The pushf/popf in switch_to are ONLY used to switch IOPL. Making this
explicit in C code is more clear. This pushf/popf pair was added as a
bugfix for leaking IOPL to unprivileged processes when using
sysenter/sysexit based system calls (sysexit does not restore flags).
When requesting an IOPL change in sys_iopl(), it is just as easy to change
the current flags and the flags in the stack image (in case an IRET is
required), but there is no reason to force an IRET if we came in from the
SYSENTER path.
This change is the minimal solution for supporting a paravirtualized Linux
kernel that allows user processes to run with I/O privilege. Other
solutions require radical rewrites of part of the low level fault / system
call handling code, or do not fully support sysenter based system calls.
Unfortunately, this added one field to the thread_struct. But as a bonus,
on P4, the fastest time measured for switch_to() went from 312 to 260
cycles, a win of about 17% in the fast case through this performance
critical path.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Privilege checking cleanup. Originally, these diffs were much greater, but
recent cleanups in Linux have already done much of the cleanup. I added
some explanatory comments in places where the reasoning behind certain
tests is rather subtle.
Also, in traps.c, we can skip the user_mode check in handle_BUG(). The
reason is, there are only two call chains - one via die_if_kernel() and one
via do_page_fault(), both entering from die(). Both of these paths already
ensure that a kernel mode failure has happened. Also, the original check
here, if (user_mode(regs)) was insufficient anyways, since it would not
rule out BUG faults from V8086 mode execution.
Saving the %ss segment in show_regs() rather than assuming a fixed value
also gives better information about the current kernel state in the
register dump.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some more assembler cleanups I noticed along the way.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also, setting PDPEs in PAE mode does not require atomic operations, since the
PDPEs are cached by the processor, and only reloaded on an explicit or
implicit reload of CR3.
Since the four PDPEs must always be present in an active root, and the kernel
PDPE is never updated, we are safe even from SMIs and interrupts / NMIs using
task gates (which reload CR3). Actually, much of this is moot, since the user
PDPEs are never updated either, and the only usage of task gates is by the
doublefault handler. It appears the only place PGDs get updated in PAE mode
is in init_low_mappings() / zap_low_mapping() for initial page table creation
and recovery from ACPI sleep state, and these sites are safe by inspection.
Getting rid of the cmpxchg8b saves code space and 720 cycles in pgd_alloc on
P4.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Subtle fix: load_TLS has been moved after saving %fs and %gs segments to avoid
creating non-reversible segments. This could conceivably cause a bug if the
kernel ever needed to save and restore fs/gs from the NMI handler. It
currently does not, but this is the safest approach to avoiding fs/gs
corruption. SMIs are safe, since SMI saves the descriptor hidden state.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 inline assembler cleanup.
This change encapsulates descriptor and task register management. Also,
it is possible to improve assembler generation in two cases; savesegment
may store the value in a register instead of a memory location, which
allows GCC to optimize stack variables into registers, and MOV MEM, SEG
is always a 16-bit write to memory, making the casting in math-emu
unnecessary.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 arch cleanup. Introduce the serialize macro to serialize processor
state. Why the microcode update needs it I am not quite sure, since wrmsr()
is already a serializing instruction, but it is a microcode update, so I will
keep the semantic the same, since this could be a timing workaround. As far
as I can tell, this has always been there since the original microcode update
source.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 Inline asm cleanup. Use cr/dr accessor functions.
Also, a potential bugfix. Also, some CR accessors really should be volatile.
Reads from CR0 (numeric state may change in an exception handler), writes to
CR4 (flipping CR4.TSD) and reads from CR2 (page fault) prevent instruction
re-ordering. I did not add memory clobber to CR3 / CR4 / CR0 updates, as it
was not there to begin with, and in no case should kernel memory be clobbered,
except when doing a TLB flush, which already has memory clobber.
I noticed that page invalidation does not have a memory clobber. I can't find
a bug as a result, but there is definitely a potential for a bug here:
#define __flush_tlb_single(addr) \
__asm__ __volatile__("invlpg %0": :"m" (*(char *) addr))
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes the vDSO use nops for all its padding around instructions,
rather than sometimes zeros, and nop-pads the end of the area containing
instructions to a 32-byte cache line, to keep text and data in separate
lines.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is subarch update for ES7000. I've modified platform check code and
removed unnecessary OEM table parsing for newer systems that don't use OEM
information during boot. Parsing the table in fact is causing problems,
and the platform doesn't get recognized. The patch only affects the ES7000
subach.
Signed-off-by: <Natalie.Protasevich@unisys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 generic subarchitecture requires explicit dmi strings or command line
to enable bigsmp mode. The patch below removes that restriction, and uses
bigsmp as soon as it finds more than 8 logical CPUs, Intel processors and
xAPIC support.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o With introduction of kexec as boot-loader, the assumption that parameter
segment will always be loaded at lower address than kernel and will be
addressable by early bootup page tables is no longer valid. In kexec on
panic case parameter segment might well be loaded beyond kernel image and
might not be addressable by early boot page tables.
o This case might hit in the scenario where user has reserved a chunk of
memory for second kernel, for example 16MB to 64MB, and has also built
second kernel for physical memory location 16MB. In this case kexec has no
choice but to load the parameter segment at a higher address than new kernel
image at safe location where new kernel does not stomp it.
o Though problem should automatically go away once relocatable kernel for i386
is in place and kexec can determine the location of new kernel at run time
and load parameter segment at lower address than kernel image. But till then
this patch can go in (assuming it does not break something else).
o This patch moves up the boot parameter saving code. Now boot parameters
are copied out in protected mode before page tables are initialized. This
will ensure that parameter segment is always addressable irrespective of
its physical location.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the virtual 86 machine reaches an instruction which raises a General
Protection Fault (such as CLI or STI), the instruction is emulated (in
handle_vm86_fault). However, the emulation ignored the TF bit, so the
hardware debug interrupt was not invoked after such an emulated instruction
(and the DOS debugger missed it).
This patch fixes the problem by emulating the hardware debug interrupt as
the last action before control is returned to the VM86 program.
Signed-off-by: Petr Tesarik <kernel@tesarici.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory descriptors that comprise the EFI memory map are not fixed in
stone such that the size could change in the future. This uses the memory
descriptor size obtained from EFI to iterate over the memory map entries
during boot. This enables the removal of an x86 specific pad (and ifdef)
in the EFI header. I also couldn't stomach the broken up nature of the
function to put EFI runtime calls into virtual mode any longer so I fixed
that up a bit as well.
For reference, this patch only impacts x86.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only use read_timer_tsc only when CPU has TSC. Thanks to Andrea for
pointing this out. Should not be issue on any platforms as all recent
systems that has HPET also has CPUs that supports TSC. The patch is still
required for correctness.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch pushes the creation of a rare signal frame (SIGBUS or SIGSEGV)
into a separate function, thus saving stackspace in the main
do_page_fault() stackframe. The effect is 132 bytes less of stack used by
the typical do_page_fault() invocation - resulting in a denser
cache-layout.
(Another minor effect is that in case of kernel crashes that come from a
pagefault, we add less space to the already existing frame, giving the
crash functions a slightly higher chance to do their stuff without
overflowing the stack.)
(The changes also result in slightly cleaner code.)
argument bugfix from "Guillaume C." <guichaz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The LOG_BUF_SHIFT from lib/Kconfig.debug is sufficient.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Paul Mundt <lethal@Linux-SH.ORG>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has fixed the following warnings.
arch/mips/kernel/genex.S:250:5: warning: "CONFIG_64BIT" is not defined
arch/mips/math-emu/cp1emu.c:1128:5: warning: "__mips64" is not defined
arch/mips/math-emu/cp1emu.c:1206:5: warning: "__mips64" is not defined
arch/mips/math-emu/cp1emu.c:1270:5: warning: "__mips64" is not defined
arch/mips/math-emu/cp1emu.c:323:5: warning: "__mips64" is not defined
arch/mips/math-emu/cp1emu.c:808:5: warning: "__mips64" is not defined
arch/mips/math-emu/cp1emu.c:953:5: warning: "__mips64" is not defined
arch/mips/mm/tlbex.c:519:5: warning: "CONFIG_64BIT" is not defined
include/asm/reg.h:73:5: warning: "CONFIG_64BIT" is not defined
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The addtion of SYS_SUPPORTS_*_KERNEL and CPU_SUPPORTS_*_KERNEL is halfway.
