Commit Graph

1925 Commits

Author SHA1 Message Date
NeilBrown 674806d62f md/raid5: More careful check for "has array failed".
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.

In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.

So encode this subtlety in a new function and call it as appropriate.

The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:

  good good good good incomplete good good failed failed

while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.

Reported-by: Terry Morris <tbmorris@tbmorris.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:35:27 +10:00
NeilBrown 70fffd0bfa md: Don't update ->recovery_offset when reshaping an array to fewer devices.
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.

If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.

Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.

This becomes relevant in the following sample scenario:

A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses.  The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.

If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:35:18 +10:00
NeilBrown e4e11e385d md/raid5: avoid oops when number of devices is reduced then increased.
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant.  Otherwise if we enlarge the array again,
we will reference uninitialised values.

As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:35:02 +10:00
Maciej Trela 049d6c1ef9 md: enable raid4->raid0 takeover
Only level 5 with layout=PARITY_N can be taken over to raid0 now.
Lets allow level 4 either.

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:34:57 +10:00
Maciej Trela 001048a318 md: clear layout after ->raid0 takeover
After takeover from raid5/10 -> raid0 mddev->layout is not cleared.

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:34:45 +10:00
Maciej Trela f73ea87375 md: fix raid10 takeover: use new_layout for setup_conf
Use mddev->new_layout in setup_conf.
Also use new_chunk, and don't set ->degraded in takeover().  That
gets set in run()

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:33:51 +10:00
NeilBrown e93f68a1fc md: fix handling of array level takeover that re-arranges devices.
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).

This renumbering is currently being done in the ->run method when the
new personality takes over.  However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.

Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.

So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.

Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:33:24 +10:00
Prasanna S. Panchamukhi 0544a21db0 md: raid10: Fix null pointer dereference in fix_read_error()
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().

Cc: stable@kernel.org
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Rob Becker <rbecker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:31:03 +10:00
NeilBrown f3b99be19d Restore partition detection of newly created md arrays.
Commit  b821eaa572 broke partition
detection for md arrays.

The logic was almost right.  However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.

So when md_open is called we still need to ensure that
->bd_invalidated gets set.  This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change.  At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.

Tested-by: Duncan <1i5t5.duncan@cox.net>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-06-24 13:31:03 +10:00
Akinobu Mita 55af6bb509 md: convert cpu notifier to return encapsulate errno value
By the previous modification, the cpu notifier can return encapsulate
errno value.  This converts the cpu notifiers for raid5.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-27 09:12:48 -07:00
Linus Torvalds e8bebe2f71 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (69 commits)
  fix handling of offsets in cris eeprom.c, get rid of fake on-stack files
  get rid of home-grown mutex in cris eeprom.c
  switch ecryptfs_write() to struct inode *, kill on-stack fake files
  switch ecryptfs_get_locked_page() to struct inode *
  simplify access to ecryptfs inodes in ->readpage() and friends
  AFS: Don't put struct file on the stack
  Ban ecryptfs over ecryptfs
  logfs: replace inode uid,gid,mode initialization with helper function
  ufs: replace inode uid,gid,mode initialization with helper function
  udf: replace inode uid,gid,mode init with helper
  ubifs: replace inode uid,gid,mode initialization with helper function
  sysv: replace inode uid,gid,mode initialization with helper function
  reiserfs: replace inode uid,gid,mode initialization with helper function
  ramfs: replace inode uid,gid,mode initialization with helper function
  omfs: replace inode uid,gid,mode initialization with helper function
  bfs: replace inode uid,gid,mode initialization with helper function
  ocfs2: replace inode uid,gid,mode initialization with helper function
  nilfs2: replace inode uid,gid,mode initialization with helper function
  minix: replace inode uid,gid,mode init with helper
  ext4: replace inode uid,gid,mode init with helper
  ...

Trivial conflict in fs/fs-writeback.c (mark bitfields unsigned)
2010-05-21 19:37:45 -07:00
NeilBrown 19fdb9eefb Merge commit '3ff195b011d7decf501a4d55aeed312731094796' into for-linus
Conflicts:
	drivers/md/md.c

- Resolved conflict in md_update_sb
- Added extra 'NULL' arg to new instance of sysfs_get_dirent.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-22 08:31:36 +10:00
Christoph Hellwig 8018ab0574 sanitize vfs_fsync calling conventions
Now that the last user passing a NULL file pointer is gone we can remove
the redundant dentry argument and associated hacks inside vfs_fsynmc_range.

The next step will be removig the dentry argument from ->fsync, but given
the luck with the last round of method prototype changes I'd rather
defer this until after the main merge window.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2010-05-21 18:31:21 -04:00
Eric W. Biederman 3ff195b011 sysfs: Implement sysfs tagged directory support.
The problem.  When implementing a network namespace I need to be able
to have multiple network devices with the same name.  Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.

What this patch does is to add an additional tag field to the
sysfs dirent structure.  For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible.  Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.

I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.

For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded.  Which means I need
a simple race free way to setup those directories as tagged.

To achieve a reace free design all tagged directories are created
and managed by sysfs itself.

Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid

- Implement mount_ns() which returns the ns of the calling process
  so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.

Everything else is left up to sysfs and the driver layer.

For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.

Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.

The work needed in sysfs is more extensive.  At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent.  Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.

Currently only directories which hold kobjects, and
symlinks are supported.  There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:37:31 -07:00
NeilBrown be6800a73a md: don't insist on valid event count for spare devices.
Devices which know that they are spares do not really need to have
an event count that matches the rest of the array, so there are no
data-in-sync issues. It is enough that the uuid matches.
So remove the requirement that the event count is up-to-date.

We currently still write out and event count on spares, but this
allows us in a year or 3 to stop doing that completely.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:28:01 +10:00
NeilBrown a8707c08f4 md: simplify updating of event count to sometimes avoid updating spares.
When updating the event count for a simple clean <-> dirty transition,
we try to avoid updating the spares so they can safely spin-down.
As the event_counts across an array must be +/- 1, this means
decrementing the event_count on a dirty->clean transition.
This is not always safe and we have to avoid the unsafe time.
We current do this with a misguided idea about it being safe or
not depending on whether the event_count is odd or even.  This
approach only works reliably in a few common instances, but easily
falls down.

So instead, simply keep internal state concerning whether it is safe
or not, and always assume it is not safe when an array is first
assembled.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:28:01 +10:00
Gabriele A. Trombetti 7b0bb5368a md/raid6: Fix raid-6 read-error correction in degraded state
Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.

Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2010-05-18 15:28:00 +10:00
NeilBrown 75a73a29e5 md: restore ability of spare drives to spin down.
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down.  Device failure/removal
etc are still recorded on spares.

However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:

   This means that the alignment between 'odd/even' and
    'clean/dirty' might take a little longer to attain,

how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.

So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately.  There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update).  We just piggy-back on that.

Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2010-05-18 15:28:00 +10:00
NeilBrown af3a2cd6b8 md: Fix read balancing in RAID1 and RAID10 on drives > 2TB
read_balance uses a "unsigned long" for a sector number which
will get truncated beyond 2TB.
This will cause read-balancing to be non-optimal, and can cause
data to be read from the 'wrong' branch during a resync.  This has a
very small chance of returning wrong data.

