Following problems are addressed:
- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
is a relict of the abandoned support for interrupted
erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations
Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Patch from Andrew Victor
This patch removes some now unnecessary global variables -
at91_master_clock, at91_serial_map, at91_console_port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Update s3c2410_defconfig to latest kernel with the
latest patches
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This final patch includes some general fixes.
1. Link in pm.o if CONFIG_PM is enabled. [Should have been included in
patch 3605/1].
2. Use __raw_readl()/__raw_writel() when accessing System Peripheral
registers.
3. Removed some unnecessary includes
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the core Power Management support for the AT91RM9200
processor. It will support suspend-to-RAM and standby modes.
The suspend-to-RAM functionality is not 100% complete. The code that
needs to be execute from the internal SRAM to restore the system is
outstanding. For now we just fall through to Standby mode.
The AT91-specific at91_suspend_entering_slow_clock() function will
eventually be replaced by clk_must_disable() once that functionality is
added to mainline clock API.
Patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch removes the now unnecessary
include/asm-arm/arch-at91rm9200/pio.h file. The pin configuration is
now handled in the platform-device setup code
(arch/arm/mach-at91rm9200/devices.c).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Liam Girdwood
This patch adds some new PXA27x SSP port registers and also fixes the
SSP slots per frame macro
Changes:-
o SSCR0_SlotPerFrm fixed
o Added SSP port TSA, RSA, TSS and ACD registers
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Fix two typos in include/asm-arm/arch-ixp23xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NIPQUAD expects an l-value of type __be32, _NOT_ a pointer to __be32.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof(pointer) != sizeof(array)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
I was doing some testing and noticed that when the audit system was disabled,
I was still getting messages about the loginuid being set. The following patch
makes audit_set_loginuid look at in_syscall to determine if it should create
an audit event. The loginuid will continue to be set as long as there is a context.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Clear AUDIT_FILTER_PREPEND flag after adding rule to list. This
fixes three problems when a rule is added with the -A syntax:
- auditctl displays filter list as "(null)"
- the rule cannot be removed using -d
- a duplicate rule can be added with -a
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In this implementation, audit registers inotify watches on the parent
directories of paths specified in audit rules. When audit's inotify
event handler is called, it updates any affected rules based on the
filesystem event. If the parent directory is renamed, removed, or its
filesystem is unmounted, audit removes all rules referencing that
inotify watch.
To keep things simple, this implementation limits location-based
auditing to the directory entries in an existing directory. Given
a path-based rule for /foo/bar/passwd, the following table applies:
passwd modified -- audit event logged
passwd replaced -- audit event logged, rules list updated
bar renamed -- rule removed
foo renamed -- untracked, meaning that the rule now applies to
the new location
Audit users typically want to have many rules referencing filesystem
objects, which can significantly impact filtering performance. This
patch also adds an inode-number-based rule hash to mitigate this
situation.
The patch is relative to the audit git tree:
http://kernel.org/git/?p=linux/kernel/git/viro/audit-current.git;a=summary
and uses the inotify kernel API:
http://lkml.org/lkml/2006/6/1/145
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch adds audit support to POSIX message queues. It applies cleanly to
the lspp.b15 branch of Al Viro's git tree. There are new auxiliary data
structures, and collection and emission routines in kernel/auditsc.c. New hooks
in ipc/mqueue.c collect arguments from the syscalls.
I tested the patch by building the examples from the POSIX MQ library tarball.
Build them -lrt, not against the old MQ library in the tarball. Here's the URL:
http://www.geocities.com/wronski12/posix_ipc/libmqueue-4.41.tar.gz
Do auditctl -a exit,always -S for mq_open, mq_timedsend, mq_timedreceive,
mq_notify, mq_getsetattr. mq_unlink has no new hooks. Please see the
corresponding userspace patch to get correct output from auditd for the new
record types.
[fixes folded]
Signed-off-by: George Wilson <ltcgcw@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix a broken comparison that causes the process clearance to be checked for
both se_clr and se_sen audit filters.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The following patch addresses most of the issues with the IPC_SET_PERM
records as described in:
https://www.redhat.com/archives/linux-audit/2006-May/msg00010.html
and addresses the comments I received on the record field names.
To summarize, I made the following changes:
1. Changed sys_msgctl() and semctl_down() so that an IPC_SET_PERM
record is emitted in the failure case as well as the success case.
This matches the behavior in sys_shmctl(). I could simplify the
code in sys_msgctl() and semctl_down() slightly but it would mean
that in some error cases we could get an IPC_SET_PERM record
without an IPC record and that seemed odd.
2. No change to the IPC record type, given no feedback on the backward
compatibility question.
3. Removed the qbytes field from the IPC record. It wasn't being
set and when audit_ipc_obj() is called from ipcperms(), the
information isn't available. If we want the information in the IPC
record, more extensive changes will be necessary. Since it only
applies to message queues and it isn't really permission related, it
doesn't seem worth it.
4. Removed the obj field from the IPC_SET_PERM record. This means that
the kern_ipc_perm argument is no longer needed.
5. Removed the spaces and renamed the IPC_SET_PERM field names. Replaced iuid and
igid fields with ouid and ogid in the IPC record.
I tested this with the lspp.22 kernel on an x86_64 box. I believe it
applies cleanly on the latest kernel.
-- ljk
Signed-off-by: Linda Knippers <linda.knippers@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Just a few minor proposed updates. Only the last one will
actually affect behavior. The rest are just misleading
code.
