Commit Graph

349 Commits

Author SHA1 Message Date
pascal@pabr.org 60ec6571c5 MIPS: Support 36-bit iomem on 32-bit Au1x00
I believe these changes are needed on Alchemy SoCs in order to
use iomem above 4G with the usual platform_device machinery:

- Set CONFIG_ARCH_PHYS_ADDR_T_64BIT to make resource_size_t 64-bit.
- Increase IOMEM_RESOURCE_END so that platforms can register resources.

To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:53:17 +01:00
Florian Fainelli 5f3c909881 MIPS: AR7: Implement gpiolib
This patch implements gpiolib for the AR7 SoC.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/816/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:53:16 +01:00
Wu Zhangjin c7e8c668b0 MIPS: Loongson: Remove the serial port output of compressed kernel support
The compressed kernel support on loongson family machines is stable now,
so, remove the debug information via using SYS_SUPPORTS_ZBOOT instead of
SYS_SUPPORTS_ZBOOT_UART16550. This may reduce the image size and speedup
the booting.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: zhangfx@lemote.com
Patchwork: http://patchwork.linux-mips.org/patch/824/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:53:10 +01:00
David Daney 6b07d38aaa MIPS: Octeon: Use optimized memory barrier primitives.
In order to achieve correct synchronization semantics, the Octeon port
had defined CONFIG_WEAK_REORDERING_BEYOND_LLSC.  This resulted in code
that looks like:

   sync
   ll ...
   .
   .
   .
   sc ...
   .
   .
   sync

The second SYNC was redundant, but harmless.

Octeon has a SYNCW instruction that acts as a write-memory-barrier
(due to an erratum in some parts two SYNCW are used).  It is much
faster than SYNC because it imposes ordering on the writes, but
doesn't otherwise stall the execution pipeline.  On Octeon, SYNC
stalls execution until all preceeding writes are committed to the
coherent memory system.

Using:

    syncw;syncw
    ll
    .
    .
    .
    sc
    .
    .

Has identical semantics to the first sequence, but is much faster.
The SYNCW orders the writes, and the SC will not complete successfully
until the write is committed to the coherent memory system.  So at the
end all preceeding writes have been committed.  Since Octeon does not
do speculative reads, this functions as a full barrier.

The patch removes CONFIG_WEAK_REORDERING_BEYOND_LLSC, and substitutes
SYNCW for SYNC in write-memory-barriers.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/850/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:53:06 +01:00
Wu Zhangjin fe1d45e086 MIPS: Add support of LZO-compressed kernels
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Patchwork: http://patchwork.linux-mips.org/patch/857/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-01-28 00:03:30 +01:00
Martin Michlmayr a4609780c9 MIPS: No longer hardwire CONFIG_EMBEDDED to y
There's no reason for MIPS to select EMBEDDED.  In fact, EMBEDDED makes
MIPS more awkward to deal with because it makes it different to the
majority of architectures for no good reason.

[Ralf: Historically disabling EMBEDDED had hid essential options for many
 MIPS platforms such as serial console and forced crap like VGA support
 or power managment enabled for platforms where those don't make any sense.

 The name of the option is also _very_ missleading so many users don't
 select it even where is was required for a functioning kernel.]

Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/663/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:36 +00:00
Ralf Baechle de4148f3ef MIPS: eXcite: Remove platform.
The platform has never been fully merged 

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
2009-12-17 01:57:35 +00:00
Ralf Baechle 4dd92e15b3 MIPS: Move EARLY_PRINTK to Kconfig.debug
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:30 +00:00
Wu Zhangjin 29c5d3462f MIPS: Tracing: Add function graph tracer support for MIPS
The implementation of function graph tracer for MIPS is a little
different from X86.

in MIPS, gcc(with -pg) only transfer the caller's return address(at) and
the _mcount's return address(ra) to us.