This patch has added more SYS_SUPPORTS_*_KERNEL and CPU_SUPPORTS_*_KERNEL
to arch/mips/Kconfig. Please apply.
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the MIPS coherency configuration such that we always keep the mapping
state in <asm/pci.h> when we need to on non-coherent platforms.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has changed from VR41XX to VR4100 series in arch/mips/Kconfig.
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
$ make menuconfig
scripts/kconfig/mconf arch/i386/Kconfig
drivers/char/Kconfig:847:warning: 'select' used by config symbol
'TANBAC_TB0219' refer to undefined symbol 'PCI_VR41XX'
Here is a patch for this warning fix.
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the virtual MIPS system that is emulated by Qemu. See
http://www.linux-mips.org/wiki/Qemu for a detailed current status.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We also need this patch for removing mips vr4181.
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There seem to be no more users or interest in the NEC Osprey evaluation
system for the NEC VR4181 SOC which is an old part anyway, so remove the
code. More information on the Osprey can be found at
http://www.linux-mips.org/wiki/Osprey.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has changed system type name in proc for vr41xx.
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has updated IRQ handling for vr41xx.
o added common IRQ dispatch
o changed IRQ number in int-handler.S
o added resource management to icu.c
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep_interruptible() instead of schedule_timeout() in ppc64-specific
code to cleanup/simplify the sleeping logic. Change the units of the
parameter of do_event_scan_all_cpus() to milliseconds from jiffies. The
return value of rtas_extended_busy_delay_time() was incorrectly being used
as a jiffies value (it is actually milliseconds), which is fixed by using
the value as a parameter to msleep_interruptible(). Also, use
rtas_extended_busy_delay_time() in another case where similar logic is
duplicated.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to indicate to the hypervisor that it needs to save our VMX
registers when switching partitions on a shared-processor system, just as
it needs to for FP and PMC registers.
This could be made to be on-demand when VMX is used, but we don't do that
for FP nor PMC right now either so let's not overcomplicate things.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: <engebret@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
xmon will do nothing but noise on a G5 if BOOTX_TEXT is not enabled.
mention the recognized kernel cmdline options for xmon.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Paul Mackeras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the cpci690 platform code:
- pass mem size in from bootwrapper via bi_rec
- some minor fixups
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the katana platform support code:
- if booted as zImage, pass mem size in via bi_req from bootwrapper
- if booted as uImage, get mem size from bd_info passed in from u-boot
- add support for 82544 present on katana 752i's
- set cacheline size on pci devices
- some minor fixups
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates and enhancement to the ppc32 mv64x60 code:
- move code to get mem size from mem ctlr to bootwrapper
- address some errata in the mv64360 pic code
- some minor cleanups
- export one of the bridge's regs via sysfs so user daemon can watch for
extraction events
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added cputable entry for 7448 as well adding it to checks for saving and
restoring of cpu state.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add declaration and cacheable_memcpy(). I'll be needing this function in
new 4xx EMAC driver I'm going to submit to netdev soon.
IMHO, the better place for the declaration would be asm-powerpc/string.h,
unfortunately, ppc64 doesn't have this function, so asm-ppc/system.h is the
next best place.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add dcr_base field to ocp_func_mal_data. This is preparation step for the
new EMAC driver.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move 4xx PHY_MODE_XXX defines to asm-ppc/ibm_ocp.h. This is a preparation
step for the new EMAC driver.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
"745/755" (pvr_value:0x00083000) is a catch-all entry.
Since arch/ppc/kernel/misc.S:identify_cpu() returns on first match,
move this lower in the table so 750CXe DD2.4 (pvr_value:0x00083214)
may be correctly enumerated.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds support for the two PCI busses on MPC83xx and the MPC834x SYS/PIBS
reference board.
The code initializes PCI inbound/outbound windows, allocates and registers
PCI memory/io space. Be aware that setup of the PCI buses on the PIBs
board is expected to be done by the firmware.
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is the default configuration for Marvell EV64360BP board. It has been
tested on the board.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for Marvell EV64360BP board. So far, it supports
mpsc serial console, gigabit ethernet, jffs2 root filesystem, etc. Other
device support, like watchdog, RTC, will be added later.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the ability to identify an SOC by a name and id. There are cases in
which the integer identifier is not sufficient to specify a specific SOC.
