The dynamic add path for PCI Host Bridges can fail to configure children
adapters under P5IOC controllers. It fails to properly fixup bus/device
resources, and it fails to properly enable EEH. Both of these steps
need to occur before any children devices are enabled in
pci_bus_add_devices().
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
remove warnings when building a 64bit kernel.
smp_call_function triggers also with 32bit kernel.
WARNING: vmlinux: duplicate symbol 'smp_call_function' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:164:EXPORT_SYMBOL(smp_call_function);
arch/powerpc/kernel/smp.c:300:EXPORT_SYMBOL(smp_call_function);
WARNING: vmlinux: duplicate symbol 'ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:113:EXPORT_SYMBOL(ioremap);
arch/powerpc/mm/pgtable_64.c:321:EXPORT_SYMBOL(ioremap);
WARNING: vmlinux: duplicate symbol '__ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:117:EXPORT_SYMBOL(__ioremap);
arch/powerpc/mm/pgtable_64.c:322:EXPORT_SYMBOL(__ioremap);
WARNING: vmlinux: duplicate symbol 'iounmap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:118:EXPORT_SYMBOL(iounmap);
arch/powerpc/mm/pgtable_64.c:323:EXPORT_SYMBOL(iounmap);
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We should be memset'ing the data we are pointing to, not the pointer
itself. This is in an error path so we probably don't hit it much.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent changes to keep gettimeofday in sync with xtime had the side
effect that it was occasionally possible for the time reported by
gettimeofday to go back by a microsecond. There were two reasons:
(1) when we recalculated the offsets used by gettimeofday every 2^31
timebase ticks, we lost an accumulated fractional microsecond, and
(2) because the update is done some time after the notional start of
jiffy, if ntp is slowing the clock, it is possible to see time go backwards
when the timebase factor gets reduced.
This fixes it by (a) slowing the gettimeofday clock by about 1us in
2^31 timebase ticks (a factor of less than 1 in 3.7 million), and (b)
adjusting the timebase offsets in the rare case that the gettimeofday
result could possibly go backwards (i.e. when ntp is slowing the clock
and the timer interrupt is late). In this case the adjustment will
reduce to zero eventually because of (a).
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current pcspkr code combines the device and driver registration.
This patch splits these, putting the device registration in the arch
specific code.
PowerPC and MIPS only have the pcspkr present sometimes.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A careful reading of the recent changes to the system call entry/exit
paths revealed several problems, plus some things that could be
simplified and improved:
* 32-bit wasn't testing the _TIF_NOERROR bit in the syscall fast exit
path, so it was only doing anything with it once it saw some other
bit being set. In other words, the noerror behaviour would apply to
the next system call where we had to reschedule or deliver a signal,
which is not necessarily the current system call.
* 32-bit wasn't doing the call to ptrace_notify in the syscall exit
path when the _TIF_SINGLESTEP bit was set.
* _TIF_RESTOREALL was in both _TIF_USER_WORK_MASK and
_TIF_PERSYSCALL_MASK, which is odd since _TIF_RESTOREALL is only set
by system calls. I took it out of _TIF_USER_WORK_MASK.
* On 64-bit, _TIF_RESTOREALL wasn't causing the non-volatile registers
to be restored (unless perhaps a signal was delivered or the syscall
was traced or single-stepped). Thus the non-volatile registers
weren't restored on exit from a signal handler. We probably got
away with it mostly because signal handlers written in C wouldn't
alter the non-volatile registers.
* On 32-bit I simplified the code and made it more like 64-bit by
making the syscall exit path jump to ret_from_except to handle
preemption and signal delivery.
* 32-bit was calling do_signal unnecessarily when _TIF_RESTOREALL was
set - but I think because of that 32-bit was actually restoring the
non-volatile registers on exit from a signal handler.
* I changed the order of enabling interrupts and saving the
non-volatile registers before calling do_syscall_trace_leave; now we
enable interrupts first.
Signed-off-by: Paul Mackerras <paulus@samba.org>
yaboot is scrogged and calls us with an invalid stack alignment,
it seems.
