Commit Graph

940 Commits

Author SHA1 Message Date
Christoffer Dall fdec12c12e KVM: arm/arm64: vgic: Fix kvm_vgic_map_is_active's dist check
External inputs to the vgic from time to time need to poke into the
state of a virtual interrupt, the prime example is the architected timer
code.

Since the IRQ's active state can be represented in two places; the LR or
the distributor, we first loop over the LRs but if not active in the LRs
we just return if *any* IRQ is active on the VCPU in question.

This is of course bogus, as we should check if the specific IRQ in
quesiton is active on the distributor instead.

Reported-by: Eric Auger <eric.auger@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-12-11 16:33:31 +00:00
Christoffer Dall 9f958c11b7 KVM: arm/arm64: vgic: Trust the LR state for HW IRQs
We were probing the physial distributor state for the active state of a
HW virtual IRQ, because we had seen evidence that the LR state was not
cleared when the guest deactivated a virtual interrupted.

However, this issue turned out to be a software bug in the GIC, which
was solved by: 84aab5e68c2a5e1e18d81ae8308c3ce25d501b29
(KVM: arm/arm64: arch_timer: Preserve physical dist. active
state on LR.active, 2015-11-24)

Therefore, get rid of the complexities and just look at the LR.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-24 18:08:37 +01:00
Christoffer Dall 0e3dfda91d KVM: arm/arm64: arch_timer: Preserve physical dist. active state on LR.active
We were incorrectly removing the active state from the physical
distributor on the timer interrupt when the timer output level was
deasserted.  We shouldn't be doing this without considering the virtual
interrupt's active state, because the architecture requires that when an
LR has the HW bit set and the pending or active bits set, then the
physical interrupt must also have the corresponding bits set.

This addresses an issue where we have been observing an inconsistency
between the LR state and the physical distributor state where the LR
state was active and the physical distributor was not active, which
shouldn't happen.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-24 18:07:40 +01:00
Linus Torvalds 933425fb00 s390: A bunch of fixes and optimizations for interrupt and time
handling.
 
 PPC: Mostly bug fixes.
 
 ARM: No big features, but many small fixes and prerequisites including:
 - a number of fixes for the arch-timer
 - introducing proper level-triggered semantics for the arch-timers
 - a series of patches to synchronously halt a guest (prerequisite for
   IRQ forwarding)
 - some tracepoint improvements
 - a tweak for the EL2 panic handlers
 - some more VGIC cleanups getting rid of redundant state
 
 x86: quite a few changes:
 
 - support for VT-d posted interrupts (i.e. PCI devices can inject
 interrupts directly into vCPUs).  This introduces a new component (in
 virt/lib/) that connects VFIO and KVM together.  The same infrastructure
 will be used for ARM interrupt forwarding as well.
 
 - more Hyper-V features, though the main one Hyper-V synthetic interrupt
 controller will have to wait for 4.5.  These will let KVM expose Hyper-V
 devices.
 
 - nested virtualization now supports VPID (same as PCID but for vCPUs)
 which makes it quite a bit faster
 
 - for future hardware that supports NVDIMM, there is support for clflushopt,
 clwb, pcommit
 
 - support for "split irqchip", i.e. LAPIC in kernel + IOAPIC/PIC/PIT in
 userspace, which reduces the attack surface of the hypervisor
 
 - obligatory smattering of SMM fixes
 
 - on the guest side, stable scheduler clock support was rewritten to not
 require help from the hypervisor.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQEcBAABAgAGBQJWO2IQAAoJEL/70l94x66D/K0H/3AovAgYmJQToZlimsktMk6a
 f2xhdIqfU5lIQQh5uNBCfL3o9o8H9Py1ym7aEw3fmztPHHJYc91oTatt2UEKhmEw
 VtZHp/dFHt3hwaIdXmjRPEXiYctraKCyrhaUYdWmUYkoKi7lW5OL5h+S7frG2U6u
 p/hFKnHRZfXHr6NSgIqvYkKqtnc+C0FWY696IZMzgCksOO8jB1xrxoSN3tANW3oJ
 PDV+4og0fN/Fr1capJUFEc/fejREHneANvlKrLaa8ht0qJQutoczNADUiSFLcMPG
 iHljXeDsv5eyjMtUuIL8+MPzcrIt/y4rY41ZPiKggxULrXc6H+JJL/e/zThZpXc=
 =iv2z
 -----END PGP SIGNATURE-----

Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm

Pull KVM updates from Paolo Bonzini:
 "First batch of KVM changes for 4.4.

  s390:
     A bunch of fixes and optimizations for interrupt and time handling.

  PPC:
     Mostly bug fixes.

  ARM:
     No big features, but many small fixes and prerequisites including:

      - a number of fixes for the arch-timer

      - introducing proper level-triggered semantics for the arch-timers

      - a series of patches to synchronously halt a guest (prerequisite
        for IRQ forwarding)

      - some tracepoint improvements

      - a tweak for the EL2 panic handlers

      - some more VGIC cleanups getting rid of redundant state

  x86:
     Quite a few changes:

      - support for VT-d posted interrupts (i.e. PCI devices can inject
        interrupts directly into vCPUs).  This introduces a new
        component (in virt/lib/) that connects VFIO and KVM together.
        The same infrastructure will be used for ARM interrupt
        forwarding as well.

      - more Hyper-V features, though the main one Hyper-V synthetic
        interrupt controller will have to wait for 4.5.  These will let
        KVM expose Hyper-V devices.

      - nested virtualization now supports VPID (same as PCID but for
        vCPUs) which makes it quite a bit faster

      - for future hardware that supports NVDIMM, there is support for
        clflushopt, clwb, pcommit

      - support for "split irqchip", i.e.  LAPIC in kernel +
        IOAPIC/PIC/PIT in userspace, which reduces the attack surface of
        the hypervisor

      - obligatory smattering of SMM fixes

      - on the guest side, stable scheduler clock support was rewritten
        to not require help from the hypervisor"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (123 commits)
  KVM: VMX: Fix commit which broke PML
  KVM: x86: obey KVM_X86_QUIRK_CD_NW_CLEARED in kvm_set_cr0()
  KVM: x86: allow RSM from 64-bit mode
  KVM: VMX: fix SMEP and SMAP without EPT
  KVM: x86: move kvm_set_irq_inatomic to legacy device assignment
  KVM: device assignment: remove pointless #ifdefs
  KVM: x86: merge kvm_arch_set_irq with kvm_set_msi_inatomic
  KVM: x86: zero apic_arb_prio on reset
  drivers/hv: share Hyper-V SynIC constants with userspace
  KVM: x86: handle SMBASE as physical address in RSM
  KVM: x86: add read_phys to x86_emulate_ops
  KVM: x86: removing unused variable
  KVM: don't pointlessly leave KVM_COMPAT=y in non-KVM configs
  KVM: arm/arm64: Merge vgic_set_lr() and vgic_sync_lr_elrsr()
  KVM: arm/arm64: Clean up vgic_retire_lr() and surroundings
  KVM: arm/arm64: Optimize away redundant LR tracking
  KVM: s390: use simple switch statement as multiplexer
  KVM: s390: drop useless newline in debugging data
  KVM: s390: SCA must not cross page boundaries
  KVM: arm: Do not indent the arguments of DECLARE_BITMAP
  ...
2015-11-05 16:26:26 -08:00
Paolo Bonzini b97e6de9c9 KVM: x86: merge kvm_arch_set_irq with kvm_set_msi_inatomic
We do not want to do too much work in atomic context, in particular
not walking all the VCPUs of the virtual machine.  So we want
to distinguish the architecture-specific injection function for irqfd
from kvm_set_msi.  Since it's still empty, reuse the newly added
kvm_arch_set_irq and rename it to kvm_arch_set_irq_inatomic.

Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-11-04 16:24:35 +01:00
Jan Beulich 6956d8946d KVM: don't pointlessly leave KVM_COMPAT=y in non-KVM configs
The symbol was missing a KVM dependency.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-11-04 16:24:30 +01:00
Paolo Bonzini 197a4f4b06 KVM/ARM Changes for v4.4-rc1
Includes a number of fixes for the arch-timer, introducing proper
 level-triggered semantics for the arch-timers, a series of patches to
 synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
 improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
 getting rid of redundant state, and finally a stylistic change that gets rid of
 some ctags warnings.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJWOhgAAAoJEEtpOizt6ddyKS8H/2ZHMTPjo6yChnrusNWy4Qbr
 6laPDlzL+g45oMQRwNL7GnM1deRftaxvT2Wi+X84D/6Y/BD6MPds4HgtBfuWcSZ1
 CyRJ0Ot/zrxenucSuJuOjq+a9gdizdAczkbB1MfYDULJH8fb6D+7RYLo3zgh4Xo4
 pla3L9U6gSWe+YopBjZtZH43m3fwiwSM/v+uHOTIcXrsbR+fEgx/EFSKmA/DUCuo
 P5cFO/ceUGu7nATCexu5V82TgR2hvurrsR7mqfwY8YcF6HRM+NEOoS29xWC77v5S
 u/F08TKuKQLv0YTEFTyLETI/oEeuC0cHtrRQBNf4+9kXEOzKyXaae0wR/I6X2Ss=
 =GMNk
 -----END PGP SIGNATURE-----

Merge tag 'kvm-arm-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/ARM Changes for v4.4-rc1

Includes a number of fixes for the arch-timer, introducing proper
level-triggered semantics for the arch-timers, a series of patches to
synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
getting rid of redundant state, and finally a stylistic change that gets rid of
some ctags warnings.

Conflicts:
	arch/x86/include/asm/kvm_host.h
2015-11-04 16:24:17 +01:00
Pavel Fedin 26caea7693 KVM: arm/arm64: Merge vgic_set_lr() and vgic_sync_lr_elrsr()
Now we see that vgic_set_lr() and vgic_sync_lr_elrsr() are always used
together. Merge them into one function, saving from second vgic_ops
dereferencing every time.

Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-04 15:29:49 +01:00
Pavel Fedin 212c76545d KVM: arm/arm64: Clean up vgic_retire_lr() and surroundings
1. Remove unnecessary 'irq' argument, because irq number can be retrieved
   from the LR.
2. Since cff9211eb1
   ("arm/arm64: KVM: Fix arch timer behavior for disabled interrupts ")
   LR_STATE_PENDING is queued back by vgic_retire_lr() itself. Also, it
   clears vlr.state itself. Therefore, we remove the same, now duplicated,
   check with all accompanying bit manipulations from vgic_unqueue_irqs().
3. vgic_retire_lr() is always accompanied by vgic_irq_clear_queued(). Since
   it already does more than just clearing the LR, move
   vgic_irq_clear_queued() inside of it.

Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-04 15:29:49 +01:00
Pavel Fedin c4cd4c168b KVM: arm/arm64: Optimize away redundant LR tracking
Currently we use vgic_irq_lr_map in order to track which LRs hold which
IRQs, and lr_used bitmap in order to track which LRs are used or free.

vgic_irq_lr_map is actually used only for piggy-back optimization, and
can be easily replaced by iteration over lr_used. This is good because in
future, when LPI support is introduced, number of IRQs will grow up to at
least 16384, while numbers from 1024 to 8192 are never going to be used.
This would be a huge memory waste.

In its turn, lr_used is also completely redundant since
ae705930fc ("arm/arm64: KVM: Keep elrsr/aisr
in sync with software model"), because together with lr_used we also update
elrsr. This allows to easily replace lr_used with elrsr, inverting all
conditions (because in elrsr '1' means 'free').

Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-11-04 15:29:49 +01:00
Linus Torvalds 6aa2fdb87c Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
 "The irq departement delivers:

   - Rework the irqdomain core infrastructure to accomodate ACPI based
     systems.  This is required to support ARM64 without creating
     artificial device tree nodes.

   - Sanitize the ACPI based ARM GIC initialization by making use of the
     new firmware independent irqdomain core

   - Further improvements to the generic MSI management

   - Generalize the irq migration on CPU hotplug

   - Improvements to the threaded interrupt infrastructure

   - Allow the migration of "chained" low level interrupt handlers

   - Allow optional force masking of interrupts in disable_irq[_nosysnc]

   - Support for two new interrupt chips - Sigh!

   - A larger set of errata fixes for ARM gicv3

   - The usual pile of fixes, updates, improvements and cleanups all
     over the place"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
  Document that IRQ_NONE should be returned when IRQ not actually handled
  PCI/MSI: Allow the MSI domain to be device-specific
  PCI: Add per-device MSI domain hook
  of/irq: Use the msi-map property to provide device-specific MSI domain
  of/irq: Split of_msi_map_rid to reuse msi-map lookup
  irqchip/gic-v3-its: Parse new version of msi-parent property
  PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
  of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
  of/irq: Add support code for multi-parent version of "msi-parent"
  irqchip/gic-v3-its: Add handling of PCI requester id.
  PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
  of/irq: Add new function of_msi_map_rid()
  Docs: dt: Add PCI MSI map bindings
  irqchip/gic-v2m: Add support for multiple MSI frames
  irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
  irqchip/mxs: Add Alphascale ASM9260 support
  irqchip/mxs: Prepare driver for hardware with different offsets
  irqchip/mxs: Panic if ioremap or domain creation fails
  irqdomain: Documentation updates
  irqdomain/msi: Use fwnode instead of of_node
  ...
2015-11-03 14:40:01 -08:00
Christoffer Dall e21f091087 arm/arm64: KVM: Add tracepoints for vgic and timer
The VGIC and timer code for KVM arm/arm64 doesn't have any tracepoints
or tracepoint infrastructure defined.  Rewriting some of the timer code
handling showed me how much we need this, so let's add these simple
trace points once and for all and we can easily expand with additional
trace points in these files as we go along.

Cc: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:48 +02:00
Christoffer Dall 8fe2f19e6e arm/arm64: KVM: Support edge-triggered forwarded interrupts
We mark edge-triggered interrupts with the HW bit set as queued to
prevent the VGIC code from injecting LRs with both the Active and
Pending bits set at the same time while also setting the HW bit,
because the hardware does not support this.

However, this means that we must also clear the queued flag when we sync
back a LR where the state on the physical distributor went from active
to inactive because the guest deactivated the interrupt.  At this point
we must also check if the interrupt is pending on the distributor, and
tell the VGIC to queue it again if it is.

Since these actions on the sync path are extremely close to those for
level-triggered interrupts, rename process_level_irq to
process_queued_irq, allowing it to cater for both cases.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:44 +02:00
Christoffer Dall 4b4b4512da arm/arm64: KVM: Rework the arch timer to use level-triggered semantics
The arch timer currently uses edge-triggered semantics in the sense that
the line is never sampled by the vgic and lowering the line from the
timer to the vgic doesn't have any effect on the pending state of
virtual interrupts in the vgic.  This means that we do not support a
guest with the otherwise valid behavior of (1) disable interrupts (2)
enable the timer (3) disable the timer (4) enable interrupts.  Such a
guest would validly not expect to see any interrupts on real hardware,
but will see interrupts on KVM.

This patch fixes this shortcoming through the following series of
changes.

First, we change the flow of the timer/vgic sync/flush operations.  Now
the timer is always flushed/synced before the vgic, because the vgic
samples the state of the timer output.  This has the implication that we
move the timer operations in to non-preempible sections, but that is
fine after the previous commit getting rid of hrtimer schedules on every
entry/exit.

Second, we change the internal behavior of the timer, letting the timer
keep track of its previous output state, and only lower/raise the line
to the vgic when the state changes.  Note that in theory this could have
been accomplished more simply by signalling the vgic every time the
state *potentially* changed, but we don't want to be hitting the vgic
more often than necessary.

Third, we get rid of the use of the map->active field in the vgic and
instead simply set the interrupt as active on the physical distributor
whenever the input to the GIC is asserted and conversely clear the
physical active state when the input to the GIC is deasserted.

Fourth, and finally, we now initialize the timer PPIs (and all the other
unused PPIs for now), to be level-triggered, and modify the sync code to
sample the line state on HW sync and re-inject a new interrupt if it is
still pending at that time.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:44 +02:00
Christoffer Dall 54723bb37f arm/arm64: KVM: Use appropriate define in VGIC reset code
We currently initialize the SGIs to be enabled in the VGIC code, but we
use the VGIC_NR_PPIS define for this purpose, instead of the the more
natural VGIC_NR_SGIS.  Change this slightly confusing use of the
defines.

Note: This should have no functional change, as both names are defined
to the number 16.

Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:43 +02:00
Christoffer Dall 8bf9a701e1 arm/arm64: KVM: Implement GICD_ICFGR as RO for PPIs
The GICD_ICFGR allows the bits for the SGIs and PPIs to be read only.
We currently simulate this behavior by writing a hardcoded value to the
register for the SGIs and PPIs on every write of these bits to the
register (ignoring what the guest actually wrote), and by writing the
same value as the reset value to the register.

