This patch fixes a bug in the image seq. number handling in the
scanning level. The assignment of the image_seq was incorrect.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Do not forget to initialize 'gluebi->ubi_num' because otherwise
it will stay 0 even for ubi1 device, and gluebi will open
wrong UBI device when 'gluebi_get_device()' is called.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The recent "UBI: fix NOR flash recovery" introduced compilation
warnings which were immediately spotted by our linux-next keeper.
This patch fixes them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This commit fixes NOR flash recovery issues observed with Spansion
S29GL512N NOR.
When NOR erases, it first fills PEBs with zeroes, then sets all bytes
to 0xFF. Filling with zeroes starts from the end of the PEB. And when
power is cut, this results in PEBs containing correct EC and VID headers
but corrupted with zeros at the end. This confuses UBI and it mistakinly
accepts these PEBs and associate them with LEBs.
Fis this issue by zeroing EC and VID magics before erasing PEBs, to
make UBI later refuse zem.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Move the image seq. number handling from I/O level to the scanning
lever, where it really belongs to. Move the @image_seq_set variable
to the @struct ubi_scan_info structure, which exists only during
scanning.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
An image sequence number is added to the UBI erase-counter header
to be able determine if the root file system contains a mixture
of old and new images (because the flashing failed to complete).
A change to nolo is also needed for this to take effect.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'paranoid_check_empty()' is bogus because, which is easilly
seen on NOR flash, which has long erase cycles, and which may
easilly end-up with half-erased eraseblocks. In this case the
paranoid check fails. I is just wrong to assume that PEBs which
do not have EC headers always contain all 0xFF. Such assumption
should not be made on the I/O level, which is quite low.
Thus, just kill the check.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds code which makes sure eraseblocks contain all 0xFF
bytes before starting using them. The verification is done only when
debugging checks are enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Terminate the UBI background thread prior to restarting the system.
[Artem: amended comments a little]
Signed-off-by: Kevin Cernekee <kpc.mtd@gmail.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The UBIFS WL worker may encounter read errors and there is logic
which makes a decision whether we should do one of:
1. cancel the operation and move the PEB with the read errors to
the 'erroneous' list;
2. switch to R/O mode.
ATM, only -EIO errors trigger 1., other errors trigger 2. The idea
is that if we know we encountered an I/O error, do 1. Otherwise,
we do not know how to react, and do 2., just in case. E.g., if
the underlying driver became crazy because of a bug, we do not
want to harm any data, and switch to R/O mode.
This patch does 2 things:
1. Makes sure reads from the source PEB always cause 1. This is
more consistent with other reads which come from the upper
layers and never cause R/O.
2. Teaches UBI to do 1. also on -EBADMSG, UBI_IO_BAD_VID_HDR,
-ENOMEM, and -ETIMEOUT. But this is only when reading the
target PEB.
This preblems were hunted by Adrian Hunter.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
'kmem_cache_free()' oopeses if NULL is passed, and there is
one error-path place where UBI may call it with NULL object.
This problem was pointed to by Adrian Hunter.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When marking a PEB as bad, print how many PEBs are left reserved.
This is very useful information.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Print not only the PEB number, but also the LEB number and volume id,
which is very useful for bug hunting.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
[Artem: re-worked the patch: made it release resources when the
module is unloaded, made it do module referencing, made it really
independent on UBI, tested it with the UBI test-suite which can
be found in ubi-2.6.git/tests/ubi-tests, re-named most of the
funcs/variables to get rid of the "ubi" word and make names
consistent.]
Signed-off-by: Dmitry Pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove built-in gluebi support. This is a preparation for a
standalone glubi module support
Signed-off-by: Dmitry Pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI volume notifications are intended to create the API to get clients
notified about volume creation/deletion, renaming and re-sizing. A
client can subscribe to these notifications using 'ubi_volume_register()'
and cancel the subscription using 'ubi_volume_unregister()'. When UBI
volumes change, a blocking notifier is called. Clients also can request
"added" events on all volumes that existed before client subscribed
to the notifications.
If we use notifications instead of calling functions like 'ubi_gluebi_xxx()',
we can make the MTD emulation layer to be more flexible: build it as a
separate module and load/unload it on demand.
[Artem: many cleanups, rework locking, add "updated" event, provide
device/volume info in notifiers]
Signed-off-by: Dmitry Pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch improves UBI errors handling. ATM UBI switches to
R/O mode when the WL worker fails to read the source PEB.
This means that the upper layers (e.g., UBIFS) has no
chances to unmap the erroneous PEB and fix the error.
This patch changes this behaviour and makes UBI put PEBs
like this into a separate RB-tree, thus preventing the
WL worker from hitting the same read errors again and
again.
But there is a 10% limit on a maximum amount of PEBs like this.
If there are too much of them, UBI switches to R/O mode.
Additionally, this patch teaches UBI not to panic and
switch to R/O mode if after a PEB has been copied, the
target LEB cannot be read back. Instead, now UBI cancels
the operation and schedules the target PEB for torturing.
The error paths has been tested by ingecting errors
into 'ubi_eba_copy_leb()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes the error path in the WL worker - in same cases
UBI oopses when 'goto out_error' happens and e1 or e2 are NULL.
This patch also cleans up the error paths a little. And I have
tested nearly all error paths in the WL worker.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch is a clean-up and a preparation for the following
patches. It introduece constants for the return values of the
'ubi_eba_copy_leb()' function.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes a minor problem where we may fail to wake
upe the UBI background thread. This is not fatal at all,
it may just result at sligtly worse performace for a short
period of time, just because the thread will be woken up
when real I/O on the UBI starts.