Thanks to David Woodhouse to pointing me to the problem.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Thu, 2006-03-02 at 19:55 +0100, Olaf Hering wrote:
> My iBook1 has 2 memory regions in reg. Depending on how I boot it
> (vmlinux+initrd) or zImage.initrd, it will not boot with current Linus
> tree.
> rmo_top should be 160MB instead of 32MB.
On logically-partitioned machines the first element of the reg
property in the memory node is defined to be the "RMO" region,
i.e. the memory that the processor can access in real mode. On other
machines the first element has no special meaning, so only take it to
be the RMO region on LPAR machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes userland aware of the icache snoop capability of the
POWER5 (and possibly others in the future) and of SMT capabilities.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 32-bit, the exception prolog for the program check exception doesn't
enable interrupts early on. If it is an illegal instruction exception,
we read the instruction in order to emulate certain instructions, and
the get_user of the instruction triggers a WARN_ON since interrupts
are still disabled. This adds a local_irq_enable() to enable
interrupts before reading the instruction.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds mm->task_size to keep track of the task size of a given mm
and uses that to fix the powerpc vdso so that it uses the mm task size to
decide what pages to fault in instead of the current thread flags (which
broke when ptracing).
(akpm: I expect that mm_struct.task_size will become the way in which we
finally sort out the confusion between 32-bit processes and 32-bit mm's. It
may need tweaks, but at this stage this patch is powerpc-only.)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bug in the assembly code of the vdso can cause gettimeofday() to hang
or to return incorrect results. The wrong register was used to test for
pending updates of the calibration variables and to create a dependency
for subsequent loads. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The inline cputime_to_foo and foo_to_cputime conversion functions in
include/asm-powerpc/cputime.h refer to 5 variables, which need to be
exported if those functions are to be usable from modules.
Signed-off-by: Paul Mackerras <paulus@samba.org>
mem= command line option was being ignored in arch/powerpc if we were not
a CONFIG_MULTIPLATFORM (which is handled via prom_init stub). The initial
command line extraction and parsing needed to be moved earlier in the boot
process and have code to actual parse mem= and do something about it.
Also, fixed a compile warning in the file.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
HMT support is currently broken and needs to be reworked to play nicely
with the SMT scheduler. Remove the bit rotten bits for the time being.
I also updated an incorrect comment, we enter __secondary_hold with the
physical cpu id in r3.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
altivec_unavailable_exception is called without setting r3... it looks like
the r3 that actually gets passed in as struct pt_regs *regs is the
undisturbed value of r3 at the time the altivec instruction was encountered.
The user actually gets to choose the pt_regs printed in the Oops!
This fixes the oops by passing the correct pt_regs pointer to
altivec_unavailable_exception.
Signed-off-by: Alan Curry <pacman@TheWorld.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The panic CPU is waiting forever due to some large timeout value if some
CPU is not responding to an IPI.
This patch fixes the problem - the maximum waiting period will be
10 seconds and then the kdump boot will go ahead.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For kexec we need to know the size of the MMU hash table.
Currently we calculate the size once in the htab code, and then twice more in
the kexec code, once using htab_hash_mask and once using ppc64_pft_size.
On some machines the ppc64_pft_size calculation is broken because
ppc64_pft_size is not set.
So we need to fix the second calculation, but better still we should just
calculate the size once and use it everywhere else.
Tested on Power5 LPAR, Power4 non-LPAR and Power3.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For UP to SMP kexec to work we need to jump into pSeries_secondary_smp_init
event on a UP + KEXEC kernel. The secondary cpus will not find their hw_cpu_id
in the paca and so they'll jump into kexec_wait, ready for a kexec.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because smp_release_cpus() is built for SMP || KEXEC, it's not safe to
unconditionally call it from setup_system(). On a UP && KEXEC kernel we'll
start up the secondary CPUs which will then go beserk and we die.
Simple fix is to conditionally call smp_release_cpus() in setup_system(). With
that in place we don't need the dummy definition of smp_release_cpus() because
all call sites are #ifdef'ed either SMP or KEXEC.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fallback gracefully when reading /proc/ppc64/lparcfg when the /rtas
device node can't be found.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few symbols are exported twice, remove them from ppc_ksyms.c
Remove users of sys_ctrler in arch/ppc/
WARNING: vmlinux: duplicate symbol '__delay' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__up' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down_interruptible' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'sys_ctrler' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncat' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncmp' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strrchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strnlen' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strpbrk' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'memscan' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strstr' previous definition was in vmlinux
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a regression which was introduced by moving ppc32 to use
the same sort of lockless gettimeofday as ppc64 has been using for
some time. This involves getting the timebase and performing some
simple arithmetic to convert it to seconds and microseconds. However,
the factor and offset used there weren't being updated when NTP
varied the tick length using adjtimex. 64-bit didn't notice the
problem because it had a hook in the 32-bit adjtimex compat routine
that attempted to work out what the generic timekeeping code would
do and alter the factor and offset to match. However, that code
was very complex and it wasn't clear that it still matched what the
generic code would do.
Now we use the generic current_tick_length() routine that was recently
added to check that the current tick will be as long as we expect; if
not we recompute the factor and offset. This keeps gettimeofday and
xtime in sync. In addition we check that gettimeofday hasn't got ahead
of xtime on each timer interrupt; if it has, we resync.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we have some stuff in firmware.h and kernel/firmware.c that is
#ifdef CONFIG_PPC_PSERIES. Move it all into platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The e500 core reference manual indicates that isync is required
after mtmsr(DE bit) and mtspr DBCR0. Add isyncs to make the code
conform to the spec.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated FP unavailable exception to refer to the correct
function in traps.c. head_booke.h was using the old name, KernelFP,
instead of kernel_fp_unavailable_exception.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Registers system call for the powerpc architecture.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With this, new system calls only have to be wired up in one place
for ARCH=ppc and ARCH=powerpc, rather than 2.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently most callers of lmb_alloc() don't check if it worked or not, if it
ever does weird bad things will probably happen. The few callers who do check
just panic or BUG_ON.
So make lmb_alloc() panic internally, to catch bugs at the source. The few
callers who did check the result no longer need to.
The only caller that did anything interesting with the return result was
careful_allocation(). For it we create __lmb_alloc_base() which _doesn't_ panic
automatically, a little messy, but passable.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
remove extern declarations of pmac_newworld
move pmac_newworld to bss
if there is any "interrupt-controller" device, then it is newworld.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a cpu is hotplug-onlined, if we don't set per_cpu(last_jiffy) to
something sane, timer_interrupt will execute its while loop for every
tick missed since the cpu was last online (or since the system was
booted, if we're adding a new cpu). This can cause weird hangs, ssh
sessions dropping, and we can even go xmon if we take a global IPI at
the wrong time.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since 404849bbd2 we've been using
LOAD_REG_ADDRBASE, which uses the toc pointer, in decrementer_iSeries_masked.
This can explode if we take the decrementer interrupt while we're in a module,
because the toc pointer in r2 will be the module's toc pointer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Checking a pointer for NULL before passing it to kfree is pointless, kfree
does its own NULL checking of input.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/kernel/udbg_16550.c: In function `udbg_init_maple_realmode':
arch/powerpc/kernel/udbg_16550.c:162: warning: assignment from incompatible pointer type
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's possible for prom_init to allocate the flat device tree inside the
kdump crash kernel region. If this happens, when we load the kdump kernel we
overwrite the flattened device tree, which is bad.
We could make prom_init try and avoid allocating inside the crash kernel
region, but then we run into issues if the crash kernel region uses all the
space inside the RMO. The easiest solution is to move the flat device tree
once we're running in the kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It turns out that we can't stop the watchdog from
triggering here. If we touch the timer (which just uses the current jiffie
value) before we enable interrupts, it does nothing because jiffies
are not mass-updated until after we enable interrupts. If we touch the
timer after we enable interrupts, its too late because the softlockup
watchdog will already have triggered. The touch_softlockup_watchdog
call removed below does nothing.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to prod everyone here since this is the only CPU that is
guaranteed to be running after the ibm,suspend-me RTAS call returns.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Correctly return the status from the RTAS call. rtas_call expects
to return the status as a return value.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/kernel/rtas.c is getting hvcall.h via spinlock.h, but when we're
building for UP we don't include spinlock.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This addresses two items, which are unlikely to be hit if we
trust drivers.
The first is moving a memory barrier below where the vmerged SG count
is passed back, but before the list is set to end. If those
instructions were reordered, there could be an issue in iommu_unmap_sg().
The second is making sure we terminate the list on the failure case of
iommu_map_sg(). If a driver does not look at the failure return code,
it could pass a ill-formed SG list to iommu_unmap_sg().
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
You can't boot a kdump kernel via OF, not reliably anyway, the kernel being at
32 MB conflicts with the zImage wrapper etc. and it blows up.
It's trivial to check in prom_init though, and this is early enough that we can
actually drop back to OF where a reset-all will get you going again, which is
kinda nice. I think this should go in for 2.6.16.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In prom.c we run finish_node() on allnodes twice. The first time we just
calculate how much memory we'll need, the second time we do the actual work.
If the calculation stage determines that we need 0 bytes, then we should skip
the lmb allocation. Although an alloc of zero will work, it has been seen to
lead to a BUG_ON() in reserve_bootmem() on at least one machine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When loading up the FPU, we were using a 'ld' (load doubleword)
instruction to get the FP exception mode from the thread_struct,
but it's only an int field. This changes the ld to lwz (load
word and zero-extend).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Better save the sigmask instead of throwing it away so it can be restored.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Older pSeries systems with serial ports dont get any console output after
recent changes. CONFIG_ISA does not make sense for CONFIG_PPC_PSERIES
because it enables lots of old drivers. Instead, remove the dependency on
CONFIG_ISA from the serial port discovery code.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement the TIF_RESTORE_SIGMASK flag in the new arch/powerpc kernel, for
both 32-bit and 64-bit system call paths.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TIF_RESTORE_SIGMASK flag allows us to have a generic implementation of
sys_rt_sigsuspend() instead of duplicating it for each architecture. This
provides such an implementation and makes arch/powerpc use it.
It also tidies up the ppc32 sys_sigsuspend() to use TIF_RESTORE_SIGMASK.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When I removed the powermac support from arch/ppc/kernel/pci.c,
I overlooked the fact that that file is used in 32-bit ARCH=powerpc
builds. To prevent problems in future, restore the original version
of that file as arch/powerpc/kernel/pci_32.c, and use that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
- This contains the arch specific changes for the following the
kdump generic fixes which were already accepted in the upstream.
. Capturing CPU registers (for the case of 'panic' and invoking
the dump using 'sysrq-trigger') from a function (stack frame) which will
be not be available during the kdump boot. Hence, might result in
invalid stack trace.
. Dynamically allocating per cpu ELF notes section instead of
statically for NR_CPUS.
- Fix the compiler warning in prom_init.c.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The first generation of PCI powermacs had a host bridge called /chaos
which was for all intents and purposes a PCI host bridge, but has a
device_type of "vci" in the device tree (presumably it's not really
PCI at the hardware level or something).
The OF parsing stuff in arch/powerpc/kernel/prom_parse.c currently
doesn't recognize it as a PCI bridge, which means that controlfb.c
can't get its device addresses.
This makes prom_parse.c recognize a device_type of "vci" as indicating
a PCI host bridge. With this, controlfb works again.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handle the ibm,suspend-me RTAS call specially. It needs
to be wrapped in a set of synchronization hypervisor calls
(H_Join). When the H_Join calls are made on all CPUs, the
intent is that only one will return with H_Continue, meaning
that he is the "last man standing". That CPU then issues the
ibm,suspend-me call. What is interesting, of course, is that
the CPU running when the rtas syscall is made, may NOT be the
CPU that ultimately executes the ibm,suspend-me rtas call.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the first MPC83xx board that uses a flat device tree to arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On a number of embedded reference boards there isn't always a
way to reset, power_off, or halt the board. Rather than having
each board implement a spin loop just let the generic code do
it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In 2.6.15-git6 a change was commited in the oprofile support in
the powerpc architecture. It introduced the powerpc_oprofile_type
which contains the define G4. This causes a name clash with the
existing wacom usb tablet driver.