For the kernel part without -mlong-calls:

move at, ra
jal _mcount

For the module part with -mlong-calls:

lui v1, hi16bit_of_mcount
addiu v1, v1, low16bit_of_mcount
move at, ra
jal _mcount

Without -mlong-calls,

if the function is a leaf, it will not save the return address(ra):

ffffffff80101298 <au1k_wait>:
ffffffff80101298:       67bdfff0        daddiu  sp,sp,-16
ffffffff8010129c:       ffbe0008        sd      s8,8(sp)
ffffffff801012a0:       03a0f02d        move    s8,sp
ffffffff801012a4:       03e0082d        move    at,ra
ffffffff801012a8:       0c042930        jal     ffffffff8010a4c0 <_mcount>
ffffffff801012ac:       00020021        nop

so, we can hijack it directly in _mcount, but if the function is non-leaf, the
return address is saved in the stack.

ffffffff80133030 <copy_process>:
ffffffff80133030:       67bdff50        daddiu  sp,sp,-176
ffffffff80133034:       ffbe00a0        sd      s8,160(sp)
ffffffff80133038:       03a0f02d        move    s8,sp
ffffffff8013303c:       ffbf00a8        sd      ra,168(sp)
ffffffff80133040:       ffb70098        sd      s7,152(sp)
ffffffff80133044:       ffb60090        sd      s6,144(sp)
ffffffff80133048:       ffb50088        sd      s5,136(sp)
ffffffff8013304c:       ffb40080        sd      s4,128(sp)
ffffffff80133050:       ffb30078        sd      s3,120(sp)
ffffffff80133054:       ffb20070        sd      s2,112(sp)
ffffffff80133058:       ffb10068        sd      s1,104(sp)
ffffffff8013305c:       ffb00060        sd      s0,96(sp)
ffffffff80133060:       03e0082d        move    at,ra
ffffffff80133064:       0c042930        jal     ffffffff8010a4c0 <_mcount>
ffffffff80133068:       00020021        nop

but we can not get the exact stack address(which saved ra) directly in
_mcount, we need to search the content of at register in the stack space
or search the "s{d,w} ra, offset(sp)" instruction in the text. 'Cause we
can not prove there is only a match in the stack space, so, we search
the text instead.

as we can see, if the first instruction above "move at, ra" is not a
store instruction, there should be a leaf function, so we hijack the at
register directly via putting &return_to_handler into it, otherwise, we
search the "s{d,w} ra, offset(sp)" instruction to get the stack offset,
and then the stack address. we use the above copy_process() as an
example, we at last find "ffbf00a8", 0xa8 is the stack offset, we plus
it with s8(fp), that is the stack address, we hijack the content via
writing the &return_to_handler in.

If with -mlong-calls, since there are two more instructions above "move
at, ra", so, we can move the pointer to the position above "lui v1,
hi16bit_of_mcount".

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/677/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:25 +00:00
Wu Zhangjin 538f19526e MIPS: Tracing: Add dynamic function tracer support
With dynamic function tracer, by default, _mcount is defined as an
"empty" function, it returns directly without any more action . When
enabling it in user-space, it will jump to a real tracing
function(ftrace_caller), and do the real job for us.

Differ from the static function tracer, dynamic function tracer provides
two functions ftrace_make_call()/ftrace_make_nop() to enable/disable the
tracing of some indicated kernel functions(set_ftrace_filter).

In the -v4 version, the implementation of this support is basically the same as
X86 version does: _mcount is implemented as an empty function and ftrace_caller
is implemented as a real tracing function respectively.

But in this version, to support module tracing with the help of
-mlong-calls in arch/mips/Makefile:

MODFLAGS += -mlong-calls.

The stuff becomes a little more complex. We need to cope with two
different type of calling to _mcount.

