The existing pcmcia platform_device structure is not used and is not needed by
the pending hx4700 PCMCIA/CF support. So let's remove it.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Drive the two Bluetooth UART output GPIOs (GPIO43_BTUART_TXD, GPIO45_BTUART_RTS)
LOW during sleep mode instead of HIGH. This reduces sleep mode battery discharge
from approximately 46 mA to approximately 30 mA.
Signed-off-by: Oliver Winker <oliver@oli1170.net>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
GPIO105 (nIR_ON) is requested twice: first in gpio_request_array(), then in
pxa_irda_probe(). Consequently the second request fails with EBUSY:
pxa2xx-ir: probe of pxa2xx-ir failed with error -16
This patch removes the first request, allowing pxa_irda_probe() to succeed.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: add minimal support for Nokia RM-696
ARM: OMAP: enable Bluetooth on the PandaBoard
ARM: OMAP: pandora: add support for backlight and poweroff
ARM: OMAP4: board-4430sdp: don't initialize value that is never used
ARM: OMAP3: cm-t3517: add EMAC support
ARM: OMAP: move generic EMAC init to separate file
ARM: OMAP3: RX-51: add explicit mux configuration of tsc2005 control gpios
ARM: OMAP: Add omap_reserve functionality
(includes sync-up to 3.3-rc6)
Failure is reported on hx4700 with kernel v3.3-rc1.
__mfp_validate: GPIO20 is invalid pin
__mfp_validate: GPIO21 is invalid pin
__mfp_validate: GPIO15 is invalid pin
__mfp_validate: GPIO78 is invalid pin
__mfp_validate: GPIO79 is invalid pin
__mfp_validate: GPIO80 is invalid pin
__mfp_validate: GPIO33 is invalid pin
__mfp_validate: GPIO48 is invalid pin
__mfp_validate: GPIO49 is invalid pin
__mfp_validate: GPIO50 is invalid pin
Since pxa_last_gpio is used in mfp-pxa2xx driver. But it's only
updated in pxa-gpio driver that run after mfp-pxa2xx driver.
So update the pxa_last_gpio first in mfp-pxa2xx driver.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Both reboot (via reboot(RB_AUTOBOOT)) and suspend freeze on hx4700.
Registration of pxa_gpio_syscore_ops is moved into pxa-gpio driver,
but it still exists in arch-pxa directory. It resulsts failure on
reboot and suspend.
Now remove the registration code in arch-pxa.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
This regression was introduced by the commit "ARM: pxa: add dummy
clock for sa1100-rtc", id a55b5adaf4.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
The bq24022 on these machines is a very simple regulator using gpios.
One provides the on/off functionality and a second one is used to
change the current between 100 and 500 mA.
This functionality can also be provided by the more generic gpio-regulator.
Therefore convert both machines which makes it possible to remove the
bq24022 driver later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
gpio-pxa driver is shared among arch-pxa and arch-mmp. Clock is the
essential component on pxa3xx/pxa95x and arch-mmp. So we need to
define dummy clock in pxa25x/pxa27x instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Add LED support for the HTC ASIC3. Underlying support is provided by the mfd/asic3 and leds/leds-asic3 drivers. An example configuration is provided by the pxa/hx4700 platform.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
The HP iPAQ hx4700 has 128Mb of flash provided by two Intel StrataFlash devices.
The hx4700 platform configuration defines a single 128Mb flash resource,
resulting in the MTD physmap-flash driver probing the first device only and
presuming the second device is identical:
physmap platform flash device: 08000000 at 00000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008816
physmap-flash: Found 2 x16 devices at 0x4000000 in 32-bit bank
<snip>
erase region 0: offset=0x0,size=0x10000,blocks=4
erase region 1: offset=0x40000,size=0x40000,blocks=255
erase region 2: offset=0x4000000,size=0x10000,blocks=4
erase region 3: offset=0x4040000,size=0x40000,blocks=255
physmap-flash: 2 set(s) of 2 interleaved chips --> 32 partitions of 4096 KiB
Unfortunately the two devices are not identical. The first has a device ID of
0x8816, identifying a bottom parameter device. The second has a device ID of
0x8813, identifying a top parameter device. By not probing the second device,
physmap-flash does not discover the correct block sizes.
This patch splits the configuration into two 64Mb flash resources, forcing
physmap-flash to probe both devices and thus discover the correct block sizes:
physmap platform flash device: 04000000 at 00000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008816
<snip>
erase region 0: offset=0x0,size=0x10000,blocks=4
erase region 1: offset=0x40000,size=0x40000,blocks=255
physmap-flash: 1 set(s) of 2 interleaved chips --> 16 partitions of 4096 KiB
physmap platform flash device: 04000000 at 04000000
physmap-flash: Found 2 x16 devices at 0x0 in 32-bit bank. Manufacturer ID 0x000089 Chip ID 0x008813
<snip>
erase region 0: offset=0x0,size=0x40000,blocks=255
erase region 1: offset=0x3fc0000,size=0x10000,blocks=4
physmap-flash: 1 set(s) of 2 interleaved chips --> 16 partitions of 4096 KiB
Concatenating MTD devices:
(0): "physmap-flash"
(1): "physmap-flash"
into device "physmap-flash"
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
sa1100-rtc driver could be shared among sa1100/pxa/mmp series silicon.
Since clk is used in mmp series silicon, add dummy clock support in
pxa also.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to hard coded irq in rtc-sa1100 driver since we could share
it among arch-sa1100/arch-pxa/arch-mmp.
We still keep hard coded register address since the requirement is
enabling both rtc-sa1100 and rtc-pxa driver. The register addresses
are conflict since they're only two wrappers on the same rtc device.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.
Includes fixes to IMX code from Sascha Hauer.
[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As part of mach/irqs.h include removal from sparse, mainstone.h was missed.
This fixes the compile of the pcmcia driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
The audio on hx4700 needs this to properly work.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
arch/arm/mach-pxa/pxa25x.c and arch/arm/mach-pxa/saarb.c
included 'linux/gpio.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
arch/arm/mach-pxa/pxa27x.c included 'linux/gpio.h' twice, remove
the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
arch/arm/mach-pxa/sharpsl_pm.c: In function
'sharpsl_pm_pxa_read_max1111':
arch/arm/mach-pxa/sharpsl_pm.c:180: warning: ISO C90 forbids mixed
declarations and code
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
(~GPLR0 & GPIO_bit(SPITZ_GPIO_KEY_INT)) | (GPLR0 &
GPIO_bit(SPITZ_GPIO_SYNC));
After using gpio_get_value, the statement should be in below.
((!gpio_get_value(SPITZ_GPIO_KEY_INT)
<< GPIO_bit(SPITZ_GPIO_KEY_INT))
| gpio_get_value(SPITZ_GPIO_SYNC));
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into depends/rmk/for-armsoc
There were conflicts between fixes going in after 3.3-rc1 and
Russell's stable arm-soc base branch. Resolving it in the dependency
branch so that each topic branch shares the same resolution.
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9g45.c
Convert all the PXA platform socket drivers to use the new irq/gpio
management provided by soc_common. This relieves these drivers from
having to do anything with these GPIOs other than provide the numbers
to soc_common.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 7cea00657d.
The sa1100 cleanups fatally broke the SA1100 RTC driver - the first
hint that something is wrong are these compiler warnings:
drivers/rtc/rtc-sa1100.c:42:1: warning: "RCNR" redefined
In file included from arch/arm/mach-sa1100/include/mach/hardware.h:73,
from drivers/rtc/rtc-sa1100.c:35:
arch/arm/mach-sa1100/include/mach/SA-1100.h:877:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:43:1: warning: "RTAR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:876:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:44:1: warning: "RTSR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:879:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:45:1: warning: "RTTR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:878:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:47:1: warning: "RTSR_HZE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:891:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:48:1: warning: "RTSR_ALE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:890:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:49:1: warning: "RTSR_HZ" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:889:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:50:1: warning: "RTSR_AL" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:888:1: warning: this is the location of the previous definition
and the second problem, which is far more severe, are the different
register layouts, resulting in the wrong registers being read on
SA11x0 platforms. This patch adds:
#define RCNR 0x00 /* RTC Count Register */
#define RTAR 0x04 /* RTC Alarm Register */
#define RTSR 0x08 /* RTC Status Register */
#define RTTR 0x0c /* RTC Timer Trim Register */
but the SA11x0 registers are:
#define RTAR __REG(0x90010000) /* RTC Alarm Reg. */
#define RCNR __REG(0x90010004) /* RTC CouNt Reg. */
#define RTTR __REG(0x90010008) /* RTC Trim Reg. */
#define RTSR __REG(0x90010010) /* RTC Status Reg. */
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lYb/
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Board-level changes
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
mioa701: add newly available DoC G3 chip
arm/tegra: remove __initdata annotation from pinmux tables
arm/tegra: Use bus notifiers to trigger pinmux setup
arm/tegra: Refactor board-*-pinmux.c to share code
arm/tegra: Fix mistake in Trimslice's pinmux
arm/tegra: Rework Seaboard-vs-Ventana pinmux table
arm/tegra: Remove useless entries from ventana_pinmux[]
arm/tegra: PCIe: Remove include of mach/pinmux.h
arm/tegra: Harmony PCIe: Don't touch pinmux
arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
arm/tegra: Split Seaboard GPIO table to allow for Ventana
ARM: imx6q: generate imx6q dtb files
arm/imx6q: Rename Sabreauto to Armadillo2
arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
arm/imx6: add imx6q sabrelite board support
dts/imx: rename uart labels to consistent with hw spec
...
