The BKL is only used in fill_super, which is protected by the superblocks
s_umount rw_semaphore. Therefore it is safe to remove the BKL entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-usb@vger.kernel.org
This patch (as1429) updates the Kconfig help text for
CONFIG_USB_SUSPEND. The power/level file is now deprecated; we should
tell people to use power/control instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 46034dca51 (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the issue which was observed while transfering
a large file ( > 20MB) over USB (OMAP MUSB controller acts as USB host)
to an attached USB thumb drive.
It was found that CDB field of CBW packet was set to 0x0. This was
due to missing a barrier before DMA engine starts transfer.
This buffer is allocated using dma_alloc_coherent which gives
non-cacheble but bufferable memory and hence needed a write
memory barrier to flush the write buffer.
More info on this thread is here:
http://www.spinics.net/lists/linux-omap/msg33987.html
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space
of request buffer, so fix it.
Also set max_len of cppi dma channel as max size of
int type, so make musb dma handling happier.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Complete the current request only if the data transfer is over.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space of request buffer,
so fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one bugs of OUT transfer in double buffer case:
-the current code only enable autoclear for dma mode 1, and not
for dma mode 0
Without this patch, test #5 of usbtest can't be passed if we
configure musb as g_zero and use fifo mode 3 to enable double
buffer mode.
With this patch and the following patch(fix dma length),
on my beagle B5, test#5(queued bulk out) may go beyond
18Mbyte/s(seems dma mode 0 is quicker in double buffer case)
if musb is configured as g_zero and fifo mode 3 is taken, follows
the test command:
#./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8 [1]
Also I have tested this patch can't make g_ether broken.
[1],source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one infinite hang of bulk IN transfer in double buffer
case, the hang can be observed easily by test #6 of usbtest if musb is
configured as g_zero and fifo mode 3 is taken to enable double fifo.
In fact, the patch only removes the check for non-empty fifo before
loading data from new request into fifo since the check is not correct:
-in double buffer case, fifo may accommodate more than one packet,
even though it has contained one packet already and is non-empty
-since last DMA is completed before calling musb_g_tx, it is sure
that fifo may accommodate at least one packet
Without applying the patch, new requst enqueued from .complte may not
have a chance to be loaded into fifo, then will never be completed and
cause infinite hangs.
With the patch, on my beagle B5, test#6(queued bulk in) can be passed and
test result may go beyond 33Mbyte/s if musb is configured as g_zero and
fifo mode 3 is taken, follows the test command:
#testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8 [1]
[1],
-source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Philip J. Turmel <philip@turmel.org>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Matthias Bayer <jackdachef@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TIOCGICOUNT device ioctl in both mos7720.c and mos7840.c allows
unprivileged users to read uninitialized stack memory, because the
"reserved" member of the serial_icounter_struct struct declared on the
stack is not altered or zeroed before being copied back to the user.
This patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 461c317705eca5cac09a360f488715927fd0a927(into 2.6.36-v3)
is put forward to power down phy if no usb cable is connected,
but does introduce the two issues below:
1), phy is not into work state if usb cable is connected
with PC during poweron, so musb device mode is not usable
in such case, follows the reasons:
-twl4030_phy_resume is not called, so
regulators are not enabled
i2c access are not enabled
usb mode not configurated
2), The kernel warings[1] of regulators 'unbalanced disables'
is caused if poweron without usb cable connected
with PC or b-device.
This patch fixes the two issues above:
-power down phy only if no usb cable is connected with PC
and b-device
-do phy initialization(via __twl4030_phy_resume) if usb cable
is connected with PC(vbus event) or another b-device(ID event) in
twl4030_usb_probe.
This patch also doesn't put VUSB3V1 LDO into active mode in
twl4030_usb_ldo_init until VBUS/ID change detected, so we can
save more power consumption than before.
This patch is verified OK on Beagle board either connected with
usb cable or not when poweron.
[1]. warnings of 'unbalanced disables' of regulators.
[root@OMAP3EVM /]# dmesg
------------[ cut here ]------------
WARNING: at drivers/regulator/core.c:1357 _regulator_disable+0x38/0x128()
unbalanced disables for VUSB1V8
Modules linked in:
Backtrace:
[<c0030c48>] (dump_backtrace+0x0/0x110) from [<c034f5a8>] (dump_stack+0x18/0x1c)
r7:c78179d8 r6:c01ed6b8 r5:c0410822 r4:0000054d
[<c034f590>] (dump_stack+0x0/0x1c) from [<c0057da8>] (warn_slowpath_common+0x54/0x6c)
[<c0057d54>] (warn_slowpath_common+0x0/0x6c) from [<c0057e64>] (warn_slowpath_fmt+0x38/0x40)
r9:00000000 r8:00000000 r7:c78e6608 r6:00000000 r5:fffffffb
r4:c78e6c00
[<c0057e2c>] (warn_slowpath_fmt+0x0/0x40) from [<c01ed6b8>] (_regulator_disable+0x38/0x128)
r3:c0410e53 r2:c0410ad5
[<c01ed680>] (_regulator_disable+0x0/0x128) from [<c01ed87c>] (regulator_disable+0x24/0x38)
r7:c78e6608 r6:00000000 r5:c78e6c40 r4:c78e6c00
[<c01ed858>] (regulator_disable+0x0/0x38) from [<c02382dc>] (twl4030_phy_power+0x15c/0x17c)
r5:c78595c0 r4:00000000
[<c0238180>] (twl4030_phy_power+0x0/0x17c) from [<c023831c>] (twl4030_phy_suspend+0x20/0x2c)
r6:00000000 r5:c78595c0 r4:c78595c0
[<c02382fc>] (twl4030_phy_suspend+0x0/0x2c) from [<c0238638>] (twl4030_usb_irq+0x11c/0x16c)
r5:c78595c0 r4:00000040
[<c023851c>] (twl4030_usb_irq+0x0/0x16c) from [<c034ec18>] (twl4030_usb_probe+0x2c4/0x32c)
r6:00000000 r5:00000000 r4:c78595c0
[<c034e954>] (twl4030_usb_probe+0x0/0x32c) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
r7:00000000 r6:c047d49c r5:c78e6608 r4:c047d49c
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
r7:00000000 r6:c78e6608 r5:c78e6608 r4:c047d49c
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
r6:c78e663c r5:c78e6608 r4:c78e6608
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
r7:00000000 r6:00000002 r5:c78e6608 r4:c78e6600
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c021597c>] (platform_device_add+0x110/0x16c)
[<c021586c>] (platform_device_add+0x0/0x16c) from [<c0220cb0>] (add_numbered_child+0xd8/0x118)
r7:00000000 r6:c045f15c r5:c78e6600 r4:00000000
[<c0220bd8>] (add_numbered_child+0x0/0x118) from [<c001c618>] (twl_probe+0x3a4/0x72c)
[<c001c274>] (twl_probe+0x0/0x72c) from [<c02601ac>] (i2c_device_probe+0x7c/0xa4)
[<c0260130>] (i2c_device_probe+0x0/0xa4) from [<c0214244>] (driver_probe_device+0xd0/0x190)
r5:c7856e20 r4:c047c860
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
r7:c7856e04 r6:c7856e20 r5:c7856e20 r4:c047c860
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
r6:c7856e54 r5:c7856e20 r4:c7856e20
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
r7:c7856e04 r6:c78fd048 r5:c7856e20 r4:c7856e20
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c0211fd8>] (device_register+0x1c/0x20)
[<c0211fbc>] (device_register+0x0/0x20) from [<c0260aa8>] (i2c_new_device+0xec/0x150)
r5:c7856e00 r4:c7856e20
[<c02609bc>] (i2c_new_device+0x0/0x150) from [<c0260dc0>] (i2c_register_adapter+0xa0/0x1c4)
r7:00000000 r6:c78fd078 r5:c78fd048 r4:c781d5c0
[<c0260d20>] (i2c_register_adapter+0x0/0x1c4) from [<c0260f80>] (i2c_add_numbered_adapter+0x9c/0xb4)
r7:00000a28 r6:c04600a8 r5:c78fd048 r4:00000000
[<c0260ee4>] (i2c_add_numbered_adapter+0x0/0xb4) from [<c034efa4>] (omap_i2c_probe+0x324/0x3e8)
r5:00000000 r4:c78fd000
[<c034ec80>] (omap_i2c_probe+0x0/0x3e8) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c021436c>] (__driver_attach+0x68/0x8c)
r7:c78b2140 r6:c047e214 r5:c04600e4 r4:c04600b0
[<c0214304>] (__driver_attach+0x0/0x8c) from [<c021399c>] (bus_for_each_dev+0x50/0x84)
r7:c78b2140 r6:c047e214 r5:c0214304 r4:00000000
[<c021394c>] (bus_for_each_dev+0x0/0x84) from [<c0214068>] (driver_attach+0x20/0x28)
r6:c047e214 r5:c047e214 r4:c00270d0
[<c0214048>] (driver_attach+0x0/0x28) from [<c0213274>] (bus_add_driver+0xa8/0x228)
[<c02131cc>] (bus_add_driver+0x0/0x228) from [<c02146a4>] (driver_register+0xb0/0x13c)
