all other cache events, an
ACCESS is HIT+MISS, if there is no way to distinguish between reads
and writes do reads only etc..
The below needs filling out for !x86 (which I filled out with
unsupported events).
I'm fairly sure ARM can leave it like that since it doesn't strike me as
an architecture that even has NUMA support. SH might have something since
it does appear to have some NUMA bits.
Sparc64, PowerPC and MIPS certainly want a good look there since they
clearly are NUMA capable.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Miller <davem@davemloft.net>
Cc: Anton Blanchard <anton@samba.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1303508226.4865.8.camel@laptop
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The nmi parameter indicated if we could do wakeups from the current
context, if not, we would set some state and self-IPI and let the
resulting interrupt do the wakeup.
For the various event classes:
- hardware: nmi=0; PMI is in fact an NMI or we run irq_work_run from
the PMI-tail (ARM etc.)
- tracepoint: nmi=0; since tracepoint could be from NMI context.
- software: nmi=[0,1]; some, like the schedule thing cannot
perform wakeups, and hence need 0.
As one can see, there is very little nmi=1 usage, and the down-side of
not using it is that on some platforms some software events can have a
jiffy delay in wakeup (when arch_irq_work_raise isn't implemented).
The up-side however is that we can remove the nmi parameter and save a
bunch of conditionals in fast paths.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/n/tip-agjev8eu666tvknpb3iaj0fg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stack unwinding is done by code examination. For kernelspace, the
already existing unwind function is utilized that uses kallsyms to
quickly find the beginning of functions. For userspace a new function
was added that examines code at and before the pc.
Signed-off-by: Daniel Kalmar <kalmard@homejinni.com>
Signed-off-by: Gergely Kis <gergely@homejinni.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
The unwind_stack_by_address variant supports unwinding based
on any kernel code address.
This symbol is also exported so it can be called from modules.
Signed-off-by: Daniel Kalmar <kalmard@homejinni.com>
Signed-off-by: Gergely Kis <gergely@homejinni.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only the Siemens-Nixdorf RM series workstations and the Jazz family
workstations have PC speakers built in; Malta can connect one via the
infamous AMR connector with an AMR sound card or a little creativity.
So we don't want to offer the PC speaker driver on all MIPS systems.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20110601180611.061710714@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Lenghty lists of the kind "depends on ARCH1 || ARCH2 ... || ARCH123" are
usually either wrong or too coarse grained. Or plain an ugly sin.
[ tglx: Fixed up amigaone ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Gerhard Pircher <gerhard_pircher@gmx.net>
Link: http://lkml.kernel.org/r/20110601180610.984881988@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86 defines PIT_LATCH as LATCH which in <linux/timex.h> is defined as
((CLOCK_TICK_RATE + HZ/2) / HZ) and <asm/timex.h> again defines
CLOCK_TICK_RATE as PIT_TICK_RATE.
MIPS defines PIT_LATCH as LATCH which in <linux/timex.h> is defined as
((CLOCK_TICK_RATE + HZ/2) / HZ) and <asm/timex.h> again defines
CLOCK_TICK_RATE as 1193182.
ARM defines PITCH_LATCH as ((PIT_TICK_RATE + HZ / 2) / HZ) - and that's
the sanest thing and equivalent to above definitions so use that as the
new definition in <linux/i8253.h>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20110601180610.832810002@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move them to drivers/clocksource/i8253.c and remove the
implementations in arch/
[ tglx: Avoid the extra file in lib - folded arch patches in. The
export will become conditional in a later step ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20110601180610.221426078@duck.linux-mips.net
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Fix PM QOS's user mode interface to work with ASCII input
PM / Hibernate: Update kerneldoc comments in hibernate.c
PM / Hibernate: Remove arch_prepare_suspend()
PM / Hibernate: Update some comments in core hibernate code
By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT,
CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used
to test for existence of find bitops anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:
* cgroup creation is out-of-control
* cgroup name can conflict when pids are looping
* it is not possible to have a single process handling a lot of
namespaces without falling in a exponential creation time
* we may want to create a namespace without creating a cgroup
The ns_cgroup was replaced by a compatibility flag 'clone_children',
where a newly created cgroup will copy the parent cgroup values.
The userspace has to manually create a cgroup and add a task to
the 'tasks' file.
This patch removes the ns_cgroup as suggested in the following thread:
https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html
The 'cgroup_clone' function is removed because it is no longer used.