In these cases we can use a string to further qualify the match.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable IBM405_ERR77 and IBM405_ERR51 errata workarounds for 405EP. This
chip has these problems fixed.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix STD_UART_OP definitions in Bamboo and Luan board ports which were
causing "initialization makes pointer from integer without a cast"
warnings.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix PowerPC NPe405H EMAC Tx channel assignments. EMAC unit in this chip
uses common for 4xx "two Tx / one Rx" configuration.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
flush_dcache_icache_page() will be called on an instruction page fault. We
can't sleep in the fault handler, so use kmap_atomic() instead of just
kmap() for the Book-E case.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the appropriate cputable entry for PPC440SP so cache line sizes are
configured correctly.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No one uses find_name.c and no one seems to care about either. So I'm
removing it.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Renamed global variables used to convey if the watchdog is enabled and
periodicity of the timer and moved the declarations into a header for these
variables
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 2nd serial port on the MPC8560 ADS was not being configured correctly
and thus could not be used as a console. Updated the defconfig for the
board to configure the proper SCC channel for the 2nd serial port.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a field to struct ocp_func_emac_data that allows
platform-specific unsupported PHY features to be passed in to the ibm_emac
ethernet driver.
This patch also adds some logic for the Bamboo eval board to populate this
field based on the dip switches on the board. This is a workaround for the
improperly biased RJ-45 sockets on the Rev. 0 Bamboo.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added ppc_sys device and system definitions for PowerQUICC II devices.
This will allow drivers for PQ2 to be proper platform device drivers.
Which can be shared on PQ3 processors with the same peripherals.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PowerPC 40x and Book-E processors support a watchdog timer at the processor
core level. The timer has implementation dependent timeout frequencies
that can be configured by software.
One the first Watchdog timeout we get a critical exception. It is left to
board specific code to determine what should happen at this point. If
nothing is done and another timeout period expires the processor may
attempt to reset the machine.
Command line parameters:
wdt=0 : disable watchdog (default)
wdt=1 : enable watchdog
wdt_period=N : N sets the value of the Watchdog Timer Period.
The Watchdog Timer Period meaning is implementation specific. Check
User Manual for the processor for more details.
This patch is based off of work done by Takeharu Kato.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support ochi-ppc-soc.c on IBM stb04xxx platforms
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the PCORE board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the SPD823TS board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the SM850 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the REDWOOD board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the RAINIER board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the OAK board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the MENF1 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the MCPN765 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the K2 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the CEDAR board no longer exists, removing the defconfig for it
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the BEECH board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the ASH board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the ADIR board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This #define is only used on sparc.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I don't think we need to call hugetlb_clean_stale_pgtable() anymore
in 2.6.13 because of the rework with free_pgtables(). It now collect
all the pte page at the time of munmap. It used to only collect page
table pages when entire one pgd can be freed and left with staled pte
pages. Not anymore with 2.6.13. This function will never be called
and We should turn it into a BUG_ON.
I also spotted two problems here, not Adam's fault :-)
(1) in huge_pte_alloc(), it looks like a bug to me that pud is not
checked before calling pmd_alloc()
(2) in hugetlb_clean_stale_pgtable(), it also missed a call to
pmd_free_tlb. I think a tlb flush is required to flush the mapping
for the page table itself when we clear out the pmd pointing to a
pte page. However, since hugetlb_clean_stale_pgtable() is never
called, so it won't trigger the bug.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For demand faulting, we cannot assume that the page tables will be
populated. Do what the rest of the architectures do and test p?d_present()
while walking down the page table.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial Post (Wed, 17 Aug 2005)
This patch moves the
if (! pte_none(*pte))
hugetlb_clean_stale_pgtable(pte);
logic into huge_pte_alloc() so all of its callers can be immune to the bug
described by Kenneth Chen at http://lkml.org/lkml/2004/6/16/246
> It turns out there is a bug in hugetlb_prefault(): with 3 level page table,
> huge_pte_alloc() might return a pmd that points to a PTE page. It happens
> if the virtual address for hugetlb mmap is recycled from previously used
> normal page mmap. free_pgtables() might not scrub the pmd entry on
> munmap and hugetlb_prefault skips on any pmd presence regardless what type
> it is.
Unless I am missing something, it seems more correct to place the check inside
huge_pte_alloc() to prevent a the same bug wherever a huge pte is allocated.
It also allows checking for this condition when lazily faulting huge pages
later in the series.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With cleanups from Dave Hansen <haveblue@us.ibm.com>
SPARSEMEM_EXTREME makes mem_section a one dimensional array of pointers to
mem_sections. This two level layout scheme is able to achieve smaller
memory requirements for SPARSEMEM with the tradeoff of an additional shift
and load when fetching the memory section. The current SPARSEMEM
implementation is a one dimensional array of mem_sections which is the
default SPARSEMEM configuration. The patch attempts isolates the
implementation details of the physical layout of the sparsemem section
array.
SPARSEMEM_EXTREME requires bootmem to be functioning at the time of
memory_present() calls. This is not always feasible, so architectures
which do not need it may allocate everything statically by using
SPARSEMEM_STATIC.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A new option for SPARSEMEM is ARCH_SPARSEMEM_EXTREME. Architecture
platforms with a very sparse physical address space would likely want to
select this option. For those architecture platforms that don't select the
option, the code generated is equivalent to SPARSEMEM currently in -mm.
I'll be posting a patch on ia64 ml which uses this new SPARSEMEM feature.
ARCH_SPARSEMEM_EXTREME makes mem_section a one dimensional array of
pointers to mem_sections. This two level layout scheme is able to achieve
smaller memory requirements for SPARSEMEM with the tradeoff of an
additional shift and load when fetching the memory section. The current
SPARSEMEM -mm implementation is a one dimensional array of mem_sections
which is the default SPARSEMEM configuration. The patch attempts isolates
the implementation details of the physical layout of the sparsemem section
array.
ARCH_SPARSEMEM_EXTREME depends on 64BIT and is by default boolean false.
I've boot tested under aim load ia64 configured for ARCH_SPARSEMEM_EXTREME.
I've also boot tested a 4 way Opteron machine with !ARCH_SPARSEMEM_EXTREME
and tested with aim.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is part of Thomas Gleixner's generic IRQ patch, which converts
ARM to use the generic IRQ subsystem. Here, we wrap calls to
desc->handler() in an inline function, desc_handle_irq(). This
reduces the size of Thomas' patch since the changes become more
localised.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is part of Thomas Gleixner's generic IRQ patch, which converts
ARM to use the generic IRQ subsystem. Here, we rename two of the
irq_chip methods - wake becomes set_wake, and type becomes set_type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not access children in struct device directly, use
device_for_each_child helper instead. It fixes compilation.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Timothy Baldwin
All data aborts are treated as read accesses. The existing code updates the wrong bit of r1, also the comments are wrong in that the sense of the L bit is inverted.
Signed-off-by: Timothy E. Baldwin <T.E.Baldwin99@members.leeds.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The power management sleep code needs to call cpu_init()
to restore the cpu state after the system resumes from
suspend. Also clear off an un-necessary comment.
Thanks to Dimitry Andric for reporting the bug and
for rmk for pointing out the cause.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
. add support for the M5235EVB board
. add support for the SOM5282 board
. add support for the MOD5272 board
. fix end of memory define for eLITE board
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the THREAD_SIZE define when manipulating the stack instead of
hard coded values (for the 68328 and 68360 sub-architectures).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New architecture and board configuration support for m68knommu.
. add 523x ColdFire support
. add support for SOM5282 and MOD5272 boards
. break up the 527x to be separate 5271 and 5275. There is some
subtle differences that (like RAM config) that need to be dealt with
. add option to support selecting 4k kernel stack
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the 523x ColdFire family of processors
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Zachary Amsden
Roland McGrath
Natalie.Protasevich@unisys.com
Venkatesh Pallipadi
Vivek Goyal
Petr Tesarik
Matt Tolentino
Ingo Molnar
Adrian Bunk
Yoichi Yuasa
Ralf Baechle
Jesper Juhl
Nishanth Aravamudan
Olof Johansson
Olaf Hering
Mark A. Greer
Kumar Gala
Eugene Surovegin
Arthur Othieno
Lee Nicks
Roland Dreier
Matt Porter
Chen, Kenneth W
Adam Litke
Bob Picco
Russell King
Pavel Machek
Timothy Baldwin
Ben Dooks
Miles Bader
Greg Ungerer