The VM subsystem assumes that there are valid memmap entries from
the bank start aligned to MAX_ORDER_NR_PAGES.
On the Ux500 we have a lot of mem=N arguments on the commandline
triggering this bug several times over and causing kernel
oops messages.
Cc: stable@kernel.org
Cc: Michael Bohan <mbohan@codeaurora.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Johan Palsson <johan.palsson@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the attempt to map a page for DMA fails (eg, because we're out of
mapping space) then we must not hold on to the page we allocated for
DMA - doing so will result in a memory leak.
Cc: <stable@kernel.org>
Reported-by: Bryan Phillippe <bp@darkforest.org>
Tested-by: Bryan Phillippe <bp@darkforest.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements a workaround for erratum 764369 affecting
Cortex-A9 MPCore with two or more processors (all current revisions).
Under certain timing circumstances, a data cache line maintenance
operation by MVA targeting an Inner Shareable memory region may fail to
proceed up to either the Point of Coherency or to the Point of
Unification of the system. This workaround adds a DSB instruction before
the relevant cache maintenance functions and sets a specific bit in the
diagnostic control register of the SCU.
Cc: <stable@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit be020f8618, "ARM: entry: abort-macro: specify registers to be
used for macros", while replacing register numbers with macro parameter
names, mismatched the name used for r1. For me, this resulted in user
space built for EABI with -march=armv4t -mtune=arm920t -mthumb-interwork
-mthumb broken on my OMAP1510 based Amstrad Delta (old ABI and no thumb
still worked for me though).
Fix this by using correct parameter name fsr instead of mismatched psr,
used by callers for another purpose.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fighting unfixed U-Boots and other beasts that may the cache in
a locked-down state when starting the kernel, we make sure to
disable all cache lock-down when initializing the l2x0 so we
are in a known state.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Adrian Bunk <adrian.bunk@movial.com>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Jan Rinze <janrinze@gmail.com>
Tested-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ARCH_HAS_HOLES_MEMORYMODEL is selected, pfn_valid calls
memblock_is_memory to test validity of a pfn:
> memblock_is_memory(pfn << PAGE_SHIFT);
On LPAE systems this cuts off the top bits, as the shift occurs before
the value is promoted to a phys_addr_t.
This patch replaces the shift with a call to __pfn_to_phys (which casts
pfn to phys_addr_t before shifting), preventing the loss of significant
bits.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register. If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM920 and ARM926 save four registers, not three. Fix the size of
the suspend region required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code. Overwriting it is
not a good idea.
We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration. So fix this latent bug.
This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is a workaround for the 364296 ARM1136 r0p2 erratum (possible
cache data corruption with hit-under-miss enabled). It sets the
undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the UM_SIGNAL alignment fault mode, no siginfo structure is
passed to userspace.
POSIX specifies how siginfo_t should be populated for alignment
faults, so this patch does just that:
* si_signo = SIGBUS
* si_code = BUS_ADRALN
* si_addr = misaligned data address at which access was attempted
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, it's possible to set the kernel to ignore alignment
faults when changing the alignment fault handling mode at runtime
via /proc/sys/alignment, even though this is undesirable on ARMv6
and above, where it can result in infinite spins where an un-fixed-
up instruction repeatedly faults.
In addition, the kernel clobbers any alignment mode specified on
the command-line if running on ARMv6 or above.
This patch factors out the necessary safety check into a couple of
new helper functions, and checks and modifies the fault handling
mode as appropriate on boot and on writes to /proc/cpu/alignment.
Prior to ARMv6, the behaviour is unchanged.
For ARMv6 and above, the behaviour changes as follows:
* Attempting to ignore faults on ARMv6 results in the mode being
forced to UM_FIXUP instead. A warning is printed if this
happened as a result of a write to /proc/cpu/alignment. The
user's UM_WARN bit (if present) is still honoured.
* An alignment= argument from the kernel command-line is now
honoured, except that the kernel will modify the specified mode
as described above. This is allows modes such as UM_SIGNAL and
UM_WARN to be active immediately from boot, which is useful for
debugging purposes.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
poison_init_mem() used a loop of:
while ((count = count - 4))
which has 2 problems - an off by one error so that we do one less word
than we should, and the other is that if count == 0 then we loop forever
and poison too much. On a platform with HAVE_TCM=y but nothing in the
TCM's, this caused corruption and the platform failed to boot.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The file mm/proc-arm946.S contains a typo and is missing a structure
member in __arm946_proc_info. The former prevents compilation
and the latter causes problems during boot. It is likely this
file was manually copied from a similar file and not tested, then
later updates to the *_proc_info structures missed this file.
This patch will apply (with offset) with or without the
recent macro unification work that has been done in this directory.
This was verified against linux-next/stable last week.
See arm-linux-kernel thread:
http://lists.arm.linux.org.uk/lurker/message/20110718.103237.0106d468.en.html
Signed-off-by: Brian S. Julin <bri@abrij.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
MAINTAINERS: add maintainer of CSR SiRFprimaII machine
ARM: CSR: initializing L2 cache
ARM: CSR: mapping early DEBUG_LL uart
ARM: CSR: Adding CSR SiRFprimaII board support
OMAP4: clocks: Update the clock tree with 4460 clock nodes
OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
OMAP4: ID: add omap_has_feature for max freq supported
OMAP: ID: introduce chip detection for OMAP4460
ARM: Xilinx: merge board file into main platform code
ARM: Xilinx: Adding Xilinx board support
Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
perf: Remove the nmi parameter from the oprofile_perf backend
x86, perf: Make copy_from_user_nmi() a library function
perf: Remove perf_event_attr::type check
x86, perf: P4 PMU - Fix typos in comments and style cleanup
perf tools: Make test use the preset debugfs path
perf tools: Add automated tests for events parsing
perf tools: De-opt the parse_events function
perf script: Fix display of IP address for non-callchain path
perf tools: Fix endian conversion reading event attr from file header
perf tools: Add missing 'node' alias to the hw_cache[] array
perf probe: Support adding probes on offline kernel modules
perf probe: Add probed module in front of function
perf probe: Introduce debuginfo to encapsulate dwarf information
perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
perf probe: Remove redundant dwarf functions
perf probe: Move strtailcmp to string.c
perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
tracing/kprobe: Update symbol reference when loading module
tracing/kprobes: Support module init function probing
kprobes: Return -ENOENT if probe point doesn't exist
...
Commit 66a625a (ARM: mm: proc-macros: Add generic proc/cache/tlb struct
definition macros) introduced build errors when PM_SLEEP is not enabled.
The per-CPU do_suspend/do_resume functions are defined via the
preprocessor to constant 0. However, the macros which use these were
converted to assembly, resulting in undefined references to these
functions. Fix that by moving the ! ifdef section into proc-macros.S
and deleting it from all effected proc-*.S files.
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently using just long but this is not enough for the LPAE format
(64-bit entries).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel space needs very little in the way of BTC maintanence as most
mappings which are created and destroyed are non-executable, and so
could never enter the instruction stream.
The case which does warrant BTC maintanence is when a module is loaded.
This creates a new executable mapping, but at that point the pages have
not been initialized with code and data, so at that point they contain
unpredictable information. Invalidating the BTC at this stage serves
little useful purpose.
Before we execute module code, we call flush_icache_range(), which deals
with the BTC maintanence requirements. This ensures that we have a BTC
maintanence operation before we execute code via the newly created
mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Having this value defined at compile time prevents multiple machines with
conflicting definitions to coexist. Move it to a variable in preparation
for having a per machine value selected at run time. This is relevant
only when CONFIG_ZONE_DMA is selected.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Convert the incorrectly named PCIMEM_BASE to a variable called vga_base.