[<c02145f4>] (driver_register+0x0/0x13c) from [<c0215744>] (platform_driver_register+0x4c/0x60)
r9:00000000 r8:c001f688 r7:00000013 r6:c005b6fc r5:c00083dc
r4:c00270d0
[<c02156f8>] (platform_driver_register+0x0/0x60) from [<c001f69c>] (omap_i2c_init_driver+0x14/0x1c)
[<c001f688>] (omap_i2c_init_driver+0x0/0x1c) from [<c002c460>] (do_one_initcall+0xd0/0x1a4)
[<c002c390>] (do_one_initcall+0x0/0x1a4) from [<c0008478>] (kernel_init+0x9c/0x154)
[<c00083dc>] (kernel_init+0x0/0x154) from [<c005b6fc>] (do_exit+0x0/0x688)
r5:c00083dc r4:00000000
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have to do so due to HW limitation.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
seq_files use the private_data field of a file struct for storing a seq_file structure,
data should be stored in seq_file's own private field (e.g. file->private_data->private)
Otherwise seq_release() will free the private data when the file is closed.
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain USB devices, such as the Nokia X6 mobile phone, don't expose any
endpoint descriptors on some of their interfaces. If the ACM driver is forced
to probe all interfaces on a device the a NULL pointer dereference will occur
when the ACM driver attempts to use the endpoint of the alternative settings.
One way to get the ACM driver to probe all the interfaces is by using the
/sys/bus/usb/drivers/cdc_acm/new_id interface.
This patch checks that the endpoint pointer for the current alternate settings
is non-NULL before using it.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm.c : Manage pseudo-modem without AT commands capabilities
Enable to drive electronic simple gadgets based on microcontrolers.
The Interface descriptor is like this:
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0 None
Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The command endpoint is either a bulk or interrupt endpoint, but using
the wrong type of transfer causes an error if CONFIG_USB_DEBUG is
enabled after commit f661c6f8c6, which
checks for this mismatch.
Detect which type of endpoint it is and use a bulk/int URB as
appropriate. There are other function calls specifying a bulk pipe,
but usb_clear_halt doesn't use the pipe type (only the endpoint) and
usb_bulk_msg auto-detects interrupt transfers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P. This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem
with a standard AT-command interface, which is picked up correctly by CDC-ACM.
The second ACM port is marked as having a vendor-specific protocol. This means
that the ACM driver will not claim the second channel by default.
This adds support for the second ACM channel for the following devices:
Nokia E63
Nokia E75
Nokia 6760 Slide
Nokia E52
Nokia E55
Nokia E72
Nokia X6
Nokia N97 Mini
Nokia 5800 Xpressmusic
Nokia E90
Samsung GTi8510 (INNOV8)
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the remove sysfs file, the device configuration is set to -1
(unconfigured). This eventually unbind drivers with the bandwidth_mutex
held. Some drivers may call functions that hold said mutex, like
usb_reset_device. This is the case for rtl8187, for example. This will
lead to the same process holding the mutex twice, which deadlocks.
Besides, according to Alan Stern:
"The deadlock problem probably could be handled somehow, but there's a
separate issue: Until the usb_disable_device call finishes unbinding
the drivers, the drivers are free to continue using their allocated
bandwidth. We musn't change the bandwidth allocations until after the
unbinding is done. So this patch is indeed necessary."
Unbinding the driver before holding the bandwidth_mutex solves the
problem. If any operation after that fails, drivers are not bound again.