This is a bit counter-intuitive, as the register is RO for these bits,
and we can just implement it that way, allowing us to control the value
of the bits purely in the reset code.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:42 +02:00
Christoffer Dall 9103617df2 arm/arm64: KVM: vgic: Factor out level irq processing on guest exit
Currently vgic_process_maintenance() processes dealing with a completed
level-triggered interrupt directly, but we are soon going to reuse this
logic for level-triggered mapped interrupts with the HW bit set, so
move this logic into a separate static function.

Probably the most scary part of this commit is convincing yourself that
the current flow is safe compared to the old one.  In the following I
try to list the changes and why they are harmless:

  Move vgic_irq_clear_queued after kvm_notify_acked_irq:
    Harmless because the only potential effect of clearing the queued
    flag wrt.  kvm_set_irq is that vgic_update_irq_pending does not set
    the pending bit on the emulated CPU interface or in the
    pending_on_cpu bitmask if the function is called with level=1.
    However, the point of kvm_notify_acked_irq is to call kvm_set_irq
    with level=0, and we set the queued flag again in
    __kvm_vgic_sync_hwstate later on if the level is stil high.

  Move vgic_set_lr before kvm_notify_acked_irq:
    Also, harmless because the LR are cpu-local operations and
    kvm_notify_acked only affects the dist

  Move vgic_dist_irq_clear_soft_pend after kvm_notify_acked_irq:
    Also harmless, because now we check the level state in the
    clear_soft_pend function and lower the pending bits if the level is
    low.

Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:42 +02:00
Christoffer Dall d35268da66 arm/arm64: KVM: arch_timer: Only schedule soft timer on vcpu_block
We currently schedule a soft timer every time we exit the guest if the
timer did not expire while running the guest.  This is really not
necessary, because the only work we do in the timer work function is to
kick the vcpu.

Kicking the vcpu does two things:
(1) If the vpcu thread is on a waitqueue, make it runnable and remove it
from the waitqueue.
(2) If the vcpu is running on a different physical CPU from the one
doing the kick, it sends a reschedule IPI.

The second case cannot happen, because the soft timer is only ever
scheduled when the vcpu is not running.  The first case is only relevant
when the vcpu thread is on a waitqueue, which is only the case when the
vcpu thread has called kvm_vcpu_block().

Therefore, we only need to make sure a timer is scheduled for
kvm_vcpu_block(), which we do by encapsulating all calls to
kvm_vcpu_block() with kvm_timer_{un}schedule calls.

Additionally, we only schedule a soft timer if the timer is enabled and
unmasked, since it is useless otherwise.

Note that theoretically userspace can use the SET_ONE_REG interface to
change registers that should cause the timer to fire, even if the vcpu
is blocked without a scheduled timer, but this case was not supported
before this patch and we leave it for future work for now.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:42 +02:00
Christoffer Dall 3217f7c25b KVM: Add kvm_arch_vcpu_{un}blocking callbacks
Some times it is useful for architecture implementations of KVM to know
when the VCPU thread is about to block or when it comes back from
blocking (arm/arm64 needs to know this to properly implement timers, for
example).

Therefore provide a generic architecture callback function in line with
what we do elsewhere for KVM generic-arch interactions.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-22 23:01:41 +02:00
Christoffer Dall 0d997491f8 arm/arm64: KVM: Fix disabled distributor operation
We currently do a single update of the vgic state when the distributor
enable/disable control register is accessed and then bypass updating the
state for as long as the distributor remains disabled.

This is incorrect, because updating the state does not consider the
distributor enable bit, and this you can end up in a situation where an
interrupt is marked as pending on the CPU interface, but not pending on
the distributor, which is an impossible state to be in, and triggers a
warning.  Consider for example the following sequence of events:

1. An interrupt is marked as pending on the distributor
   - the interrupt is also forwarded to the CPU interface
2. The guest turns off the distributor (it's about to do a reboot)
   - we stop updating the CPU interface state from now on
3. The guest disables the pending interrupt
   - we remove the pending state from the distributor, but don't touch
     the CPU interface, see point 2.

Since the distributor disable bit really means that no interrupts should
be forwarded to the CPU interface, we modify the code to keep updating
the internal VGIC state, but always set the CPU interface pending bits
to zero when the distributor is disabled.

Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-20 18:09:13 +02:00
Christoffer Dall 544c572e03 arm/arm64: KVM: Clear map->active on pend/active clear
When a guest reboots or offlines/onlines CPUs, it is not uncommon for it
to clear the pending and active states of an interrupt through the
emulated VGIC distributor.  However, since the architected timers are
defined by the architecture to be level triggered and the guest
rightfully expects them to be that, but we emulate them as
edge-triggered, we have to mimic level-triggered behavior for an
edge-triggered virtual implementation.

We currently do not signal the VGIC when the map->active field is true,
because it indicates that the guest has already been signalled of the
interrupt as required.  Normally this field is set to false when the
guest deactivates the virtual interrupt through the sync path.

We also need to catch the case where the guest deactivates the interrupt
through the emulated distributor, again allowing guests to boot even if
the original virtual timer signal hit before the guest's GIC
initialization sequence is run.

Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-20 18:06:34 +02:00
Christoffer Dall cff9211eb1 arm/arm64: KVM: Fix arch timer behavior for disabled interrupts
We have an interesting issue when the guest disables the timer interrupt
on the VGIC, which happens when turning VCPUs off using PSCI, for
example.

The problem is that because the guest disables the virtual interrupt at
the VGIC level, we never inject interrupts to the guest and therefore
never mark the interrupt as active on the physical distributor.  The
host also never takes the timer interrupt (we only use the timer device
to trigger a guest exit and everything else is done in software), so the
interrupt does not become active through normal means.

The result is that we keep entering the guest with a programmed timer
that will always fire as soon as we context switch the hardware timer
state and run the guest, preventing forward progress for the VCPU.

Since the active state on the physical distributor is really part of the
timer logic, it is the job of our virtual arch timer driver to manage
this state.

The timer->map->active boolean field indicates whether we have signalled
this interrupt to the vgic and if that interrupt is still pending or
active.  As long as that is the case, the hardware doesn't have to
generate physical interrupts and therefore we mark the interrupt as
active on the physical distributor.

We also have to restore the pending state of an interrupt that was
queued to an LR but was retired from the LR for some reason, while
remaining pending in the LR.

Cc: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-20 18:04:54 +02:00
Pavel Fedin 437f9963bc KVM: arm/arm64: Do not inject spurious interrupts
When lowering a level-triggered line from userspace, we forgot to lower
the pending bit on the emulated CPU interface and we also did not
re-compute the pending_on_cpu bitmap for the CPU affected by the change.

Update vgic_update_irq_pending() to fix the two issues above and also
raise a warning in vgic_quue_irq_to_lr if we encounter an interrupt
pending on a CPU which is neither marked active nor pending.

  [ Commit text reworked completely - Christoffer ]

Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
2015-10-20 18:04:43 +02:00
Andrey Smetanin f33143d809 kvm/irqchip: allow only multiple irqchip routes per GSI
Any other irq routing types (MSI, S390_ADAPTER, upcoming Hyper-V
SynIC) map one-to-one to GSI.

Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-16 10:34:30 +02:00
Andrey Smetanin c9a5eccac1 kvm/eventfd: add arch-specific set_irq
Allow for arch-specific interrupt types to be set.  For that, add
kvm_arch_set_irq() which takes interrupt type-specific action if it
recognizes the interrupt type given, and -EWOULDBLOCK otherwise.

The default implementation always returns -EWOULDBLOCK.

Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-16 10:34:29 +02:00
Andrey Smetanin ba1aefcd6d kvm/eventfd: factor out kvm_notify_acked_gsi()
Factor out kvm_notify_acked_gsi() helper to iterate over EOI listeners
and notify those matching the given gsi.

It will be reused in the upcoming Hyper-V SynIC implementation.

Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-16 10:34:29 +02:00
Andrey Smetanin 351dc6477c kvm/eventfd: avoid loop inside irqfd_update()
The loop(for) inside irqfd_update() is unnecessary
because any other value for irq_entry.type will just trigger
schedule_work(&irqfd->inject) in irqfd_wakeup.

Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-16 10:34:28 +02:00
Kosuke Tatsukawa 6003a42010 kvm: fix waitqueue_active without memory barrier in virt/kvm/async_pf.c
async_pf_execute() seems to be missing a memory barrier which might
cause the waker to not notice the waiter and miss sending a wake_up as
in the following figure.

        async_pf_execute                    kvm_vcpu_block
------------------------------------------------------------------------
spin_lock(&vcpu->async_pf.lock);
if (waitqueue_active(&vcpu->wq))
/* The CPU might reorder the test for
   the waitqueue up here, before
   prior writes complete */
                                    prepare_to_wait(&vcpu->wq, &wait,
                                      TASK_INTERRUPTIBLE);
                                    /*if (kvm_vcpu_check_block(vcpu) < 0) */
                                     /*if (kvm_arch_vcpu_runnable(vcpu)) { */
                                      ...
                                      return (vcpu->arch.mp_state == KVM_MP_STATE_RUNNABLE &&
                                        !vcpu->arch.apf.halted)
                                        || !list_empty_careful(&vcpu->async_pf.done)
                                     ...
                                     return 0;
list_add_tail(&apf->link,
  &vcpu->async_pf.done);
spin_unlock(&vcpu->async_pf.lock);
                                    waited = true;
                                    schedule();
------------------------------------------------------------------------

The attached patch adds the missing memory barrier.

I found this issue when I was looking through the linux source code
for places calling waitqueue_active() before wake_up*(), but without
preceding memory barriers, after sending a patch to fix a similar
issue in drivers/tty/n_tty.c  (Details about the original issue can be
found here: https://lkml.org/lkml/2015/9/28/849).

Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-14 16:41:08 +02:00
Jean-Philippe Brucker 4f64cb65bf arm/arm64: KVM: Only allow 64bit hosts to build VGICv3
Hardware virtualisation of GICv3 is only supported by 64bit hosts for
the moment. Some VGICv3 bits are missing from the 32bit side, and this
patch allows to still be able to build 32bit hosts when CONFIG_ARM_GIC_V3
is selected.

To this end, we introduce a new option, CONFIG_KVM_ARM_VGIC_V3, that is
only enabled on the 64bit side. The selection is done unconditionally
because CONFIG_ARM_GIC_V3 is always enabled on arm64.

Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-10-09 23:11:57 +01:00
Feng Wu bf9f6ac8d7 KVM: Update Posted-Interrupts Descriptor when vCPU is blocked
This patch updates the Posted-Interrupts Descriptor when vCPU
is blocked.

pre-block:
- Add the vCPU to the blocked per-CPU list
- Set 'NV' to POSTED_INTR_WAKEUP_VECTOR

post-block:
- Remove the vCPU from the per-CPU list

Signed-off-by: Feng Wu <feng.wu@intel.com>
[Concentrate invocation of pre/post-block hooks to vcpu_block. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:53 +02:00
Feng Wu f70c20aaf1 KVM: Add an arch specific hooks in 'struct kvm_kernel_irqfd'
This patch adds an arch specific hooks 'arch_update' in
'struct kvm_kernel_irqfd'. On Intel side, it is used to
update the IRTE when VT-d posted-interrupts is used.

Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:47 +02:00
Eric Auger 9016cfb577 KVM: eventfd: add irq bypass consumer management
This patch adds the registration/unregistration of an
irq_bypass_consumer on irqfd assignment/deassignment.

Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:46 +02:00
Eric Auger 1a02b27035 KVM: introduce kvm_arch functions for IRQ bypass
This patch introduces
- kvm_arch_irq_bypass_add_producer
- kvm_arch_irq_bypass_del_producer
- kvm_arch_irq_bypass_stop
- kvm_arch_irq_bypass_start

They make possible to specialize the KVM IRQ bypass consumer in
case CONFIG_KVM_HAVE_IRQ_BYPASS is set.

Signed-off-by: Eric Auger <eric.auger@linaro.org>
[Add weak implementations of the callbacks. - Feng]
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:45 +02:00
Eric Auger 166c9775f1 KVM: create kvm_irqfd.h
Move _irqfd_resampler and _irqfd struct declarations in a new
public header: kvm_irqfd.h. They are respectively renamed into
kvm_kernel_irqfd_resampler and kvm_kernel_irqfd. Those datatypes
will be used by architecture specific code, in the context of
IRQ bypass manager integration.

Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:44 +02:00
Feng Wu 37d9fe4783 virt: Add virt directory to the top Makefile
We need to build files in virt/lib/, which are now used by
KVM and VFIO, so add virt directory to the top Makefile.

Signed-off-by: Feng Wu <feng.wu@intel.com>
Acked-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:44 +02:00
Alex Williamson f73f817312 virt: IRQ bypass manager
When a physical I/O device is assigned to a virtual machine through
facilities like VFIO and KVM, the interrupt for the device generally
bounces through the host system before being injected into the VM.
However, hardware technologies exist that often allow the host to be
bypassed for some of these scenarios.  Intel Posted Interrupts allow
the specified physical edge interrupts to be directly injected into a
guest when delivered to a physical processor while the vCPU is
running.  ARM IRQ Forwarding allows forwarded physical interrupts to
be directly deactivated by the guest.

The IRQ bypass manager here is meant to provide the shim to connect
interrupt producers, generally the host physical device driver, with
interrupt consumers, generally the hypervisor, in order to configure
these bypass mechanism.  To do this, we base the connection on a
shared, opaque token.  For KVM-VFIO this is expected to be an
eventfd_ctx since this is the connection we already use to connect an
eventfd to an irqfd on the in-kernel path.  When a producer and
consumer with matching tokens is found, callbacks via both registered
participants allow the bypass facilities to be automatically enabled.

Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:43 +02:00
Jason Wang e9ea5069d9 kvm: add capability for any-length ioeventfds
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:31 +02:00
Jason Wang d3febddde9 kvm: use kmalloc() instead of kzalloc() during iodev register/unregister
All fields of kvm_io_range were initialized or copied explicitly
afterwards. So switch to use kmalloc().

Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:29 +02:00
Steve Rutherford b053b2aef2 KVM: x86: Add EOI exit bitmap inference
In order to support a userspace IOAPIC interacting with an in kernel
APIC, the EOI exit bitmaps need to be configurable.

If the IOAPIC is in userspace (i.e. the irqchip has been split), the
EOI exit bitmaps will be set whenever the GSI Routes are configured.
In particular, for the low MSI routes are reservable for userspace
IOAPICs. For these MSI routes, the EOI Exit bit corresponding to the
destination vector of the route will be set for the destination VCPU.

The intention is for the userspace IOAPICs to use the reservable MSI
routes to inject interrupts into the guest.

This is a slight abuse of the notion of an MSI Route, given that MSIs
classically bypass the IOAPIC. It might be worthwhile to add an
additional route type to improve clarity.

Compile tested for Intel x86.

Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-10-01 15:06:28 +02:00
David Hildenbrand 920552b213 KVM: disable halt_poll_ns as default for s390x
We observed some performance degradation on s390x with dynamic
halt polling. Until we can provide a proper fix, let's enable
halt_poll_ns as default only for supported architectures.

Architectures are now free to set their own halt_poll_ns
default value.

Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-25 10:31:30 +02:00
Paolo Bonzini efe4d36a75 Second set of KVM/ARM changes for 4.3-rc2
- Workaround for a Cortex-A57 erratum
 - Bug fix for the debugging infrastructure
 - Fix for 32bit guests with more than 4GB of address space
   on a 32bit host
 - A number of fixes for the (unusual) case when we don't use
   the in-kernel GIC emulation
 - Removal of ThumbEE handling on arm64, since these have been
   dropped from the architecture before anyone actually ever
   built a CPU
 - Remove the KVM_ARM_MAX_VCPUS limitation which has become
   fairly pointless
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJV+slQAAoJECPQ0LrRPXpD+WUQAMLC3ZUasJX1gsVixd++zAwB
 FXu0TFlKCUsLWllXZtyhGI6ya7ljuCzfhRbA/eZFmFVbwDnULt1p5ahw7eHCIZ2a
 yY93TS6XN3YHwVpY7f2lDsvLhBLyWeTdWhj5TtLy6mslQyEUqxdmsiC7gl40Fp2S
 8tKIxoYYRpmbgKl/Lbi8GxdHH6c0aQ2Nt7Fq4nV9dJqy5tiGdg6OxqgU/rVmkdkv
 Rv1jrdtncstNRi9NBbKRRDp5DTqWboF35HJQpdIRpR8jJTLuuzzCimP5Hz9crKuO
 uXchIq2GtQB60NklZtPL15zMdmfdq+JHwdC14v05kB5Ai8NThGwKYQ3JF+krO3cG
 RKsAlrIq0AwPN8hAboLcKGzjLFFryaHZsa+d7elxaaDQz1FGz4uP56fIUURoGZuX
 vWTsKLRKcuPCYtnV6Frg2BCTB6nq1cRgjmMC9TABnraelZ3z0lDl4wFngg4aL2u6
 QYOdP8L++/S1HAPOF7VhFYndXkbM3KoVLAepev8jvzRnwg4QVrqsvfgwFSdMNcMz
 ga7bJ4pUEP+Qq1i0qc41P9O708bCGm7TIw3CzTdKIZhc/l0t137lw1rhv67JfXZh
 cAni4osjhpdZUT0F9lIl/6OQB3Kgk6on3cs909Y/tT1srh9s+iVO1AwpGY1j5T4j
 gFRy90o2LBuepoI/8yF3
 =NNtz
 -----END PGP SIGNATURE-----

Merge tag 'kvm-arm-for-4.3-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master

Second set of KVM/ARM changes for 4.3-rc2

- Workaround for a Cortex-A57 erratum
- Bug fix for the debugging infrastructure
- Fix for 32bit guests with more than 4GB of address space
  on a 32bit host
- A number of fixes for the (unusual) case when we don't use
  the in-kernel GIC emulation
- Removal of ThumbEE handling on arm64, since these have been
  dropped from the architecture before anyone actually ever
  built a CPU
- Remove the KVM_ARM_MAX_VCPUS limitation which has become
  fairly pointless
2015-09-17 16:51:59 +02:00
Ming Lei ef748917b5 arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
This patch removes config option of KVM_ARM_MAX_VCPUS,
and like other ARCHs, just choose the maximum allowed
value from hardware, and follows the reasons:

1) from distribution view, the option has to be
defined as the max allowed value because it need to
meet all kinds of virtulization applications and
need to support most of SoCs;

2) using a bigger value doesn't introduce extra memory
consumption, and the help text in Kconfig isn't accurate
because kvm_vpu structure isn't allocated until request
of creating VCPU is sent from QEMU;

3) the main effect is that the field of vcpus[] in 'struct kvm'
becomes a bit bigger(sizeof(void *) per vcpu) and need more cache
lines to hold the structure, but 'struct kvm' is one generic struct,
and it has worked well on other ARCHs already in this way. Also,
the world switch frequecy is often low, for example, it is ~2000
when running kernel building load in VM from APM xgene KVM host,
so the effect is very small, and the difference can't be observed
in my test at all.

Cc: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2015-09-17 13:13:27 +01:00
Paolo Bonzini 62bea5bff4 KVM: add halt_attempted_poll to VCPU stats
This new statistic can help diagnosing VCPUs that, for any reason,
trigger bad behavior of halt_poll_ns autotuning.

For example, say halt_poll_ns = 480000, and wakeups are spaced exactly
like 479us, 481us, 479us, 481us. Then KVM always fails polling and wastes
10+20+40+80+160+320+480 = 1110 microseconds out of every
479+481+479+481+479+481+479 = 3359 microseconds. The VCPU then
is consuming about 30% more CPU than it would use without
polling.  This would show as an abnormally high number of
attempted polling compared to the successful polls.

Acked-by: Christian Borntraeger <borntraeger@de.ibm.com<
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-16 12:17:00 +02:00
Jason Wang 8f4216c7d2 kvm: fix zero length mmio searching
Currently, if we had a zero length mmio eventfd assigned on
KVM_MMIO_BUS. It will never be found by kvm_io_bus_cmp() since it
always compares the kvm_io_range() with the length that guest
wrote. This will cause e.g for vhost, kick will be trapped by qemu
userspace instead of vhost. Fixing this by using zero length if an
iodevice is zero length.

Cc: stable@vger.kernel.org
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-15 16:59:46 +02:00
Jason Wang eefd6b06b1 kvm: fix double free for fast mmio eventfd
We register wildcard mmio eventfd on two buses, once for KVM_MMIO_BUS
and once on KVM_FAST_MMIO_BUS but with a single iodev
instance. This will lead to an issue: kvm_io_bus_destroy() knows
nothing about the devices on two buses pointing to a single dev. Which
will lead to double free[1] during exit. Fix this by allocating two
instances of iodevs then registering one on KVM_MMIO_BUS and another
on KVM_FAST_MMIO_BUS.

CPU: 1 PID: 2894 Comm: qemu-system-x86 Not tainted 3.19.0-26-generic #28-Ubuntu
Hardware name: LENOVO 2356BG6/2356BG6, BIOS G7ET96WW (2.56 ) 09/12/2013
task: ffff88009ae0c4b0 ti: ffff88020e7f0000 task.ti: ffff88020e7f0000
RIP: 0010:[<ffffffffc07e25d8>]  [<ffffffffc07e25d8>] ioeventfd_release+0x28/0x60 [kvm]
RSP: 0018:ffff88020e7f3bc8  EFLAGS: 00010292
RAX: dead000000200200 RBX: ffff8801ec19c900 RCX: 000000018200016d
RDX: ffff8801ec19cf80 RSI: ffffea0008bf1d40 RDI: ffff8801ec19c900
RBP: ffff88020e7f3bd8 R08: 000000002fc75a01 R09: 000000018200016d
R10: ffffffffc07df6ae R11: ffff88022fc75a98 R12: ffff88021e7cc000
R13: ffff88021e7cca48 R14: ffff88021e7cca50 R15: ffff8801ec19c880
FS:  00007fc1ee3e6700(0000) GS:ffff88023e240000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8f389d8000 CR3: 000000023dc13000 CR4: 00000000001427e0
Stack:
ffff88021e7cc000 0000000000000000 ffff88020e7f3be8 ffffffffc07e2622
ffff88020e7f3c38 ffffffffc07df69a ffff880232524160 ffff88020e792d80
 0000000000000000 ffff880219b78c00 0000000000000008 ffff8802321686a8
Call Trace:
[<ffffffffc07e2622>] ioeventfd_destructor+0x12/0x20 [kvm]
[<ffffffffc07df69a>] kvm_put_kvm+0xca/0x210 [kvm]
[<ffffffffc07df818>] kvm_vcpu_release+0x18/0x20 [kvm]
[<ffffffff811f69f7>] __fput+0xe7/0x250
[<ffffffff811f6bae>] ____fput+0xe/0x10
[<ffffffff81093f04>] task_work_run+0xd4/0xf0
[<ffffffff81079358>] do_exit+0x368/0xa50
[<ffffffff81082c8f>] ? recalc_sigpending+0x1f/0x60
[<ffffffff81079ad5>] do_group_exit+0x45/0xb0
[<ffffffff81085c71>] get_signal+0x291/0x750
[<ffffffff810144d8>] do_signal+0x28/0xab0
[<ffffffff810f3a3b>] ? do_futex+0xdb/0x5d0
[<ffffffff810b7028>] ? __wake_up_locked_key+0x18/0x20
[<ffffffff810f3fa6>] ? SyS_futex+0x76/0x170
[<ffffffff81014fc9>] do_notify_resume+0x69/0xb0
[<ffffffff817cb9af>] int_signal+0x12/0x17
Code: 5d c3 90 0f 1f 44 00 00 55 48 89 e5 53 48 89 fb 48 83 ec 08 48 8b 7f 20 e8 06 d6 a5 c0 48 8b 43 08 48 8b 13 48 89 df 48 89 42 08 <48> 89 10 48 b8 00 01 10 00 00
 RIP  [<ffffffffc07e25d8>] ioeventfd_release+0x28/0x60 [kvm]
 RSP <ffff88020e7f3bc8>

Cc: stable@vger.kernel.org
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-15 16:59:31 +02:00
Jason Wang 85da11ca58 kvm: factor out core eventfd assign/deassign logic
This patch factors out core eventfd assign/deassign logic and leaves
the argument checking and bus index selection to callers.

Cc: stable@vger.kernel.org
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-15 16:58:47 +02:00
Jason Wang 8453fecbec kvm: don't try to register to KVM_FAST_MMIO_BUS for non mmio eventfd
We only want zero length mmio eventfd to be registered on
KVM_FAST_MMIO_BUS. So check this explicitly when arg->len is zero to
make sure this.

Cc: stable@vger.kernel.org
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-15 16:58:27 +02:00
Wei Yang 81523aac01 KVM: make the declaration of functions within 80 characters
After 'commit 0b8ba4a2b6 ("KVM: fix checkpatch.pl errors in
kvm/coalesced_mmio.h")', the declaration of the two function will exceed 80
characters.

This patch reduces the TAPs to make each line in 80 characters.

Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-14 18:43:19 +02:00
Paolo Bonzini 51256484c0 KVM/ARM changes for 4.3-rc2
- Fix timer interrupt injection after the rework
   that went in during the merge window
 - Reset the timer to zero on reboot
 - Make sure the TCR_EL2 RES1 bits are really set to 1
 - Fix a PSCI affinity bug for non-existing vcpus
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJV9VQYAAoJECPQ0LrRPXpDYFsQAIp+nIxv6LijQdq310EF7Z95
 1j16vx9NfsAsNH0pwiRmx4gfNOHlPp6f30Kb1HJf2TN08Rc7TS8j4Dr3zYnZEdQj
 9eNGTjCjlz93VQwKnTBvBvYkHsCEWC76pOxiYoFmnLsGc4m/OilHhohOzOZTAMFC
 Le07VXJwrhGHQ5bjdIMmFj+5rMj4eWfT2bYg8uVl5EUNFNkDgAMtT/Nbml90friC
 x+r2I9H+G8hHmemOv6hefW7l2JScLSYpqLeGdxZUtnGy9LNP3+jTD1QyqUftUPuS
 HtcB4zCtRk62nMupgFNV514Kf26wcwpS53vhd8aM2kxSkpr5xkUFoL+uJNT8ssIH
 Y+FwAOeTD0osWbmxw8Gf9d3qYzPBQSCRP3E4mCbNNNsTlMRU+Hu9au0VNBKggkfF
 fZ4UphCVX2C+cWaQcB40950h1F76Vx3boAfcMgiXoO+8LJx9OogDtr8+j5cBBbKU
 +tMngLhelsMtSCTam9c0jS6BsQfHDy3W1CQNl30cqd2RFjvygOSAqzdCMlBk0lLG
 4Sq0eib1zJM+rE2OQs8SaAftyQ0kbElmM3XZB3ZiitaHgkUKV7kt9dMUG9Vfn2SE
 /ycgR9eoBq5P6FKhyROmL+0g824nYJmn4fwpecw1rHoRr8jyZjvpbE3VSL0aI5XW
 w4UYsAQSTcqM6bHpNYuu
 =G02h
 -----END PGP SIGNATURE-----

Merge tag 'kvm-arm-for-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master

KVM/ARM changes for 4.3-rc2

- Fix timer interrupt injection after the rework
  that went in during the merge window
- Reset the timer to zero on reboot
- Make sure the TCR_EL2 RES1 bits are really set to 1
- Fix a PSCI affinity bug for non-existing vcpus
2015-09-14 17:07:35 +02:00
Wanpeng Li edb9272f35 KVM: fix polling for guest halt continued even if disable it
If there is already some polling ongoing, it's impossible to disable the
polling, since as soon as somebody sets halt_poll_ns to 0, polling will
never stop, as grow and shrink are only handled if halt_poll_ns is != 0.

This patch fix it by reset vcpu->halt_poll_ns in order to stop polling
when polling is disabled.

Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2015-09-14 17:07:04 +02:00