For the kernel part, the calling to _mcount(result of "objdump -hdr
vmlinux"). is like this:

	108:   03e0082d        move    at,ra
	10c:   0c000000        jal     0 <fpcsr_pending>
                        10c: R_MIPS_26  _mcount
                        10c: R_MIPS_NONE        *ABS*
                        10c: R_MIPS_NONE        *ABS*
	110:   00020021        nop

For the module with -mlong-calls, it looks like this:

	c:	3c030000 	lui	v1,0x0
			c: R_MIPS_HI16	_mcount
			c: R_MIPS_NONE	*ABS*
			c: R_MIPS_NONE	*ABS*
	10:	64630000 	daddiu	v1,v1,0
			10: R_MIPS_LO16	_mcount
			10: R_MIPS_NONE	*ABS*
			10: R_MIPS_NONE	*ABS*
	14:	03e0082d 	move	at,ra
	18:	0060f809 	jalr	v1

In the kernel version, there is only one "_mcount" string for every
kernel function, so, we just need to match this one in mcount_regex of
scripts/recordmcount.pl, but in the module version, we need to choose
one of the two to match. Herein, I choose the first one with
"R_MIPS_HI16 _mcount".

and In the kernel verion, without module tracing support, we just need
to replace "jal _mcount" by "jal ftrace_caller" to do real tracing, and
filter the tracing of some kernel functions via replacing it by a nop
instruction.

but as we have described before, the instruction "jal ftrace_caller" only left
32bit length for the address of ftrace_caller, it will fail when calling from
the module space. so, herein, we must replace something else.

the basic idea is loading the address of ftrace_caller to v1 via changing these
two instructions:

	lui	v1,0x0
	addiu	v1,v1,0

If we want to enable the tracing, we need to replace the above instructions to:

	lui	v1, HI_16BIT_ftrace_caller
	addiu	v1, v1, LOW_16BIT_ftrace_caller

If we want to stop the tracing of the indicated kernel functions, we
just need to replace the "jalr v1" to a nop instruction. but we need to
replace two instructions and encode the above two instructions
oursevles.

Is there a simpler solution? Yes! Here it is, in this version, we put _mcount
and ftrace_caller together, which means the address of _mcount and
ftrace_caller is the same:

_mcount:
ftrace_caller:
	j	ftrace_stub
	 nop

	...(do real tracing here)...

ftrace_stub:
	jr	ra
	 move	ra, at

By default, the kernel functions call _mcount, and then jump to ftrace_stub and
return. and when we want to do real tracing, we just need to remove that "j
ftrace_stub", and it will run through the two "nop" instructions and then do
the real tracing job.

what about filtering job? we just need to do this:

	 lui v1, hi_16bit_of_mcount        <--> b 1f (0x10000004)
	 addiu v1, v1, low_16bit_of_mcount
	 move at, ra
	 jalr v1
	 nop
	 				     1f: (rec->ip + 12)

In linux-mips64, there will be some local symbols, whose name are
prefixed by $L, which need to be filtered. thanks goes to Steven for
writing the mips64-specific function_regex.

In a conclusion, with RISC, things becomes easier with such a "stupid"
trick, RISC is something like K.I.S.S, and also, there are lots of
"simple" tricks in the whole ftrace support, thanks goes to Steven and
the other folks for providing such a wonderful tracing framework!

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/675/
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:23 +00:00
Wu Zhangjin 69a7d1b3ec MIPS: Tracing: Enable HAVE_FUNCTION_TRACE_MCOUNT_TEST for MIPS
There is an exisiting common ftrace_test_stop_func() in
kernel/trace/ftrace.c, which is used to check the global variable
ftrace_trace_stop to determine whether stop the function tracing.

This patch implepment the MIPS specific one to speedup the procedure.

Thanks goes to Zhang Le for Cleaning it up.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/673/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:22 +00:00
Wu Zhangjin d2bb076299 MIPS: Tracing: Add static function tracer support for MIPS
If -pg of gcc is enabled with CONFIG_FUNCTION_TRACER=y. a calling to
_mcount will be inserted into each kernel function. so, there is a
possibility to trace the kernel functions in _mcount.

This patch add the MIPS specific _mcount support for static function
tracing. by default, ftrace_trace_function is initialized as
ftrace_stub(an empty function), so, the default _mcount will introduce
very little overhead. after enabling ftrace in user-space, it will jump
to a real tracing function and do static function tracing for us.

and -ffunction-sections is incompatible with -pg, so, disable it when
ftracer is enabled.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:21 +00:00
Wu Zhangjin 9726b43a4d MIPS: Add basic CPUFreq options.
This patch adds basic options for MIPS CPUFreq support.

Since the cp0 timer's frequency is based on the processor clockrate it can
not be used with CPUFReq; an additional external timer is required.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cpufreq@vger.kernel.org,
Cc: Dave Jones <davej@redhat.com>,
Cc: Dominik Brodowski <linux@dominikbrodowski.net>,
Cc: yanh@lemote.com
Cc: huhb@lemote.com,
Patchwork: http://patchwork.linux-mips.org/patch/659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:20 +00:00
David VomLehn a3a0f8c8ed MIPS: PowerTV: Base files for Cisco PowerTV platform
Add the Cisco Powertv cable settop box to the MIPS tree. This platform is
based on a MIPS 24Kc processor with various devices integrated on the same
ASIC. There are multiple models of this box, with differing configuration
but the same kernel runs across the product line.

Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:17 +00:00
Wu Zhangjin 22f1fdfd62 MIPS: Add support for uncached accelerated mappings.
Loongson2f support video acceleration.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/624/
Patchwork: http://patchwork.linux-mips.org/patch/625/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:15 +00:00
Wu Zhangjin 55045ff555 MIPS: Loongson 2F: Cleanup the #if clauses
This patch adds two new kernel options: CPU_SUPPORTS_CPUFREQ and
CPU_SUPPORTS_ADDRWINCFG to describe the new features of Loongons 2F and
replaces the several ugly #if clauses by them.

These two options will be utilized by the future loongson revisions and
related drivers such as the coming Loongson 2F CPUFreq driver.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:15 +00:00
Wu Zhangjin 21a41faa4d MIPS: Lemote 2f: Enable legacy RTC driver
Currently rtclib is not available on Loongson family machines but the
legacy RTC driver works well on them.  Deselect RTC_LIB to allow the legacy
RTC driver to be selected.

The rtclib patch series

   http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=a91e34bf2595157830d599cb66becd52247b1819.1257383766.git.wuzhangjin%40gmail.com

or, in patchworks:

   http://patchwork.linux-mips.org/patch/570/
   http://patchwork.linux-mips.org/patch/571/
   http://patchwork.linux-mips.org/patch/572/

is eventually going to switch Lemote platforms to rtclib.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com 
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:11 +00:00
Wu Zhangjin 6f7a251a25 MIPS: Loongson: Add basic Loongson 2F support
Loongson 2F has built-in DDR2 and PCI-X controller. The PCI-X controller
has a programming interface similiar to the the FPGA northbridge used on
Loongson 2E.

The main differences between Loongson 2E and Loongson 2F include:

1. Loongson 2F has an extra address window configuration module, which
   is used to map CPU address space to DDR or PCI address space, or map
   the PCI-DMA address space to DDR or LIO address space.

2. Loongson 2F supports 8 levels of software configurable CPu frequency
   which can be configured in the LOONGSON_CHIPCFG0 register.  The coming
   cpufreq and standby support are based on this feature.

Loongson.h abstracts the modules and corresponding methods are abstracted.

Add other Loongson-2F-specific source code including gcc 4.4 support, PCI
memory space, PCI IO space, DMA address.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:10 +00:00
Ralf Baechle 32028f1f7b MIPS: Remove addinitrd and CONFIG_PROBE_INITRD_HEADER
Addinitrd has been superseded by initramfs ages ago.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:07 +00:00
David Daney 82622284dd MIPS: Put PGD in C0_CONTEXT for 64-bit R2 processors.
Processors that support the mips64r2 ISA can in four instructions
convert a shifted PGD pointer stored in the upper bits of c0_context
into a usable pointer.  By doing this we save a memory load and
associated potential cache miss in the TLB exception handlers.

