s3fb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 or 4 bits are used per pixel. Fix this
by setting the length to 8 or 4, respectively.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| ipc/mq_sysctl.c:26: warning: 'get_mq' defined but not used
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an HFS filesystem is unmounted, it leaks a 2-page bitmap. Also,
under extreme memory pressure, it's possible that hfs_releasepage() may
use a tree pointer that has not been initialized, and if so, the release
request should just be rejected.
[akpm@linux-foundation.org: free_pages(0) is legal, remove obvious comment]
Signed-off-by: Dave Anderson <anderson@redhat.com>
Tested-by: Eugene Teo <eugeneteo@kernel.sg>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
These sensors communicate over a 2 wire bus running a device specific
protocol. The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available. This is handled by
an interrupt that is disabled under all other conditions.
I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!
Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem. If not it should be provided in the
platform data.
I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
efifb will attempt to ioremap a framebuffer even if its starting address
is 0, failing and causing an ugly backtrace in the process. Exit before
probing if this is the case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
uvesafb incorrectly sets the length of the color fields to 6 bits for
PSEUDOCOLOR modes, even though 8 bits are always used per pixel. Fix this
by setting the length to 8.
The switch of the DAC width from the default 6 bits to 8 bits is retained
and tracked internally in the driver, but never exposed to userspace.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The documentation about the meaning of the color component bitfield
lengths in pseudocolor modes is inconsistent. Fix it, so that it
indicates the correct interpretation everywhere, i.e. that 1 << length is
the number of palette entries.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <syrjala@sci.fi>
Acked-by: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fb_notifier_call_chain() is called with info->lock held, i.e. in
do_fb_ioctl() => FBIOPUT_VSCREENINFO => fb_set_var() and the some
notifier callbacks, like fbcon_event_notify(), try to re-acquire
info->lock again.
Remove the lock/unlock_fb_info() in all the framebuffer notifier
callbacks' and be sure to always call fb_notifier_call_chain() with
info->lock held.
Reported-by: Pavel Roskin <proski@gnu.org>
Reported-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
init/initramfs.c:520: warning: 'clean_rootfs' defined but not used
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since Denis is no longer working for Option, I will maintain the driver from
now on.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vm knobs should go in the vm table. Probably too late for
randomize_va_space though.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Marvell M88E1121R Dual GigE PHY
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: remove xfs_flush_space
xfs: flush delayed allcoation blocks on ENOSPC in create
xfs: block callers of xfs_flush_inodes() correctly
xfs: make inode flush at ENOSPC synchronous
xfs: use xfs_sync_inodes() for device flushing
xfs: inform the xfsaild of the push target before sleeping
xfs: prevent unwritten extent conversion from blocking I/O completion
xfs: fix double free of inode
xfs: validate log feature fields correctly
We noticed on parisc that our broadcoms all swapped MAC addresses going
from 2.6.29 to 2.6.30-rc1:
Apr 11 07:48:24 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:30:6e:4b:15:59
Apr 13 07:34:34 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:00:59:15:4b:6e
The problem patch is:
commit 6d348f2c1e
Author: Matt Carlson <mcarlson@broadcom.com>
Date: Wed Feb 25 14:25:52 2009 +0000
tg3: Eliminate tg3_nvram_read_swab()
With the root cause being the use of memcpy to set the mac address:
memcpy(&dev->dev_addr[0], ((char *)&hi) + 2, 2);
memcpy(&dev->dev_addr[2], (char *)&lo, sizeof(lo));
This might work on little endian machines, but it can't on big endian
ones. You have to use the original setting mechanism to be correct on
all architectures.