CC [M] drivers/usb/input/wacom.o
drivers/usb/input/wacom.c:98: error: conflicting types for `G4'
include/asm/cputable.h:37: error: previous declaration of `G4'
CC [M] drivers/usb/mon/mon_text.o
make[3]: *** [drivers/usb/input/wacom.o] Error 1
make[2]: *** [drivers/usb/input] Error 2
The elements of an enum declared in global scope are effectivly
global identifiers themselves. As such we need to ensure the names
are unique. This patch updates the later oprofile support to use
unique names.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The glibc folks want to use AT_PLATFORM to select between possible
alternative versions of shared libraries. This commit makes the kernel
supply an AT_PLATFORM string that indicates what class of processor
we are running on. Processors with the same set of user-level
instructions and roughly the same instruction scheduling characteristics
are given the same AT_PLATFORM value; for example, 821, 823 and 860
are all reported as "ppc823", and 7447, 7447A, 7448, 7450, 7451, 7455
are all called "ppc7450".
The intention is that the AT_PLATFORM values match the values that
gcc accepts for the -mcpu= option. For values which are numeric
(e.g. -mcpu=750), "ppc" has been prepended.
This also adds a PPC_FEATURE_BOOKE bit to the AT_HWCAP value and sets
it for the 440 family and the Freescale 85xx family.
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present the lppaca - the structure shared with the iSeries
hypervisor and phyp - is contained within the PACA, our own low-level
per-cpu structure. This doesn't have to be so, the patch below
removes it, making a separate array of lppaca structures.
This saves approximately 500*NR_CPUS bytes of image size and kernel
memory, because we don't need aligning gap between the Linux and
hypervisor portions of every PACA. On the other hand it means an
extra level of dereference in many accesses to the lppaca.
The patch also gets rid of several places where we assign the paca
address to a local variable for no particular reason.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates the variety of macros used for loading 32 or
64-bit constants in assembler (LOADADDR, LOADBASE, SET_REG_TO_*). The
idea is to make the set of macros consistent across 32 and 64 bit and
to make it more obvious which is the appropriate one to use in a given
situation. The new macros and their semantics are described in the
comments in ppc_asm.h.
In the process, we change several places that were unnecessarily using
immediate loads on ppc64 to use the GOT/TOC. Likewise we cleanup a
couple of places where we were clumsily subtracting PAGE_OFFSET with
asm instructions to use assemble-time arithmetic or the toreal() macro
instead.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add an of_find_property function that returns a struct property
given a property name. Then change the get_property function to
use that routine internally.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for updating and removing device tree
properties. Since we hand out pointers to properties with gay
abandon, we can't just free the property storage. Instead we
move deleted, or the old copy of an updated property, to a
"dead properties" list.
Also note, its not feasable to kref device tree properties.
we call get_property() all over the kernel in a wild variety
of contexts.
One consequence of this change is that we now take a
read_lock(&devtree_lock) when doing get_property().
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 5388fb1025 made signal_32.c
use discard_lazy_cpu_state, which broke ARCH=ppc because that
uses the common signal_32.c but has its own process.c. Make ARCH=ppc
use the common process.c to fix this and to reduce the amount
of duplicated code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
pcibios_claim_one_bus is not needed on iSeries and phbs_remap_io can be
mode static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Fixed memory reserve map layout
The memory reserve map is suppose to be a pair of 64-bit integers
to represent each region. On ppc32 the code was treating the
pair as two 32-bit integers. Additional the prom_init code was
producing the wrong layout on ppc32.
Added a simple check to try to provide backwards compatibility.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Heikki Lindholm pointed out that there was a potential race with the
lazy CPU state (FP, VR, EVR) stuff if preempt is enabled. The race
is that in the process of restoring FP state on sigreturn, the task
gets preempted by a user task that wants to use the FPU. It will take
an FP unavailable exception, which will write the current FPU state
to the thread_struct, overwriting the values which sigreturn has
stored. Note that this can only happen on UP since we don't implement
lazy CPU state on SMP.