This is a userspace-visible change. Commit 45531757b4 ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal. Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most arches define CONFIG_DEBUG_STACK_USAGE exactly the same way. Move it
to lib/Kconfig.debug so each arch doesn't have to define it. This
obviously makes the option generic, but that's fine because the config is
already used in generic code.
It's not obvious to me that sysrq-P actually does anything caution by
keeping the most inclusive wording.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fold all the mmu_gather rework patches into one for submission
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All architectures supporting hibernation define
arch_prepare_suspend() as an empty function, so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
A new utility function (core_kernel_data()) is used to determine if a
passed in address is part of core kernel data or not. It may or may not
return true for RO data, but this utility must work for RW data.
Thus both _sdata and _edata must be defined and continuous,
without .init sections that may later be freed and replaced by
volatile memory (memory that can be freed).
This utility function is used to determine if data is safe from
ever being freed. Thus it should return true for all RW global
data that is not in a module or has been allocated, or false
otherwise.
Also change core_kernel_data() back to the more precise _sdata condition
and document the function.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: JamesE.J.Bottomley <jejb@parisc-linux.org>
Link: http://lkml.kernel.org/r/1305855298.1465.19.camel@gandalf.stny.rr.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
----
arch/alpha/kernel/vmlinux.lds.S | 1 +
arch/m32r/kernel/vmlinux.lds.S | 1 +
arch/m68k/kernel/vmlinux-std.lds | 2 ++
arch/m68k/kernel/vmlinux-sun3.lds | 1 +
arch/mips/kernel/vmlinux.lds.S | 1 +
arch/parisc/kernel/vmlinux.lds.S | 3 +++
kernel/extable.c | 12 +++++++++++-
7 files changed, 20 insertions(+), 1 deletion(-)
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
sched: Fix and optimise calculation of the weight-inverse
sched: Avoid going ahead if ->cpus_allowed is not changed
sched, rt: Update rq clock when unthrottling of an otherwise idle CPU
sched: Remove unused parameters from sched_fork() and wake_up_new_task()
sched: Shorten the construction of the span cpu mask of sched domain
sched: Wrap the 'cfs_rq->nr_spread_over' field with CONFIG_SCHED_DEBUG
sched: Remove unused 'this_best_prio arg' from balance_tasks()
sched: Remove noop in alloc_rt_sched_group()
sched: Get rid of lock_depth
sched: Remove obsolete comment from scheduler_tick()
sched: Fix sched_domain iterations vs. RCU
sched: Next buddy hint on sleep and preempt path
sched: Make set_*_buddy() work on non-task entities
sched: Remove need_migrate_task()
sched: Move the second half of ttwu() to the remote cpu
sched: Restructure ttwu() some more
sched: Rename ttwu_post_activation() to ttwu_do_wakeup()
sched: Remove rq argument from ttwu_stat()
sched: Remove rq->lock from the first half of ttwu()
sched: Drop rq->lock from sched_exec()
...
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix rt_rq runtime leakage bug
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (107 commits)
perf stat: Add more cache-miss percentage printouts
perf stat: Add -d -d and -d -d -d options to show more CPU events
ftrace/kbuild: Add recordmcount files to force full build
ftrace: Add self-tests for multiple function trace users
ftrace: Modify ftrace_set_filter/notrace to take ops
ftrace: Allow dynamically allocated function tracers
ftrace: Implement separate user function filtering
ftrace: Free hash with call_rcu_sched()
ftrace: Have global_ops store the functions that are to be traced
ftrace: Add ops parameter to ftrace_startup/shutdown functions
ftrace: Add enabled_functions file
ftrace: Use counters to enable functions to trace
ftrace: Separate hash allocation and assignment
ftrace: Create a global_ops to hold the filter and notrace hashes
ftrace: Use hash instead for FTRACE_FL_FILTER
ftrace: Replace FTRACE_FL_NOTRACE flag with a hash of ignored functions
perf bench, x86: Add alternatives-asm.h wrapper
x86, 64-bit: Fix copy_[to/from]_user() checks for the userspace address limit
x86, mem: memset_64.S: Optimize memset by enhanced REP MOVSB/STOSB
x86, mem: memmove_64.S: Optimize memmove by enhanced REP MOVSB/STOSB
...
We only use the three low-order mailbox bits. Leave the upper bits alone
for possible use by drivers and other software.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2090/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Octeon uses different interrupt irq for timer and performance counters.
Set CvmCtl[IPPCI] to correct irq value very early.
