This patch enables the Migo-R specific touch screen
driver in the Migo-R defconfig.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a new entry to the modedb for 864x480 TAAL panels, the default
configuration for many OMAP boards. This enables omapfb to make use of
the standard mode parsing.
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These patch fix a longstanding bug in the i810 frame buffer driver.
The handling of the i2c bus is wrong: A 1 bit should not written to the
i2c, these will be done by switch the i2c to input. Driving an 1 bit
active is against the i2c spec.
An active driven of a 1 bit will result in very strange error, depending
which side is the more powerful one. In my case it depends on the
temperature of the Display-Controller-EEprom: With an cold eprom a got
the correct EDID datas, with a warm one some of the 1 bits was 0 :-(
The same bug is also in the intelfb driver in the file
drivers/video/intelfb/intelfb_i2c.c. The functions intelfb_gpio_setscl()
and intelfb_gpio_setsda() do drive the 1 bit active to the i2c bus. But
since i have no card which is used by the intelfb driver i cannot fix
it.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Resurrected some old hardware and fixed up the hgafb driver to work
again. Only tested with fbcon, since most fbdev-based software appears
to only support 12bpp and up. It does not appear that this driver has
worked for at least the entire 2.6.x series, perhaps since 2002.
Hercules graphics hardware uses packed pixels horizontally, but rows are
not linear. In other words, the pixels are not packed vertically. This
means that custom imageblit, fillrect and copyarea need to be written
specific to the hardware.
* Removed the experimental acceleration option, since it is required
for the hardware to work.
* Fixed imageblit to work with fb_image's wider than 8 pixels.
* Updated configuration text (HGA hardware is from 1984)
Signed-off-by: Brent Cook <busterb@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code had an error handling goto to the wrong place, a misplaced
release_mem_region, and a duplicated release_mem_region.
The semantic match that finds the double release_mem_region is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression e1,e2,e3;
position p1,p2,p3;
@@
release_mem_region@p1(e1, e2)@p3;
... when != request_mem_region(e1,e2,e3)
release_mem_region(e1, e2)@p2;
@@
expression e <= r.e1,e3;
expression r.e1,e2;
position r.p1,r.p2,r.p3,p!=r.p1;
@@
*release_mem_region(e1, e2)@p3;
... when != e = e3
*release_mem_region@p(e1, e2)@p2;// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
MX27 and MX25 have 10 bits in the YMAX field of LCDC Size Register.
Fix the maximum value for yres.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch extends the LCDC driver with 24 bpp
and 32 bpp support.
These modes have been kept disabled earlier due
to dependencies between the potential two LCDC
channels that are exported as two separate
framebuffer devices. The dependency boils down
to a byte swap register that is shared between
multiple channels.
With this patch applied all single channel LCDC
hardware can chose freely from 16, 24 and 32 bpp.
Dual channel LCDC must stick to the same setup
for both channels.
Without this patch only 16 bpp is fully supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fsib_clk will be used when fdiv_clk failed on fsi_hdmi_set_rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
unix_release() can asynchornously set socket->sk to NULL, and
it does so without holding the unix_state_lock() on "other"
during stream connects.
However, the reverse mapping, sk->sk_socket, is only transitioned
to NULL under the unix_state_lock().
Therefore make the security hooks follow the reverse mapping instead
of the forward mapping.
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 57dbb2d83d (sched: add head drop fifo queue)
introduced pfifo_head_drop, and broke the invariant that
sch->bstats.bytes and sch->bstats.packets are COUNTER (increasing
counters only)
This can break estimators because est_timer() handles unsigned deltas
only. A decreasing counter can then give a huge unsigned delta.
My mid term suggestion would be to change things so that
sch->bstats.bytes and sch->bstats.packets are incremented in dequeue()
only, not at enqueue() time. We also could add drop_bytes/drop_packets
and provide estimations of drop rates.
It would be more sensible anyway for very low speeds, and big bursts.
Right now, if we drop packets, they still are accounted in byte/packets
abolute counters and rate estimators.
Before this mid term change, this patch makes pfifo_head_drop behavior
similar to other qdiscs in case of drops :
Dont decrement sch->bstats.bytes and sch->bstats.packets
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow this snuck into my earlier patch, and
only now did I see a compiler warning:
net/mac80211/led.c:218:13: warning: function '__ieee80211_create_tpt_led_trigger' with external linkage has definition
Remove the stray extern.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver has remain-on-channel offload,
implement off-channel transmission using that
primitive.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to support remain-on-channel
offload if they implement smarter timing or need
to use a device implementation like iwlwifi.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provides documentation for the following:
- the new power trace API,
- the old (legacy) power trace API,
- the DEPRECATED Kconfig option usage.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: trenn@suse.de
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: linux-pm@lists.linux-foundation.org
LKML-Reference: <1294253342-29056-3-git-send-email-j-pihet@ti.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Uses the machine_suspend trace point, called from the
generic kernel suspend_devices_and_enter function.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Arjan van de Ven <arjan@linux.intel.com>
CC: Thomas Renninger <trenn@suse.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-pm@lists.linux-foundation.org
LKML-Reference: <1294253342-29056-2-git-send-email-j-pihet@ti.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ST Micro variants has some specific dma burst threshold compensation,
which allows them to make better use of a DMA controller. Add support
to set this up.