The fix is to flush the lazy CPU state before updating the
thread_struct. To do this we re-use the flush_lazy_cpu_state()
function from process.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window where a probe gets removed right after the probe is hit
on some different cpu. In this case probe handlers can't find a matching
probe instance related to break address. In this case we need to read the
original instruction at break address to see if that is not a break/int3
instruction and recover safely.
Previous code had a bug where we were not checking for the above race in
case of reentrant probes and the below patch fixes this race.
Tested on IA64, Powerpc, x86_64.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/powerpc/kernel/crash.c isn't safe for PPC32 (yet?), so don't build it.
Built with CONFIG_KEXEC=y for pmac32_defconfig, pseries_defconfig,
and g5_defconfig.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the compilation error (shown below) when CONFIG_SMP=n.
arch/powerpc/kernel/crash.c: In function `crash_kexec_prepare_cpus':
arch/powerpc/kernel/crash.c:236: error: implicit declaration of
function `smp_release_cpus'
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current ppc64 per cpu data implementation is quite slow. eg:
lhz 11,18(13) /* smp_processor_id() */
ld 9,.LC63-.LCTOC1(30) /* per_cpu__variable_name */
ld 8,.LC61-.LCTOC1(30) /* __per_cpu_offset */
sldi 11,11,3 /* form index into __per_cpu_offset */
mr 10,9
ldx 9,11,8 /* __per_cpu_offset[smp_processor_id()] */
ldx 0,10,9 /* load per cpu data */
5 loads for something that is supposed to be fast, pretty awful. One
reason for the large number of loads is that we have to synthesize 2
64bit constants (per_cpu__variable_name and __per_cpu_offset).
By putting __per_cpu_offset into the paca we can avoid the 2 loads
associated with it:
ld 11,56(13) /* paca->data_offset */
ld 9,.LC59-.LCTOC1(30) /* per_cpu__variable_name */
ldx 0,9,11 /* load per cpu data
Longer term we can should be able to do even better than 3 loads.
If per_cpu__variable_name wasnt a 64bit constant and paca->data_offset
was in a register we could cut it down to one load. A suggestion from
Rusty is to use gcc's __thread extension here. In order to do this we
would need to free up r13 (the __thread register and where the paca
currently is). So far Ive had a few unsuccessful attempts at doing that :)
The patch also allocates per cpu memory node local on NUMA machines.
This patch from Rusty has been sitting in my queue _forever_ but stalled
when I hit the compiler bug. Sorry about that.
Finally I also only allocate per cpu data for possible cpus, which comes
straight out of the x86-64 port. On a pseries kernel (with NR_CPUS == 128)
and 4 possible cpus we see some nice gains:
total used free shared buffers cached
Mem: 4012228 212860 3799368 0 0 162424
total used free shared buffers cached
Mem: 4016200 212984 3803216 0 0 162424
A saving of 3.75MB. Quite nice for smaller machines. Note: we now have
to be careful of per cpu users that touch data for !possible cpus.
At this stage it might be worth making the NUMA and possible cpu
optimisations generic, but per cpu init is done so early we have to be
careful that all architectures have their possible map setup correctly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds Kconfig entries to control the early debugging options,
currently in setup_64.c.
Doing this via Kconfig rather than #defines means you can have one source tree,
which is buildable for multiple platforms - and you can enable the correct
early debug option for each platform via .config.
I made udbg_early_init() a static inline because otherwise GCC is to daft to
optimise it away when debugging is off.
Now that we have udbg_init_rtas() we can make call_rtas_display_status* static.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Connect iSeries up to the standard early debugging infrastructure.
To actually use this you need to enable the iSeries early debugging
in setup_64.c. Then after the messages are logged hit Ctrl-x Ctrl-x on
your console to dump the Hypervisor console buffer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RPAPHP hoplug driver will not build as a module, because it calls
on a pcibios routine which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch (against 2.6.15-rc5-mm3) fixes a kprobes build break
due to changes introduced in the kprobe locking in 2.6.15-rc5-mm3. In
addition, the patch reverts back the open-coding of kprobe_mutex.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on some feedback from Oleg Nesterov, I have made few changes to
previously posted patch.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>