Currently the skb->protocol field is used to setup checksum
offloading on transmit for the correct protocol. However, if
vlan offloading is disabled or otherwise not used, the protocol
field will be ETH_P_8021Q, not the actual protocol. This will
cause the checksum to be not computed correctly, even though the
hardware is capable of looking inside vlan tags. Instead,
look inside the header if necessary to determine the correct
protocol type.
To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on how a packet is vlan tagged (i.e. hardware accelerated or
not), the encapsulated protocol is stored in different locations. This
provides a consistent method of accessing that protocol, which is needed
by drivers, security checks, etc.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For device that supports VIRTIO_NET_F_STATUS, there's no need to
assume the link is up and we need to call nerif_carrier_off() before
querying device status, otherwise we may get wrong operstate after
diver was loaded because the link watch event was not fired as
expected.
For device that does not support VIRITO_NET_F_STATUS, we could not get
its status through virtnet_update_status() and what we can only do is
always assuming the link is up.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ucc_geth_close lacks a cancel_work_sync(&ugeth->timeout_work)
to stop any outstanding processing of TX fail. However, one
can not call cancel_work_sync without fixing the timeout function
otherwise it will deadlock. This patch brings ucc_geth in line with
gianfar:
Don't bring the interface down and up, just reinit controller HW
and PHY.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameter 'len' is size_t type so it will never get negative.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
nlmsg_total_size() calculates the length of a netlink message
including header and alignment. nla_total_size() calculates the
space an individual attribute consumes which was meant to be used
in this context.
Also, ensure to account for the attribute header for the
IFLA_INFO_XSTATS attribute as implementations of get_xstats_size()
seem to assume that we do so.
The addition of two message headers minus the missing attribute
header resulted in a calculated message size that was larger than
required. Therefore we never risked running out of skb tailroom.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: GIC: don't disable software generated interrupts
ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
ARM: 6462/1: EP93xx: Document DMA M2P API
ARM: 6470/1: atomic64: use generic implementation for OABI configurations
ARM: 6469/1: perf-events: squash compiler warning
ARM: 6468/1: backtrace: fix calculation of thread stack base
ARM: Fix DMA coherent allocator alignment
ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
[ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
ARM: pxa/saar: fix the building failure caused by typo
ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
ARM: pxa: fix the missing definition of IRQ_BOARD_END
ARM: mmp: fix cpuid detection on mmp2
[ARM] Kirkwood: restrict the scope of the PCIe reset workaround
[ARM] Kirkwood: fix timer initialization for LaCie boards
[ARM] Kirkwood: enhance TCLK detection
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: do not pass injected events back to the originating handler
Input: pcf8574_keypad - fix error handling in pcf8574_kp_probe
Input: acecad - fix a memory leak in usb_acecad_probe error path
Input: atkbd - add 'terminal' parameter for IBM Terminal keyboards
Input: i8042 - add Sony VAIOs to MUX blacklist
kgdboc: reset input devices (keyboards) when exiting debugger
Input: export input_reset_device() for use in KGDB
Input: adp5588-keys - unify common header defines
When a PCI bus has two resources with the same start/end, e.g.,
pci_bus 0000:04: resource 2 [mem 0xd0000000-0xd7ffffff pref]
pci_bus 0000:04: resource 7 [mem 0xd0000000-0xd7ffffff]
the previous pci_bus_find_resource_prev() implementation would alternate
between them forever:
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
returns [mem 0xd0000000-0xd7ffffff]
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff])
returns [mem 0xd0000000-0xd7ffffff pref]
pci_bus_find_resource_prev(... [mem 0xd0000000-0xd7ffffff pref])
returns [mem 0xd0000000-0xd7ffffff]
...
This happened because there was no ordering between two resources with the
same start and end. A resource that had the same start and end as the
cursor, but was not itself the cursor, was considered to be before the
cursor.
This patch fixes the hang by making a fixed ordering between any two
resources.
In addition, it tries to allocate from positively decoded regions before
using any subtractively decoded resources. This means we will use a
positive decode region before a subtractive decode one, even if it means
using a smaller address.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=22062
Reported-by: Borislav Petkov <bp@amd64.org>
Tested-by: Borislav Petkov <bp@amd64.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (27 commits)
block: remove unused copy_io_context()
Documentation: remove anticipatory scheduler info
block: remove REQ_HARDBARRIER
ioprio: rcu_read_lock/unlock protect find_task_by_vpid call (V2)
ioprio: fix RCU locking around task dereference
block: ioctl: fix information leak to userland
block: read i_size with i_size_read()
cciss: fix proc warning on attempt to remove non-existant directory
bio: take care not overflow page count when mapping/copying user data
block: limit vec count in bio_kmalloc() and bio_alloc_map_data()
block: take care not to overflow when calculating total iov length
block: check for proper length of iov entries in blk_rq_map_user_iov()
cciss: remove controllers supported by hpsa
cciss: use usleep_range not msleep for small sleeps
cciss: limit commands allocated on reset_devices
cciss: Use kernel provided PCI state save and restore functions
cciss: fix board status waiting code
drbd: Removed checks for REQ_HARDBARRIER on incomming BIOs
drbd: REQ_HARDBARRIER -> REQ_FUA transition for meta data accesses
drbd: Removed the BIO_RW_BARRIER support form the receiver/epoch code
...
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, amd: Use kmalloc_node(,__GFP_ZERO) for northbridge structure allocation
perf_events: Fix time tracking in samples
perf trace: update usage
perf trace: update Documentation with new perf trace variants
perf trace: live-mode command-line cleanup
perf trace record: handle commands correctly
perf record: make the record options available outside perf record
perf trace scripting: remove system-wide param from shell scripts
perf trace scripting: fix some small memory leaks and missing error checks
perf: Fix usages of profile_cpu in builtin-top.c to use cpu_list
perf, ui: Eliminate stack-smashing protection compiler complaint
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (39 commits)
drm/ttm: Be consistent on ttm_bo_init() failures
drm/radeon/kms: Fix retrying ttm_bo_init() after it failed once.
drm/radeon/kms: fix thermal sensor reporting on rv6xx
drm/radeon/kms: fix bugs in ddc and cd path router code
drm/radeon/kms: add support for clock/data path routers
drm: vmwgfx: fix information leak to userland
drivers/gpu: Use vzalloc
drm/vmwgfx: Fix oops on failing bo pin
drm/ttm: Remove the CAP_SYS_ADMIN requirement for bo pinning
drm/ttm: Make sure a sync object doesn't disappear while we use it
drm/radeon/kms: don't disable shared encoders on pre-DCE3 display blocks
drivers/gpu/drm: Update WARN uses
drivers/gpu/drm/vmwgfx: Fix k.alloc switched arguments
DRM: ignore invalid EDID extensions
drm/radeon/kms: make the connector code less verbose
drm/ttm: remove failed ttm binding error printout
drm/ttm: Add a barrier when unreserving
drm/ttm: Remove mm init error printouts and checks
drm/ttm: Remove pointless list_empty check
drm/ttm: Use private locks for the default bo range manager
...
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: remove incorrect assert in xfs_vm_writepage
xfs: use hlist_add_fake
xfs: fix a few compiler warnings with CONFIG_XFS_QUOTA=n
xfs: tell lockdep about parent iolock usage in filestreams
xfs: move delayed write buffer trace
xfs: fix per-ag reference counting in inode reclaim tree walking
xfs: xfs_ioctl: fix information leak to userland
xfs: remove experimental tag from the delaylog option
kobject_put is called from padata_free for the padata kobject.
The kobject's release function frees the padata instance,
so don't call kobject_put for the padata kobject from pcrypt.
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the MacBookAir3,1 and MacBookAir3,2 to the mbp-nvidia-bl
driver.
Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle return value, strict_strtoul is declared with attribute
warn_unused_result.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This affects the get/set of the current Ambient Light Zone. Reading
should return an integer between 1..3 (1 = Daylight, 2 = office, 3 =
dark). Writing a value between 1..3 forces the backlight controller to
enter the corresponding Ambient Light Zone. Writing 0 returns to normal
operation.
Fix valid range checking so we don't write invalid values to the
controller, and make sure we subtract 1, since this is what the register
definition (CFGR:BLV) requires. Otherwise the values written don't work
correctly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intensity of the backlight can be varied from a range of
max_brightness to zero. Though most, if not all the pwm based backlight
devices start flickering at lower brightness value. And also for each
device there exists a brightness value below which the backlight appears
to be turned off though the value is not equal to zero.
If the range of brightness for a device is from zero to max_brightness. A
graph is plotted for brightness Vs intensity for the pwm based backlight
device has to be a linear graph.
intensity
| /
| /
| /
|/
---------
0 max_brightness
But pratically on measuring the above we note that the intensity of
backlight goes to zero(OFF) when the value in not zero almost nearing to
zero(some x%). so the graph looks like
intensity
| /
| /
| /
| |
------------
0 x max_brightness
In order to overcome this drawback knowing this x% i.e nothing but the low
threshold beyond which the backlight is off and will have no effect, the
brightness value is being offset by the low threshold value(retaining the
linearity of the graph). Now the graph becomes
intensity
| /
| /
| /
| /
-------------
0 max_brightness
With this for each and every digit increment in the brightness from zero
there is a change in the intensity of backlight. Devices having this
behaviour can set the low threshold brightness(lth_brightness) and pass
the same as platform data else can have it as zero.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate section mismatch warning by marking s6e63m0_probe() as __devinit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Cc: InKi Dae <inki.dae@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD was turned on if the variable power was > 0, but that was
incorrect. The LCD has to be turned on in NORMAL and UNBLANK case.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD was turned on if the variable power was > 0, but that was
incorrect. The LCD has to be turned on in NORMAL and UNBLANK case.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gamma_table is not writable, so set permissions to 0444.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the event that none of the configs are set (CONFIG_LEDS_GPIO_PLATFORM,
CONFIG_LEDS_GPIO_OF, CONFIG_LEDS_GPIO_PLATFORM), we will return a bogus
value when initializing the module.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create sub directory Documentation/leds and add short documentation for
LP5521 and LP5523 drivers.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide configuration and compilation support for LP5521 and LP5523
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LP5523 chip is nine channel led driver with programmable engines. Driver
provides support for that chip for direct access via led class or via
programmable engines.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset provides support for LP5521 and LP5523 LED driver chips from
National Semicondutor. Both drivers supports programmable engines and
naturally LED class features.
Documentation is provided as a part of the patchset. I created "leds"
subdirectory under Documentation. Perhaps the rest of the leds*
documentation should be moved there.
Datasheets are freely available at National Semiconductor www pages.
This patch:
LP5521 chip is three channel led driver with programmable engines. Driver
provides support for that chip for direct access via led class or via
programmable engines.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, blinking LEDs can be awkward because it is not guaranteed that
all LEDs implement blinking. The trigger that wants it to blink then
needs to implement its own timer solution.
Rather than require that, add led_blink_set() API that triggers can use.
This function will attempt to use hw blinking, but if that fails
implements a timer for it. To stop blinking again, brightness_set() also
needs to be wrapped into API that will stop the software blink.
As a result of this, the timer trigger becomes a very trivial one, and
hopefully we can finally see triggers using blinking as well because it's
always easy to use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARN_ONCE is a bit strong for a deprecation warning, given that it spews a
huge backtrace.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Salman Qazi describes the following radix-tree bug:
In the following case, we get can get a deadlock:
0. The radix tree contains two items, one has the index 0.
1. The reader (in this case find_get_pages) takes the rcu_read_lock.
2. The reader acquires slot(s) for item(s) including the index 0 item.
3. The non-zero index item is deleted, and as a consequence the other item is
moved to the root of the tree. The place where it used to be is queued for
deletion after the readers finish.
3b. The zero item is deleted, removing it from the direct slot, it remains in
the rcu-delayed indirect node.
4. The reader looks at the index 0 slot, and finds that the page has 0 ref
count
5. The reader looks at it again, hoping that the item will either be freed or
the ref count will increase. This never happens, as the slot it is looking
at will never be updated. Also, this slot can never be reclaimed because
the reader is holding rcu_read_lock and is in an infinite loop.
The fix is to re-use the same "indirect" pointer case that requires a slot
lookup retry into a general "retry the lookup" bit.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Reported-by: Salman Qazi <sqazi@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel syslog contains debugging information that is often useful
during exploitation of other vulnerabilities, such as kernel heap
addresses. Rather than futilely attempt to sanitize hundreds (or
thousands) of printk statements and simultaneously cripple useful
debugging functionality, it is far simpler to create an option that
prevents unprivileged users from reading the syslog.
This patch, loosely based on grsecurity's GRKERNSEC_DMESG, creates the
dmesg_restrict sysctl. When set to "0", the default, no restrictions are
enforced. When set to "1", only users with CAP_SYS_ADMIN can read the
kernel syslog via dmesg(8) or other mechanisms.
[akpm@linux-foundation.org: explain the config option in kernel.txt]
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Eugene Teo <eugeneteo@kernel.org>
Acked-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/pid/oom_adj was deprecated in August 2010 with the introduction of
the new oom killer heuristic.
This patch copies the Documentation/feature-removal-schedule.txt entry for
this tunable to the Documentation/ABI/obsolete directory so nobody misses
it.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nr_dirty and nr_congested are increased only when the page is dirty. So
if all pages are clean, both them will be zero. In this case, we should
not mark the zone congested.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Per task latencytop accumulator prematurely terminates due to erroneous
placement of latency_record_count. It should be incremented whenever a
new record is allocated instead of increment on every latencytop event.
Also fix search iterator to only search known record events instead of
blindly searching all pre-allocated space.
Signed-off-by: Ken Chen <kenchen@google.com>
Reviewed-by: Arjan van de Ven <arjan@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
70 hours into some stress tests of a 2.6.32-based enterprise kernel, we
ran into a NULL dereference in here:
int block_is_partially_uptodate(struct page *page, read_descriptor_t *desc,
unsigned long from)
{
----> struct inode *inode = page->mapping->host;
It looks like page->mapping was the culprit. (xmon trace is below).
After closer examination, I realized that do_generic_file_read() does a
find_get_page(), and eventually locks the page before calling
block_is_partially_uptodate(). However, it doesn't revalidate the
page->mapping after the page is locked. So, there's a small window
between the find_get_page() and ->is_partially_uptodate() where the page
could get truncated and page->mapping cleared.
We _have_ a reference, so it can't get reclaimed, but it certainly
can be truncated.
I think the correct thing is to check page->mapping after the
trylock_page(), and jump out if it got truncated. This patch has been
running in the test environment for a month or so now, and we have not
seen this bug pop up again.
xmon info:
1f:mon> e
cpu 0x1f: Vector: 300 (Data Access) at [c0000002ae36f770]
pc: c0000000001e7a6c: .block_is_partially_uptodate+0xc/0x100
lr: c000000000142944: .generic_file_aio_read+0x1e4/0x770
sp: c0000002ae36f9f0
msr: 8000000000009032
dar: 0
dsisr: 40000000
current = 0xc000000378f99e30
paca = 0xc000000000f66300
pid = 21946, comm = bash
1f:mon> r
R00 = 0025c0500000006d R16 = 0000000000000000
R01 = c0000002ae36f9f0 R17 = c000000362cd3af0
R02 = c000000000e8cd80 R18 = ffffffffffffffff
R03 = c0000000031d0f88 R19 = 0000000000000001
R04 = c0000002ae36fa68 R20 = c0000003bb97b8a0
R05 = 0000000000000000 R21 = c0000002ae36fa68
R06 = 0000000000000000 R22 = 0000000000000000
R07 = 0000000000000001 R23 = c0000002ae36fbb0
R08 = 0000000000000002 R24 = 0000000000000000
R09 = 0000000000000000 R25 = c000000362cd3a80
R10 = 0000000000000000 R26 = 0000000000000002
R11 = c0000000001e7b60 R27 = 0000000000000000
R12 = 0000000042000484 R28 = 0000000000000001
R13 = c000000000f66300 R29 = c0000003bb97b9b8
R14 = 0000000000000001 R30 = c000000000e28a08
R15 = 000000000000ffff R31 = c0000000031d0f88
pc = c0000000001e7a6c .block_is_partially_uptodate+0xc/0x100
lr = c000000000142944 .generic_file_aio_read+0x1e4/0x770
msr = 8000000000009032 cr = 22000488
ctr = c0000000001e7a60 xer = 0000000020000000 trap = 300
dar = 0000000000000000 dsisr = 40000000
1f:mon> t
[link register ] c000000000142944 .generic_file_aio_read+0x1e4/0x770
[c0000002ae36f9f0] c000000000142a14 .generic_file_aio_read+0x2b4/0x770 (unreliable)
[c0000002ae36fb40] c0000000001b03e4 .do_sync_read+0xd4/0x160
[c0000002ae36fce0] c0000000001b153c .vfs_read+0xec/0x1f0
[c0000002ae36fd80] c0000000001b1768 .SyS_read+0x58/0xb0
[c0000002ae36fe30] c00000000000852c syscall_exit+0x0/0x40
--- Exception: c00 (System Call) at 00000080a840bc54
SP (fffca15df30) is in userspace
1f:mon> di c0000000001e7a6c
c0000000001e7a6c e9290000 ld r9,0(r9)
c0000000001e7a70 418200c0 beq c0000000001e7b30 # .block_is_partially_uptodate+0xd0/0x100
c0000000001e7a74 e9440008 ld r10,8(r4)
