Scenario, starting with normal operation
Connected Primary/Secondary UpToDate/UpToDate
NetworkFailure Primary/Unknown UpToDate/DUnknown (frozen)
... more failures happen, secondary loses it's disk,
but eventually is able to re-establish the replication link ...
Connected Primary/Secondary UpToDate/Diskless (resumed; needs to bump uuid!)
We used to just resume/resent suspended requests,
without bumping the UUID.
Which will lead to problems later, when we want to re-attach the disk on
the peer, without first disconnecting, or if we experience additional
failures, because we now have diverging data without being able to
recognize it.
Make sure we also bump the current data generation UUID,
if we notice "peer disk unknown" -> "peer disk known bad".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We already serialize connection state changes,
and other, non-connection state changes (role changes)
while we are establishing a connection.
But if we have an established connection,
then trigger a resync handshake (by primary --force or similar),
until now we just had to be "lucky".
Consider this sequence (e.g. deployment scenario):
create-md; up;
-> Connected Secondary/Secondary Inconsistent/Inconsistent
then do a racy primary --force on both peers.
block drbd0: drbd_sync_handshake:
block drbd0: self 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:25590 flags:0
block drbd0: peer 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:25590 flags:0
block drbd0: peer( Unknown -> Secondary ) conn( WFReportParams -> Connected ) pdsk( DUnknown -> Inconsistent )
block drbd0: peer( Secondary -> Primary ) pdsk( Inconsistent -> UpToDate )
*** HERE things go wrong. ***
block drbd0: role( Secondary -> Primary )
block drbd0: drbd_sync_handshake:
block drbd0: self 0000000000000005:0000000000000000:0000000000000000:0000000000000000 bits:25590 flags:0
block drbd0: peer C90D2FC716D232AB:0000000000000004:0000000000000000:0000000000000000 bits:25590 flags:0
block drbd0: Becoming sync target due to disk states.
block drbd0: Writing the whole bitmap, full sync required after drbd_sync_handshake.
block drbd0: Remote failed to finish a request within 6007ms > ko-count (2) * timeout (30 * 0.1s)
drbd s0: peer( Primary -> Unknown ) conn( Connected -> Timeout ) pdsk( UpToDate -> DUnknown )
The problem here is that the local promotion happens before the sync handshake
triggered by the remote promotion was completed. Some assumptions elsewhere
become wrong, and when the expected resync handshake is then received and
processed, we get stuck in a deadlock, which can only be recovered by reboot :-(
Fix: if we know the peer has good data,
and our own disk is present, but NOT good,
and there is no resync going on yet,
we expect a sync handshake to happen "soon".
So reject a racy promotion with SS_IN_TRANSIENT_STATE.
Result:
... as above ...
block drbd0: peer( Secondary -> Primary ) pdsk( Inconsistent -> UpToDate )
*** local promotion being postponed until ... ***
block drbd0: drbd_sync_handshake:
block drbd0: self 0000000000000004:0000000000000000:0000000000000000:0000000000000000 bits:25590 flags:0
block drbd0: peer 77868BDA836E12A5:0000000000000004:0000000000000000:0000000000000000 bits:25590 flags:0
...
block drbd0: conn( WFBitMapT -> WFSyncUUID )
block drbd0: updated sync uuid 85D06D0E8887AD44:0000000000000000:0000000000000000:0000000000000000
block drbd0: conn( WFSyncUUID -> SyncTarget )
*** ... after the resync handshake ***
block drbd0: role( Secondary -> Primary )
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If in a two-primary scenario, we lost our peer, freeze IO,
and are still frozen (no UUID rotation) when the peer comes back
as Secondary after a hard crash, we will see identical UUIDs.
The "rule_nr = 40" chose to use the "CRASHED_PRIMARY" bit as
arbitration, but that would cause the still running (but frozen) Primary
to become SyncTarget (which it typically refuses), and the handshake is
declined.
Fix: check current roles.
If we have *one* current primary, the Primary wins.
(rule_nr = 41)
Since that is a protocol change, use the newly introduced DRBD_FF_WSAME
to determine if rule_nr = 41 can be applied.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We will support WRITE_SAME, if
* all peers support WRITE_SAME (both in kernel and DRBD version),
* all peer devices support WRITE_SAME
* logical_block_size is identical on all peers.
