Current OMAP3 I2C driver code does not follow the correct sequence for soft
reset. Due to this, lock up issues are reported during timeout/error cases.
This patch fixes above issue by disabling I2C controller as per OMAP3430 TRM
for soft reset. As per TRM, I2C controller needs to be disabled as a first
step during soft reset.
Here is correct soft reset sequence:
a. Ensure that the module is disabled
(clear the I2Ci.I2C_CON[15] I2C_EN bit to 0).
b. Set the I2Ci.I2C_SYSC[1] SRST bit to 1.
c. Enable the module by setting I2Ci.I2C_CON[15] I2C_EN bit to 1.
d. Check the I2Ci.I2C_SYSS[0] RDONE bit until it is set to 1 to
indicate the software reset is complete.
Tested on Zoom2, Zoom3, 3430SDP and 3630SDP
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: George, Harith<harith@ti.com>
Acked-by: Varadarajan, Charu Latha<charu@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit ef871432... (i2c-omap: OMAP3: PM: (re)init for every transfer
to support off-mode) introduced a change which make the dev->iestate
contents be written to the OMAP_I2C_IE_REG every time omap_i2c_unidle
is called. Previously, the state was only written if it wasn't equal
to zero.
In omap_i2c_probe, omap_i2c_unidle() is called prior to omap_i2c_init(),
in which case dev->iestate has not yet been initialized and will be set
to zero. Having this value written to the registers causes deadlock
while booting.
As such, this change restores the original functionality.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Calculation of the CLKDIV speed setting should be done using base 10 math
rather than base 2. We also avoid exceeding the spec due to integer
truncation and a 50% duty cycle.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] use resource_size()
[WATCHDOG] iTCO_wdt: add PCI ID for the Intel EP80579 (Tolapai) SoC
This reverts commit 9f15226e75. It's just
wrong, and broke resume for Rafael even on a non-AMD CPU.
As Rafael says:
"... it causes microcode_init_cpu() to be called during resume even for
CPUs for which there's no microcode to apply. That, in turn, results
in executing request_firmware() (on Intel CPUs at least) which doesn't
work at this stage of resume (we have device interrupts disabled, I/O
devices are still suspended and so on).
If I'm not mistaken, the "if (uci->valid)" logic means "if that CPU is
known to us" , so before commit 9f15226e75 microcode_resume_cpu() was
called for all CPUs already in the system during suspend, which was
the right thing to do. The commit changed it so that the CPUs without
microcode to apply are now treated as "unknown", which is not quite
right.
The problem this commit attempted to solve has to be handled
differently."
Bisected-and -requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Executing _OSC returns a buffer, which has an acpi object in it.
Don't directly returns the buffer, instead, we return the acpi object's
buffer. This fixes a regression since caller of acpi_run_osc expects
an acpi object's buffer returned.
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Fix a bug on appledisplay.c regarding signedness
USB: option: support hi speed for modem Haier CE100
USB: audio gadget: free alsa devices when unloading
USB: audio gadget: fix wTotalLength calculation
usb: otg: isp1301_omap: fix compile error
USB: musb: workaround Blackfin FIFO anomalies
USB: musb: Fix array index out of bounds issue
USB: musb: Fix null pointer dereference issue
USB: musb: correct DMA address for tx
USB: musb: gadget_ep0: avoid SetupEnd interrupt
USB: musb: fix for crash in DM646x USB when (CPPI)DMA is enabled
USB: musb: do not work if no gadget driver is loaded
USB: musb: gadget: set otg tranceiver to idle when registering gadget
USB: musb: Populate the VBUS GPIO with the correct GPIO number
USB: musb: MAINTAINERS: Fix my tree's address
USB: musb: fix compiling warning with min() macro
USB: musb: move musb_remove to __exit
USB: musb_gadget: fix kernel oops in txstate()
USB: ftdi_sio: sort PID/VID entries in new ftdi_sio_ids.h header
USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h header
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
devtmpfs: unlock mutex in case of string allocation error
Driver core: export platform_device_register_data as a GPL symbol
driver core: Prevent reference to freed memory on error path
Driver-core: Fix bogus 0 error return in device_add()
Driver core: driver_attribute parameters can often be const*
Driver core: bin_attribute parameters can often be const*
Driver core: device_attribute parameters can often be const*
Doc/stable rules: add new cherry-pick logic
vfs: get_sb_single() - do not pass options twice
devtmpfs: Convert dirlock to a mutex
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging/vt66*: kconfig, depends on WLAN
Staging: batman-adv: introduce missing kfree
Staging: batman-adv: Add Kconfig dependancies on PROC_FS and PACKET.