c0000000001e7a78 78a80020 clrldi r8,r5,32
c0000000001e7a7c 3c000001 lis r0,1
c0000000001e7a80 812900a8 lwz r9,168(r9)
c0000000001e7a84 39600001 li r11,1
c0000000001e7a88 7c080050 subf r0,r8,r0
c0000000001e7a8c 7f805040 cmplw cr7,r0,r10
c0000000001e7a90 7d6b4830 slw r11,r11,r9
c0000000001e7a94 796b0020 clrldi r11,r11,32
c0000000001e7a98 419d00a8 bgt cr7,c0000000001e7b40 # .block_is_partially_uptodate+0xe0/0x100
c0000000001e7a9c 7fa55840 cmpld cr7,r5,r11
c0000000001e7aa0 7d004214 add r8,r0,r8
c0000000001e7aa4 79080020 clrldi r8,r8,32
c0000000001e7aa8 419c0078 blt cr7,c0000000001e7b20 # .block_is_partially_uptodate+0xc0/0x100
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: <arunabal@in.ibm.com>
Cc: <sbest@us.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clean_sort_range() should return a number of nonempty elements of range
array, but if the array is full clean_sort_range() returns 0.
The problem is that the number of nonempty elements is evaluated by
finding the first empty element of the array. If there is no such element
it returns an initial value of local variable nr_range that is zero.
The fix is trivial: it changes initial value of nr_range to size of the
array.
The bug can lead to loss of information regarding all ranges, since
typically returned value of clean_sort_range() is considered as an actual
number of ranges in the array after a series of add/subtract operations.
Found by Analytical Verification project of Linux Verification Center
(linuxtesting.org), thanks to Alexander Kolosov.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a signedness bug so "ret" was never less than zero and that
breaks the error handling. Also in the original code it would overwrite
ret and the result is still negative but it's bogus number instead of the
correct error code.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original code had a null dereference if alloc_percpu() failed. This
was introduced in commit 711d3d2c9b ("memcg: cpu hotplug aware percpu
count updates")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2c_smbus_read_byte_data() may return negative error code. This is not
seen to als_sensing_range_store() as the result is stored in unsigned int.
Made it signed.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Hong Liu <hong.liu@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Anantha Narayanan <anantha.narayanan@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"ret_val" is supposed to be signed here or the error handling breaks.
Also we should check the return value from i2c_smbus_read_byte_data().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3e4d3af501 ("mm: stack based kmap_atomic()") introduced the
kmap_atomic_idx_push() function which warns on in_irq() with
CONFIG_DEBUG_HIGHMEM enabled. This patch includes linux/hardirq.h for
the in_irq definition.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Followup of perf tools session in Netfilter WorkShop 2010
In the network stack we make high usage of atomic_inc_not_zero() in
contexts we know the probable value of atomic before increment (2 for udp
sockets for example)
Using a special version of atomic_inc_not_zero() giving this hint can help
processor to use less bus transactions.
On x86 (MESI protocol) for example, this avoids entering Shared state,
because "lock cmpxchg" issues an RFO (Read For Ownership)
akpm: Adds a new include/linux/atomic.h. This means that new code should
henceforth include linux/atomic.h and not asm/atomic.h. The presence of
include/linux/atomic.h will in fact cause checkpatch.pl to warn about use
of asm/atomic.h. The new include/linux/atomic.h becomes the place where
arch-neutral atomic_t code should be placed.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warning:
usr/include/linux/resource.h:49: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hao Zheng
Jason Wang
Joakim Tjernlund
Mariusz Kozlowski
David S. Miller
Thomas Graf
Linus Torvalds
Bjorn Helgaas
Steffen Klassert
Edgar (gimli) Hucek
Michael Hennerich
Arun Murthy
Axel Lin
Marek Vasut
Davidlohr Bueso
Samu Onkalo
Johannes Berg
Dave Jones
Nick Piggin
Dan Rosenberg
David Rientjes
Shaohua Li
Ken Chen
Dave Hansen
Alexey Khoroshilov
Dan Carpenter
Vasiliy Kulikov
Catalin Marinas
Eric Dumazet
Jean Delvare