Commit e9c7469bb4 ("md: implment REQ_FLUSH/FUA support")
introduced R5_WantFUA flag and set rw to WRITE_FUA in that case.
However remaining code still checks whether rw is exactly same
as WRITE or not, so FUAed-write ends up with being treated as
READ. Fix it.
This bug has been present since 2.6.37 and the fix is suitable for any
-stable kernel since then. It is not clear why this has not caused
more problems.
Cc: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The @bio->bi_phys_segments consists of active stripes count in the
lower 16 bits and processed stripes count in the upper 16 bits. So
logical-OR operator should be bitwise one.
This bug has been present since 2.6.27 and the fix is suitable for any
-stable kernel since then. Fortunately the bad code is only used on
error paths and is relatively unlikely to be hit.
Cc: stable@kernel.org
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Drivers using multiple framebuffers got broken by commit
41c2e75e60 which ignored the framebuffer
(or register) map offset when looking for existing maps. The rationale
was that the kernel-userspace ABI is fixed at a 32-bit offset, so the
real offsets could not always be handed over for comparison.
Instead of ignoring the offset we will compare the lower 32 bit. Drivers
using multiple framebuffers should just make sure that the lower 32 bit
are different. The existing drivers in question are practically limited
to 32-bit systems so that should be fine for them.
It is assumed that current drivers always specify a correct framebuffer
map offset, even if this offset was ignored since above commit. So this
patch should not change anything for drivers using only one framebuffer.
Drivers needing multiple framebuffers with 64-bit map offsets will need
to cook up something, for instance keeping an ID in the lower bit which
is to be aligned away when it comes to using the offset.
All of above applies to _DRM_REGISTERS as well.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems to me that we are leaking 'user_pages' in
drivers/gpu/drm/i915/i915_gem.c::i915_gem_shmem_pread_slow() if
read_cache_page_gfp() fails.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To my knowledge, the limit is 16 on r300.
(the docs don't say what the limit is)
The lack of bounds checking can be abused to do all sorts of things
(from bypassing parts of the CS checker to crashing the kernel).
Bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36745
Cc: stable@kernel.org
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Apple uses the same subsystem pci ids for lots of
hardware much of which is wired up differently. In
this case, the G5 imac and the G5 tower.
Only apply the quirk configuration to G5 towers.
Reported-by: Joachim Henke <j-o@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Joachim Henke <j-o@users.sourceforge.net>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When I added 3448a19da4
I forgot about the special uv handling code for this, so this
patch fixes it up.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ingo Molnar
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an obsolete Alpha adjustment in the drm for MGA on Alpha.
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an obsolete Alpha adjustment, and modify another,
to go with the current Alpha architecture support.
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
the code always returns ret regardless, so if(ret) check is unnecessary.
v2: fixed up the spelling.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Reviewed-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
WARNING: vmlinux.o(.devinit.text+0x253e): Section mismatch in reference from the function hplance_init_one() to the function .init.text:hplance_init()
The forward declaration had the correct attribute, but the actual function
definition hadn't.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
Fix broken IRQ autoprobing in 3c503 driver:
- improper IRQ freeing (does not free IRQs causes WARN)
- missing break when an working IRQ is found
The driver works with this patch.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
Return error on out of range cpsdvsr value.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since the inclusion of eGalax devices in 2.6.39, I've got some
bug reports for 480d and other devices.
The problem lies in the reports descriptors: eGalax supports both
pen and fingers, and so the reports descriptors contained both.
But hid-multitouch relies on them to detect the last item in each
field to send the multitouch events. In 480d, the last item is not
Y as it should but Pressure. That means that the fields are not
aligned and X,Y are at 0,0 (the other touch coordinates of the report).
With this patch, the detection is made only when the field ContactID
has been detected inside the collection.
There is still a problem with the detections of the range as stylus
and fingers may not have the same min/max, but it's a start.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
cpufreq_stats leaves behind its sysfs entries, which causes a panic
when something stumbled across them.
(Discovered by unloading cpufreq_stats while powertop was loaded).
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: stable@kernel.org
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio/basic_mmio: add missing include of spinlock_types.h
gpio/nomadik: fix sleepmode for elder Nomadik
We leak the memory allocated to 'phi' when the variable goes out of scope
in hfcsusb_ph_info().
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King said:
>
> So, to summarize what its doing:
>
> 1. It allocates buffers for rx and tx.
> 2. It maps them with dma_map_single().
> This transfers ownership of the buffer to the DMA device.
> 3. In ep93xx_xmit,
> 3a. It copies the data into the buffer with skb_copy_and_csum_dev()
> This violates the DMA buffer ownership rules - the CPU should
> not be writing to this buffer while it is (in principle) owned
> by the DMA device.
> 3b. It then calls dma_sync_single_for_cpu() for the buffer.
> This transfers ownership of the buffer to the CPU, which surely
> is the wrong direction.
> 4. In ep93xx_rx,
> 4a. It calls dma_sync_single_for_cpu() for the buffer.
> This at least transfers the DMA buffer ownership to the CPU
> before the CPU reads the buffer
> 4b. It then uses skb_copy_to_linear_data() to copy the data out.
> At no point does it transfer ownership back to the DMA device.
> 5. When the driver is removed, it dma_unmap_single()'s the buffer.
> This transfers ownership of the buffer to the CPU.
> 6. It frees the buffer.
>
> While it may work on ep93xx, it's not respecting the DMA API rules,
> and with DMA debugging enabled it will probably encounter quite a few
> warnings.
This patch fixes these violations.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a197b59ae6 (mm: fail GFP_DMA allocations when ZONE_DMA is not
configured) made page allocator to return NULL if GFP_DMA is set but
CONFIG_ZONE_DMA is disabled.
This causes ep93xx_eth to fail:
WARNING: at mm/page_alloc.c:2251 __alloc_pages_nodemask+0x11c/0x638()
Modules linked in:
[<c0035498>] (unwind_backtrace+0x0/0xf4) from [<c0043da4>] (warn_slowpath_common+0x48/0x60)
[<c0043da4>] (warn_slowpath_common+0x48/0x60) from [<c0043dd8>] (warn_slowpath_null+0x1c/0x24)
[<c0043dd8>] (warn_slowpath_null+0x1c/0x24) from [<c0083b6c>] (__alloc_pages_nodemask+0x11c/0x638)
[<c0083b6c>] (__alloc_pages_nodemask+0x11c/0x638) from [<c00366fc>] (__dma_alloc+0x8c/0x3ec)
[<c00366fc>] (__dma_alloc+0x8c/0x3ec) from [<c0036adc>] (dma_alloc_coherent+0x54/0x60)
[<c0036adc>] (dma_alloc_coherent+0x54/0x60) from [<c0227808>] (ep93xx_open+0x20/0x864)
[<c0227808>] (ep93xx_open+0x20/0x864) from [<c0283144>] (__dev_open+0xb8/0x108)
[<c0283144>] (__dev_open+0xb8/0x108) from [<c0280528>] (__dev_change_flags+0x70/0x128)
[<c0280528>] (__dev_change_flags+0x70/0x128) from [<c0283054>] (dev_change_flags+0x10/0x48)
[<c0283054>] (dev_change_flags+0x10/0x48) from [<c001a720>] (ip_auto_config+0x190/0xf68)
[<c001a720>] (ip_auto_config+0x190/0xf68) from [<c00233b0>] (do_one_initcall+0x34/0x18c)
[<c00233b0>] (do_one_initcall+0x34/0x18c) from [<c0008400>] (kernel_init+0x94/0x134)
[<c0008400>] (kernel_init+0x94/0x134) from [<c0030858>] (kernel_thread_exit+0x0/0x8)
Since there is no restrictions for DMA on ep93xx, we can fix this by just
removing the GFP_DMA flag from the call.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use simply kmalloc() to allocate the buffers. This also simplifies the
code and allows us to perform DMA sync operations more easily.
Memory is allocated with only GFP_KERNEL since there are no DMA allocation
restrictions on this platform.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't use NULL for any DMA API functions, unless we are dealing with
ISA or EISA device. So pass correct struct dev pointer to these functions.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
/tmp/ccvoZ6h8.s: Assembler messages:
/tmp/ccvoZ6h8.s:284: Warning: register range not in ascending order
/tmp/ccvoZ6h8.s:881: Warning: register range not in ascending order
/tmp/ccvoZ6h8.s:1087: Warning: register range not in ascending order
by ensuring that we have temporary variables placed into specific
registers. Reorder the code a bit to allow the resulting assembly
to be slightly more optimal.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were clearing out the multicast filter whenever the interface was
upped, and not setting the mode bits correctly. This can cause
problems if there are any multicast addresses already set at this
point, or if ALLMULTI was set.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this the compiler can (and does) optimize register reads away
from within loops, and other such optimizations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the legit warnings 'make W=3 drivers/ide/ide-cd.c'
generates is:
drivers/ide/ide-cd.c: In function ide_cd_do_request
drivers/ide/ide-cd.c:828:2: warning: conversion to int from \
unsigned int may change the sign of the result
drivers/ide/ide-cd.c:833:2: warning: conversion to int from \
unsigned int may change the sign of the result
nsectors is declared int, should be unsigned int.
blk_rq_sectors() returns unsigned int, and ide_complete_rq
expects unsigned int as well. Fixes both warnings.
Signed-off-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32, leon: bugfix in LEON SMP interrupt init
sparc32, sun4m: bugfix in SMP IPI traphandler
sparc: Remove unnecessary semicolons
Add support for allocating irqs for bootbus devices
Do not skip interrupt sources in sun4d interrupt handler and acknowledge interrupts correctly
Restructure sun4d_build_device_irq so that timer interrupts can be allocated
sparc: PCIC_PCI needs SPARC32 dependency
sparc: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
sparc32,leon: add GRPCI2 PCI Host driver
sparc32,leon: added LEON-common low-level PCI routines
sparc32: added CONFIG_PCIC_PCI Kconfig setting
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: iio: max517: Fix iio_info changes
Staging: mei: fix debug code
Staging: cx23885: fix include of altera.h
staging: iio: error case memory leak fix
staging: ath6kl: Fix a kernel panic during suspend/resume
staging: gma500: get control from firmware framebuffer if conflicts
staging: gma500: Skip bogus LVDS VBT mode and check for LVDS before adding backlight
staging: usbip: bugfix prevent driver unbind
staging: iio: industrialio-trigger: set iio_poll_func private_data
staging: rts_pstor: use bitwise operator instead of logical one
staging: fix ath6kl build when CFG80211 is not enabled
staging: brcm80211: fix for 'multiple definition of wl_msg_level' build err
staging: fix olpc_dcon build, needs BACKLIGHT_CLASS_DEVICE
Staging: remove STAGING_EXCLUDE_BUILD option
Staging: altera: move .h file to proper place
* 'stable/xen-swiotlb.bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb-2.6:
swiotlb: Export swioltb_nr_tbl and utilize it as appropiate.
struct iio_info introduced a bug where the second channel of a MAX518 can't be
used. This commit fixes the typo (using max518 instead of the max517 struct).
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has higher precedence than !=. H_RDY is 8 and since neither 0 nor
1 are equal to 8 the original condition was always true.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
int i is only needed if CONFIG_ACPI is set
so move it within a new ifdef so kernels without ACPI
don't allocate space for nothing. Fixes warning too.
Signed-off-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
[v2: Fixed warning when CONFIG_ACPI was defined]
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
The patch moves rtc driver for PKUnity-v3 SoC from arch/unicore32/kernel/
to drivers/rtc/, with renaming it to rtc-puv3.c.
Also, Kconfig, Makefile, and MAINTAINERS are modified correspondingly.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Each eTSEC device should own localized filer table.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves enabling channel for window, because there should
be enabling channel before enabling window. If the sequence is
reversed, it makes the problem in displaying images to lcd panel.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes mishandling in virtual resolution checking.
Previously, virtual resolution is changed to virtual_x and virtual_y
which mean the size for buffer allocation, when s3c_fb_check_var is
called by fb_check_var. However, it is meaningless, since virtual_x
and virtual_y are fixed and user cannot change virtual resolution.
Therefore, virtual resolution should be more than resolution
such as xres and yres.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debug statement for GUI idle interrupt is wrong and incorrectly
reports CP EOP interrupt; trivial issue, but confusing for
someone trying to distinguish interrupt sources while debugging
... fixed
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Filter out modes that are higher than the max pixel
clock.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DRM_IOCTL_MODE_GETRESOURCES ioctl just returns bogus framebuffers.
That is because the framebuffers for each file are in the filp_head
member of struct drm_framebuffer, not in the head member.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Get rid of ->syncchunk and ->counter_bits since they're never used.
Also discard COUNTER_BYTE_RATIO which is unused.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add check to determine if a device needs full resync or if partial resync will do
RAID 5 was assuming that if a device was not In_sync, it must undergo a full
resync. We add a check to see if 'saved_raid_disk' is the same as 'raid_disk'.
If it is, we can safely skip the full resync and rely on the bitmap for
partial recovery instead. This is the legitimate purpose of 'saved_raid_disk',
from md.h:
int saved_raid_disk; /* role that device used to have in the
* array and could again if we did a partial
* resync from the bitmap
*/
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add bitmap support to the device-mapper specific metadata area.
This patch allows the creation of the bitmap metadata area upon
initial array creation via device-mapper.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
MAINTAINERS: add a maintainer to Gadget Framework
USB: serial: add another 4N-GALAXY.DE PID to ftdi_sio driver
Revert "USB: option: add ID for ZTE MF 330"
drivers/usb/host/ohci-pxa27x.c: add missing clk_put
USB: CONFIG_USB_GADGET_DUALSPEED is not user-configurable
USB: dummy-hcd needs the has_tt flag
usb-storage: redo incorrect reads
usb/renesas_usbhs: free uep on removal
usb/s3c-hsudc: fix error path
usb/pxa25x_udc: cleanup the LUBBOCK err path
usb/mv_udc_core: fix compile
usb: gadget: include <linux/prefetch.h> to fix compiling error
USB: s3c-hsotg: Tone down debugging
usb: remove bad dput after dentry_unhash
USB: core: Tolerate protocol stall during hub and port status read
musb: fix prefetch build failure
USB: cdc-acm: Adding second ACM channel support for Nokia E7 and C7
usb-gadget: unlock data->lock mutex on error path in ep_write()
USB: option Add blacklist for ZTE K3765-Z (19d2:2002)
option: add Prolink PH300 modem IDs
...
One new offender detected by the recently increased type checking in
platform_get_drvdata():
drivers/rtc/rtc-m41t93.c: In function ‘m41t93_remove’:
drivers/rtc/rtc-m41t93.c:192: warning: passing argument 1 of ‘platform_get_drvdata’ from incompatible pointer type
Use spi_get_drvdata() instead of platform_get_drvdata(), cfr. commit
42fea15d6d ("spi/rtc-{ds1390,ds3234,m41t94}:
Use spi_get_drvdata() for SPI devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: off by one errors in multicalls.c
xen: use the trigger info we already have to choose the irq handler
We use priv->mutex to avoid race conditions between chswitch_done()
and mac_channel_switch(), when marking channel switch in
progress. But chswitch_done() can be called in atomic context
from rx_csa() or with mutex already taken from commit_rxon().
To fix remove mutex from chswitch_done() and use atomic bitops
for marking channel switch pending.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During channge channel, tx power will not send to uCode, the tx power command
should send after scan complete. but should also can send after RXON command.
Stable fix identified by Stanislaw Gruszka <sgruszka@redhat.com>.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cx23885 driver was including staging/altera.h, but that file has
moved back into the driver directory.
Why a non-staging driver was including a staging driver is beyond me,
but this fixes the build so everything is happy for now.
For the record, it's not ok for a non-staging driver to depend on a
staging one, as that implies that the non-staging one should also be in
the staging tree if that's needed.
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] soc_camera: preserve const attribute
[media] uvc_entity: initialize return value
[media] media: Fix media device minor registration
[media] Make nchg variable signed because the code compares this variable against negative values
[media] omap3isp: fix compiler warning
[media] v4l: Fix media_entity_to_video_device macro argument name
[media] ivtv: Internally separate encoder & decoder standard setting
[media] ivtvfb: Add sanity check to ivtvfb_pan_display()
[media] ivtvfb: use display information in info not in var for panning
[media] ivtv: Make two ivtv_msleep_timeout calls uninterruptable
[media] anysee: return EOPNOTSUPP for unsupported I2C messages
[media] gspca - ov519: Set the default frame rate to 15 fps
[media] gspca - stv06xx: Set a lower default value of gain for hdcs sensors
[media] gspca: Remove coarse_expo_autogain.h
[media] gspca - ov519: Change the ovfx2 bulk transfer size
[media] gspca - ov519: Fix a regression for ovfx2 webcams
* 'drm-radeon-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: disable hdmi audio by default
drm/radeon/kms: fix for radeon on systems >4GB without hardware iommu
drm/radeon/kms: set family for use in parser.
The flush_to_ldisc() work entry has special logic to notice when it has
seen the original tail of the data queue, and it avoids continuing the
flush if it sees that _original_ tail rather than the current tail.
This logic can trigger in case somebody is constantly adding new data to
the tty while the flushing is active - and the intent is to avoid
excessive CPU usage while flushing the tty, especially as we used to do
this from a softirq context which made it non-preemptible.
However, since we no longer re-arm the work-queue from within itself
(because that causes other trouble: see commit a5660b41af "tty: fix
endless work loop when the buffer fills up"), this just leads to
possible hung tty's (most easily seen in SMP and with a test-program
that floods a pty with data - nobody seems to have reported this for any
real-life situation yet).
And since the workqueue isn't done from timers and softirq's any more,
it's doubtful whether the CPU useage issue is really relevant any more.
So just remove the logic entirely, and see if anybody ever notices.
Alternatively, we might want to re-introduce the "re-arm the work" for
just this case, but then we'd have to re-introduce the delayed work
model or some explicit timer, which really doesn't seem worth it for
this.
Reported-and-tested-by: Guillaume Chazarain <guichaz@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On my x86_64 system with >4GB of ram and swiotlb instead of
a hardware iommu (because I have a VIA chipset), the call
to pci_set_dma_mask (see below) with 40bits returns an error.
But it seems that the radeon driver is designed to have
need_dma32 = true exactly if pci_set_dma_mask is called
with 32 bits and false if it is called with 40 bits.
I have read somewhere that the default are 32 bits. So if the
call fails I suppose that need_dma32 should be set to true.
And indeed the patch fixes the problem I have had before
and which I had described here:
http://choon.net/forum/read.php?21,106131,115940
Acked-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Wierdly the kms parser never initialised the family, it wasn't really used
much, but the fmt checker patch started using it and it fell over.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the 'sync_super' function pointer to MD array structure (struct mddev_s)
If device-mapper (dm-raid.c) is to define its own on-disk superblock and be
able to load it, there must still be a way for MD to initiate superblock
updates. The simplest way to make this happen is to provide a pointer in
the MD array structure that can be set by device-mapper (or other module)
with a function to do this. If the function has been set, it will be used;
otherwise, the method with be looked up via 'super_types' as usual.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1: Changes to allow RAID1 to be used by device-mapper (dm-raid.c)
Added the necessary congestion function and conditionalize calls requiring an
array 'queue' or 'gendisk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Move personality and sync/recovery thread starting outside md_run.
Moving the wakeup's of the personality and sync/recovery threads out of
md_run and into do_md_run and mddev_resume solves two issues:
1) It allows bitmap_load to be called before the sync_thread is run and
2) when MD personalities are used by device-mapper (dm-raid.c), the start-up
of the array is better alligned with device-mapper primatives
(CTR/resume/suspend/DTR). I/O - in this case, recovery operations - should
not happen until after a resume has taken place.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Make message a bit clearer by s/blocks/k/
I chose 'k' vs 'kiB' or 'kB' because it is what is used earlier in the
message. 'k' may be a bit ambigous, but I think it's better than "blocks"
which normally means 512, but means 1024 in MD.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Disallow resync I/O while the RAID array is suspended.
Recovery, resync, and metadata I/O should not be allowed while a device is
suspended.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Don't attempt md_integrity_register if there is no gendisk struct available.
When MD arrays are built via device-mapper, the gendisk structure is not
available via mddev.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv40: fall back to paged dma object for the moment
drm/nouveau: fix leak of gart mm node
drm/nouveau: fix vram page mapping when crossing page table boundaries
drm/nv17-nv40: Fix modesetting failure when pitch == 4096px (fdo bug 35901).
drm/nouveau: don't create accel engine objects when noaccel=1
drm/nvc0: recognise 0xdX chipsets as NV_C0
drm/i915: Add a no lvds quirk for the Asus EeeBox PC EB1007
drm/i915: Share the common force-audio property between connectors
drm/i915: Remove unused enum "chip_family"
drm/915: fix relaxed tiling on gen2: tile height
drm/i915/crt: Explicitly return false if connected to a digital monitor
drm/i915: Replace ironlake_compute_wm0 with g4x_compute_wm0
drm/i915: Only print out the actual number of fences for i915_error_state
drm/i915: s/addr & ~PAGE_MASK/offset_in_page(addr)/
drm: i915: correct return status in intel_hdmi_mode_valid()
drm/i915: fix regression after clock gating init split
drm/i915: fix if statement in ivybridge irq handler
* 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/atom: fix PHY init
drm/radeon/kms: add missing Evergreen texture formats to the CS parser
drm/radeon/kms: viewport height has to be even
drm/radeon/kms: remove duplicate reg from r600 safe regs
drm/radeon/kms: add support for Llano Fusion APUs
drm/radeon/kms: add llano pci ids
drm/radeon/kms: fill in asic struct for llano
drm/radeon/kms: add family ids for llano APUs
drm/radeon: fix oops in ttm reserve when pageflipping (v2)
drm/radeon/kms: clean up the radeon kms Kconfig
drm/radeon/kms: fix thermal sensor reading on juniper
drm/radeon/kms: add missing case for cayman thermal sensor
drm/radeon/kms: add blit support for cayman (v2)
drm/radeon/kms/blit: workaround some hw issues on evergreen+
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (21 commits)
ARM: OMAP4: MMC: increase delay for pbias
arm: omap2plus: move NAND_BLOCK_SIZE out of boards
omap4: hwmod: Enable the keypad
omap3: Free Beagle rev gpios when they are read, so others can read them later
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
omap: rx51: Don't power up speaker amplifier at bootup
omap: rx51: Set regulator V28_A always on
ARM: OMAP4: MMC: no regulator off during probe for eMMC
arm: omap2plus: fix ads7846 pendown gpio request
ARM: OMAP2: Add missing iounmap in omap4430_phy_init
ARM: omap4: Pass core and wakeup mux tables to omap4_mux_init
ARM: omap2+: mux: Allow board mux settings to be NULL
OMAP4: fix return value of omap4_l3_init
OMAP: iovmm: fix SW flags passed by user
arch/arm/mach-omap1/dma.c: Invert calls to platform_device_put and platform_device_del
OMAP2+: mux: fix compilation warnings
OMAP: SRAM: Fix warning: format '%08lx' expects type 'long unsigned int'
arm: omap3: cm-t3517: fix section mismatch warning
OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
ARM: OMAP2: Add missing include of linux/gpio.h
...
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
vfs: make unlink() and rmdir() return ENOENT in preference to EROFS
lmLogOpen() broken failure exit
usb: remove bad dput after dentry_unhash
more conservative S_NOSEC handling
This reverts commit a559d2c8c1.
Turns out that device id 0x1d6b:0x0002 is a USB hub, which causes havoc
when the option driver tries to bind to it.
So revert this as it doesn't seem to be needed at all.
Thanks to Michael Tokarev and Paweł Drobek for working on resolving this
issue.
Cc: Paweł Drobek <pawel.drobek@gmail.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The loops over connection ID strings in pm_runtime_clk_notify()
should actually iterate over the strings and not over the elements
of the first of them, so make them behave as appropriate.
This fixes a regression introduced by commit 600b776eb3
(OMAP1 / PM: Use generic clock manipulation routines for runtime PM).
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When SR-IOV is enabled, i350 devices fail to pass traffic. This is due to
the driver attempting to enable RSS on the PF device, which is not
supported by the i350.
When max_vfs is specified on an i350 adapter, set the number of RSS queues
to 1.
This issue affects 2.6.39 as well.
CC: stable@kernel.org
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
To work around controllers which can't properly plug events while
reset, ata_eh_reset() clears error states and ATA_PFLAG_EH_PENDING
after reset but before RESET is marked done. As reset is the final
recovery action and full verification of devices including onlineness
and classfication match is done afterwards, this shouldn't lead to
lost devices or missed hotplug events.
Unfortunately, it forgot to thaw the port when clearing EH_PENDING, so
if the condition happens after resetting an empty port, the port could
be left frozen and EH will end without thawing it, making the port
unresponsive to further hotplug events.
Thaw if the port is frozen after clearing EH_PENDING. This problem is
reported by Bruce Stenning in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1123265
stable: I think we should weather this patch a bit longer in -rcX
before sending it to -stable. Please wait at least a month
after this patch makes upstream. Thanks.
-v2: Fixed spelling in the comment per Dave Howorth.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Bruce Stenning <b.stenning@indigovision.com>
Cc: stable@kernel.org
Cc: Dave Howorth <dhoworth@mrc-lmb.cam.ac.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If CONFIG_PM is not set, init_iommu_pm_ops() introduced by commit
134fac3f45 (PCI / Intel IOMMU: Use
syscore_ops instead of sysdev class and sysdev) is not defined
appropriately. Fix this issue.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The data pointer should be freed in the error
cases of adis16400_trigger_handler().
Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many Linux distributions would enable vesafb in order to display
early stage boot splash. In this case, we will get garbled X
Window screen if running X fbdev on psbfb.
This is because fb0 is occupied by vesafb while psbfb is on fb1.
They tried to drive the same pieces of hardware at the same
time. With unmodified X start-up, it would try to use default
fb0 framebuffer device and unfortunately it is now broken
becaues fb1 supersedes it.
We should let psbfb takeover framebuffer control from vesafb
to get around this problem.
See also commit : 4410f39109
Signed-off-by: Michael Chang <mchang@novell.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the Fit-PC2 the VBT reports an invalid fixed panel mode for LVDS, this gets
in the way for SDVO. This patch makes VBT parsing skip the invalid mode. When
there is no LVDS output the backlight support crashes so the patch also checks
for this before enabling it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implemented pre_reset and post_reset methods of the driver to prevent the
driver from being unbound upon a device reset. Because of this also the
asynchronous reset introduced to prevent a race condition is no longer necessary
(and sometimes causes problems, because it comes later then expected).
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: usbip-devel <usbip-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Failure to set iio_poll_func private_data, causes zero pointer access
violations in all consumer trigger handlers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like a typo.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build errors when CONFIG_CFG80211 is not enabled:
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b71): undefined reference to `cfg80211_scan_done'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b86): undefined reference to `wiphy_unregister'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b8d): undefined reference to `wiphy_free'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18add7): undefined reference to `wiphy_new'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18ae48): undefined reference to `wiphy_register'
drivers/built-in.o: In function `ar6k_cfg80211_tkip_micerr_event':
(.text+0x18ae95): undefined reference to `cfg80211_michael_mic_failure'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afb5): undefined reference to `__ieee80211_get_channel'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afd2): undefined reference to `cfg80211_inform_bss_frame'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b046): undefined reference to `cfg80211_ibss_joined'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b176): undefined reference to `cfg80211_connect_result'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b190): undefined reference to `cfg80211_disconnected'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b291): undefined reference to `cfg80211_get_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b457): undefined reference to `cfg80211_put_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b4fa): undefined reference to `cfg80211_roamed'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix olpc_dcon.c build by selecting the needed kconfig symbol
BACKLIGHT_CLASS_DEVICE.
olpc_dcon.c:(.text+0x11588b): undefined reference to `backlight_device_register'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Part of the requirement to be in the staging tree is that the code must
build, so let's make it easier for people to build the code to
test/prove this out.
Based on a recommendation from Linus to implement this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Staging drivers should be self-contained, without files in the include/
directories. So move the altera.h file back to the driver directory for
now, until it moves out of the staging tree.
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the case we fail to allocate a new skb, the old skb should
be resubmitted unmodified.
Fixes bug introduced in a9e1286975.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should pass along packet if there's no CRC and no hardware error.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a label before the call to clk_put and jump to that in the error
handling code that occurs after the call to clk_get has succeeded.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1468) changes the Kconfig definition for
USB_GADGET_DUALSPEED. This option is determined entirely by which
device controller drivers are to be built, through Select statements;
it does not need to be (and should not be) configurable by the user.
Also, the "default n" line is superfluous -- everything defaults to N.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like with other host controllers capable of operating at both high
speed and full speed, we need to indicate that the emulated controller
presented by dummy-hcd has this ability. Otherwise usbcore will not
accept full-speed gadgets under dummy-hcd. This patch (as1469) sets
the appropriate has_tt flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB mass-storage devices have bugs that cause them not to handle
the first READ(10) command they receive correctly. The Corsair
Padlock v2 returns completely bogus data for its first read (possibly
it returns the data in encrypted form even though the device is
supposed to be unlocked). The Feiya SD/SDHC card reader fails to
complete the first READ(10) command after it is plugged in or after a
new card is inserted, returning a status code that indicates it thinks
the command was invalid, which prevents the kernel from retrying the
read.
Since the first read of a new device or a new medium is for the
partition sector, the kernel is unable to retrieve the device's
partition table. Users have to manually issue an "hdparm -z" or
"blockdev --rereadpt" command before they can access the device.
This patch (as1470) works around the problem. It adds a new quirk
flag, US_FL_INVALID_READ10, indicating that the first READ(10) should
always be retried immediately, as should any failing READ(10) commands
(provided the preceding READ(10) command succeeded, to avoid getting
stuck in a loop). The patch also adds appropriate unusual_devs
entries containing the new flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sven Geggus <sven-usbst@geggus.net>
Tested-by: Paul Hartman <paul.hartman+linux@gmail.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'nouveau/drm-nouveau-fixes' of /ssd/git/drm-nouveau-next:
drm/nv40: fall back to paged dma object for the moment
drm/nouveau: fix leak of gart mm node
drm/nouveau: fix vram page mapping when crossing page table boundaries
drm/nv17-nv40: Fix modesetting failure when pitch == 4096px (fdo bug 35901).
drm/nouveau: don't create accel engine objects when noaccel=1
drm/nvc0: recognise 0xdX chipsets as NV_C0
* 'keithp/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915: Add a no lvds quirk for the Asus EeeBox PC EB1007
drm/i915: Share the common force-audio property between connectors
drm/i915: Remove unused enum "chip_family"
drm/915: fix relaxed tiling on gen2: tile height
drm/i915/crt: Explicitly return false if connected to a digital monitor
drm/i915: Replace ironlake_compute_wm0 with g4x_compute_wm0
drm/i915: Only print out the actual number of fences for i915_error_state
drm/i915: s/addr & ~PAGE_MASK/offset_in_page(addr)/
drm: i915: correct return status in intel_hdmi_mode_valid()
drm/i915: fix regression after clock gating init split
drm/i915: fix if statement in ivybridge irq handler
Can't find evidence that this is actually done.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I doubt the clock is optional. In case it is it should not return with
an error code because we leak everything.
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is more backwords than it has to be.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|drivers/usb/gadget/mv_udc_core.c:2108: error: label `error' used but not defined
This seems to be broken since the initial commit. I changed this to a
simple return. The other user is the probe code which lets ->probe()
fail on error here.
|drivers/usb/gadget/mv_udc_core.c:2107: warning: passing argument 1 of `dev_err' from incompatible pointer type
|drivers/usb/gadget/mv_udc_core.c:2118: warning: initialization from incompatible pointer type
|drivers/usb/gadget/mv_udc_core.c:2119: warning: initialization from incompatible pointer type
|drivers/usb/gadget/mv_udc_core.c:2130: error: initializer element is not constant
|drivers/usb/gadget/mv_udc_core.c:2130: error: (near initialization for `udc_driver.driver.pm')
Cc: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently the s3c-hsotg driver is extremely chatty, producing voluminous
with large register dumps even in default operation. Tone this down so
we're not chatty unless DEBUG is defined.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 64252c75a (vfs: remove dget() from dentry_unhash()) removed the
useless dget from dentry_unhash but didn't fix up this caller in the usb
code. There used to be exactly one dput per dentry_unhash call; now
there are none.
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI(E)GART isn't quite stable it seems, fall back to old method until I get
the time to sort it out properly.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should hopefully get modesetting at least from this, it appears these are
GF119 chipsets. Accel will come eventually, once I order a board.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.
Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Protocol stall should not be fatal while reading port or hub status as it is
transient state. Currently hub EP0 STALL during port status read results in
failed device enumeration. This has been observed with ST-Ericsson (formerly
Philips) USB 2.0 Hub (04cc:1521) after connecting keyboard.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After the prefetch/list.h restructure, drivers need to explicitly include
linux/prefetch.h in order to use the prefetch() function. Otherwise, the
current driver fails to build:
drivers/usb/musb/musb_core.c: In function 'musb_write_fifo':
drivers/usb/musb/musb_core.c:219: error: implicit declaration of function 'prefetch'
make[3]: *** [drivers/usb/musb/musb_core.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the Nokia E7 and C7 to the list of devices in cdc-acm, allowing
the secondary ACM channel on the device to be exposed. Without this patch
the ACM driver won't claim this secondary channel as it's marked as
having a vendor-specific protocol.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ep_write() acquires data->lock mutex in get_ready_ep() and releases it
on all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.
It is similar to commit 00cc7a5 ("usb-gadget: unlock data->lock mutex on error path in ep_read()"),
it was not fixed at that time by accident.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The funtion option_send_status times out when sending USB messages
to the interfaces 0, 1, and 2 of this UMTS stick. This results in a
5s timeout in the function causing other tty operations to feel very
sluggish.
This patch adds a blacklist entry for these 3 interfaces on the ZTE
K3765-Z device.
I was also able to reproduce the problem with v2.6.38 and v2.6.39.
This is very similar to a problem fixed in
commit 7a89e4cb9c
Author: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Date: Wed Mar 9 09:19:48 2011 +0000
USB: serial: option: Apply OPTION_BLACKLIST_SENDSETUP also for ZTE MF626
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This modem really wants sendsetup blacklisted for interfaces 0 and 1,
otherwise the kernel hardlocks for about 10 seconds while waiting for
the modem's firmware to respond, which it of course doesn't do.
A slight complication here is that TCT (who owns the Alcatel brand) used
the same USB IDs for the X200 as the X060s despite the devices having
completely different firmware and AT command sets, so we end up adding
the X060s to the blacklist at the same time. PSA to OEMs: don't use the
same USB IDs for different devices. Really. It makes your kittens cry.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uses Longcheer-based firmware and AT command set.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
USB: xhci - fix interval calculation for FS isoc endpoints
xhci: Disable MSI for some Fresco Logic hosts.
xhci: Do not issue device reset when device is not setup
xhci: Add defines for hardcoded slot states
xhci: Bigendian fix for xhci_check_bandwidth()
xhci: Bigendian fix for skip_isoc_td()
By default the io_tlb_nslabs is set to zero, and gets set to
whatever value is passed in via swiotlb_init_with_tbl function.
The default value passed in is 64MB. However, if the user provides
the 'swiotlb=<nslabs>' the default value is ignored and
the value provided by the user is used... Except when the SWIOTLB
is used under Xen - there the default value of 64MB is used and
the Xen-SWIOTLB has no mechanism to get the 'io_tlb_nslabs' filled
out by setup_io_tlb_npages functions. This patch provides a function
for the Xen-SWIOTLB to call to see if the io_tlb_nslabs is set
and if so use that value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Setting tx power can be deferred during scan or changing channel.
If after that correct tx power settings will not be sent to device,
we can observe transmission problems and timeouts. Force to send
tx power settings also after partial rxon change, to assure device
always be configured with up-to-date settings.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=36492
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid queue and run autowakeup_work when device is not present anymore.
That prevent rmmod and device remove crash introduced by:
commit 1c0bcf89d8
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Sat Apr 30 17:18:18 2011 +0200
rt2x00: Add autowake support for USB hardware
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes 802.11n stability and performance regression we have
since 2.6.35. It boost performance on my 5GHz N-only network from about
5MB/s to 8MB/s. Similar percentage boost can be observed on 2.4 GHz.
These are test results of 5x downloading of approximately 700MB iso
image:
vanilla: 5.27 5.22 4.94 4.47 5.31 ; avr 5.0420 std 0.35110
patched: 8.07 7.95 8.06 7.99 7.96 ; avr 8.0060 std 0.055946
This was achieved with NetworkManager configured to do not perform
periodical scans, by configuring constant BSSID. With periodical scans,
after some time, performance downgrade to unpatched driver level, like
in example below:
patched: 7.40 7.61 4.28 4.37 4.80 avr 5.6920 std 1.6683
However patch still make better here, since similar test on unpatched
driver make link disconnects with below messages after some time:
wlan1: authenticate with 00:23:69:35:d1:3f (try 1)
wlan1: authenticate with 00:23:69:35:d1:3f (try 2)
wlan1: authenticate with 00:23:69:35:d1:3f (try 3)
wlan1: authentication with 00:23:69:35:d1:3f timed out
On 2.6.35 kernel patch helps against connection hangs with messages:
iwlagn 0000:20:00.0: queue 10 stuck 3 time. Fw reload.
iwlagn 0000:20:00.0: On demand firmware reload
iwlagn 0000:20:00.0: Stopping AGG while state not ON or starting
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qdio SBAL entry flag is made-up of four different values that are
independent of one another. Some of the bits are reserved by the
hardware and should not be changed by qdio. Currently all four values
are overwritten since the SBAL entry flag is defined as an u32.
Split the SBAL entry flag into four u8's as defined by the hardware
and don't touch the reserved bits.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Namhyung Kim
Tormod Volden
Jesper Juhl
Marek Olšák
Alex Deucher
Dave Airlie
Jay Estabrook
Greg Dietsche
Geert Uytterhoeven
Ondrej Zary
Linus Torvalds
Virupax Sadashivpetimath
Benjamin Tissoires
Dave Jones
Mika Westerberg
Daniel Hellstrom
Russell King - ARM Linux
Connor Hansen
John W. Linville
David Miller
Russell King
Linus Walleij
Roland Stigge
Dan Carpenter
Guan Xuetao
Ingo Molnar
Wu Jiajun-B06378
Jingoo Han
Ilija Hadzic
Sascha Hauer
马建朋
Jonathan Brassow
Greg Kroah-Hartman
Steffen Sledz
Stanislaw Gruszka
Wey-Yi Guy
Grant Likely
Daniel Haid
Jonathan Brassow
Rafael J. Wysocki
Williams, Mitch A
H Hartley Sweeten
Tejun Heo
Andre Bartke
Vasanthakumar Thiagarajan
Michael Chang
Patrik Jakobsson
Arjan Mels
Michael Hennerich
Nicolas Kaiser
Randy Dunlap
Roland Vossen
Mike McCormack
Thomas Abraham
Julia Lawall
Alan Stern
Austin Zhang
Sebastian Andrzej Siewior
Bryan Wu
Mark Brown
Sage Weil
Ben Skeggs
Francisco Jerez
Colin Cross
Libor Pechacek
Mike Frysinger
Toby Gray
Alexey Khoroshilov
Torsten Hilbrich
Dan Williams
FUJITA Tomonori
Stanislaw Gruszka
Thomas Gleixner
Jan Glauber