Since the upper bits of c0_context were holding the CPU number, we
move this to the upper bits of c0_xcontext which doesn't have enough
bits to hold the PGD pointer, but has plenty for the CPU number.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:57:01 +00:00
Wu Zhangjin 1b93b3c3e9 MIPS: Add support for GZIP / BZIP2 / LZMA compressed kernel images
This patch helps to generate smaller kernel images for linux-MIPS,

Here is the effect when using lzma:

$ ls -sh vmlinux
7.1M vmlinux
$ ls -sh vmlinuz
1.5M vmlinuz

Have tested the 32bit kernel on Qemu/Malta and 64bit kernel on FuLoong
Mini PC. both of them work well. and also, tested by Alexander Clouter
on an AR7 based Linksys WAG54Gv2, and by Manuel Lauss on an Alchemy
board.

This -v2 version incorporate the feedback from Ralf, and add the
following changes:

1. add .ecoff, .bin, .erec format support
2. only enable it and the debug source code for the machines we tested
3. a dozen of fixups and cleanups

and if you want to enable it for your board, please try to select
SYS_SUPPORTS_ZBOOT for it, and if the board have an 16550 compatible
uart, you can select SYS_SUPPORTS_ZBOOT_UART16550 directly. and then
sending the relative patches to Ralf.

Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
Tested-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-17 01:56:56 +00:00
Wu Zhangjin f133f22dd6 MIPS: Loongson: Switch from flatmem to sparsemem
With flatmem hibernation for Loongson will fail, and there are also some
other problems such as broken files when using NFS or CIFS / Samba.

The config help of sparsemem says:

"This option provides some potential performance benefits, along with
decreased code complexity."

So to avoid the potential problems of FLATMEM, we disable FLATMEM directly
and use SPARSEMEM instead.

Related email thread:

http://groups.google.com/group/loongson-dev/browse_thread/thread/b6b65890ec2b0f24/feb43e5aa7f55d9b?show_docid=feb43e5aa7f55d9b

Reported-by: Tatu Kilappa <tatu.kilappa@gmail.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/737/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-01 16:21:26 +00:00
Wu Zhangjin 315fe625f8 MIPS: Loongson: Disallow 4kB pages
Currently, with PAGE_SIZE_4KB, the kernel for loongson will hang on:

Kernel panic - not syncing: Attempted to kill init!

The possible reason is the cache aliases problem:

Loongson 2F has 64kb, 4 way L1 Cache, the way size is 16kb, which is bigger
then 4kb. so, If using 4kb page size, there is cache aliases problem.
To avoid this kind of problem, extra cache flushing.  The 2nd possible
solution is 16kb page size which avoids cache aliases without the need for
extra cache flushes.  So we disable 4kB pages until the aliasing issue is
solved.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/736/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-01 16:21:26 +00:00
Martin Michlmayr 2b5e63f6b8 MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.
Some Debian users have reported that the kernel hangs early during boot on
some IP22 systems.  Thomas Bogendoerfer found that this is due to a "bad
interaction between CONFIG_EARLY_PRINTK and overwritten prom memory during
early boot".  Since there's no fix yet, disable CONFIG_EARLY_PRINTK for now.

Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-12-01 16:21:25 +00:00
Yoichi Yuasa f8ac04255d MIPS: Add DMA declare coherent memory support
The ohci-sm501 driver requires dma_declare_coherent_memory().  It is used
by the driver's local memory allocation with dma_alloc_coherent().

Tested on TANBAC TB0287(VR4131 + SM501).

[Ralf: Fixed reject in dma-default.c and removed the entire #if 0'ed block
 in dma-mapping.h instead of just the #if 0.]

