We normally trust and use the CDC functional descriptors provided by a
number of devices. But some of these will erroneously list the address
reserved for the device end of the link. Attempting to use this on
both the device and host side will naturally not work.
Work around this bug by ignoring the functional descriptor and assign a
random address instead in this case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received packets are sometimes addressed to 00:a0:c6:00:00:00
instead of the address the device firmware should have learned
from the host:
321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request id=0x4025, seq=64/16384, ttl=64
0000 82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00 .....g.....g..E.
0010 00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a .T..@.@.W.M.U..z
0020 ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00 ....b.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply id=0x4025, seq=64/16384, ttl=55
0000 00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00 .......P......E.
0010 00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10 .T.V..7..v.z..M.
0020 55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00 U...j.@%.@..nQ..
0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k.............
0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$%
0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345
0060 36 37 67
The bogus address is always the same, and matches the address
suggested by many devices as a default address. It is likely a
hardcoded firmware default.
The circumstances where this bug has been observed indicates that
the trigger is related to timing or some other factor the host
cannot control. Repeating the exact same configuration sequence
that caused it to trigger once, will not necessarily cause it to
trigger the next time. Reproducing the bug is therefore difficult.
This opens up a possibility that the bug is more common than we can
confirm, because affected devices often will work properly again
after a reset. A procedure most users are likely to try out before
reporting a bug.
Unconditionally rewriting the destination address if the first digit
of the received packet is 0, is considered an acceptable compromise
since we already have to inspect this digit. The simplification will
cause unnecessary rewrites if the real address starts with 0, but this
is still better than adding additional tests for this particular case.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of LTE devices from different vendors all suffer from the
same firmware bug: Most of the packets received from the device while
it is attached to a LTE network will not have an ethernet header. The
devices work as expected when attached to 2G or 3G networks, sending
an ethernet header with all packets.
This driver is not aware of which network the modem attached to, and
even if it were there are still some packet types which are always
received with the header intact.
All devices supported by this driver have severely limited
networking capabilities:
- can only transmit IPv4, IPv6 and possibly ARP
- can only support a single host hardware address at any time
- will only do point-to-point communcation with the host
Because of this, we are able to reliably identify any bogus raw IP
packets by simply looking at the 4 IP version bits. All we need to
do is to avoid 4 or 6 in the first digit of the mac address. This
workaround ensures this, and fix up the received packets as necessary.
Given the distribution of the bug, it is believed that the source is
the chipset vendor. The devices which are verified to be affected are:
Huawei E392u-12 (Qualcomm MDM9200)
Pantech UML290 (Qualcomm MDM9600)
Novatel USB551L (Qualcomm MDM9600)
Novatel E362 (Qualcomm MDM9600)
It is believed that the bug depend on firmware revision, which means
that possibly all devices based on the above mentioned chipset may be
affected if we consider all available firmware revisions.
The information about affected devices and versions is likely
incomplete. As the additional overhead for packets not needing this
fixup is very small, it is considered acceptable to apply the
workaround to all devices handled by this driver.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intention was to test against the constant, not the size of
the constant.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bd329e1 ("net: cdc_ncm: do not bind to NCM compatible MBIM devices")
introduced a new policy, preferring MBIM for dual NCM/MBIM functions if
the cdc_mbim driver was enabled. This caused a regression for users
wanting to use NCM.
Devices implementing NCM backwards compatibility according to section
3.2 of the MBIM v1.0 specification allow either NCM or MBIM on a single
USB function, using different altsettings. The cdc_ncm and cdc_mbim
drivers will both probe such functions, and must agree on a common
policy for selecting either MBIM or NCM. Until now, this policy has
been set at build time based on CONFIG_USB_NET_CDC_MBIM.
Use a module parameter to set the system policy at runtime, allowing the
user to prefer NCM on systems with the cdc_mbim driver.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Reported-by: Geir Haatveit <nospam@haatveit.nu>
Reported-by: Tommi Kyntola <kynde@ts.ray.fi>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54791
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig file help information incorrectly mentions that the
SMSC LAN75xx config option is for SMSC LAN95xx devices.
Signed-off-by: Robert de Vries <rhdv@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bd877e4 ("net: qmi_wwan: use a single bind function for
all device types") made Gobi 1K devices fail probing.
Using the number of endpoints in the default altsetting to decide
whether the function use one or two interfaces is wrong. Other
altsettings may provide more endpoints.
With Gobi 1K devices, USB interface #3's altsetting is 0 by default, but
altsetting 0 only provides one interrupt endpoint and is not sufficent
for QMI. Altsetting 1 provides all 3 endpoints required for qmi_wwan
and works with QMI. Gobi 1K layout for intf#3 is:
Interface Descriptor: 255/255/255
bInterfaceNumber 3
bAlternateSetting 0
Endpoint Descriptor: Interrupt IN
Interface Descriptor: 255/255/255
bInterfaceNumber 3
bAlternateSetting 1
Endpoint Descriptor: Interrupt IN
Endpoint Descriptor: Bulk IN
Endpoint Descriptor: Bulk OUT
Prior to commit bd877e4, we would call usbnet_get_endpoints
before giving up finding enough endpoints. Removing the early
endpoint number test and the strict functional descriptor
requirement allow qmi_wwan_bind to continue until
usbnet_get_endpoints has made the final attempt to collect
endpoints. This restores the behaviour from before commit
bd877e4 without losing the added benefit of using a single bind
function.
The driver has always required a CDC Union functional descriptor
for two-interface functions. Using the existence of this
descriptor to detect two-interface functions is the logically
correct method.
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a resubmission.
Added kfree() in ax88179_get_eeprom to prevent memory leakage.
Modified "__le16 rxctl" to "u16 rxctl" in "struct ax88179_data" and removed pointless casts.
Removed asix_init and asix_exit functions and added "module_usb_driver(ax88179_178a_driver)".
Fixed endianness issue on big endian systems and verified this driver on iBook G4.
Removed steps that change net->features in ax88179_set_features function.
Added "const" to ethtool_ops structure and fixed the coding style of AX88179_BULKIN_SIZE array.
Fixed the issue that the default MTU is not 1500.
Added ax88179_change_mtu function and enabled the hardware jumbo frame function to support an
MTU higher than 1500.
Fixed indentation and empty line coding style errors.
The _nopm version usb functions were added to access register in suspend and resume functions.
Serveral variables allocted dynamically were removed and replaced by stack variables.
ax88179_get_eeprom were modified from asix_get_eeprom in asix_common.
This patch adds a driver for ASIX's AX88179 family of USB 3.0/2.0
to gigabit ethernet adapters. It's based on the AX88xxx driver but
the usb commands used to access registers for AX88179 are completely different.
This driver had been verified on x86 system with AX88179/AX88178A and
Sitcomm LN-032 USB dongles.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This USB ethernet adapter was purchased in anodyne packaging
from the computer store adjacent to linux.conf.au 2013 in
Canberra (Australia). A web search shows other recent
purchasers in Lancaster (UK) and Seattle (USA). Just like an
emergent virus, our age of e-commerce and airmail allows
underdocumented hardware to spread around the world instantly
using the vector of ridiculously low prices.
Paige Thompson, infected via eBay, discovered that the HG20F9
is a copy of the Asix 88772B; many viruses copy the RNA of
other viruses. See Paige's work at
<https://github.com/paigeadele/HG20F9>.
This patch uses her discovery to update the restructured Asix
driver in the current kernel.
Just as some viruses inhabit seemingly-healthy cells, the
HG20F9 uses the Vendor ID 0x066b assigned to Linksys Inc.
For the present there is no clash of Product ID 0x20f9.
Signed-off-by: Glen Turner <gdt@gdt.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tag all Huawei NCM devices as WWAN modems, as we don't know of any which
are not. This is necessary for userspace clients to know that the device
requires further setup on e.g. an AT-capable serial ports before
connectivity is available.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) ping_err() ICMP error handler looks at wrong ICMP header, from Li
Wei.
2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet.
3) netif_set_xps_queue() forgets to drop mutex on errors, fix from
Alexander Duyck.
4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix
from Eric Dumazet.
5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the
amount of TCP option space was not taken into account properly in
this code path. Fix from yuchung Cheng.
6) MLX4 driver allocates device queues with the wrong size, from Kleber
Sacilotto.
7) sock_diag can access past the end of the sock_diag_handlers[] array,
from Mathias Krause.
8) vlan_set_encap_proto() makes incorrect assumptions about where
skb->data points, rework the logic so that it works regardless of
where skb->data happens to be. From Jesse Gross.
9) Fix gianfar build failure with NET_POLL enabled, from Paul
Gortmaker.
10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from
Pravin B Shelar.
11) bgmac driver does:
int i;
for (i = 0; ...; ...) {
...
for (i = 0; ...; ...) {
effectively corrupting the outer loop index, use a seperate
variable for the inner loops. From Rafał Miłecki.
12) Fix suspend bugs in smsc95xx driver, from Ming Lei.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
usbnet: smsc95xx: fix broken runtime suspend
usbnet: smsc95xx: fix suspend failure
bgmac: fix indexing of 2nd level loops
b43: Fix lockdep splat on module unload
Revert "ip_gre: propogate target device GSO capability to the tunnel device"
IP_GRE: Fix GRE_CSUM case.
VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification.
IP_GRE: Fix IP-Identification.
net/pasemi: Fix missing coding style
vmxnet3: fix ethtool ring buffer size setting
vmxnet3: make local function static
bnx2x: remove dead code and make local funcs static
gianfar: fix compile fail for NET_POLL=y due to struct packing
vlan: adjust vlan_set_encap_proto() for its callers
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
vxlan: remove depends on CONFIG_EXPERIMENTAL
mlx4_en: fix allocation of CPU affinity reverse-map
mlx4_en: fix allocation of device tx_cq
...
The name of FEATURE_AUTOSUSPEND is very misleading and the actual
meaning is remote wakeup, but a device incapable of remote wakeup
still can support USB autosuspend under some situations, so rename
it to avoid misunderstanding.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b2d4b150(smsc95xx: enable dynamic autosuspend) implements
autosuspend, but breaks current runtime suspend, such as:
when the interface becomes down, the usb device can't be put into
runtime suspend any more.
This patch fixes the broken runtime suspend.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The three below functions:
smsc95xx_enter_suspend0()
smsc95xx_enter_suspend1()
smsc95xx_enter_suspend2()
return > 0 in case of success, so they will cause smsc95xx_suspend()
to return > 0 and cause suspend failure.
The bug is introduced in commit 3b9f7d(smsc95xx: fix error handling
in suspend failure case).
Cc: <stable@vger.kernel.org> [3.8]
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
It advertises a standard CDC-ETHER interface, which actually should be
driven by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bd329e1 ("net: cdc_ncm: do not bind to NCM compatible MBIM devices")
added a test for a CDC MBIM altsetting, implementing the cdc_ncm part of
MBIM backward compatibility support. This intentionally made the driver
behave differently for CDC NCM devices with 2 alternate settings for the
Communication interface, depending on whether or not CONFIG_USB_NET_CDC_MBIM
was enabled. This is correct iff alternate setting #1 really *is* a MBIM
setting. If not, then NCM probing will use a different altsetting than before,
possibly causing probing failures depending on CONFIG_USB_NET_CDC_MBIM.
Fix by setting the altsetting back to default after the test, restoring the
previous behaviour for non MBIM devices.
This bug causes probing of Huawei E3276 devices to fail when the MBIM driver
is enabled, because these devices have a second alternate setting with no CDC
functional descriptors.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Reported-and-tested-by: Jonathan A. <yo.natan@hotmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding new class/subclass/protocol combinations based on the GPLed
out-of-tree Huawei driver. One of these has already appeared on a
device labelled as "E320".
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a new vendor specific class/subclass/protocol combination
for CDC NCM devices based on information from a GPLed out-of-tree
driver from Huawei.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is normal for minidrivers accumulating frames to return NULL
from their tx_fixup function. We do not want to count this as a
drop, or log any debug messages. A different exit path is
therefore chosen for such drivers, skipping the debug message
and the tx_dropped increment.
The test for accumulating drivers was however completely bogus,
making the exit path selection depend on whether the user had
enabled tx_err logging or not. This would arbitrarily mess up
accounting for both accumulating and non-accumulating minidrivers,
and would result in unwanted debug messages for the accumulating
drivers.
Fix by testing for FLAG_MULTI_PACKET instead, which probably was
the intention from the beginning. This usage match the documented
behaviour of this flag:
Indicates to usbnet, that USB driver accumulates multiple IP packets.
Affects statistic (counters) and short packet handling.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add VID, PID and fixed interface for Telit LE920
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.
Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs. Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.
This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.
Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9992c2e (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant. The USB core has already done the lookup
and saved the result in the USB interface struct. Use that
instead.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reverting 328d7b8 and instead adding an exception for the
Sierra Wireless MC7710.
commit 328d7b8 (net: cdc_mbim: send ZLP after max sized NTBs)
added a workaround for an issue observed on one specific device.