Based on a patch from Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DMA engine support for transmit to the PL011 driver. Based on a
patch from Linus Walliej, with the following changes:
- remove RX DMA support. As PL011 doesn't give us receive timeout
interrupts, we only get notified of received data when the RX DMA
has completed. This rather sucks for interactive use of the TTY.
- remove abuse of completions. Completions are supposed to be for
events, not to tell what condition buffers are in. Replace it with
a simple 'queued' bool.
- fix locking - it is only safe to access the circular buffer with the
port lock held.
- only map the DMA buffer when required - if we're ever behind an IOMMU
this helps keep IOMMU usage down, and also ensures that we're legal
when we change the scatterlist entry length.
- fix XON/XOFF sending - we must send XON/XOFF characters out as soon
as possible - waiting for up to 4095 characters in the DMA buffer
to be sent first is not acceptable.
- fix XON/XOFF receive handling - we need to stop DMA when instructed
to by the TTY layer, and restart it again when instructed to. There
is a subtle problem here: we must not completely empty the circular
buffer with DMA, otherwise we will not be notified of XON.
- change the 'enable_dma' flag into a 'using DMA' flag, and track
whether we can use TX DMA by whether the channel pointer is non-NULL.
This gives us more control over whether we use DMA in the driver.
- we don't need to have the TX DMA buffer continually allocated for
each port - instead, allocate it when the port starts up, and free
it when it's shut down. Update the 'using DMA' flag if we get
the buffer, and adjust the TTY FIFO size appropriately.
- if we're going to use PIO to send characters, use the existing IRQ
based functionality rather than reimplementing it. This also ensures
we call uart_write_wakeup() at the appropriate time, otherwise we'll
stall.
- use DMA engine helper functions for type safety.
- fix init when built as a module - we can't have to initcall functions,
so we must settle on one. This means we can eliminate the deferred
DMA initialization.
- there is no need to terminate transfers on a failed prep_slave_sg()
call - nothing has been setup, so nothing needs to be terminated.
This avoids a potential deadlock in the DMA engine code
(tasklet->callback->failed prepare->terminate->tasklet_disable
which then ends up waiting for the tasklet to finish running.)
- Dan says that the submission callback should not return an error:
| dma_submit_error() is something I should have removed after commit
| a0587bcf "ioat1: move descriptor allocation from submit to prep" all
| errors should be notified by prep failing to return a descriptor
| handle. Negative dma_cookie_t values are only returned by the
| dma_async_memcpy* calls which translate a prep failure into -ENOMEM.
So remove the error handling at that point. This also solves the
potential deadlock mentioned in the previous comment.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As the DMA support introduces a separate interrupt-time callback, our
interrupt handler will not be the only handler which takes the port
lock, so we need to ensure that IRQs are disabled. We must use the
_irqsave variant so we don't inadvertently enable interrupts.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With DMA support, we need to tell the TTY subsystem that the DMA buffer
is the size of the FIFO, otherwise things like tty_wait_until_sent()
will time out too early. Keep (and use) the hardware value separately
from the port->fifosize.
This was part of a larger patch from Linus Walleij, with a little
modification.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than copying all vendor data into the port structure, copy
just that which is frequently used, and keep a pointer to the
remaining vendor data structure. This makes it easier to add
vendor quirks in the future.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The error flags weren't being cleared upon UART startup, which
can cause problems when we add DMA support. It's good practice
to ensure that these flags are cleared anyway, so let's do so.
This was part of a larger patch from Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include the revision number of the PL011 primecell in the boot-time
port printk to allow proper identification of the peripheral.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Not accessed outside builtin-script, so make them static.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
That already does what was being done here. The warning is now unconditionally
given by __perf_session__process_pipe_events, just like for non pipe processing.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Just like we do at __perf_session__process_events
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch fixes the usage of the perf_event.h header file
between command modules and the supporting code in util.
It is necessary to ensure that ALL files use the SAME
perf_event.h header from the kernel source tree.
There were a couple of #include <linux/perf_event.h> mixed
with #include "../../perf_event.h".
This caused issues on some distros because of mismatch
in the layout of struct perf_event_attr. That eventually
led perf stat to segfault.
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@gmail.com>
LKML-Reference: <4d233cf0.2308e30a.7b00.ffffc187@mx.google.com>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Rebooted my devel machine, first thing I ran was perf test, that expects
debugfs to be mounted, test fails. Be more clear about it.