Simple bug fixes that were not considered important enough for inclusion
into 3.2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUATwtcRmCrR//JCVInAQK+pQ//e2XfYJJf8LChiiESxzin74BO6fcS5FWM
P5h4fCUi1lqVmOAEfM+MIktcMIH7ThpXu/gG1/8Rh+V2uikvfPRzfsAcziphRCVV
2fPmleOpMxTzCuMc/U35lCcfRYsuoRcvbnS0BdvzqzxCCf9PDZvMF9NmRr5+/XHS
4isIC+4c7tGPMPh32RoevDoyrc4Z3UakoItZ06Ahd0eE01lz7fTt4Ztr18/fqO/V
2GKSPYpKChJXnxPGy32Qdw7tx/GY7PbG0SmDycSv/o6TogF6wSOKdKlLG5tVqv8o
pt10smaz2vizr62wG8n3ePhFjAQvq6uSDp1cyb7jaKdzri2YmRHeMUG2I0pDcqTB
KnVi0MSp0+I0AN7W8CQlKgYlbkCv8fvw4STfJfPS4Nkm31193/0psyTYTcC4luJq
bvujaKkWMZJzjNAnOqmtHK/LRTjiswSaocR7pQULOpBTP5mjhkyVbGWFOEOhEwgQ
JX69cGtj2utyxCCDjRY3V16RvyetUgLCIDf13orbFb0o0F1vecdUMa7GguL4qmqP
7p82ml4OrAHlpD4C/JlS3XdkcnUUL6IwLN8V2J8mEr31N3EcG+q+uuAMHLMo/EqT
yMRQHgcZ77GhDWuwdOxbp6CX4qY2fWvk9sRW+N6ObLnRfA++bGh2mWWAKiZgyV7/
CtbO9tWmGnE=
=UU7m
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Non-critical bug fixes
Simple bug fixes that were not considered important enough for inclusion
into 3.2.
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update pxa and mmp
ARM: pxa: Include linux/export.h in balloon3.c
ARM: OMAP4: clock: Add CPU local timer clock node
ARM: OMAP4: hwmod: Don't wait for the idle status if modulemode is not supported
ARM: OMAP: AM3517/3505: fix crash on boot due to incorrect voltagedomain data
ARM: OMAP: hwmod data: fix the panic on Nokia RM-680 during boot
ARM: OMAP2+: DMA: Workaround for invalid destination position
ARM: OMAP2+: DMA: Workaround for invalid source position
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* drivers/rtc-sa1100:
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
Now sa1100-rtc can support sa1100/pxa/mmp soc series, then we need
add dummy clock for sa1100-rtc.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since the regmap of rtc on sa1100, pxa and mmp Marvell soc families are
almost the same, so re-arch the rtc-sa1100 to support them.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As the mioa701 board has a M-Systems DiskOnChip G3 chip, add
it to the platform resources of the board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@atosorigin.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Include linux/export.h to fix below build warning:
CC arch/arm/mach-pxa/balloon3.o
arch/arm/mach-pxa/balloon3.c:85: warning: data definition has no type or storage class
arch/arm/mach-pxa/balloon3.c:85: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/mach-pxa/balloon3.c:85: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
arch/arm/mach-pxa/spitz_pm.c: In function ‘spitz_presuspend’:
arch/arm/mach-pxa/spitz_pm.c:112:2: error: implicit declaration of
function ‘GPIO_bit’
make[1]: *** [arch/arm/mach-pxa/spitz_pm.o] Error 1
GPIO_bit() is moved into <linux/gpio-pxa.h>.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
The poodle restart handler was added in 74617fb6b8 (3593/1: Add reboot
and shutdown handlers for Zaurus handhelds), and at that time it was
necessary to deal with the RCSR register. This commit also forced all
restarts to use the 'hard' restart method.
In dc38e2ad53 (pxa: Fix RCSR handling), the RCSR handling was removed,
leaving just the forcing to use a 'hard' restart. As hard restarts are
the default (in the absense of a reboot= command line argument), this
seems pointless. In any case, Richard Purdie says:
> From what I remember that hardware either always reboots or always
> halts. I think the option was therefore left hardcoded to make it clear
> it wasn't expected to work. Later Zaurii models could do either but
> required some manual poking of registers to make it happen iirc.
>
> Regardless, you can probably clean this up as you suggest now.
So, lets remove the unnecessary interception and rely on the default
restart mode.
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Krzysztof Ha■asa <khc@pm.waw.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Even when CONFIG_MULTI_IRQ_HANDLER is selected, the core code
requires the arch_irq_handler_default macro to be defined as
a fallback.
It turns out nobody is using that particular feature as both PXA
and shmobile have all their machine descriptors populated with
the interrupt handler, leaving unused code (or empty macros) in
their entry-macro.S file just to be able to compile entry-armv.S.
Make CONFIG_MULTI_IRQ_HANDLER exclusive wrt arch_irq_handler_default,
which allows to remove one test from the hot path. Also cleanup both
PXA and shmobile entry-macro.S.
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Support clk in gpio driver. There's no gpio clock in PXA25x and PXA27x.
So use dummy clk instead. And move the gpio edge initialization into
gpio driver for arch-mmp.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
NR_BUILTIN_GPIO is both defined in arch-pxa and arch-mmp. Now replace it
with PXA_NR_BUILTIN_GPIO and MMP_NR_BUILTIN_GPIO.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to define gpio_to_irq() and irq_to_gpio() for potential name
confliction since multiple architecture will be built together.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
GPIO0 and GPIO1 are linked to unique interrupt line in PXA series,
others are linked to another interrupt line. All GPIO are linked to one
interrupt line in MMP series.
Since gpio driver is shared between PXA series and MMP series, define
GPIO0 and GPIO1 as chained interrupt chip. So we can move out gpio code
from irq.c to gpio-pxa.c.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Avoid potential naming confliction since multiple architecture will be built
in a single kernel.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Add a default restart mode to reflect the hard-coded restart mode
found in these files.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since CONFIG_USB_GADGET_PXA27X and other macros are renamed to
CONFIG_USB_PXA27X. Update them in arch/arm/mach-pxa and arch/arm/configs
to keep consistent.
Cc: stable@kernel.org
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
A mismerge in 43872fa (Merge branch 'depends/rmk/gpio' into next/fixes)
causes these build errors:
In file included from arch/arm/mach-pxa/include/mach/gpio.h:30,
from arch/arm/include/asm/gpio.h:6,
from include/linux/gpio.h:31,
from arch/arm/mach-pxa/generic.c:20:
arch/arm/mach-pxa/include/mach/gpio-pxa.h: In function ■__gpio_is_occupied■:
arch/arm/mach-pxa/include/mach/gpio-pxa.h:121: error: invalid operands to binary >> (have ■void *■ and ■unsigned int■)
arch/arm/mach-pxa/include/mach/gpio-pxa.h:122: error: invalid operands to binary & (have ■void *■ and ■int■)
arch/arm/mach-pxa/include/mach/gpio-pxa.h:129: error: invalid operands to binary & (have ■void *■ and ■int■)
So fix them.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
WARNING: vmlinux.o(.text+0x1a820): Section mismatch in reference from the function eseries_register_clks() to the function .init.text:clkdev_add_table()
The function eseries_register_clks() references
the function __init clkdev_add_table().
This is often because eseries_register_clks lacks a __init
annotation or the annotation of clkdev_add_table is wrong.
by adding the __init annotation to eseries_register_clks() - this
function is only called from other __init-marked functions. While
we're here, mark it static as it's only called from within eseries.c.
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
Camera-switching GPIOs are provided by a i2c GPIO extender, switching
them can send the caller to sleep. Use the GPIO API *_cansleep methods
explicitly to avoid runtime warnings.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
Things like module_param and core_param come from the header
moduleparam.h -- these files were relying on the fact that
module.h is implicitly present everywhere and it in turn
includes the moduleparam header.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files will fail to compile if we dont clean them up in advance
and have them include the appropriate headers they need.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Arnd Bergmann
Paul Parsons
Greg Kroah-Hartman
Olof Johansson
Rob Herring
Haojian Zhuang
Haojian Zhuang
Heiko Stübner
Heikki Krogerus
Russell King
Axel Lin
Danny Kukawka
Nicolas Pitre
Linus Torvalds
Jett.Zhou
Robert Jarzmik
Marc Zyngier
Jiri Kosina
Guennadi Liakhovetski
Paul Gortmaker
Paul Bolle