Share configuration option processing code between the dm cache
ctr and message functions.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Generate a dm event when the amount of remaining thin pool metadata
space falls below a certain level.
The threshold is taken to be a quarter of the size of the metadata
device with a minimum threshold of 4MB.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a threshold callback to dm persistent data space maps.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a threshold callback function to the persistent data space map
interface for a subsequent patch to use.
dm-thin and dm-cache are interested in knowing when they're getting
low on metadata or data blocks. This patch introduces a new method
for registering a callback against a threshold.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow the dm thin pool metadata device to be extended.
Whenever a pool is resumed, detect whether the size of the metadata
device has increased, and if so, extend the metadata to use the new
space.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support extending a dm persistent data metadata space map.
The extend itself is implemented by switching back to the boostrap
allocator and pointing to the new space. The extra bitmap indexes are
then allocated from the new space, and finally we switch back to the
proper space map ops and tweak the reference counts.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If a thin pool is created in read-only-metadata mode then only open the
metadata device read-only.
Previously it was always opened with FMODE_READ | FMODE_WRITE.
(Note that dm_get_device() still allows read-only dm devices to be used
read-write at the moment: If I create a read-only linear device for the
metadata, via dmsetup load --readonly, then I can still create a rw pool
out of it.)
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Refactor device size functions in preparation for similar metadata
device resizing functions.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Correct the documented requirement on the return code from dm cache policy
lookup functions stated in the policy module header file.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix some typos in dm-space-map-metadata.c error messages.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Tune the dm cache migration throttling.
i) Issue a tick every second, just in case there's no i/o going through.
ii) Drop the migration threshold right down to something suitable for
background work.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Enable WRITE SAME support in dm multipath. As far as multipath is
concerned it is just another write request.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Bharata B Rao <bharata.rao@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If device_not_write_same_capable() returns true then the iterate_devices
loop in dm_table_supports_write_same() should return false.
Reported-by: Bharata B Rao <bharata.rao@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.8+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch uses memalloc_noio_save to avoid a possible deadlock in
dm-bufio. (it could happen only with large block size, at most
PAGE_SIZE << MAX_ORDER (typically 8MiB).
__vmalloc doesn't fully respect gfp flags. The specified gfp flags are
used for allocation of requested pages, structures vmap_area, vmap_block
and vm_struct and the radix tree nodes.
However, the kernel pagetables are allocated always with GFP_KERNEL.
Thus the allocation of pagetables can recurse back to the I/O layer and
cause a deadlock.
This patch uses the function memalloc_noio_save to set per-process
PF_MEMALLOC_NOIO flag and the function memalloc_noio_restore to restore
it. When this flag is set, all allocations in the process are done with
implied GFP_NOIO flag, thus the deadlock can't happen.
This should be backported to stable kernels, but they don't have the
PF_MEMALLOC_NOIO flag and memalloc_noio_save/memalloc_noio_restore
functions. So, PF_MEMALLOC should be set and restored instead.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Return -ENOMEM instead of success if unable to allocate pending
exception mempool in snapshot_ctr.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a regression in the calculation of the stripe_width in the
dm stripe target which led to incorrect processing of device limits.
The stripe_width is the stripe device length divided by the number of
stripes. The group of commits in the range f14fa69 ("dm stripe: fix
size test") to eb850de ("dm stripe: support for non power of 2
chunksize") interfered with each other (a merging error) and led to the
stripe_width being set incorrectly to the stripe device length divided by
chunk_size * stripe_count.
For example, a stripe device's table with: 0 33553920 striped 3 512 ...
should result in a stripe_width of 11184640 (33553920 / 3), but due to
the bug it was getting set to 21845 (33553920 / (512 * 3)).
The impact of this bug is that device topologies that previously worked
fine with the stripe target are no longer considered valid. In
particular, there is a higher risk of seeing this issue if one of the
stripe devices has a 4K logical block size. Resulting in an error
message like this:
"device-mapper: table: 253:4: len=21845 not aligned to h/w logical block size 4096 of dm-1"
The fix is to swap the order of the divisions and to use a temporary
variable for the second one, so that width retains the intended
value.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull block driver updates from Jens Axboe:
"It might look big in volume, but when categorized, not a lot of
drivers are touched. The pull request contains:
- mtip32xx fixes from Micron.
- A slew of drbd updates, this time in a nicer series.
- bcache, a flash/ssd caching framework from Kent.
- Fixes for cciss"
* 'for-3.10/drivers' of git://git.kernel.dk/linux-block: (66 commits)
bcache: Use bd_link_disk_holder()
bcache: Allocator cleanup/fixes
cciss: bug fix to prevent cciss from loading in kdump crash kernel
cciss: add cciss_allow_hpsa module parameter
drivers/block/mg_disk.c: add CONFIG_PM_SLEEP to suspend/resume functions
mtip32xx: Workaround for unaligned writes
bcache: Make sure blocksize isn't smaller than device blocksize
bcache: Fix merge_bvec_fn usage for when it modifies the bvm
bcache: Correctly check against BIO_MAX_PAGES
bcache: Hack around stuff that clones up to bi_max_vecs
bcache: Set ra_pages based on backing device's ra_pages
bcache: Take data offset from the bdev superblock.
mtip32xx: mtip32xx: Disable TRIM support
mtip32xx: fix a smatch warning
bcache: Disable broken btree fuzz tester
bcache: Fix a format string overflow
bcache: Fix a minor memory leak on device teardown
bcache: Documentation updates
bcache: Use WARN_ONCE() instead of __WARN()
bcache: Add missing #include <linux/prefetch.h>
...
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The main fix is that bch_allocator_thread() wasn't waiting on
garbage collection to finish (if invalidate_buckets had set
ca->invalidate_needs_gc); we need that to make sure the allocator
doesn't spin and potentially block gc from finishing.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
In SSD/hard disk hybid storage, discard request should be ignored for hard
disk. We used to be doing this way, but the unplug path forgets it.
This is suitable for stable tree since v3.6.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Maintenance of a bad-block-list currently defaults to 'enabled'
and is then disabled when it cannot be supported.
This is backwards and causes problem for dm-raid which didn't know
to disable it.
So fix the defaults, and only enabled for v1.x metadata which
explicitly has bad blocks enabled.
The problem with dm-raid has been present since badblock support was
added in v3.1, so this patch is suitable for any -stable from 3.1
onwards.
Cc: stable@vger.kernel.org (3.1+)
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Hi.
Raid1 and raid10 devices leak memory every time they stop.
This is a patch for linux-3.9.0-rc7 to fix this problem.
Thanks,
Hirokazu Takahashi.
Signed-off-by: Hirokazu Takahashi <taka@valinux.co.jp>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add message/status support for changing sync action
This patch adds a message interface to dm-raid to allow the user to more
finely control the sync actions being performed by the MD driver. This
gives the user the ability to initiate "check" and "repair" (i.e. scrubbing).
Two additional fields have been appended to the status output to provide more
information about the type of sync action occurring and the results of those
actions, specifically: <sync_action> and <mismatch_cnt>. These new fields
will always be populated. This is essentially the device-mapper way of doing
what MD controls through the 'sync_action' sysfs file and shows through the
'mismatch_cnt' sysfs file.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD: Export 'md_reap_sync_thread' function
Make 'md_reap_sync_thread' available to other files, specifically dm-raid.c.
- rename reap_sync_thread to md_reap_sync_thread
- move the fn after md_check_recovery to match md.h declaration placement
- export md_reap_sync_thread
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
read-only arrays should stay that way as much as possible.
Updating the metadata - which could be triggered by a re-add
while assembling the array metadata - should be avoided.
Signed-off-by: NeilBrown <neilb@suse.de>
When assembling an array incrementally we might want to make
it device available when "enough" devices are present, but maybe
not "all" devices are present.
If the remaining devices appear before the array is actually used,
they should be added transparently.
We do this by using the "read-auto" mode where the array acts like
it is read-only until a write request arrives.
Current an add-device request switches a read-auto array to active.
This means that only one device can be added after the array is first
made read-auto. This isn't a problem for RAID5, but is not ideal for
RAID6 or RAID10.
Also we don't really want to switch the array to read-auto at all
when re-adding a device as this doesn't really imply any change.
So:
- remove the "md_update_sb()" call from add_new_disk(). This isn't
really needed as just adding a disk doesn't require a metadata
update. Instead, just set MD_CHANGE_DEVS. This will effect a
metadata update soon enough, once the array is not read-only.
- Allow the ADD_NEW_DISK ioctl to succeed without activating a
read-auto array, providing the MD_DISK_SYNC flag is set.
In this case, the device will be rejected if it cannot be added
with the correct device number, or has an incorrect event count.
- Teach remove_and_add_spares() to be careful about adding spares
when the array is read-only (or read-mostly) - only add devices
that are thought to be in-sync, and only do it if the array is
in-sync itself.
- In md_check_recovery, use remove_and_add_spares in the read-only
case, rather than open coding just the 'remove' part of it.
Reported-by: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is assembled incrementally with mdadm -I -R
and the array switches to "active" mode, md starts a recovery.
If the array was clean, the "fullsync" flag will be 0. Skip
the full recovery in this case, as RAID1 does (the code was
actually copied from the sync_request() method of RAID1).
Signed-off-by: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
If we write to a known-bad-block it will be flags as having
a ReadError by analyse_stripe, but the write will proceed anyway
(as it should). Then the read-error handling will kick in an
write again, then re-read.
We don't need that 'write-again', so set R5_ReWrite so it looks like
it has already been done. Then we will just get the re-read, which we
want.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
As the function call is the most expensive of these tests it should be
done later in the chain so that it can be avoided in some cases.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The value returned by test_and_set_bit_le() drivers/md/bitmap.c is not used.
So just use set_bit_le(). The same goes for test_and_clear_bit_le().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If a fail device or a spare is removed from an array, there is
not need to make the array 'active'. If/when the array does become
active for some other reason the metadata will be update to reflect
the removal.
If that never happens and the array is stopped while still read-auto,
then there is no loss in forgetting the that the device had 'failed'.
A read-only array will leave failed devices attached to
the array personality, so we need to explicitly call
remove_and_add_spares() to free it (clearing Blocked just
like we do in store_slot()).
Signed-off-by: NeilBrown <neilb@suse.de>
slot_store and remove_and_add_spares both call ->hot_remove_disk(),
but with slightly different tests and consequences, which is
at least untidy and might be buggy.
So modify remove_and_add_spaces() so that it can be asked
to remove a specific device, and call it from slot_store().
We also clear the Blocked flag to ensure that doesn't prevent
removal. The purpose of Blocked is to prevent automatic removal
by the kernel before an error is acknowledged.
If the array is read/write then user-space would have not reason
to remove a device unless it was known to be 'spare' or 'faulty' in
which it would have already cleared the Blocked flag.
If the array is read-only, the flag might still be blocked, but
there is no harm in clearing the flag for read-only arrays.
Signed-off-by: NeilBrown <neilb@suse.de>
Normally we don't even try to update the metadata if
the array is read-only. However future patches
will increase the number of things that can happen on a read-only
array, so it is safest to explicitly disable this.
Every time that mddev->ro is set to 0, either
- md_update_sb will be called again (at least if MD_CHANGE_DEVS
is set) or
- the mddev->thread is scheduled, which will also run
md_update_sb if needed.
So this is safe: if the array ever become read-write the
metadata will be updated.
Signed-off-by: NeilBrown <neilb@suse.de>
Stacked md devices reuse the bvm for the subordinate device, causing
problems...
Reported-by: Michael Balser <michael.balser@profitbricks.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
bch_bio_max_sectors() was checking against BIO_MAX_PAGES as if the limit
was for the total bytes in the bio, not the number of segments.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Add a new superblock version, and consolidate related defines.
Signed-off-by: Gabriel de Perthuis <g2p.code+bcache@gmail.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
This reverts commit 3a366e614d.
Wanlong Gao reports that it causes a kernel panic on his machine several
minutes after boot. Reverting it removes the panic.
Jens says:
"It's not quite clear why that is yet, so I think we should just revert
the commit for 3.9 final (which I'm assuming is pretty close).
The wifi is crap at the LSF hotel, so sending this email instead of
queueing up a revert and pull request."
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Requested-by: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Thornber