Also add missing newlines and add more informative message when
sys_perf_event_open fails.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
drivers/staging/cx25821/cx25821-video.c: In function ‘video_open’:
drivers/staging/cx25821/cx25821-video.c:817:8: error: implicit declaration of function ‘lock_kernel’
drivers/staging/cx25821/cx25821-video.c:834:9: error: implicit declaration of function ‘unlock_kernel’
This patch just adds a header with BKL function. It should be enough
to avoid compilation breakage, but, as BKL will be removed, we need
to properly fix it on a latter patch.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Anca Emanuel <anca.emanuel@gmail.com>
Cc: Palash Bandyopadhyay <Palash.Bandyopadhyay@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent the long delay in io_check_error making NMI watchdog
timeout.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The spin_lock_debug/rcu_cpu_stall detector uses
trigger_all_cpu_backtrace() to dump cpu backtrace.
Therefore it is possible that trigger_all_cpu_backtrace()
could be called at the same time on different CPUs, which
triggers and 'unknown reason NMI' warning. The following case
illustrates the problem:
CPU1 CPU2 ... CPU N
trigger_all_cpu_backtrace()
set "backtrace_mask" to cpu mask
|
generate NMI interrupts generate NMI interrupts ...
\ | /
\ | /
The "backtrace_mask" will be cleaned by the first NMI interrupt
at nmi_watchdog_tick(), then the following NMI interrupts
generated by other cpus's arch_trigger_all_cpu_backtrace() will
be taken as unknown reason NMI interrupts.
This patch uses a test_and_set to avoid the problem, and stop
the arch_trigger_all_cpu_backtrace() from calling to avoid
dumping a double cpu backtrace info when there is already a
trigger_all_cpu_backtrace() in progress.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Reviewed-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Cc: fweisbec@gmail.com
LKML-Reference: <1294198689-15447-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Don Zickus <dzickus@redhat.com>
There are some paths that walk the die_chain with preemption on.
Make sure we are in an NMI call before we start doing anything.
This was triggered by do_general_protection calling notify_die
with DIE_GPF.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
wait_for_completion_*_timeout() can return:
0: if the wait timed out
-ve: if the wait was interrupted
+ve: if the completion was completed.
As they currently return an 'unsigned long', the last two cases
are not easily distinguished which can easily result in buggy
code, as is the case for the recently added
wait_for_completion_interruptible_timeout() call in
net/sunrpc/cache.c
So change them both to return 'long'. As MAX_SCHEDULE_TIMEOUT
is LONG_MAX, a large +ve return value should never overflow.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110105125016.64ccab0e@notabene.brown>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Found one x2apic pre-enabled system, x2apic_mode suddenly get
corrupted after register some cpus, when compiled
CONFIG_NR_CPUS=255 instead of 512.
It turns out that generic_processor_info() ==> phyid_set(apicid,
phys_cpu_present_map) causes the problem.
phys_cpu_present_map is sized by MAX_APICS bits, and pre-enabled
system some cpus have an apic id > 255.
The variable after phys_cpu_present_map may get corrupted
silently:
ffffffff828e8420 B phys_cpu_present_map
ffffffff828e8440 B apic_verbosity
ffffffff828e8444 B local_apic_timer_c2_ok
ffffffff828e8448 B disable_apic
ffffffff828e844c B x2apic_mode
ffffffff828e8450 B x2apic_disabled
ffffffff828e8454 B num_processors
...
Actually phys_cpu_present_map is referenced via apic id, instead
index. We should use MAX_LOCAL_APIC instead MAX_APICS.
For 64-bit it will be 32768 in all cases. BSS will increase by 4k bytes
on 64-bit:
text data bss dec filename
21696943 4193748 12787712 38678403 vmlinux.before
21696943 4193748 12791808 38682499 vmlinux.after
No change on 32bit.
Finally we can remove MAX_APCIS that was rather confusing.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4D23BD9C.3070102@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the seqfile /proc/cpuinfo gets accesses for each possible cpu
loops_per_jiffy gets recalculated. However its value is only needed
on first access.
In addition loops_per_jiffy should be recalculated when the machine
reports a capability change.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use get_online_cpus() instead of preempt_disable() to make sure cpus
don't go offline while accessing their per cpu data.
The preempt_disable() stuff is old code which was used before
get_online_cpus() was available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of messages that indicate if a cpu went online or offline.
There is nothing special about this anymore and these messages might
flood the kernel log buffer which makes debugging harder since more
important messages might be overwritten.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This enables the spinning mutex feature on s390 by removing
HAVE_DEFAULT_NO_SPIN_MUTEXES from arch/s390/Kconfig.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The spinning mutex implementation uses cpu_relax() in busy loops as a
compiler barrier. Depending on the architecture, cpu_relax() may do more
than needed in this specific mutex spin loops. On System z we also give
up the time slice of the virtual cpu in cpu_relax(), which prevents
effective spinning on the mutex.
This patch replaces cpu_relax() in the spinning mutex code with
arch_mutex_cpu_relax(), which can be defined by each architecture that
selects HAVE_ARCH_MUTEX_CPU_RELAX. The default is still cpu_relax(), so
this patch should not affect other architectures than System z for now.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290437256.7455.4.camel@thinkpad>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Magnus Damm