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-11-13 18:10:37 +01:00
Ralf Baechle 0db2b74e91 MIPS: Set S-cache linesize to 64-bytes for MTI's S-cache
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-11-02 12:00:06 +01:00
Ralf Baechle c708875551 MIPS: Kconfig: Fix duplicate default value for MIPS_L1_CACHE_SHIFT.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-11-02 12:00:04 +01:00
Maxime Bizon e7300d04bd MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-09-17 20:07:52 +02:00
Ralf Baechle f7ade3c168 MIPS: Get rid of CONFIG_CPU_HAS_LLSC
CONFIG_CPU_HAS_LLSC duplicated the function of cpu_has_llsc for no good
reason and and the results if the one was enabled and the other disabled
was very unobvious.  Remove it now that there are no more remaining users.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-09-17 20:07:50 +02:00
Wu Zhangjin 3702bba5eb MIPS: Loongson: Add GCC 4.4 support for Loongson2E
Because only gcc >=4.4 have loongson-specific support, we need to choose
the suitable -march argument for gcc <= 4.3 and gcc >= 4.4, and here, we
use -march=loongson2e for loongson2e.

Thanks goes to Arnaud Patard <apatard@mandriva.com> for suggestion of
using cc-options(Documentation/kbuild/makefiles.txt). and thanks Zhang
Le for introducing the new CPU_LOONGSON2E kernel option.

NOTE: -mtune option is not need if -march and -mtune use the same value.

Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-09-17 20:07:47 +02:00
Wu Zhangjin 85749d24bc MIPS: Loongson: Split common loongson source code out
To share common loongson source code between all of the loongson-based
machines. there is a need to split it out of the fuloong-2e/ directory.
at the same time, other according tuning is needed. the machine-specific
parts are defined as macros in relative header file, pci.h, mem.h,
machine.h.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-09-17 20:07:47 +02:00
Wu Zhangjin 8e4971175a MIPS: Loongson: Change naming methods
To make source code of loongson sharable to the machines(such as gdium)
made by the other companies, we rename arch/mips/lemote to
arch/mips/loongson, asm/mach-lemote to asm/mach-loongson, and rename lm2e
to the name of the machine: fuloong-2e. accordingly, FULONG are renamed to
FULOONG2E to make it distinguishable to the future FULOONG2F.  and also,
some other relative tuning is needed.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-09-17 20:07:47 +02:00
Wu Zhangjin 92d1b63dba MIPS: Loongson: RTC: Enable legacy RTC driver on fulong
RTC_LIB is selected by MIPS by default, and therefore, the legacy RTC
driver is disabled. but fortunately, RTC_LIB not works on fulong, so,
enabling the legcy RTC driver is needed, otherwise, the tools like
hwclock will not work.

Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-09-17 20:07:47 +02:00
Ralf Baechle 3f5b3e17f7 MIPS: Allow suspend and hibernation again on uniprocessor kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
2009-07-03 15:45:28 +01:00
Tim Anderson eb9b5141a9 MIPS: CMP: Update sync-r4k for current kernel
This revises the sync-4k so it will boot and operate since the removal of
expirelo from the timer code.

Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-07-03 15:45:27 +01:00
Tim Anderson 0365070f05 MIPS: CMP: activate CMP support
Most of the CMP support was added before, this mostly correct compile
problems but adds a platform specific translation for the interrupt number
based on cpu number.

Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-07-03 15:45:26 +01:00
Yoichi Yuasa 27fdd325da MIPS: Update VR41xx GPIO driver to use gpiolib
Signed-off-by: Yoichi Yuasa <yyuasa@linux.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-07-03 15:45:25 +01:00
Florian Fainelli 7ca5dc145b MIPS: Add support for Texas Instruments AR7 System-on-a-Chip
This patch adds support for the Texas Instruments AR7 System-on-a-Chip.
It supports the TNETD7100, 7200 and 7300 versions of the SoC.

Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eugene Konev <ejka@openwrt.org>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-07-03 15:45:23 +01:00
Ralf Baechle 773cb77d0e MIPS: Cavium: Add CPU hotplugging code.
Thanks to Cavium Inc. for the code contribution and help.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-24 18:34:40 +01:00
Ralf Baechle 9801b321ec MIPS: SMP: Allow suspend and hibernation if CPU hotplug is available
The SMP implementation of suspend and hibernate depends on CPU hotplugging.
In the past we didn't have CPU hotplug so suspend and hibernation were not
possible on SMP systems.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-24 18:34:40 +01:00
Ralf Baechle 1b2bc75c1b MIPS: Add arch generic CPU hotplug
Each platform has to add support for CPU hotplugging itself by providing
suitable definitions for the cpu_disable and cpu_die of the smp_ops
methods and setting SYS_SUPPORTS_HOTPLUG_CPU.  A platform should only set
SYS_SUPPORTS_HOTPLUG_CPU once all it's smp_ops definitions have the
necessary changes.  This patch contains the changes to the dummy smp_ops
definition for uni-processor systems.

Parts of the code contributed by Cavium Inc.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-24 18:34:40 +01:00
Wu Zhangjin 363c55cae5 MIPS: Add hibernation support
[Ralf: SMP support requires CPU hotplugging which MIPS currently doesn't
support.  As implemented in this patch cache and tlb flushing will also be
invoked with interrupts disabled so smp_call_function() will blow up in
charming ways.  So limit to !SMP.]

Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Yan Hua <yanh@lemote.com>
Reviewed-by: Arnaud Patard <apatard@mandriva.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Hu Hongbing <huhb@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-17 11:06:31 +01:00
David Daney 9cffd154cf MIPS: Kconfig Add SYS_SUPPORTS_HUGETLBFS and enable it for some systems.
Add new kconfig variables SYS_SUPPORTS_HUGETLBFS and
CPU_SUPPORTS_HUGEPAGES.  They are enabled for systems that are known
to support huge pages.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-17 11:06:31 +01:00
David Daney e8635b484f MIPS: Add Cavium OCTEON PCI support.
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-17 11:06:25 +01:00
Yoichi Yuasa e25bfc9243 MIPS: Cobalt: PCI bus is always required to obtain the board ID
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-08 16:57:50 +01:00
Yoichi Yuasa c9d89d97f0 MIPS: Kconfig: Remove "Support for" from Cavium system type
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-08 16:57:50 +01:00
Ralf Baechle 237e5a3443 MIPS: Kconfig: Delete duplicate definition of RWSEM_GENERIC_SPINLOCK.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-05-14 13:50:27 +01:00
Ralf Baechle c52399bece MIPS: Cavium: Add support for 8k and 32k page sizes.
Beyond the requirements of the architecture standard Cavium also supports
8k and 32k pages.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David Daney <ddaney@caviumnetworks.com>
2009-05-14 13:50:27 +01:00
Linus Torvalds 811158b147 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
  trivial: Update my email address
  trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
  trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
  trivial: Fix misspelling of "Celsius".
  trivial: remove unused variable 'path' in alloc_file()
  trivial: fix a pdlfush -> pdflush typo in comment
  trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
  trivial: wusb: Storage class should be before const qualifier
  trivial: drivers/char/bsr.c: Storage class should be before const qualifier
  trivial: h8300: Storage class should be before const qualifier
  trivial: fix where cgroup documentation is not correctly referred to
  trivial: Give the right path in Documentation example
  trivial: MTD: remove EOL from MODULE_DESCRIPTION
  trivial: Fix typo in bio_split()'s documentation
  trivial: PWM: fix of #endif comment
  trivial: fix typos/grammar errors in Kconfig texts
  trivial: Fix misspelling of firmware
  trivial: cgroups: documentation typo and spelling corrections
  trivial: Update contact info for Jochen Hein
  trivial: fix typo "resgister" -> "register"
  ...
2009-04-03 15:24:35 -07:00
Matt LaPlante 692105b8ac trivial: fix typos/grammar errors in Kconfig texts
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-03-30 15:22:01 +02:00