Commit Graph

2 Commits

Author SHA1 Message Date
Si-Wei Liu 8065a779f1 failover: allow name change on IFF_UP slave interfaces
When a netdev appears through hot plug then gets enslaved by a failover
master that is already up and running, the slave will be opened
right away after getting enslaved. Today there's a race that userspace
(udev) may fail to rename the slave if the kernel (net_failover)
opens the slave earlier than when the userspace rename happens.
Unlike bond or team, the primary slave of failover can't be renamed by
userspace ahead of time, since the kernel initiated auto-enslavement is
unable to, or rather, is never meant to be synchronized with the rename
request from userspace.

As the failover slave interfaces are not designed to be operated
directly by userspace apps: IP configuration, filter rules with
regard to network traffic passing and etc., should all be done on master
interface. In general, userspace apps only care about the
name of master interface, while slave names are less important as long
as admin users can see reliable names that may carry
other information describing the netdev. For e.g., they can infer that
"ens3nsby" is a standby slave of "ens3", while for a
name like "eth0" they can't tell which master it belongs to.

Historically the name of IFF_UP interface can't be changed because
there might be admin script or management software that is already
relying on such behavior and assumes that the slave name can't be
changed once UP. But failover is special: with the in-kernel
auto-enslavement mechanism, the userspace expectation for device
enumeration and bring-up order is already broken. Previously initramfs
and various userspace config tools were modified to bypass failover
slaves because of auto-enslavement and duplicate MAC address. Similarly,
in case that users care about seeing reliable slave name, the new type
of failover slaves needs to be taken care of specifically in userspace
anyway.

It's less risky to lift up the rename restriction on failover slave
which is already UP. Although it's possible this change may potentially
break userspace component (most likely configuration scripts or
management software) that assumes slave name can't be changed while
UP, it's relatively a limited and controllable set among all userspace
components, which can be fixed specifically to listen for the rename
events on failover slaves. Userspace component interacting with slaves
is expected to be changed to operate on failover master interface
instead, as the failover slave is dynamic in nature which may come and
go at any point.  The goal is to make the role of failover slaves less
relevant, and userspace components should only deal with failover master
in the long run.

Fixes: 30c8bd5aa8 ("net: Introduce generic failover module")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-10 22:12:26 -07:00
Sridhar Samudrala 30c8bd5aa8 net: Introduce generic failover module
The failover module provides a generic interface for paravirtual drivers
to register a netdev and a set of ops with a failover instance. The ops
are used as event handlers that get called to handle netdev register/
unregister/link change/name change events on slave pci ethernet devices
with the same mac address as the failover netdev.

This enables paravirtual drivers to use a VF as an accelerated low latency
datapath. It also allows migration of VMs with direct attached VFs by
failing over to the paravirtual datapath when the VF is unplugged.

Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-28 22:59:54 -04:00