This removes the dependency on mach/hardware.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM to variables to allow
multi-platform builds. This also removes the requirement for a platform to
have a mach/hardware.h.
The default values for i/o and mem are 0x1000 and 0x01000000, respectively.
Per Arnd Bergmann, other values are likely to be incorrect, but this commit
does not try to address that issue.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert pcibios_assign_all_busses from a define to inline so platforms can
control this setting.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Remove some includes of mach/hardware.h which are not needed. hardware.h
will be removed completely for tegra and cns3xxx in follow on patch.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
ISA_DMA_THRESHOLD has been unused by non-arch code, so lets now get
rid of it from ARM by replacing it with arm_dma_zone_mask. Move
dma_supported() and dma_set_mask() out of line, and have
dma_supported() check this new variable instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SiRFprimaII is the latest generation application processor from CSR’s
Multifunction SoC product family. Designed around an ARM cortex A9 core,
high-speed memory bus, advanced 3D accelerator and full-HD multi-format
video decoder, SiRFprimaII is able to meet the needs of complicated
applications for modern multifunction devices that require heavy concurrent
applications and fluid user experience. Integrated with GPS baseband,
analog and PMU, this new platform is designed to provide a cost effective
solution for Automotive and Consumer markets.
This patch adds the basic support for this SoC and EVB board based on device
tree. It is following the ZYNQ of Xilinx in some degree.
Signed-off-by: Binghua Duan <Binghua.Duan@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Yuping Luo <Yuping.Luo@csr.com>
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Huayi Li <Huayi.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Originally introduced to maintain coherency between icache and dcache
in v6 nonaliasing mode. This is now handled by __sync_icache_dcache since
c0177800, therefore unnecessary in this function.
Signed-off-by: Heechul Yun <heechul@illinois.edu>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Poisoning __init marked memory can be useful when tracking down
obscure memory corruption bugs. Therefore, poison init memory
with 0xe7fddef0 to catch bugs earlier. The poison value is an
undefined instruction in ARM mode and branch to an undefined
instruction in Thumb mode.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Place the init sections between the text and data sections. This
means all code is grouped together at the beginning of the kernel
image, and all data is at the end of the image. This avoids problems
with the 24-bit branch instruction relocations becoming invalid with
large initramfs images.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds simple definitions of cpu_reset for ARMv6 and ARMv7
cores, which disable the MMU via the SCTLR.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Multicore implementations of the Cortex-A15 require bit 6 of the
auxiliary control register to be set in order for cache and TLB
maintenance operations to be broadcast between CPUs.
This patch adds a new proc_info structure for Cortex-A15, which enables
the SMP bit during setup and includes the new HWCAP for integer
division.
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds processor info for ARM Ltd. Cortex A5,
which has SCU initialisation procedure identical to A9.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As most of the proc info content is common across all v7
processors, this patch converts existing A9 and generic v7
descriptions into a macro (allowing extra flags in future).
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CNS3xxx SOCs have L310-compatible cache controller, so let's use it.
With this patch benchmarking with 'gzip' shows that performance is
doubled, and I'm still able to boot full-fledged userland over NFS
(using PCIe NIC), so the support should be pretty robust.
p.s. While CNS3xxx reports that it has PL310, it still needs to wait
on cache line operations, so we should not select 'CACHE_PL310',
which is a micro-optimization that removes these waits for v7 CPUs.
Someday we'd better rename CACHE_PL310 Kconfig option into
NO_CACHE_WAIT or something less ambiguous.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Linus Walleij
Russell King
Will Deacon
Janusz Krzysztofik
Mark Rutland
Catalin Marinas
Dave Martin
Jamie Iles
Brian S. Julin
Linus Torvalds
Nicolas Pitre
Arnd Bergmann
Rob Herring
Binghua Duan
Heechul Yun
Stephen Boyd
Pawel Moll
Anton Vorontsov