But that would be a problem anyway that the user may solve resetting the
device configuration to one that works, just like he would need to do in
most other failure cases.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Pirelli DP-L10 mobile is sold under various brand names. One, already
supported by cp210x, is the T-COM TC300. Here is the lsusb for that version:
-------------------------------------------------------------------
Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe000 T-Com TC 300
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 TC 300
iSerial 3 0001
[snip]
---------------------------------------------------------------------------
However the native Pirelli DP-L10 is not supported:
------------------------------------------------------------------
Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe003 Pirelli DP-L10
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 DP-L10
iSerial 3 0001
[snip]
-------------------------------------------------------------------------
All that is required is an extra USB_DEVICE entry:
{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM
+Mobile */
The patch adds that entry. Tested under 2.6.36-rc2 from git.
Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New device ID added for Balluff RFID reader.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.
Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the following section mismatch warning,
by moving the function rndis_init() from .init.text to .text.
WARNING: vmlinux.o(.text+0x1aeca5a): Section mismatch in reference from the function rndis_bind_config() to the function .init.text:rndis_init()
The function rndis_bind_config() references
the function __init rndis_init().
This is often because rndis_bind_config lacks a __init
annotation or the annotation of rndis_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do
because the ioremap() was the last thing we did. Also if we hit any of
the goto statements in the original code then it would have led to a
NULL dereference of "ehci". This bug was introduced in: 796bcae736
"USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]"
I modified the few lines in front a little so that my code didn't
obscure the return success code path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DEBUG is defined unconditionally, remove it as this clutters the message log.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ftdi product ID for Lenz LI-USB, a model train interface. This
was NOT tested against 2.6.35, but a similar patch was tested with the
CentOS 2.6.18-194.11.1.el5 kernel. It wasn't clear to me what
ordering is being used in ftdi_sio.c, so I inserted the ID after another
model train entry(SPROG_II).
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a isoc transfer bug reported by Sander Eikelenboom.
When ep->skip is set, endpoint ring dequeue pointer should be updated
when processed every missed td. Although ring dequeue pointer will also
be updated when ep->skip is clear, leave it intact during missed tds
processing may cause two issues:
1). If the very next valid transfer following missed tds is a short
transfer, its actual_length will be miscalculated;
2). If there are too many missed tds during transfer, new inserted tds
may found the transfer ring full and urb enqueue fails.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code to increment the TRB pointer has a slight ambiguity that could
lead to a bug on different compilers. The ANSI C specification does not
specify the precedence of the assignment operator over the postfix
operator. gcc 4.4 produced the correct code (increment the pointer and
assign the value), but a MIPS compiler that one of John's clients used
assigned the old (unincremented) value.
Remove the unnecessary assignment to make all compilers produce the
correct assembly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the ID for the Ionics PlugComputer (<http://ionicsplug.com/>).
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reset state of twl4030-usb is not sleeping, it starts
up awaken and we need to disable it if we have booted
with a disconnected cable to avoid over consumption on
the default state.
To avoid problems later, we read the current state of the
transceiver from the PHY_PWR_CTRL register. The bootloader
can, anyways, put the device to sleep before us.
Tested on a custom OMAP board.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warning(include/linux/usb/composite.h:284): No description found for parameter 'disconnect'
Warning(drivers/usb/gadget/composite.c:744): No description found for parameter 'c'
Warning(drivers/usb/gadget/composite.c:744): Excess function parameter 'cdev' description in 'usb_string_ids_n'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flag was never set in ssu100_process_packet. Add logic to set it
before calling tty_insert_flip_*
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a disconnect function to the functions of this device. The
disconnect is a call to usb_serial_generic_disconnect() so it requires
that symbol to be exported from generic.c.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed by the ssu100 driver to use this function.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the logic for TIOCMIWAIT to use wait_event_interruptible.
This also adds support for TIOCGICOUNT.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function ssu100_setregister was hard coded to only set the MCR
register. Add a register parameter so that other registers can be
set.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ssu100 uses a TI16C550C UART so the SERIAL_ defines in this code
are duplicates of those found in serial_reg.h. Remove the defines in
ssu100.c and use the ones in the header file.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The status information does not appear at the start of each incoming
packet so the check for len < 4 at the start of ssu100_process_packet
is wrong. Remove it.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>