Anywey, the issue is the race condition between
'ubi_attach_mtd_dev()' and 'ubi_thread()'. If we do not
serialize them, the 'wake_up_process()' call may be done
before 'ubi_thread()' went seep, but after it checked
'ubi->thread_enabled'.
This issue was spotted by Shin Hong <hongshin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The @vol->upd_marker should be protected by the @ubi->device_mutex,
otherwise 'paranoid_check_volume()' complains sometimes because
vol->upd_marker is 1 while vtbl_rec->upd_marker is 0.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If a volume paranoid check fails, do not return an error
code to the caller, but just print error messages and go
forward. The primary reason for this is that it is difficult
to recover and cancel the operation at that stage.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I am experiencing an error in 'paranoid_check_volume()'. Add
dump_stack() there to make it easier to identify the reasons
of the error.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When paranoid checs are enabled, the 'io_paral' test from the
'mtd-utils' package fails. The symptoms are:
UBI error: paranoid_check_all_ff: flash region at PEB 3973:512, length 15872 does not contain all 0xFF bytes
UBI error: paranoid_check_all_ff: paranoid check failed for PEB 3973
UBI: hex dump of the 512-16384 region
It turned out to be a bug in the checking function. Suppose there
are 2 tasks - A and B. Task A is the wear-levelling working
('wear_leveling_worker()'). It is reading the VID header to find
which LEB this PEB belongs to. Say, task A is reading header
of PEB X. Suppose PEB X is unmapped, and has no VID header.
Task B is trying to write to PEB X.
Task A: in 'ubi_io_read_vid_hdr()': reads the VID header from PEB X.
The read data contain all 0xFF bytes.
Task B: writes VID header and some data to PEB X
Task A: assumes PEB X is empty, calls 'paranoid_check_all_ff()', which
fails.
The solution for this problem is to make 'paranoid_check_all_ff()'
re-read the VID header, re-check it, and only if it is not there,
check the rest. This now implemented by the 'paranoid_check_empty()'
function.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The @ubi->dbg_peb_buf is needed only when paranoid checks are
enabled, not when debugging in general is enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Various minor improvements to the debugging messages which
I found useful while hunting problems.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The mutex essencially protects the entire UBI device, so the
old @volumes_mutex name is a little misleading.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The @mult_mutex does not serve any purpose. We already have
@volumes_mutex and it is enough. The @volume mutex is pushed
down to the 'ubi_rename_volumes()', because we want first
to open all volumes in the exclusive mode, and then lock the
mutex, just like all other ioctl's (remove, re-size, etc) do.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Now, we can call fsync() on an UBI volume.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Introduce a new ioctl UBI_IOCSETPROP to set properties
on a volume. Also add the first property:
UBI_PROP_DIRECT_WRITE, this property is used to set the
ability to use direct writes in userspace
Signed-off-by: Sidney Amani <seed@uffs.org>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
GregKH asked to fix UBI which has fake device release method. Indeed,
we have to free UBI device description object from the release method,
because otherwise we'll oops is someone opens a UBI device sysfs file,
then the device is removed, and he reads the file. With this fix, he
will get -ENODEV instead of an oops.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBI ioctl's do not work when running 64-bit kernel and 32-bit
user-land. Fix this by adding the compat_ioctl method.
Also, UBI serializes all ioctls, so more than one ioctl at a time
is not a problem. Amd UBI does not seem to depend on anything else,
so use unlocked_ioctl instead of ioctl (no BKL needed).
Reported-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Some ioctl's in UBI are enabled only when debugging is switched
on. There is not particular reason for this, just noone needed
them. However, some people need the now for their user-space
development. Thus, allow these ioctl's even if UBI debugging
is disabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl to check if an LEB is mapped or not (as a
debugging option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl for the LEB unmap operation (as a debugging
option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl for the LEB map operation (as a debugging
option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* git://git.infradead.org/mtd-2.6: (67 commits)
[MTD] [MAPS] Fix printk format warning in nettel.c
[MTD] [NAND] add cmdline parsing (mtdparts=) support to cafe_nand
[MTD] CFI: remove major/minor version check for command set 0x0002
[MTD] [NAND] ndfc driver
[MTD] [TESTS] Fix some size_t printk format warnings
[MTD] LPDDR Makefile and KConfig
[MTD] LPDDR extended physmap driver to support LPDDR flash
[MTD] LPDDR added new pfow_base parameter
[MTD] LPDDR Command set driver
[MTD] LPDDR PFOW definition
[MTD] LPDDR QINFO records definitions
[MTD] LPDDR qinfo probing.
[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately
[MTD] [NAND] pxa3xx: fix non-page-aligned reads
[MTD] [NAND] fix nandsim sched.h references
[MTD] [NAND] alauda: use USB API functions rather than constants
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] fix m25p80 64-bit divisions
[MTD] fix dataflash 64-bit divisions
[MTD] [NAND] Set the fsl elbc ECCM according the settings in bootloader.
...
Fixed up trivial debug conflicts in drivers/mtd/devices/{m25p80.c,mtd_dataflash.c}
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
UBI has 2 RB-trees to implement PEB protection, which is too
much for simply prevent PEB from being moved for some time.
This patch implements this using lists. The benefits:
1. No need to allocate protection entry on each PEB get.
2. No need to maintain balanced trees and walk them.
Signed-off-by: Xiaochuan-Xu <xiaochuan-xu@cqu.edu.cn>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