Several AUDIT_SET functions return 'old' value, but only
return value <0 is checked for. So just return 0.
propagate audit_set_rate_limit and audit_set_backlog_limit
error values
In audit_buffer_free, the audit_freelist_count was being
incremented even when we discard the return buffer, so
audit_freelist_count can end up wrong. This could cause
the actual freelist to shrink over time, eventually
threatening to degrate audit performance.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Don't return -ENOMEM when callers of these functions are checking for
a NULL return. Bug noticed by Serge Hallyn.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We should not send a pile of replies while holding audit_netlink_mutex
since we hold the same mutex when we receive commands. As the result,
we can get blocked while sending and sit there holding the mutex while
auditctl is unable to send the next command and get around to receiving
what we'd sent.
Solution: create skb and put them into a queue instead of sending;
once we are done, send what we've got on the list. The former can
be done synchronously while we are handling AUDIT_LIST or AUDIT_LIST_RULES;
we are holding audit_netlink_mutex at that point. The latter is done
asynchronously and without messing with audit_netlink_mutex.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Update kernel documentation to include a description of the inotify
kernel API.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Acked-by: Robert Love <rml@novell.com>
Acked-by: John McCutchan <john@johnmccutchan.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allow callers to remove watches from their event handler via
inotify_remove_watch_locked(). This functionality can be used to
achieve IN_ONESHOT-like functionality for a subset of events in the
mask.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Acked-by: Robert Love <rml@novell.com>
Acked-by: John McCutchan <john@johnmccutchan.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add inotify_init_watch() so caller can use inotify_watch refcounts
before calling inotify_add_watch().
Add inotify_find_watch() to find an existing watch for an (ih,inode)
pair. This is similar to inotify_find_update_watch(), but does not
update the watch's mask if one is found.
Add inotify_rm_watch() to remove a watch via the watch pointer instead
of the watch descriptor.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Acked-by: Robert Love <rml@novell.com>
Acked-by: John McCutchan <john@johnmccutchan.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When an inotify event includes a dentry name, also include the inode
associated with that name.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Acked-by: Robert Love <rml@novell.com>
Acked-by: John McCutchan <john@johnmccutchan.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The following series of patches introduces a kernel API for inotify,
making it possible for kernel modules to benefit from inotify's
mechanism for watching inodes. With these patches, inotify will
maintain for each caller a list of watches (via an embedded struct
inotify_watch), where each inotify_watch is associated with a
corresponding struct inode. The caller registers an event handler and
specifies for which filesystem events their event handler should be
called per inotify_watch.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Acked-by: Robert Love <rml@novell.com>
Acked-by: John McCutchan <john@johnmccutchan.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This is the long overdue conversion of sparc64 over to
the generic IRQ layer.
The kernel image is slightly larger, but the BSS is ~60K
smaller due to the reduced size of struct ino_bucket.
A lot of IRQ implementation details, including ino_bucket,
were moved out of asm-sparc64/irq.h and are now private to
arch/sparc64/kernel/irq.c, and most of the code in irq.c
totally disappeared.
One thing that's different at the moment is IRQ distribution,
we do it at enable_irq() time. If the cpu mask is ALL then
we round-robin using a global rotating cpu counter, else
we pick the first cpu in the mask to support single cpu
targetting. This is similar to what powerpc's XICS IRQ
support code does.
This works fine on my UP SB1000, and the SMP build goes
fine and runs on that machine, but lots of testing on
different setups is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by PowerPC XICS interrupt support code.
All IRQs are virtualized in order to keep NR_IRQS from needing
to be too large. Interrupts on sparc64 are arbitrary 11-bit
values, but we don't need to define NR_IRQS to 2048 if we
virtualize the IRQs.
As PCI and SBUS controller drivers build device IRQs, we divy
out virtual IRQ numbers incrementally starting at 1. Zero is
a special virtual IRQ used for the timer interrupt.
So device drivers all see virtual IRQs, and all the normal
interfaces such as request_irq(), enable_irq(), etc. translate
that into a real IRQ number in order to configure the IRQ.
At this point knowledge of the struct ino_bucket is almost
entirely contained within arch/sparc64/kernel/irq.c There are
a few small bits in the PCI controller drivers that need to
be swept away before we can remove ino_bucket's definition
out of asm-sparc64/irq.h and privately into kernel/irq.c
Signed-off-by: David S. Miller <davem@davemloft.net>
And reuse that struct member for virt_irq, which will
be used in future changesets for the implementation of
mapping between real and virtual IRQ numbers.
This nicely kills off a ton of SBUS and PCI controller
PIL assignment code which is no longer necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only pil0_dummy_bucket had a pil of zero and we just killed that
off, so we can delete all special case code that used bp->pil==0
as a way to identify a dummy bucket.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first in a series of cleanups that will hopefully
allow a seamless attempt at using the generic IRQ handling
infrastructure in the Linux kernel.
Define PIL_DEVICE_IRQ and vector all device interrupts through
there.
Get rid of the ugly pil0_dummy_{bucket,desc}, instead vector
the timer interrupt directly to a specific handler since the
timer interrupt is the only event that will be signaled on
PIL 14.
The irq_worklist is now in the per-cpu trap_block[].
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of the end address when flushing iotlb entries to
ram. This bug has been a cause of esp dma errors, and it affects
HyperSPARC systems much worse than SuperSPARC systems.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner