Add SDHI0 and SDHI1 slave ids for RX and TX to enable
DMA Engine support for SDHI on the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Simply add MMCIF slave ids for RX and TX to enable
DMA Engine support for the AG5EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SDHI0 and SDHI1 support to the AG5EVM board
including platform data, pinmux configuration
and clock bindings.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the struct resources for DSI0 to include the
hardware block name. Purely cosmetic, makes /proc/iomem
look slightly better.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a 100 ms delay after the MIPI-DSI panel reset to
fix issue related to the LCD panel not starting properly
at boot up time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current format selection of FSI-codecs depended on platform information for FSI,
and chip default settings for codecs. It is not understandable/formal method.
This patch modify FSI and FSI-codecs to use snd_soc_dai_set_fmt.
But FSI can use I2S/PCM and SPDIF format today.
It can be selected to I2S/PCM by snd_soc_dai_set_fmt, but can not select SPDIF.
So, this patch change FSI platform information to have DAI/SPDIF mode.
If platform selects DAI mode (default),
FSI-codecs can select I2S/PCM by snd_soc_dai_set_fmt,
and if it is SPDIF mode, FSI become SPDIF format.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add snd_soc_dai_ops :: set_fmt to FSI driver and
select master/slave clock mode by snd_soc_dai_set_fmt on
fsi-xxx.c instead of platform infomation code.
This patch remove fsi_is_master function which is no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add platform data for MIPI-DSI and LCDC on the AG5EVM
board. The sh73a0 clkdev bindings are also updated.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break-out GIC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.
Covers sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Follow up to pfc-sh73a0.c's pull-up support.
Change GPIO_FN_KEYINx to GPIO_FN_KEYINx_PU.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add INTCS support for the sh73a0 processor.
The interrupts on the sh73a0 processor are managed
through controllers such as GIC, INTCS and INTCA.
The ARM cores use the GIC as primary interrupt
controller and the INTCS and INTCA are hanging off
the GIC as cascaded interrupt controllers.
Peripherals connected both to the GIC and the INTC
controllers should if possible only use the GIC.
If no GIC connection is available then INTCS and
INTCA may be used instead.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just add port multiplex settings to enable i2c modules.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consists of platform device resources/data for the board, and
simple clvdev entry for MSTP bit for keysc module.
This support only 49 of 80 key-switches on the board.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ag5evm board now uses gpio api to initialize pins and peripherals.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds initial support for Renesas SH-Mobile AG5.
At this point the AG5 CPU support is limited to the ARM
core, SCIF serial and a CMT timer together with L2 cache
and the GIC. The AG5EVM board also supports Ethernet.
Future patches will add support for GPIO, INTCS, CPGA
and platform data / driver updates for devices such as
IIC, LCDC, FSI, KEYSC, CEU and SDHI among others.
The code in entry-macro.S will be cleaned up when the
ARM IRQ demux code improvements have been merged.
Depends on the AG5EVM mach-type recently registered but
not yet present in arch/arm/tools/mach-types.
As the AG5EVM board comes with 512MiB memory it is
recommended to turn on HIGHMEM.
Many thanks to Yoshii-san for initial bring up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm