3-stack is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.
Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function is defined once for each imx family and so is in the way
when compiling a kernel for more than one SoC.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.
This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch enables usb gadget for freescale mx51 babbage hw. By default,
the OTG port will be in device mode. To put the OTG port into Host mode,
pass "otg_mode=host" in the exec command.
This patch applies to 2.6.34-rc7.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For power management reasons, pll2 should be used to source the USBOH3
clock for mx51. PLL3 can be completely gated off when USB is not used.
This patch applies to 2.6.34-rc7.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch enables USB host functionality for Host1 and OTG port on
Freescale MX51 Babbage HW. This patch contains the board specific
HW initialization of the USB HW.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is part of enabling USB for Freescale MX51 Babbage HW. This
patch adds device structures for USB Host1 and OTG port, and adds
clocking information for USB HW.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Need to include <asm/div64.h> for do_div calls.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This area contains the Nand Flash controller registers. There
is no need to map them statically as the Nand driver uses ioremap().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Freescale redboot passes the silicon revision via
ATAG_REVISION. Remove this bootloader dependency by
doing the same as redboot does in the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This looks cleaner and allows us to call mx51_revision
later when we can use ioremap to determine the silicon
revision dynamically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is to be applied into Sascha's mxc-master branch.
Fix ckih2 parameter in mx51_clocks_init funtion. CKIH2 pin is left unconnected on Babbage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Babbage is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefiles to enable Freescale i.MX51
processor and Babbage board.
Boot tested on a Babbage2.5 board
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Add basic clock support, cpu identification, I/O mapping, interrupt
controller, serial port and ethernet.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Jason Wang