Commit Graph

207 Commits

Author SHA1 Message Date
Serge Semin 87976ce282 hwmon: Add Baikal-T1 PVT sensor driver
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.

The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.

The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.

Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-28 07:59:45 -07:00
Guenter Roeck 8054eadca7 Immutable branch between MFD and HWMON due for the v5.8 merge window
-----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAl7E+JkACgkQUa+KL4f8
 d2G0Og/9Ebgnn3cmiQTUcxHPgtFu9PNWy+pEhnQ9my8RyPH+zJh7UKadCxIaO/FZ
 rmqzZCCETJR+zCVuRDBtSYwdSkhrkxo1Jm9HUVajx/3uiKIspK6anJ+CisKtcMNS
 Ouo/7ycAAzBjqShq+IJorsc1q9cCO0dt14Fffyjva8fiMYxGaJKrkNdtk49epXCy
 IJ953y3jgpxxB0A4ecnDE7qKXaw65mPhSv90XVDmPDxTajcGBKqP0es9cYzdlnqs
 yVfHxuT2dRU8tTs7J+o8DNGlSlxaWl/4tYdcpUb03VYwKFbrUFWL6bKoJ1riKUOR
 QloK7ytgeWP2m8vsfMzL8JMkBKDLamPu5+YoRRDp8AtfEVG09WgpJsUBOV3sLLUI
 o3gmsv04WGzGf7Ps0InmICrwMKvwPhJMxqkXCWUbGoDxECnRLBGGT25JA3EYoMYn
 RvUE5H+dvZUH2MRjSS50ADK/XuhEg2bQPwl/tpRzuEguYYgjGy08FzamfraGVk+D
 5JDSKkwcW17GgHIjVfPyKG5Nq09GNSigWy1BR/r+Gof8TtiJ9o5tq5FcZ9zH0JZZ
 QRhrsU1wCHHMY93mmJMWU5WYzltqXXasLaoveWLTpWfjfaaChzUu3YtFLFo5yFGm
 8M7EkDHyOTXJUc3MZySBgIfM0l93sQgvG6Qq0kcjQy2Sa0BwuNo=
 =FJTL
 -----END PGP SIGNATURE-----

Merge tag 'ib-mfd-hwmon-v5.8' into hwmon-next

Immutable branch between MFD and HWMON due for the v5.8 merge window
2020-05-22 06:29:55 -07:00
Naveen Krishna Chatradhi 8abee9566b hwmon: Add amd_energy driver to report energy counters
This patch adds hwmon based amd_energy driver support for
family 17h processors from AMD.

The driver provides following interface to the userspace
1. Reports the per core consumption
	* file: "energy%d_input", label: "Ecore%03d"
2. Reports per socket energy consumption
	* file: "energy%d_input", label: "Esocket%d"
3. To, increase the wrap around time of the socket energy
   counters, a 64bit accumultor is implemented.
4. Reports scaled energy value in Joules.

Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200519155011.56184-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-05-22 06:28:38 -07:00
Tim Harvey 3bce5377ef hwmon: Add Gateworks System Controller support
The Gateworks System Controller has a hwmon sub-component that exposes
up to 16 ADC's, some of which are temperature sensors, others which are
voltage inputs. The ADC configuration (register mapping and name) is
configured via device-tree and varies board to board.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2020-05-20 10:29:17 +01:00
Nuno Sá 8412b410fa hwmon: Support ADI Fan Control IP
The purpose of this IP Core is to control the fan used for the cooling of a
Xilinx Zynq Ultrascale+ MPSoC without the need of any external temperature
sensors. To achieve this, the IP core uses the PL SYSMONE4 primitive to
obtain the PL temperature and, based on those readings, it then outputs
a PWM signal to control the fan rotation accordingly.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191009102806.262241-1-nuno.sa@analog.com
[groeck: adi,pulses-per-revolution -> pulses-per-revolution;
 dropped unused 'res' from probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-03-08 20:35:46 -07:00
Beniamin Bia 09b08ac9e8 hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
ADM1177 is a Hot Swap Controller and Digital Power Monitor with
Soft Start Pin.

Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Link: https://lore.kernel.org/r/20200114112159.25998-1-beniamin.bia@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:11 -08:00
Guenter Roeck 5b46903d8b hwmon: Driver for disk and solid state drives with temperature sensors
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.

This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.

With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:

$ sensors drivetemp-scsi-1-0
drivetemp-scsi-1-0
Adapter: SCSI adapter
temp1:        +23.0°C

or directly from sysfs:

$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000

If the drive supports SCT transport and reports temperature limits,
those are reported as well.

drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1:        +27.0°C  (low  =  +0.0°C, high = +60.0°C)
                       (crit low = -41.0°C, crit = +85.0°C)
                       (lowest = +23.0°C, highest = +34.0°C)

The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.

Cc: Chris Healy <cphealy@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:10 -08:00
Guenter Roeck d21ed22ba7 hwmon: Driver for MAX31730
MAX31730 is a 3-Channel Remote Temperature Sensor.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2020-01-23 13:15:09 -08:00
Eric Tremblay 59dfa75e5d hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.
TI's TMP512/513 are I2C/SMBus system monitor chips. These chips
monitor the supply voltage, supply current, power consumption
and provide one local and up to three (TMP513) remote temperature sensors.

It has been tested using a TI TMP513 development kit (TMP513EVM)

Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
Link: https://lore.kernel.org/r/20191112223001.20844-3-etremblay@distech-controls.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-21 21:26:40 -08:00
Nuno Sá 9f90fd652b hwmon: Add support for ltc2947
The ltc2947 is a high precision power and energy monitor with an
internal sense resistor supporting up to +/- 30A. Three internal no
Latency ADCs ensure accurate measurement of voltage and current, while
high-bandwidth analog multiplication of voltage and current provides
accurate power measurement in a wide range of applications. Internal or
external clocking options enable precise charge and energy measurements.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191021154115.319073-1-nuno.sa@analog.com
[groeck: Removed unnecessary checks when reading temperature and energy;
	 PAGE{0,1} -> LTC2947_PAGE_{0,1}]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00
Linus Torvalds 5c6bd5de3c Main MIPS changes for v5.4:
- boot_mem_map is removed, providing a nice cleanup made possible by the
   recent removal of bootmem.
 
 - Some fixes to atomics, in general providing compiler barriers for
   smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
   MIPS32 systems using cmpxchg64().
 
 - Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
   Frascino.
 
 - Removal of undefined behavior in set_io_port_base(), fixing the
   behavior of some MIPS kernel configurations when built with recent
   clang versions.
 
 - Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
 
 - pte_special() is now supported for some configurations, allowing among
   other things generic fast GUP to be used.
 
 - Miscellaneous fixes & cleanups.
 
 And platform specific changes:
 
 - Major improvements to Ingenic SoC support from Paul Cercueil, mostly
   enabled by the inclusion of the new TCU (timer-counter unit) drivers
   he's spent a very patient year or so working on. Plus some fixes for
   X1000 SoCs from Zhou Yanjie.
 
 - Netgear R6200 v1 systems are now supported by the bcm47xx platform.
 
 - DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
 -----BEGIN PGP SIGNATURE-----
 
 iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
 b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
 4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
 =lWlM
 -----END PGP SIGNATURE-----

Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

Pull MIPS updates from Paul Burton:
 "Main MIPS changes:

   - boot_mem_map is removed, providing a nice cleanup made possible by
     the recent removal of bootmem.

   - Some fixes to atomics, in general providing compiler barriers for
     smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
     or MIPS32 systems using cmpxchg64().

   - Conversion to the new generic VDSO infrastructure courtesy of
     Vincenzo Frascino.

   - Removal of undefined behavior in set_io_port_base(), fixing the
     behavior of some MIPS kernel configurations when built with recent
     clang versions.

   - Initial MIPS32 huge page support, functional on at least Ingenic
     SoCs.

   - pte_special() is now supported for some configurations, allowing
     among other things generic fast GUP to be used.

   - Miscellaneous fixes & cleanups.

  And platform specific changes:

   - Major improvements to Ingenic SoC support from Paul Cercueil,
     mostly enabled by the inclusion of the new TCU (timer-counter unit)
     drivers he's spent a very patient year or so working on. Plus some
     fixes for X1000 SoCs from Zhou Yanjie.

   - Netgear R6200 v1 systems are now supported by the bcm47xx platform.

   - DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"

* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
  MIPS: Detect bad _PFN_SHIFT values
  MIPS: Disable pte_special() for MIPS32 with RiXi
  MIPS: ralink: deactivate PCI support for SOC_MT7621
  mips: compat: vdso: Use legacy syscalls as fallback
  MIPS: Drop Loongson _CACHE_* definitions
  MIPS: tlbex: Remove cpu_has_local_ebase
  MIPS: tlbex: Simplify r3k check
  MIPS: Select R3k-style TLB in Kconfig
  MIPS: PCI: refactor ioc3 special handling
  mips: remove ioremap_cachable
  mips/atomic: Fix smp_mb__{before,after}_atomic()
  mips/atomic: Fix loongson_llsc_mb() wreckage
  mips/atomic: Fix cmpxchg64 barriers
  MIPS: Octeon: remove duplicated include from dma-octeon.c
  firmware: bcm47xx_nvram: Allow COMPILE_TEST
  firmware: bcm47xx_nvram: Correct size_t printf format
  MIPS: Treat Loongson Extensions as ASEs
  MIPS: Remove dev_err() usage after platform_get_irq()
  MIPS: dts: mscc: describe the PTP ready interrupt
  MIPS: dts: mscc: describe the PTP register range
  ...
2019-09-22 09:30:30 -07:00
Jisheng Zhang 7548666e6f hwmon: Add Synaptics AS370 PVT sensor driver
Add a new driver for Synaptics AS370 PVT sensors. Currently, only
temperature is supported.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190827113259.4fb64a17@xhacker.debian
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Guenter Roeck 2c9d5b5e32 hwmon: Remove ads1015 driver
A driver for ADS1015 with more functionality is available in the iio
subsystem.

Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.

Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-03 12:47:17 -07:00
Paul Cercueil d202742058
hwmon: Drop obsolete JZ4740 driver
The JZ4740 boards now use the iio-hwmon driver.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
2019-07-30 10:41:54 -07:00
Lucas Tanure 4cdb562147 hwmon: lochnagar: Add Lochnagar 2 hardware monitoring driver
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform.

This driver adds support for the hardware monitoring features of
the Lochnagar 2 to the hwmon API. Monitoring is provided for
the board voltages, currents and temperature supported by the
board controller chip.

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-04-15 17:19:53 -07:00
Eddie James 5b5513b880 hwmon: Add On-Chip Controller (OCC) hwmon driver
The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.

This driver provides a hwmon interface to the OCC from a service
processor (e.g. a BMC). The driver supports both POWER8 and POWER9 OCCs.
Communications with the POWER8 OCC are established over standard I2C
bus. The driver communicates with the POWER9 OCC through the FSI-based
OCC driver, which handles the lower-level communication details.

This patch lays out the structure of the OCC hwmon driver. There are two
platform drivers, one each for P8 and P9 OCCs. These are probed through
the I2C tree and the FSI-based OCC driver, respectively. The patch also
defines the first common structures and methods between the two OCC
versions.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
[groeck: Fix up SPDX license identifier]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2018-12-16 15:13:05 -08:00
Linus Torvalds f3ea496213 ARM: SoC driver updates
Some of the larger changes this merge window:
  - Removal of drivers for Exynos5440, a Samsung SoC that never saw
    widespread use.
  - Uniphier support for USB3 and SPI reset handling
  - Syste control and SRAM drivers and bindings for Allwinner platforms
  - Qualcomm AOSS (Always-on subsystem) reset controller drivers
  - Raspberry Pi hwmon driver for voltage
  - Mediatek pwrap (pmic) support for MT6797 SoC
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlt+MMkPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3pB4QAIj7iVxSKEQFz65iXLTfMJKFZ9TSvRgWSDyE
 CHF+WOQGTnxkvySEHSw/SNqDM+Bas8ijR8b4vWzsXJFB+3HA0ZTGLU379/af1zCE
 9k8QjyIWtRWKX9fo7qCHVXlMfxGbOdbCOsh4jnmHqEIDxCHXpIiJRfvUbKIXGpfn
 tw6QpM70vm6Q6AdKwzmDbMCYnQAMWxBK/G/Q7BfRG+IYWYjFGbiWIc9BV9Ki8+nE
 3235ISaTHvAHodoec8tpLxv34GsOP4RCqscGYEuCf22RYfWva4S9e4yoWT8qPoIl
 IHWNsE3YWjksqpt9rj9Pie/PycthO4E4BUPMtqjMbC2OyKFgVsAcHrmToSdd+7ob
 t3VNM6RVl8xyWSRlm5ioev15CCOeWRi1nUT7m3UEBWpQ6ihJVpbjf1vVxZRW/E0t
 cgC+XzjSg26sWx1bSH9lGPFytOblAcZ04GG/Kpz02MmTgMiTdODFZ67AsqtdeQS7
 a9wpaQ+DgTqU0VcQx8Kdq8uy9MOztkhXn5yO8fEWjpm0lPcxjhJS4EpN+Ru2T7/Z
 AMuy5lRJfQzAPU9kY7TE0yZ07pgpZgh7LlWOoKtGD7UklzXVVZrVlpn7bApRN5vg
 ZLze5OiEiIF5gIiRC8sIyQ9TZdvg4NqwebCqspINixqs7iIpB7TG93WQcy82osSE
 TXhtx4Sy
 =ZjwY
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "Some of the larger changes this merge window:

   - Removal of drivers for Exynos5440, a Samsung SoC that never saw
     widespread use.

   - Uniphier support for USB3 and SPI reset handling

   - Syste control and SRAM drivers and bindings for Allwinner platforms

   - Qualcomm AOSS (Always-on subsystem) reset controller drivers

   - Raspberry Pi hwmon driver for voltage

   - Mediatek pwrap (pmic) support for MT6797 SoC"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
  drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
  soc: fsl: cleanup Kconfig menu
  soc: fsl: dpio: Convert DPIO documentation to .rst
  staging: fsl-mc: Remove remaining files
  staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
  staging: fsl-dpaa2: eth: move generic FD defines to DPIO
  soc: fsl: qe: gpio: Add qe_gpio_set_multiple
  usb: host: exynos: Remove support for Exynos5440
  clk: samsung: Remove support for Exynos5440
  soc: sunxi: Add the A13, A23 and H3 system control compatibles
  reset: uniphier: add reset control support for SPI
  cpufreq: exynos: Remove support for Exynos5440
  ata: ahci-platform: Remove support for Exynos5440
  soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
  soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
  soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
  soc: mediatek: pwrap: fix cipher init setting error
  dt-bindings: pwrap: mediatek: add pwrap support for MT6797
  reset: uniphier: add USB3 core reset control
  dt-bindings: reset: uniphier: add USB3 core reset support
  ...
2018-08-23 13:52:46 -07:00
Stefan Wahren 74d1e00791 hwmon: Add support for RPi voltage sensor
Currently there is no easy way to detect undervoltage conditions on a
remote Raspberry Pi. This hwmon driver retrieves the state of the
undervoltage sensor via mailbox interface. The handling based on
Noralf's modifications to the downstream firmware driver. In case of
an undervoltage condition only an entry is written to the kernel log.

CC: "Noralf Trønnes" <noralf@tronnes.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
2018-07-09 10:47:27 -07:00
Tomer Maimon f1fd4a4db7 hwmon: Add NPCM7xx PWM and Fan driver
Add Nuvoton BMC NPCM750/730/715/705 Pulse Width Modulation (PWM)
and Fan tacho driver.

The Nuvoton BMC NPCM750/730/715/705 supports 8 PWM controller outputs
and 16 Fan controller inputs.

The driver provides a sysfs entries through which the user can
configure the duty-cycle value from 0(off) and 255(full speed)
and read the fan tacho rpm value.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2018-07-08 20:08:13 -07:00
Vadim Pasternak 65afb4c8e7 hwmon: (mlxreg-fan) Add support for Mellanox FAN driver
Driver obtains PWM and tachometers registers location according to the
system configuration and creates FAN/PWM hwmon objects and a cooling
device. PWM and tachometers are controlled through the on-board
programmable device, which exports its register map. This device could be
attached to any bus type, for which register mapping is supported. Single
instance is created with one PWM control, up to 12 tachometers and one
cooling device. It could be as many instances as programmable device
supports.

Currently driver will be activated from the Mellanox platform driver:
drivers/platform/x86/mlx-platform.c.
For the future ARM based systems it could be activated from the ARM
platform module.

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2018-07-08 20:08:13 -07:00
Sudeep Holla b23688aefb hwmon: add support for sensors exported via ARM SCMI
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Management Interface
(SCMI). The supported sensor types is one of voltage, temperature,
current, and power.

The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.

Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2018-02-28 16:37:57 +00:00
Lei YU ee249f2715 hwmon: Add W83773G driver
Nuvoton W83773G is a hardware monitor IC providing one local
temperature and two remote temperature sensors.

Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2018-01-02 15:05:34 -08:00
Linus Torvalds 1e19bded7f hwmon updates for v4.15
- Drivers for MAX31785 and MAX6621
 - Support for AMD family 17h (Ryzen, Threadripper) temperature sensors
 - Various driver cleanups and minor improvements
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaCKuYAAoJEMsfJm/On5mBjVAP/A/gfAv5KGYsuzEm+Oph3UFq
 dQsuqEr7cUhBnhApwfotT9ygNWRfVknPyvCjTJanHXca1eAE+4srgXY3yRpo5s6R
 YlVbkT7fYRO+SrjXsWhKBcctzKjrkyiNYTz+BqGbzQ9Y6QStnkrQTweB1NOAkasy
 o7WsAlh9bX4966GyAq6OOQZ3dOwvKGVl8dovEJQk5ZtW0e0TOrGbPM5KZsXN+Haa
 adUAMBhxEzSH7SqO1UIlnn0DfF7Ikp291Vy03LZKnGDIN/myI602HrRerrnZhDw6
 Beq4YyYRjNVqwkkIwpAlElKAGK5QXhbuUb9ScvhEMZSf2e80t/NzLmDQrWVKevAy
 VSnFaP+cKIx9hYMwQe92fbn1dhASOf5z+LxzC8kyAloUHZ8ZGH6JEkPRFPCijoiV
 MQ+/YM1jpzzAqiW1HilxVouVjq0lhJwrnqozwbrF/HfyeIzBVd76o+4AIrOVFKLR
 zXtKbiLsFQz3GDRGzCp5CswQnyFMU0K5Hpx2iSd7UYx6OWH6Q5Hf6ieC8LJmst1d
 akbFSiExgF+CIZc5TYaFIBO740vpo8EXJesGIA6uZYoMxk8iConahMAkzJV5ik3Z
 H1LghVhkgYjccdJQ/dxfmQ87+P4bYeRp0KQPRHBAHTcUe0htqR006rcsDDBwznGx
 LwrUeeSMf+dS7dj+jSLV
 =NpxT
 -----END PGP SIGNATURE-----

Merge tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - drivers for MAX31785 and MAX6621

 - support for AMD family 17h (Ryzen, Threadripper) temperature sensors

 - various driver cleanups and minor improvements

* tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (30 commits)
  dt-bindings: pmbus: Add Maxim MAX31785 documentation
  pmbus: Add driver for Maxim MAX31785 Intelligent Fan Controller
  hwmon: (aspeed-pwm-tacho) Sort headers
  hwmon: (xgene) Minor clean up of ifdef and acpi_match_table reference
  hwmon: (max6621) Inverted if condition in max6621_read()
  hwmon: (asc7621) remove redundant assignment to newval
  hwmon: (xgene) Support hwmon v2
  hwmon: (gpio-fan) Fix null pointer dereference at probe
  hwmon: (gpio-fan) Convert to use GPIO descriptors
  hwmon: (gpio-fan) Rename GPIO line state variables
  hwmon: (gpio-fan) Get rid of the gpio alarm struct
  hwmon: (gpio-fan) Get rid of platform data struct
  hwmon: (gpio-fan) Mandate OF_GPIO and cut pdata path
  hwmon: (gpio-fan) Send around device pointer
  hwmon: (gpio-fan) Localize platform data
  hwmon: (gpio-fan) Use local variable pointers
  hwmon: (gpio-fan) Move DT bindings to the right place
  Documentation: devicetree: add max6621 device
  hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor
  hwmon: (w83793) make const array watchdog_minors static, reduces object code size
  ...
2017-11-13 08:55:46 -08:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Vadim Pasternak 92b64580f1 hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor
MAX6621 is a PECI-to-I2C translator provides an efficient, low-cost
solution for PECI-to-SMBus/I2C protocol conversion. It allows reading the
temperature from the PECI-compliant host directly from up to four
PECI-enabled CPUs.

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2017-10-29 18:36:03 -07:00
Florian Eckert 7074d0a927 hwmon: (ltq-cputemp) add cpu temp sensor driver
Add the lantiq cpu temperature sensor support for xrx200.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2017-09-01 07:24:14 -07:00
Sebastian Reichel 09d9d82745 hwmon: (twl4030-madc) drop driver
This driver is no longer needed:

 * It has no mainline users
 * It has no DT support and OMAP is DT only
 * iio-hwmon can be used for madc, which also works with DT

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2017-04-30 11:45:31 -07:00
Jaghathiswari Rankappagounder Natarajan 2d7a548a3e drivers: hwmon: Support for ASPEED PWM/Fan tach
The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports.
The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer
inputs.
The device driver matches on the device tree node. The configuration
values are read from the device tree and written to the respective
registers.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value (ranging from 0 to 100 percent) and read
the fan tach rpm value.

Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2017-04-10 13:12:18 -07:00
andrea.merello 7f07ec0fa1 hwmon: new driver for ST stts751 thermal sensor
This patch adds a HWMON driver for ST Microelectronics STTS751
temperature sensors.

Thanks-to: LABBE Corentin [for suggestions]
Thanks-to: Guenter Roeck [for suggestion and discussions]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Cc: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2017-02-03 05:32:59 -08:00
John Muir 66e1c91713 hwmon: Add Texas Instruments TMP108 temperature sensor driver.
Add support for the TI TMP108 temperature sensor with some device
configuration parameters.

Signed-off-by: John Muir <john@jmuir.com>
[groeck: Initialize of_match_table]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-12-09 21:54:25 -08:00
Chris Packham aaf6fabf1b hwmon: Add tc654 driver
Add support for the tc654 and tc655 fan controllers from Microchip.

http://ww1.microchip.com/downloads/en/DeviceDoc/20001734C.pdf

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed continuation line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-12-02 13:28:05 -08:00
hotran ed42cfa881 hwmon: Add xgene hwmon driver
This patch adds hardware temperature and power reading support for
APM X-Gene SoC using the mailbox communication interface.

Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-09-08 21:34:16 -07:00
Thilo Cestonaro 08426eda58 hwmon: Add driver for FTS BMC chip "Teutates"
This driver implements hardware monitoring and watchdog support
for the FTS BMC Chip "Teutates".

Signed-off-by: Thilo Cestonaro <thilo@cestona.ro>
[groeck: Updated subject and description; fixed dependencies]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-07-20 06:29:54 -07:00
Andrew F. Davis 7cb6dcff19 hwmon: Add support for INA3221 Triple Current/Voltage Monitors
Add support for the the INA3221 26v capable, Triple channel,
Bi-Directional, Zero-Drift, Low-/High-Side, Current/Voltage Monitor
with I2C interface.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-06-27 18:58:03 -07:00
David Frey 7c84f7f80d hwmon: add support for Sensirion SHT3x sensors
This driver implements support for the Sensirion SHT3x-DIS chip,
a humidity and temperature sensor. Temperature is measured
in degrees celsius, relative humidity is expressed as a percentage.
In the sysfs interface, all values are scaled by 1000,
i.e. the value for 31.5 degrees celsius is 31500.

Signed-off-by: Pascal Sachs <pascal.sachs@sensirion.com>
[groeck: Fixed 'Variable length array is used' gcc warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-06-27 18:58:03 -07:00
Tiberiu Breana 04e1e70afe hwmon: (max31722) Add support for MAX31722/MAX31723 temperature sensors
Add basic support for the Maxim Integrated MAX31722/MAX31723 SPI
temperature sensors / thermostats.

Includes:
    - ACPI support;
    - raw temperature readings;
    - power management

Datasheet:
https://datasheets.maximintegrated.com/en/ds/MAX31722-MAX31723.pdf

Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-04-19 06:32:34 -07:00
Adam Baker 630300d5fc hwmon: Create an NSA320 hardware monitoring driver
Create a driver to support the hardware monitoring chip present in
the Zyxel NSA320 and some of the other Zyxel NAS devices.

The driver reads fan speed and temperature from a suitably
pre-programmed MCU on the device.

Signed-off-by: Adam Baker <linux@baker-net.org.uk>
[groeck: Dropped .owner field initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-03-08 18:40:49 -08:00
Mike Looijmans df92270357 hwmon: Add LTC2990 sensor driver
This adds support for the Linear Technology LTC2990  I2C System Monitor.
The LTC2990 supports a combination of voltage, current and temperature
monitoring. This driver currently only supports reading two currents
by measuring two differential voltages across series resistors, in
addition to the Vcc supply voltage and internal temperature.

This is sufficient to support the Topic Miami SOM which uses this chip
to monitor the currents flowing into the FPGA and the CPU parts.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-03-05 06:25:34 -08:00
Sudeep Holla c32f5eff2d hwmon: (vexpress) rename vexpress hwmon implementation
The vexpress hwmon implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in regulators.

This patch renames the vexpress hwmon implementation to vexpress-hwmon
so that there will be no clash in the module namespace.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2016-03-05 06:25:33 -08:00
Guenter Roeck 2ff44072e3 hwmon: (htu21) Remove driver
HTU21 is now supported by IIO, and can be instantiated as hwmon driver
using the iio-hwmon bridge. An explicit hwmon driver is no longer needed.

Cc: William Markezana <william.markezana@meas-spec.com>
Cc: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2015-12-18 08:20:59 -08:00
Linus Torvalds b44a3d2a85 ARM: SoC driver updates for v4.4
As we've enabled multiplatform kernels on ARM, and greatly done away with
 the contents under arch/arm/mach-*, there's still need for SoC-related
 drivers to go somewhere.
 
 Many of them go in through other driver trees, but we still have
 drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
 that might be shared between ARM and ARM64 (or just in general makes
 sense to not have under the architecture directory).
 
 This branch contains mostly such code:
 
 - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
   with power management blocks on these SoCs for use by clock, regulator and
   bus frequency drivers.
 - Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
 - Drivers for ARM's SCPI (System Control Processor). Not to be confused with
   PSCI (Power State Coordination Interface). SCPI is used to communicate with
   the assistant embedded cores doing power management, and we have yet to see
   how many of them will implement this for their hardware vs abstracting in
   other ways (or not at all like in the past).
 - To make confusion between SCPI and PSCI more likely, this release also
   includes an update of PSCI to interface version 1.0.
 - Rockchip support for power domains.
 - A driver to talk to the firmware on Raspberry Pi.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJWQC+cAAoJEIwa5zzehBx3jEUP/0GpxfDVanEUkudVLLe7J0RH
 CNlRan107Cw6hXRUJo7elEsuCALjccXjc1CAH4+RnNpOAeBKW97n+WU7trTv+wUZ
 sQX4SkBPKFBlgwGF2qhsi5q74gms/BrgtCa4kNb9joOYso039tlfIOPzK80DMkOm
 TkyIJdUCgFJMjCQLhX6kGT0PDcrbIjb6aA2cF3FAVeaJA7uz8lNe/eHJr3oHxIEY
 CvC651yJ2mIHQUU4BJx/AJo+wXg3dRUXNCAtBjwLRPEAzduYZXYm1ZTVIby/1q9r
 dR2KDFEuibODXmXrDBzKNJwCu/TLJEwo/1oPaEIVfY91XLKfiWUhgVqa1o1I+d9U
 XoGPibCW461qFahjQW87MfInALpCOA7/RbTNjFp+MVyipCYvkaYq7KFiYEldgFDx
 z4Qx/J4hYc2TlDWrpNiUCZMfmhwi7y+Ib+tnenYTO1eyMuw0e9mfnVdjk5iU3Pvk
 Ye4qPqpYclJruyHbYi164878+1lLaW2NCUgC3rkBO/GWPAzp7d9iLWoZ3PuyD5i5
 PEjs668UcRdZYbI4rdrhGHL8Eq9Gnuc4Rthu7HxPOK+DG0XgP8r97PhM8aYGYVDO
 +yikBtjWRsA9fPj3rMKA3UsQ61DAeR9LmZ0XPGjWFMCjCG0JlUoIMaA+Uu0i8fr8
 95qxBVxbO7rhL39r1rhV
 =dm+I
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "As we've enabled multiplatform kernels on ARM, and greatly done away
  with the contents under arch/arm/mach-*, there's still need for
  SoC-related drivers to go somewhere.

  Many of them go in through other driver trees, but we still have
  drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
  that might be shared between ARM and ARM64 (or just in general makes
  sense to not have under the architecture directory).

  This branch contains mostly such code:

   - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
     communicate with power management blocks on these SoCs for use by
     clock, regulator and bus frequency drivers.

   - Allwinner Reduced Serial Bus driver, again used to communicate with
     PMICs.

   - Drivers for ARM's SCPI (System Control Processor).  Not to be
     confused with PSCI (Power State Coordination Interface).  SCPI is
     used to communicate with the assistant embedded cores doing power
     management, and we have yet to see how many of them will implement
     this for their hardware vs abstracting in other ways (or not at all
     like in the past).

   - To make confusion between SCPI and PSCI more likely, this release
     also includes an update of PSCI to interface version 1.0.

   - Rockchip support for power domains.

   - A driver to talk to the firmware on Raspberry Pi"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
  soc: qcom: smd-rpm: Correct size of outgoing message
  bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
  bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
  ARM: bcm2835: add mutual inclusion protection
  drivers: psci: make PSCI 1.0 functions initialization version dependent
  dt-bindings: Correct paths in Rockchip power domains binding document
  soc: rockchip: power-domain: don't try to print the clock name in error case
  soc: qcom/smem: add HWSPINLOCK dependency
  clk: berlin: add cpuclk
  ARM: berlin: dts: add CLKID_CPU for BG2Q
  ARM: bcm2835: Add the Raspberry Pi firmware driver
  soc: qcom: smem: Move RPM message ram out of smem DT node
  soc: qcom: smd-rpm: Correct the active vs sleep state flagging
  soc: qcom: smd: delete unneeded of_node_put
  firmware: qcom-scm: build for correct architecture level
  soc: qcom: smd: Correct SMEM items for upper channels
  qcom-scm: add missing prototype for qcom_scm_is_available()
  qcom-scm: fix endianess issue in __qcom_scm_is_call_available
  soc: qcom: smd: Reject send of too big packets
  soc: qcom: smd: Handle big endian CPUs
  ...
2015-11-10 15:00:03 -08:00
Il Han 195a4b4298 hwmon: Driver for Maxim MAX31790
The driver supports the Maxim MAX31790.

Signed-off-by: Il Han <corone.il.han@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2015-10-14 07:57:14 -07:00
Punit Agrawal ea98b29a05 hwmon: Support sensors exported via ARM SCP interface
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.

The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.

Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
2015-10-09 11:05:52 +01:00
Linus Torvalds d87823813f Char/Misc driver patches for 4.2-rc1
Here's the big char/misc driver pull request for 4.2-rc1.
 
 Lots of mei, extcon, coresight, uio, mic, and other driver updates in
 here.  Full details in the shortlog.  All of these have been in
 linux-next for some time with no reported problems.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlWNn0gACgkQMUfUDdst+ykCCQCgvdF4F2+Hy9+RATdk22ak1uq1
 JDMAoJTf4oyaIEdaiOKfEIWg9MasS42B
 =H5wD
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver updates from Greg KH:
 "Here's the big char/misc driver pull request for 4.2-rc1.

  Lots of mei, extcon, coresight, uio, mic, and other driver updates in
  here.  Full details in the shortlog.  All of these have been in
  linux-next for some time with no reported problems"

* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
  mei: me: wait for power gating exit confirmation
  mei: reset flow control on the last client disconnection
  MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
  misc: sram: sort and clean up included headers
  misc: sram: move reserved block logic out of probe function
  misc: sram: add private struct device and virt_base members
  misc: sram: report correct SRAM pool size
  misc: sram: bump error message level on unclean driver unbinding
  misc: sram: fix device node reference leak on error
  misc: sram: fix enabled clock leak on error path
  misc: mic: Fix reported static checker warning
  misc: mic: Fix randconfig build error by including errno.h
  uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
  uio: pruss: Add CONFIG_HAS_IOMEM dependence
  uio: pruss: Include <linux/sizes.h>
  extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
  char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
  Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
  parport: check exclusive access before register
  w1: use correct lock on error in w1_seq_show()
  ...
2015-06-26 14:51:15 -07:00
Maciej S. Szmigiero 761c1770f2 hwmon: add driver for Microchip TC74
Add hwmon driver for the Microchip TC74.

The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.

Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2015-06-21 22:54:53 -07:00
Pali Rohár 039ae58503 hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k
This patch splits CONFIG_I8K compile option to SENSORS_DELL_SMM and CONFIG_I8K.
Option SENSORS_DELL_SMM is now used to enable compilation of dell-smm-hwmon
driver and old CONFIG_I8K option to enable /proc/i8k interface in driver.

So this change allows to compile dell-smm-hwmon driver without legacy /proc/i8k
interface which is needed only for old Dell Inspirion models or for userspace
i8kutils package.

For backward compatibility when CONFIG_I8K is enabled then also SENSORS_DELL_SMM
is enabled and so driver dell-smm-hwmon (with /proc/i8k) is compiled.

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:48:12 -07:00
Pali Rohár a5afba16c6 hwmon: Rename i8k driver to dell-smm-hwmon and move it to hwmon tree
This commit moves i8k driver to hwmon tree under name dell-smm-hwmon which is
better name then abbreviation i8k. For backward compatibility is added macro
MODULE_ALIAS("i8k") so modprobe will load driver also old name i8k. CONFIG_I8K
compile option was not changed.

This commit also adds me as maintainer of this new dell-smm-hwmon driver and
remove Guenter Roeck from list who is implicit maintainer all hwmon drivers.

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:48:12 -07:00
Vadim V. Vlasov 9c947d25c9 hwmon: Add Nuvoton NCT7904 hwmon driver
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.

Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2015-03-09 09:59:36 -07:00
Jean Delvare ada072816b hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
The Intel 5500, 5520 and X58 chipsets embed a digital thermal sensor.
This new driver supports it.

Note that on many boards the sensor seems to be disabled and reports
the minimum value (36.5 degrees Celsius) all the time.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
2015-01-24 14:16:21 +01:00
Guenter Roeck 3434f37835 hwmon: Driver for Nuvoton NCT7802Y
NCT7802Y is an I2C based hardware monitoring chip from Nuvoton.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-30 20:13:13 -08:00