Signed-off-by: Chandrakala Chavva <cchavva@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/2085/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Assume that the boot loader knows the physical memory of the system and
deduce that information from the contents of the SDRAM control register.
It is still possible to override with with the "mem=" parameter, but we
have a sensible default now.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634u are using minuses between the blocks
of the MAC address and other devices are using colons to separate them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2366/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.
The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some embedded devices like the Netgear WNDR3300 have two SSB based cards
without an own sprom on the pci bus. We have to provide two different
fallback sproms for these and this was not possible with the old solution.
In the bcm47xx architecture the sprom data is stored in the nvram in the
main flash storage. The architecture code will be able to fill the sprom
with the stored data based on the bus where the device was found.
The bcm63xx code should do the same thing as before, just using the new
API.
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
According to the databooks, the Au1000 DMA engine must be programmed with
the physical FIFO addresses. This patch does that; furthermore this
opened the possibility to get rid of a lot of now unnecessary address
defines.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Rewrite ethernet setup to use runtime cpu detection, and also clean up
the ethernet base address mess as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Convert the PM sysdev to syscore_ops and clean up the ddma addresses a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the PM sysdev to use syscore_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
replace au_readl/au_writel with __raw_readl/__raw_writel,
and clean up IC-related stuff from the headers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes a build failure with gpio_keys and CONFIG_GPIOLIB=n (mtx1):
CC drivers/input/keyboard/gpio_keys.o
gpio_keys.c: In function 'gpio_keys_report_event':
gpio_keys.c:325:2: error: implicit declaration of function 'gpio_get_value_cansleep'
gpio_keys.c: In function 'gpio_keys_setup_key':
gpio_keys.c:390:3: error: implicit declaration of function 'gpio_set_debounce'
Also add stubs for the other new functions.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2346/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting Config[OD] gets rid of a _LOT_ of spurious CPLD interrupts,
but also decreases overall performance a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2347/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds the driver for the ETOP Packet Processing Engine (PPE32)
found inside the XWAY family of Lantiq MIPS SoCs. This driver makes 100MBit
ethernet work. Support for all 8 dma channels, gbit and the embedded switch
found on the ar9/vr9 still needs to be implemented.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2357/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the DMA engine found inside the XWAY family of
SoCs. The engine has 5 ports and 20 channels.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XWAY family allows to extend the number of gpios by using shift
registers or latches. This patch adds the 2 drivers needed for this. The
extended gpios are output only.
[ralf@linux-mips.org: Fixed ltq_stp_probe section() attributes.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2258/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Lantiq family of SoCs have a EBU (External Bus Unit). This patch adds
the driver that allows us to use the EBU as a PCI controller. In order for
PCI to work the EBU is set to endianess swap all the data. In addition we
need to make use of SWAP_IO_SPACE for device->host DMA to work.
The clock of the PCI works in several modes (internal/external). If this
is not configured correctly the SoC will hang.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the Lantiq XWAY family of Mips24KEc SoCs.
* Danube (PSB50702)
* Twinpass (PSB4000)
* AR9 (PSB50802)
* Amazon SE (PSB5061)
The Amazon SE is a lightweight SoC and has no PCI as well as a different
clock. We split the code out into seperate files to handle this.
The GPIO pins on the SoCs are multi function and there are several bits
we can use to configure the pins. To be as compatible as possible to
GPIOLIB we add a function
int lq_gpio_request(unsigned int pin, unsigned int alt0,
unsigned int alt1, unsigned int dir, const char *name);
which lets you configure the 2 "alternate function" bits. This way drivers like
PCI can make use of GPIOLIB without a cubersome wrapper.
The PLL code inside arch/mips/lantiq/xway/clk-xway.c is voodoo to me. It was
taken from a 2.4.20 source tree and was never really changed by me since then.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add initial support for Mips based SoCs made by Lantiq. This series will add
support for the XWAY family.
The series allows booting a minimal system using a initramfs or NOR. Missing
drivers and support for Amazon and GPON family will be provided in a later
series.
[Ralf: Remove some cargo cult programming and fixed formatting.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2252/
Patchwork: https://patchwork.linux-mips.org/patch/2371/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds pci/pci-xlr.c to support for XLR PCI/PCI-X interface and XLS PCIe
interface.
Update irq.c to ack PCI interrupts, use irq handler data to do the
PCI/PCIe bus ack.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable XLR CPU support, SMP, initramfs based root filesystem etc.
[ralf@linux-mips.org: shrink the defconfig file through make savedefconfig.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
