This is partial preparation for a future patch which will extend
ixgbe_set_num_queues
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
clean up the hardware shutdown sequence to prevent hardware
from continuing to send when resetting or unloading.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.
This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
in some configurations there can be more than one rx queue per vector
in msi-x mode. Add functionality to be able to clean this without
changing the performance path single-rx-queue cleanup.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
changing ring sizes in ethtool needs to be robust. If an allocation fails the
driver must continue operation, with the previous settings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
most of the time we only need 1500 bytes for a packet which means
we don't need a whole 4k page for each packet. Share the allocation
by using a reference count to the page and giving half to two
receive descriptors. This can enable us to use packet split mode
all the time due to the performance increase of allocating half
the pages.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe was incorrectly setting the throttle rate setting for all tx
queues and the driver has been refreshed to better handle a dynamic
interrupt mode as well as multiple queues.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Upon review a buglet was found where link change was not causing
an immediate link change event as it should.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch updates the link_up code and watchdog thread so that link_up
doesn't cause stack overflows due to long waits in interrupt context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change makes it so only one srrctl register is programmed per VMDq id, and if VMDq is not enabled it is one register per RSS queue. Currently this function is working correctly for the multiqueue RSS and single queue cases, but if any advances features such as VMDq or DCB would have been enabled this function would have caused issues as it was not correct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming. Hardware has separate registers internally for
storing these so use them.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hardware was configured incorrectly which led all hints to be
sent to queue[0]'s DCA configuration.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
correct CPU.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS. Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable Tx Head Writeback in the hardware. This helps performance by
removing adapter writebacks to descriptors on transmit completion.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.
Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none. This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit dropped the setting of the default interrupt throttle rate.
commit 021230d40a
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date: Mon Mar 3 15:03:45 2008 -0800
ixgbe: Introduce MSI-X queue vector code
The following patch adds it back. Without this the default value of 0
causes the performance of this card to be awful. Restoring these to the
default values yields much better performance.
This regression has been around since 2.6.25.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
VLAN filtering is broken, due to reading the incorrect register for
the VLAN filtering settings. Fixed by reading/writing the correct
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a simple device ID add for adapters that support
CX4 (copper infiniband style cable) connectors for 10GbE.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.
In addition, updated e1000e to use the updated tx mutliqueue api.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.
Non-multiqueue drivers need no changes. The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.
Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.
pktgen and netpoll required a little bit more surgery than the others.
In particular the pktgen changes, whilst functional, could be largely
improved. The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless. The thing to do is probably to
invoke fill_packet() earlier.
The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.
Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx(). If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.
Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.
With IGB changes from Jeff Kirsher.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a feature bit for something that
can be tested by simply checking the TX queue count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in this thread:
http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEh is not recovering in a resonable amount of time on PPC during
ixgbe_down().
Signed-off-by: Paul Larson <pl@us.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for in-kernel LRO with the ability to enable/disable via ethtool
based on comments from Ben Hutchings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
Tested this EEH patch with Intel 10G pci-express ixgbe adapter.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Under CONFIG_DCA the compilation is broken since the commit
bd0362dde0 (ixgbe: Add optional
DCA infrastructure).
IXGBE_SUCCESS is not defined anywhere, replace it with 0.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
82598 cards and up support DCA, which enables the chipset to warm
up the caches for upcoming payload data. This code makes the
driver plug into the CONFIG_DCA infrastructure that was merged
earlier.
Signed-off-by: Jeb Cramer <cramerj@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
82598 can produce a formidable interrupt rate, and is largely
unusable without some form of moderation. The default behaviour
before this patch is to limit irq's to a reasonable number.
However, just like our other drivers we can reduce latency
for small packet-type traffic considerably by allowing the
irq rate to go up dynamically.
This patch introduces a simple irq moderation algorithm based
on traffic analysis. The driver will use more CPU to service
small packets quicker but will perform the same on bulk traffic
as the old code.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that the irq vector code is in place, we can add the conditional
multiqueue TX code in the driver. This requires the optional
CONFIG_NETDEVICES_MULTIQUEUE=y and will not be enabled without
it.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Waskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jesse Brandeburg
Jeff Kirsher
David S. Miller
Alexander Duyck
PJ Waskiewicz
Christopher Leech
Andy Gospodarek
Patrick McHardy
Paul Larson
Mallikarjuna R Chilakala
Wendy Xiong
Denis V. Lunev
Auke Kok
Jeb Cramer
Ayyappan Veeraiyan