Staging: panel: Adjust range for PANEL_KEYPAD in Kconfig
Staging: panel: Fix compilation error with custom lcd charset
Staging: ramzswap: remove ARM specific d-cache hack
Staging: rtl8192x: fix printk formats
Staging: wlan-ng: fix Correct size given to memset
staging: rtl8192su: add USB VID/PID for HWNUm-300
staging: fix rtl8192su compilation errors with mac80211
staging: fix rtl8192e compilation errors with mac80211
Staging: fix rtl8187se compilation errors with mac80211
Staging: rtl8192su: fix test for negative error in rtl8192_rx_isr()
Staging: comedi: jr3_pci: Don't ioremap too much space. Check result.
Staging: comedi: removed "depricated" from COMEDI_CB_BLOCK
Staging: comedi: usbdux.c: fix locking up of the driver when the comedi ringbuffer runs empty
Staging: dst: remove from the tree
Staging: sm7xx: add a new framebuffer driver
Staging: batman: fix debug Kconfig option
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Set i_nlink properly during reflink.
ocfs2: Add reflinked file's inode to inode hash eariler.
ocfs2: refcounttree.c cleanup.
ocfs2: Find proper end cpos for a leaf refcount block.
The zone list code clearly cannot tolerate concurrent writers (I couldn't
find any locks for that), so simply add a global mutex. No need for RCU
in this case.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
When printing legacy sysctls print the warning message
for each of them only once. This way there is a guarantee
the syslog won't be flooded for any sane program.
The original attempt at this made the tables non const and stored
the flag inline.
Linus suggested using a separate hash table for this, this is based on a
code snippet from him.
The hash implies this is not exact and can sometimes not print a
new sysctl due to a hash collision, but in practice this should not
be a problem
I used a FNV32 hash over the binary string with a 32byte bitmap. This
gives relatively little collisions when all the predefined binary sysctls
are hashed:
size 256
bucket
length number
0: [25]
1: [67]
2: [88]
3: [47]
4: [22]
5: [6]
6: [1]
The worst case is a single collision of 6 hash values.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
It is unpredictable to have the same memory mapped using different
shared bit settings for ARMv6 and ARMv7 CPUs. Fix this for the CPU
write buffer bug test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Kevin Hilman <khilman@ti.deeprootsystems.com>
Cc: Ulrik Bech Hald <ubh@ti.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.
Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.
Fixed that. Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: pancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wTotalLength should contain the sum of the interface and unit
descriptor sizes per the Audio Device Class specification 1.0.
Reported-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 91c8a5a998 broke
compilation of this driver after it introduced
otg_init() as a static inline in <linux/usb/otg.h>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of these workarounds are already in place, but labeled as affecting
all BF52x parts. Since we have official anomaly numbers now, use those
defines. And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below array index out of bounds issue.
Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84
The data stored in 'aInfo' array exceeds the array size of 78.
This patch increases the size of this array to hold the string
correctly without any memory corruption.
This issue was reported by Klockwork tool.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following NULL pointer dereference issue.
Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.
============
Code Snippet
============
748: request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
csr &= ~(MUSB_RXCSR_AUTOCLEAR
| MUSB_RXCSR_DMAENAB
| MUSB_RXCSR_DMAMODE);
musb_writew(epio, MUSB_RXCSR,
MUSB_RXCSR_P_WZC_BITS | csr);
792: request->actual += musb_ep->dma->actual_len;
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadget stalling a zero-length SETUP request results in this error message:
SetupEnd came in a wrong ep0stage idle
In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request. Add the missing '\n' to the error message itself as well...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO. Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.
Update over previous patch to avoid taking the lock if already
taken. Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.
Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a null-pointer dereference bug.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
pointer types lacks a cast
So switch to min_t(size_t, ...).
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
probe() already was on __init, so moving remove() to __exit.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 7723de7e19 (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a (almost) sort-only patch to sort FTDI device
product ID definitions in new ftdi_sio_ids.h header.
Advantage is that new device ID submissions will now have a specific (sorted)
position - less future merge conflicts.
Compile-tested, based on _current_ mainline git.
Minor checkpatch.pl warnings were eliminated whereever it made sense,
very minor text changes.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).
Compile-tested, based on latest mainline git.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix new kernel-doc warnings in usb core:
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'config'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'iface_num'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'alt_num'
Warning(drivers/usb/core/hcd.c:1622): No description found for parameter 'udev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 917778267f removed __init from
ehci_wait_for_port(), but left it in place on ehci_reset_port(), which
is being called from the former function.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While converting emi62 to use request_firmware(), the driver was also
changed to use the ihex helper functions. However, this broke the loading
of the FPGA firmware because the code tries to access the addr field of
the EOF record which works with a plain array that has an empty last
record but not with the ihex helper functions where the end of the data is
signaled with a NULL record pointer, resulting in:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f80d248c>] emi62_load_firmware+0x33c/0x740 [emi62]
This can be fixed by changing the loop condition to test the return value
of ihex_next_binrec() directly (like in emi26.c).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Der Mickster <retroeffective@gmail.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects a problem where drivers/usb/otg is linked twice
if CONFIG_USB_ULPI is selected, resulting in a build error (symbol
conflict). The files in that directory are properly linked already
as part of CONFIG_USB, and need not be indicated specifically for
CONFIG_USB_ULPI.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use ERR_PTR and IS_ERR rather than mixing integers and pointers.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *E;
@@
* E < 0
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1315) fixes some bugs in the USB core authorization
code:
usb_deauthorize_device() should deallocate the device strings
instead of leaking them, and it should invoke
usb_destroy_configuration() (which does proper reference
counting) instead of freeing the config information directly.
usb_authorize_device() shouldn't change the device strings
until it knows that the authorization will succeed, and it should
autosuspend the device at the end (having autoresumed the
device at the start).
Because the device strings can be changed, the sysfs routines
to display the strings must protect the string pointers by
locking the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Acked-by: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1314) renames usb_configure_device() and
usb_configure_device_otg() in the hub driver. Neither name is
appropriate because these routines enumerate devices, they don't
configure them. That's handled by usb_choose_configuration() and
usb_set_configuration().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1313) updates the documentation concerning USB power
management.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vt665[56] drivers can be built when CONFIG_NET=n &
CONFIG_NETDEVICES=n or just when CONFIG_WLAN=n.
This leads to build failures.
Prevent this by making them depend on WLAN.
[This patch was lost in a dualing trees merge;
still needs to be re-applied.]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Error handling code following a kzalloc should free the allocated data.
Similarly for usb-alloc urb.
The semantic match that finds the first problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In panel.c there are only the values 0-3 defined. So 4 is invalid:
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When compiling panel.c with a DEFAULT_LCD_CHARSET it fails to compile
with the following error message:
drivers/staging/panel/panel.c: In function >>lcd_init<<:
drivers/staging/panel/panel.c:1396: error: expected expression before
>>;<< token
drivers/staging/panel/panel.c:1475: error: expected expression before
>>;<< token
make[3]: *** [drivers/staging/panel/panel.o] error 1
make[2]: *** [drivers/staging/panel] error 2
make[1]: *** [drivers/staging] error 2
The config used was:
CONFIG_PANEL=m
CONFIG_PANEL_PARPORT=0
CONFIG_PANEL_PROFILE=0
CONFIG_PANEL_KEYPAD=0
CONFIG_PANEL_LCD=1
CONFIG_PANEL_LCD_HEIGHT=2
CONFIG_PANEL_LCD_WIDTH=20
CONFIG_PANEL_LCD_BWIDTH=40
CONFIG_PANEL_LCD_HWIDTH=64
CONFIG_PANEL_LCD_CHARSET=0
CONFIG_PANEL_LCD_PROTO=0
CONFIG_PANEL_LCD_PIN_E=14
CONFIG_PANEL_LCD_PIN_RS=17
CONFIG_PANEL_LCD_PIN_RW=16
CONFIG_PANEL_LCD_PIN_BL=0
This patch fixes both errors, as it fixes the define
Patch against current linux-next tree at Tue Dec 15 06:07:01 2009 +0100
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
