This unifies the places that bounce the device (suspend/resume
and restart). And makes the operations have the same semantics
as normal dev_open/dev_stop.
This also avoids setting the multicast addresses twice when
device is brought up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suspend and shutdown code plays with shared state. Use consistent
locking, for extra protection.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid any possible problems with accessing PHY registers on shutdown.
This is a purely theoretical issue and is not related to any of the
outstanding bug reports. Since receiver and transmitter are already
shutdown and phy interrupts for this device are already disabled,
there should already be enough protection. Suggested by Mike McCormack.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reseting the tx chain too soon results in invalid tx queue positions
being delivered in the status queue. This also makes sure there's no
overlap between the cleanup done by sky2_tx_clean() and
sky2_tx_done().
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is pure refactoring.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep sky2->tx_prod consistent since int might be examined by
an softirq poll or restart.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also implement get/set BB mult, get/set TX gain, set RX gain,
disable/restore CRS, run/stop DDFS, RX IQ est and QDIV roundup
in the process.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k_stop() where the HW
was not put into FULL_SLEEP state. Not doing so will
cause issues in suspend-resume and the HW will not respond
to chip resets.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where the device was enabled
before restoring the PCI state.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diversity_control and antenna_switch_swap are already
present in ath9k_ops_config. Remove duplicate occurrences
in ath_hw.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY counters are available in all chipsets supported
by ath9k. Remove the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports the AR9002 family of chipsets. This includes
the AR9285 and the miniPCI AR9223 and AR9220 (which themselves
have AR9280+AR5133).
We now refer people to the wiki page as it seems this is not
as popular as we would have hoped.
Reported-by: JD <jd1008@gmail.com>
Cc: Dakota Lee <Dakota.Lee@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes drivers might have a good reason to override
the PS default, like iwlwifi right now where it affects
RX performance significantly at this point. This will
allow them to override the default, if desired, in a
way that users can still change it according to their
trade-off choices, not the driver's, like would happen
if the driver just disabled PS completely then.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you trigger a scan request on an interface and then
take it down, or rmmod the module or unplug the device
the driver might "forget" to cancel the scan request.
That is a bug in the driver, but the current behaviour
is that we just hang endlessly waiting for the netdev
refcount to become 0 which it never will. To improve
robustness, check for this situation in cfg80211, warn
about it and clean up behind the driver. I don't just
clean up silently because it's likely that the driver
also has some internal state it has now leaked.
Additionally, this fixes a locking bug, clearing the
scan_req pointer should be done under the rdev lock.
Finally, we also need to _wait_ for the scan work and
not just abort it since it might be pending and wanting
to do a cleanup.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the fixed portion of plink confirm frames is 4 bytes longer than
the other plink_action frames. This path corrects an error in the length
adjustment done for these type of frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a PREQ frame is received giving us a fresher DSN than what we have, record
the new dsn and mark it as valid. This patch fixes a bug in the setting of the
MESH_PATH_DSN_VALID flag.
Also, minor fix to coding style on that file.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This matches ath9k, providing consistency when reading both drivers.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that its shared we can remove ath5k's own implementation.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turns out ath5k and ath9k can share the same helper to
allocates RX skbs. We allocate skbs aligned to the cache line
size. This requirement seems to have come from AR5210; when
this was not done it seems sometimes we'd get bogus data. I'm
also told it may have been a performance enhancement
consideration. In the end I can't be sure we can remove this
on new hardware so just keep this and start sharing it through
ath.ko.
Make ath9k start using this, ath5k is next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reported that IRQ_MASK conflicts with include/pcmcia/cs.h on
compat-wireless. Remove that and a bunch of other unused defines
from wl1251_reg.h.
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "wl1251: remove wl1251_ops" originally removed file wl1251_ops.c,
but while I rebased the patch the removal got lost. Now remote the file
for real.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "iwlwifi: Traffic type and counter for debugFs" broke iwl3945 in
a case when CONFIG_IWLWIFI_LEDS is disabled:
drivers/net/wireless/iwlwifi/iwl-3945.c:580: error: 'hdr' undeclared (first use in this function)
Fix it by removing the ifdef check for hdr variable.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it possible to write individual gain table entries.
Allow gain table entries to be written outside gain table init.
Add version-agnostic helpers for writing gain tables.
Use the new TX gain table helpers during table init.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rx queue pausing to usbnet. This is needed by rndis_wlan so that it can
control rx queue and prevent received packets from being send forward before
rndis_wlan receives and handles 'media connect'-indication. Without this
establishing WPA connections is hard and fail often.
[v2] - removed unneeded use of skb_clone
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the new variables in b43_phy_lp appear to be dead code in
the vendor driver; they will be removed if they remain unused when
LP-PHY implementation is finished.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices created by the libertas driver are currently called eth%d. Which
is wrong, because the device does not at all have anything to do with
Ethernet. And it is also confusing when used on devices with more than
one network device.
Fix this by calling it wlan%d.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh frames that could not be immediately resolved were queued with a NULL
info->control.vif. This patch moves the call to mesh_nexthop_lookup closer to
the point where it is handed over to ieee80211_tx(). This ensures that the
unresolved frames are ready to be sent once the path is resolved.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a few warnings when compiling the wl1271 driver on 64 bit
architectures. This was due to size mismatch of integers.
This commit fixes the following warnings:
drivers/net/wireless/wl12xx/wl1271_main.c: In function 'wl1271_irq_work':
drivers/net/wireless/wl12xx/wl1271_main.c:184: warning: large integer implicitly truncated to unsigned type
drivers/net/wireless/wl12xx/wl1271_boot.c: In function 'wl1271_boot_upload_firmware_chunk':
drivers/net/wireless/wl12xx/wl1271_boot.c:103: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
drivers/net/wireless/wl12xx/wl1271_boot.c:150: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
drivers/net/wireless/wl12xx/wl1271_boot.c: In function 'wl1271_boot_enable_interrupts':
drivers/net/wireless/wl12xx/wl1271_boot.c:278: warning: large integer implicitly truncated to unsigned type
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I completely missed the "one's complement" instruction from the specs.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a "SPEX32" macro for extracting 32-bit SPROM variables.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents calling rcu_synchronize from within the tx path by moving the
table growth code to the mesh workqueue.
Move mesh_table_free and mesh_table_grow from mesh.c to mesh_pathtbl.c and
declare them static.
Also, re-enable mesh in Kconfig and update the configuration description.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh stack was enabling beaconing without specifying an interval. This
patch defines a default beaconing interval of 1s.
Incidentally, this fixes mesh beaconing in mac80211_hwsim devices.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change triggers a path discovery as soon as the link quality degrades
below a certain threshold. This results in a faster path recovery time than
by simply relying on the periodic path refresh mechanism to detect broken
links.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fail_avg value is used to compute the mesh metric, and was only being set
by the pid rate control module. This fixes the mesh path selection mechanism
for cards that use mistrel for rate control.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address. This was done to avoid interactions with widely
deployed lazy-WDS access points.
This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward. The
address fields used for group addressed frames is:
In 802.11 header
ToDS:0 FromDS:1
addr1: DA (broadcast/multicast address)
addr2: TA
addr3: Mesh SA
In address extension header:
addr4: SA (only present if frame was proxied)
Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On locally originated traffic, we refresh active paths after a timeout. The
decision to do this was using the wrong sign and therefore the refresh timer
was triggered for every frame.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, fix typo in comment.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rev2+ BB init spec has changed behind us, and thus the code is
no longer up to date. Update the code to match the current specs.
Also implement save/restore dig filt state, as required by the
new specification.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement LP-PHY baseband table init for all revisions.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's really easier to read if it's not indented
as much, so invert the condition and rearrange
the code so the smaller chunk is indented instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to mask the variable with 0xFFF0
since we ever only use it as a u16 and the lowest
four bits can't ever be non-zero. The compiler
cannot infer the latter, and therefore has to emit
code to do the masking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When encryption is used, the number of bytes
sent to the peer increases by the IV and ICV.
This is accounted if software encryption is
used, but not if the devices does hardware
encryption. To make the numbers comparable,
never account for that overhead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add maintainer information section for the wl1271 wireless driver and fix the
information for wl1271.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Get rid of calibration timer, instead use a software interrupt
to schedule the calibration tasklet.
a) We don't need a timer for this, there is no need for accuracy
even with round_jiffies i think this is a waste of resources.
Also we don't need to run calibration if we are idle (no
interrupts).
b) When we add ANI support we 'll just extend the poll function
and calibration tasklet and handle all periodic phy calibration
on one place (much cleaner).
c) Having calibration on a tasklet is better since during calibration
we can't transmit or receive (antennas are detached to measure
noise floor), previously calibration could run in parallel with
tx/rx and interfere (packet loss).
v2: kill tasklet on stop_hw, stop/wake queues
v3: use time_is_before_eq_jiffies to compare timestamp with current
time
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* During attach preserve pcicfg bits when enabling pci core
sw retry fix.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Don't put chip to full sleep because there are problems during
wakeup. Instead hold MAC/Baseband on warm reset state via a new
function ath5k_hw_on_hold.
* Minor cleanups
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