Concerns were raised that this workaround adds a performance
penalty to all devices based on questionable, if not buggy,
behaviour of a single device:
"If you add ZLP for NTBs of dwNtbOutMaxSize, you are heavily affecting CPU
load, increasing interrupt load by factor of 2 in high load traffic
scenario and possibly decreasing throughput for all other devices
which behaves correctly."
"The idea of NCM was to avoid extra ZLPs. If your transfer is exactly
dwNtbOutMaxSize, it's known, you can submit such request on the receiver
side and you do not need any EOT indicatation, so the frametime can be
used for useful data."
Adding a device specific exception to prevent the workaround from
affecting well behaved devices.
The assumption here is that needing a ZLP is truly an *exception*.
We do not yet have enough data to verify this. The generic
workaround in commit 328d7b8 should be considered acceptable despite
the performance penalty if the exception list becomes a maintainance
hassle.
Cc: Alexey ORISHKO <alexey.orishko@stericsson.com>
Cc: Yauheni Kaliuta <y.kaliuta@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Infineon(now Intel) HSPA Modem platform NCM cannot support ARP.
we can define a new common structure wwan_noarp_info.
Then more similiar NO ARP devices can be handled easily
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do have some USB net devices, which cannot do ARP.
so we can introduce a new flag FLAG_NOARP, then client drivers
can easily handle this kind of devices
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bbc8d92 (net: cdc_ncm: add Huawei devices) implemented
support for devices with a single combined control and data
interface. Fix up the error path so that we do not double
release such interfaces in case of probing failures.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We normally avoid sending ZLPs by padding NTBs with a zero byte
if the NTB is shorter than dwNtbOutMaxSize, resulting in a short
USB packet instead of a ZLP. But in the case where the NTB length
is exactly dwNtbOutMaxSize and this is an exact multiplum of
wMaxPacketSize, then we must send a ZLP.
This fixes an issue seen on a Sierra Wireless MC7710 device
where the transmission would fail whenever we ended up padding
the NTBs to max size.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for the MBIM mode in some Sierra Wireless devices.
Some Sierra Wireless firmwares support CDC MBIM but have no CDC
Union funtional descriptor. This violates the MBIM specification,
but we can easily work around the bug by looking at the Interface
Association Descriptor instead. This is most likely what
Windows uses too, which explains how the firmware bug has gone
unnoticed until now.
This change will not affect any currently supported device
conforming to the NCM or MBIM specifications, as they must have
the CDC Union descriptor.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch calls device_set_wakeup_enable() inside set_wol
callback, so that turning on WOL from user mode utility
can make the 'wakeup' of pegasus device to be enabled, then
remote wakeup may be enabled before putting into sleep.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver description files gives these names to the vendor specific
functions on this modem:
Diag VID_19D2&PID_0265&MI_00
NMEA VID_19D2&PID_0265&MI_01
AT cmd VID_19D2&PID_0265&MI_02
Modem VID_19D2&PID_0265&MI_03
Net VID_19D2&PID_0265&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In two places, tmp is initialized implicitly by being passed as a
pointer during a function call. However, this is not obvious to the
compiler, which logs a warning.
Signed-off-by: Simon Que <sque@chromium.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ASIX AX88772B started to pack data even more tightly. Packets and the ASIX packet
header may now cross URB boundaries. To handle this we have to introduce
some state between individual calls to asix_rx_fixup().
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device comes up with a MAC address of all zeros. We need to read the
initial device MAC from EEPROM so it can be set properly later.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver description files gives these names to the vendor specific
functions on this modem:
Diagnostics VID_2357&PID_0201&MI_00
NMEA VID_2357&PID_0201&MI_01
Modem VID_2357&PID_0201&MI_03
Networkcard VID_2357&PID_0201&MI_04
The "Networkcard" function has been verified to support these QMI
services:
ctl (1.3)
wds (1.3)
dms (1.2)
nas (1.0)
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 24b1042c4e ("usbnet: dm9601: apply introduced usb command
APIs") removes the distiction between DM_WRITE_REG and DM_WRITE_REGS
command. The distiction is reintroduced to the driver so that the
functionality of the driver remains same.
CC: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork
Steve Glendinning
Robert de Vries
Freddy Xin
Glen Turner
Linus Torvalds
Ming Lei
Dan Williams
David S. Miller
Joe Perches
Daniele Palmas
Peter Korsgaard
Wei Shuai
Wu Fengguang
Joe Millenbach
Simon Que
Lucas Stach
Tushar Behera
Jiri Slaby