We may at some point introduce a fallback on the receiving side
for devices/kernels that do not support WRITE_SAME,
by open-coding a submit loop. But not yet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Even if discard_zeroes_data != 0,
if discard_zeroes_if_aligned is set, we assume we can reliably
zero-out/discard using the drbd_issue_peer_discard() helper.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When re-attaching the local backend device to a C_STANDALONE D_DISKLESS
R_PRIMARY with OND_SUSPEND_IO, we may only resume IO if we recognize the
backend that is being attached as D_UP_TO_DATE.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If DRBD lost all path to good data,
and the on-no-data-accessible policy is OND_SUSPEND_IO,
all pending and new IO requests are suspended (will block).
If that setting is OND_IO_ERROR, IO will still be completed.
READ to "clean" areas (e.g. on an D_INCONSISTENT device,
and bitmap indicates a block is already in sync) will succeed.
READ to "unclean" areas (bitmap indicates block is out-of-sync),
will return EIO.
If we are already D_DISKLESS (or D_FAILED), we also return EIO.
Unfortunately, on a former R_PRIMARY C_SYNC_TARGET D_INCONSISTENT,
after replication link loss, new WRITE requests still went through OK.
The would also set the "out-of-sync" bit on their way, so READ after
WRITE would still return EIO. Also, the data generation UUIDs had not
been bumped, we would cause data divergence, without being able to
detect it on the next sync handshake, given the right sequence of events
in a multiple error scenario and "improper" order of recovery actions.
The right thing to do is to return EIO for all new writes,
unless we have access to good, current, D_UP_TO_DATE data.
The "established best practices" way to avoid these situations in the
first place is to set OND_SUSPEND_IO, or even do a hard-reset from
the pri-on-incon-degr policy helper hook.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Possibly sequence of events:
SyncTarget is made Primary, then loses replication link
(only path to good data on SyncSource).
Behavior is then controlled by the on-no-data-accessible policy,
which defaults to OND_IO_ERROR (may be set to OND_SUSPEND_IO).
If OND_IO_ERROR is in fact the current policy, we clear the susp_fen
(IO suspended due to fencing policy) flag, do NOT set the susp_nod
(IO suspended due to no data) flag.
But we forgot to call the IO error completion for all pending,
suspended, requests.
While at it, also add a race check for a theoretically possible
race with a new handshake (network hickup), we may be able to
re-send requests, and can avoid passing IO errors up the stack.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When resync is finished, we already call the "after-resync-target"
handler (on the former sync target, obviously), once per volume.
Paired with the before-resync-target handler, you can create snapshots,
before the resync causes the volumes to become inconsistent,
and discard those snapshots again, once they are no longer needed.
It was also overloaded to be paired with the "fence-peer" handler,
to "unfence" once the volumes are up-to-date and known good.
This has some disadvantages, though: we call "fence-peer" for the whole
connection (once for the group of volumes), but would call unfence as
side-effect of after-resync-target once for each volume.
Also, we fence on a (current, or about to become) Primary,
which will later become the sync-source.
Calling unfence only as a side effect of the after-resync-target
handler opens a race window, between a new fence on the Primary
(SyncTarget) and the unfence on the SyncTarget, which is difficult to
close without some kind of "cluster wide lock" in those handlers.
We would not need those handlers if we could still communicate.
Which makes trying to aquire a cluster wide lock from those handlers
seem like a very bad idea.
This introduces the "unfence-peer" handler, which will be called
per connection (once for the group of volumes), just like the fence
handler, only once all volumes are back in sync, and on the SyncSource.
Which is expected to be the node that previously called "fence", the
node that is currently allowed to be Primary, and thus the only node
that could trigger a new "fence" that could race with this unfence.
Which makes us not need any cluster wide synchronization here,
serializing two scripts running on the same node is trivial.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the replication link breaks exactly during "resync finished" detection,
finishing too early on the sync source could again lead to UUIDs rotated
too fast, and potentially a spurious full resync on next handshake.
Always wait for explicit resync finished state change notification from
the sync target.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make sure we have at least 67 (> AL_UPDATES_PER_TRANSACTION)
al-extents available, and allow up to half of that to be
discarded in one bio.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For consistency, also zero-out partial unaligned chunks of discard
requests on the local backend.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we have the discard_zeroes_if_aligned setting, we should also
check it when setting up our queue parameters on the primary,
not only on the receiving side.
We announce discard support,
UNLESS
* we are connected to a peer that does not support TRIM
on the DRBD protocol level. Otherwise, it would either discard, or
do a fallback to zero-out, depending on its backend and configuration.
* our local backend does not support discards,
or (discard_zeroes_data=0 AND discard_zeroes_if_aligned=no).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We can avoid spurious data divergence caused by partially-ignored
discards on certain backends with discard_zeroes_data=0, if we
translate partial unaligned discard requests into explicit zero-out.
The relevant use case is LVM/DM thin.
If on different nodes, DRBD is backed by devices with differing
discard characteristics, discards may lead to data divergence
(old data or garbage left over on one backend, zeroes due to
unmapped areas on the other backend). Online verify would now
potentially report tons of spurious differences.
While probably harmless for most use cases (fstrim on a file system),
DRBD cannot have that, it would violate our promise to upper layers
that our data instances on the nodes are identical.
To be correct and play safe (make sure data is identical on both copies),
we would have to disable discard support, if our local backend (on a
Primary) does not support "discard_zeroes_data=true".
We'd also have to translate discards to explicit zero-out on the
receiving (typically: Secondary) side, unless the receiving side
supports "discard_zeroes_data=true".
Which both would allocate those blocks, instead of unmapping them,
in contrast with expectations.
LVM/DM thin does set discard_zeroes_data=0,
because it silently ignores discards to partial chunks.
We can work around this by checking the alignment first.
For unaligned (wrt. alignment and granularity) or too small discards,
we zero-out the initial (and/or) trailing unaligned partial chunks,
but discard all the aligned full chunks.
At least for LVM/DM thin, the result is effectively "discard_zeroes_data=1".
Arguably it should behave this way internally, by default,
and we'll try to make that happen.
But our workaround is still valid for already deployed setups,
and for other devices that may behave this way.
Setting discard-zeroes-if-aligned=yes will allow DRBD to use
discards, and to announce discard_zeroes_data=true, even on
backends that announce discard_zeroes_data=false.
Setting discard-zeroes-if-aligned=no will cause DRBD to always
fall-back to zero-out on the receiving side, and to not even
announce discard capabilities on the Primary, if the respective
backend announces discard_zeroes_data=false.
We used to ignore the discard_zeroes_data setting completely.
To not break established and expected behaviour, and suddenly
cause fstrim on thin-provisioned LVs to run out-of-space,
instead of freeing up space, the default value is "yes".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To maintain write-order fidelity accros all volumes in a DRBD resource,
the receiver of a P_BARRIER needs to issue flushes to all volumes.
We used to do this by calling blkdev_issue_flush(), synchronously,
one volume at a time.
We now submit all flushes to all volumes in parallel, then wait for all
completions, to reduce worst-case latencies on multi-volume resources.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The command line parameter the kernel module uses to communicate the
device minor to userland helper is flawed in a way that the device
indentifier "minor-%d" is being truncated to minors with a maximum
of 5 digits.
But DRBD 8.4 allows 2^20 == 1048576 minors,
thus a minimum of 7 digits must be supported.
Reported by Veit Wahlich on drbd-dev.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Regression introduced with 8.4.5
drbd: application writes may set-in-sync in protocol != C
Overwriting the same block (LBA) while a former version is still
"in-flight" to the peer (to be exact: we did not receive the
P_BARRIER_ACK for its epoch yet) would wait for the full epoch of that
former version to be acknowledged by the peer.
In synchronous and quasi-synchronous protocols C and B,
this may double the latency on overwrites.
With protocol A, which is supposed to be asynchronous and only wait for
local completion, it is even worse: it would make overwrites
quasi-synchronous, they would be hit by the full RTT, which protocol A
was specifically meant to avoid, and possibly the additional time it
takes to drain the buffers first.
Particularly bad for databases, or anything else that
does frequent updates to the same blocks (various file system meta data).
No impact if >= rtt passes between updates to the same block.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If thinly provisioned volumes are used, during a resync the sync source
tries to find out if a block is deallocated. If it is deallocated, then
the resync target uses block_dev_issue_zeroout() on the range in
question.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As long as the value is 0 the feature is disabled. With setting
it to a positive value, DRBD limits and aligns its resync requests
to the rs-discard-granularity setting. If the sync source detects
all zeros in such a block, the resync target discards the range
on disk.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If during resync we read only zeroes for a range of sectors assume
that these secotors can be discarded on the sync target node.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When leaving resync states because of disconnect,
do the bitmap write-out synchronously in the drbd_disconnected() path.
When leaving resync states because we go back to AHEAD/BEHIND, or
because resync actually finished, or some disk was lost during resync,
trigger the write-out from after_state_ch().
The bitmap write-out for resync -> ahead/behind was missing completely before.
Note that this is all only an optimization to avoid double-resyncs of
already completed blocks in case this node crashes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The intention was to only suspend IO if some normal bitmap operation is
supposed to be locked out, not always. If the bulk operation is flaged
as BM_LOCKED_CHANGE_ALLOWED, we do not need to suspend IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have drbd
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
The attribute 0 is never used in drbd, so let's use it as pad attribute
in netlink messages. This minimizes the patch.
Note that this patch is only compile-tested.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly direct substitution with occasional adjustment or removing
outdated comments.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces uses of the long obsolete hash interface with
either shash (for non-SG users) or ahash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In case the lower level device size changed, but some other internal
details of the resize did not work out, drbd_determine_dev_size() would
try to restore the previous settings, trusting
drbd_md_set_sector_offsets() to "do the right thing", but overlooked
that this internally may set the meta data base offset based on device size.
This could end up with incomplete on-disk meta data layout change, and
ultimately lead to data corruption (if the failure was not noticed or
ignored by the operator, and other things go wrong as well).
Just remember all meta data related offsets/sizes,
and on error restore them all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
During handshake communication, we also reconsider our device size,
using drbd_determine_dev_size(). Just in case we need to change the
offsets or layout of our on-disk metadata, we lock out application
and other meta data IO, and wait for the activity log to be "idle"
(no more referenced extents).
If this handshake happens just after a connection loss, with a fencing
policy of "resource-and-stonith", we have frozen IO.
If, additionally, the activity log was "starving" (too many incoming
random writes at that point in time), it won't become idle, ever,
because of the frozen IO, and this would be a lockup of the receiver
thread, and consquentially of DRBD.
Previous logic (re-)initialized with a special "empty" transaction
block, which required the activity log to fully drain first.
Instead, write out some standard activity log transactions.
Using lc_try_lock_for_transaction() instead of lc_try_lock() does not
care about pending activity log references, avoiding the potential
deadlock.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To be able to "force out" an activity log transaction,
even if there are no pending updates.
This will be used to relocate the on-disk activity log,
if the on-disk offsets have to be changed,
without the need to empty the activity log first.
While at it, move the definition,
so we can drop the forward declaration of a static helper.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid to prematurely resume application IO: don't set/clear a single
bit, but inc/dec an atomic counter.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't remember a DRBD request as ack_pending, if it is not.
In protocol A, we usually clear RQ_NET_PENDING at the same time we set
RQ_NET_SENT, so when deciding to remember it as ack_pending,
mod_rq_state needs to look at the current request state,
not at the previous state before the current modification was applied.
This should prevent advance_conn_req_ack_pending() from walking the full
transfer log just to find NULL in protocol A, which would cause serious
performance degradation with many "in-flight" requests, e.g. when
working via DRBD-proxy, or with a huge bandwidth-delay product.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
new_disk_conf could be leaked if the follow on checks fail,
so make sure to free it on error if it was not assigned yet.
Found with smatch.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Disconnect should wait for pending bitmap IO.
But if that bitmap IO is not happening, because it is waiting for
pending application IO, and there is no progress, because the fencing
policy suspended application IO because of the disconnect,
then we deadlock.
The bitmap writeout in this case does not care for concurrent
application IO, so there is no point waiting for it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
lsblk should be able to pick up stacking device driver relations
involving DRBD conveniently.
Even though upstream kernel since 2011 says
"DON'T USE THIS UNLESS YOU'RE ALREADY USING IT."
a new user has been added since (bcache),
which sets the precedences for us to use it as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We cannot possibly support SECDISCARD, even if all backend devices would
support it: if our peer is currently unreachable, some instance of the
data may obviously still be recoverable.
We did not set discard_granularity at all. We don't really care (yet),
we only pass them on, so for now, set our granularity to one sector.
blkdev_stack_limits() takes care of the rest.
If we decide we cannot support discards,
not only clear the (not user visible) QUEUE_FLAG_DISCARD,
but set both (user visible) discard_granularity and max_discard_sectors
to zero, to avoid confusion with e.g. lsblk -D.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When accessing out meta data area on disk, we double check the
plausibility of the requested sector offsets, and are very noisy about
it if they look suspicious.
During initial read of our "superblock", for "external" meta data,
this triggered because the range estimate returned by
drbd_md_last_sector() was still wrong.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Suggested by Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Apparently we now implicitly get definitions for BITS_PER_PAGE and
BITS_PER_PAGE_MASK from the pid_namespace.h
Instead of renaming our defines, I chose to define only if not yet
defined, but to double check the value if already defined.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since kernel 3.3, we can use snprintf-style arguments
to create a workqueue.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Lars Ellenberg
Lars Ellenberg
Philipp Reisner
Mike Christie
Linus Torvalds
Nicolas Dichtel
Jens Axboe
Kirill A. Shutemov
Herbert Xu
Tetsuo Handa
Al Viro
Oleg Drokin