The attached patch fixes parisc.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that the zero value from the PICB (position in current buffer)
register is not reliable. Use jiffies to correct returned value
from the ring buffer pointer callback.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
- use monotonic posix clock to measure time
- try to avoid reading zero from PICB (position in current buffer) register
- show also measured samples
- when clock is near 41000 or 44100, use exactly these values
(they appears to be reference clocks for hardware manufacturers)
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
docbook: make cleandocs
kbuild: fix spurious initramfs rebuild
Documentation: explain the difference between __bitwise and __bitwise__
kbuild: make it possible for the linker to discard local symbols from vmlinux
kbuild: remove pointless strdup() on arguments passed to new_module() in modpost
kbuild: fix a few typos in top-level Makefile
kbuild: introduce destination-y for exported headers
kbuild: use git svn instead of git-svn in setlocalversion
kconfig: fix update-po-config to accect backslash in input
kbuild: fix option processing for -I in headerdep
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add linux kernel support for YMM state
x86: fix wrong section of pat_disable & make it static
x86: Fix section mismatches in mpparse
x86: fix set_fixmap to use phys_addr_t
x86: Document get_user_pages_fast()
x86, intr-remap: fix eoi for interrupt remapping without x2apic
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/filters: return proper error code when writing filter file
tracing/filters: allow user input integer to be oct or hex
tracing/filters: fix NULL pointer dereference
tracing/filters: NIL-terminate user input filter
ftrace: Output REC->var instead of __entry->var for trace format
Make __stringify support variable argument macros too
tracing: fix document references
tracing: fix splice return too large
tracing: update file->f_pos when splice(2) it
tracing: allocate page when needed
tracing: disable seeking for trace_pipe_raw
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: continue lock debugging despite some taints
lockdep: warn about lockdep disabling after kernel taint
Atttempting to rid us of the problematic work_on_cpu(). Just use
smp_call_fuction_single() here.
This repairs a 10% sysbench(oltp)+mysql regression which Mike reported,
due to
commit 6b44003e5c
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Thu Apr 9 09:50:37 2009 -0600
work_on_cpu(): rewrite it to create a kernel thread on demand
It seems that the kernel calls these acpi-cpufreq functions at a quite
high frequency.
Valdis Kletnieks also reports that this causes 70-90 forks per second on
his hardware.
Cc: Valdis.Kletnieks@vt.edu
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Cc: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
[ Made it use smp_call_function_many() instead of looping over cpu's
with smp_call_function_single() - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Let new-style drivers implement attach_adapter
i2c: Fix sparse warnings for I2C_BOARD_INFO()
i2c-voodoo3: Deprecate in favor of tdfxfb
i2c-algo-pca: Fix use of uninitialized variable in debug message
When POSIX capabilities were introduced during the 2.1 Linux
cycle, the fs mask, which represents the capabilities which having
fsuid==0 is supposed to grant, did not include CAP_MKNOD and
CAP_LINUX_IMMUTABLE. However, before capabilities the privilege
to call these did in fact depend upon fsuid==0.
This patch introduces those capabilities into the fsmask,
restoring the old behavior.
See the thread starting at http://lkml.org/lkml/2009/3/11/157 for
reference.
Note that if this fix is deemed valid, then earlier kernel versions (2.4
and 2.2) ought to be fixed too.
Changelog:
[Mar 23] Actually delete old CAP_FS_SET definition...
[Mar 20] Updated against J. Bruce Fields's patch
Reported-by: Igor Zhbanov <izh1979@gmail.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: stable@kernel.org
Cc: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu: unbreak alpha percpu
mutex: have non-spinning mutexes on s390 by default
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] omap_wdt.c: move probe function to .devinit.text
[WATCHDOG] ks8695_wdt.c: move probe function to .devinit.text
[WATCHDOG] at91rm9200_wdt.c: move probe function to .devinit.text
[WATCHDOG] remove ARM26 sections
[WATCHDOG] orion5x_wdt: Add shutdown callback, use watchdog ping function
[WATCHDOG] i6300esb.c: Restructure initialization of the device
[WATCHDOG] i6300esb.c: Fix the GETSTATUS and GETBOOTSTATUS ioctls.
[WATCHDOG] i6300esb.c: Cleanup
While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Since the first argument to I2C_BOARD_INFO() must be a string constant,
there is no need to parenthesise it, and adding parentheses results in
an invalid initialiser for char[]. gcc obviously accepts this syntax as
an extension, but sparse complains, e.g.:
drivers/net/sfc/boards.c:173:2: warning: array initialized from parenthesized string constant
Therefore, remove the parentheses.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Support for I2C/DDC was recently added to the tdfxfb driver, which
means that the i2c-voodoo3 driver can be deprecated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
A recent change broke debugging of pca_xfer(), fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Also remove the now-useless debug printouts which are supposed to
tell us when the scan starts and ends.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Along with MCP65, MCP67 and 73 also don't set CAP_NCQ. Force it.
Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: NightFox <zaceni2@yandex.ru>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end. With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.
Changes are based in part on code fragment provided in kernel:
bugzilla 13006:
http://bugzilla.kernel.org/show_bug.cgi?id=13006
by Steve Howard <steve@astutenetworks.com>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Januszewski