Reported-by: Jordan Russell <jr-list-2010@quo.to>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:28:00 +10:00
NeilBrown 2dc40f8094 md/linear: standardise all printk messages
md/linear:mdname:

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:59 +10:00
NeilBrown b5a20961f3 md/raid0: tidy up printk messages.
All messages now start
   md/raid0:md-device-name:

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:59 +10:00
NeilBrown 128595ed6f md/raid10: tidy up printk messages.
All raid10 printk messages now start
   md/raid10:md-device-name:

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:59 +10:00
NeilBrown 9dd1e2faf7 md/raid1: improve printk messages
Make sure the array name is included in a uniform way in all printk
messages.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:59 +10:00
NeilBrown 0c55e02259 md/raid5: improve consistency of error messages.
Many 'printk' messages from the raid456 module mention 'raid5' even
though it may be a 'raid6' or even 'raid4' array.  This can cause
confusion.
Also the actual array name is not always reported and when it is
it is not reported consistently.

So change all the messages to start:
    md/raid:%s:
where '%s' becomes e.g. md3 to identify the particular array.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:58 +10:00
NeilBrown 08fb730ca3 md: remove EXPERIMENTAL designation from RAID10
RAID10 has been available for quite a while now and is quite well
tested, so we can remove the EXPERIMENTAL designation.

Reported-by: Eric MSP Veith <eveith@wwweb-library.net>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:58 +10:00
Dan Williams f2859af671 md: allow integers to be passed to md/level
e.g. allow md to interpret 'echo 4 > md/level' as a request for raid4.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2010-05-18 15:27:58 +10:00
Dan Williams bb7f8d2217 md: notify mdstat waiters of level change
Level modifications change the output of mdstat.  The mdmon manager
thread is interested in these events for external metadata management.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2010-05-18 15:27:57 +10:00
Dan Williams f1b29bcae1 md/raid4: permit raid0 takeover
For consistency allow raid4 to takeover raid0 in addition to raid5 (with a
raid4 layout).

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2010-05-18 15:27:57 +10:00
NeilBrown e555190d82 md/raid1: delay reads that could overtake behind-writes.
When a raid1 array is configured to support write-behind
on some devices, it normally only reads from other devices.
If all devices are write-behind (because the rest have failed)
it is possible for a read request to be serviced before a
behind-write request, which would appear as data corruption.

So when forced to read from a WriteMostly device, wait for any
write-behind to complete, and don't start any more behind-writes.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:57 +10:00
NeilBrown d754c5ae1f md/raid1: fix confusing 'redirect sector' message.
This message seems to suggest the named device is the one on which a
read failed, however it is actually the device that the read will be
redirected to.
So make the message a little clearer.

Reported-by: Tim Burgess <ozburgess@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:56 +10:00
NeilBrown 9e35b99c7e md: don't unregister the thread in mddev_suspend
This is
 - unnecessary because mddev_suspend is always followed by a call to
   ->stop, and each ->stop unregisters the thread, and
 - a problem as it makes it awkwards to suspend and then resume a
   device as we will want later.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:56 +10:00
NeilBrown fafd7fb052 md: factor out init code for an mddev
This is a simple factorisation that makes mddev_find easier to read.


Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:55 +10:00
NeilBrown 21a52c6d05 md: pass mddev to make_request functions rather than request_queue
We used to pass the personality make_request function direct
to the block layer so the first argument had to be a queue.
But now we have the intermediary md_make_request so it makes
at lot more sense to pass a struct mddev_s.
It makes it possible to have an mddev without its own queue too.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:55 +10:00
NeilBrown cca9cf90c5 md: call md_stop_writes from md_stop
This moves the call to the other side of set_readonly, but that should
not be an issue.
This encapsulates in 'md_stop' all of the functionality for internally
stopping the array, leaving all the interactions with externalities
(sysfs, request_queue, gendisk) in do_md_stop.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:54 +10:00
NeilBrown a4bd82d0d0 md: split md_set_readonly out of do_md_stop
Using do_md_stop to set an array to read-only is a little confusing.
Now most of the common code has been factored out, split
md_set_readonly off in to a separate function.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:54 +10:00
NeilBrown a047e12540 md: factor md_stop_writes out of do_md_stop.
Further refactoring of do_md_stop.
This one requires some explanation as it takes code from different
places in do_md_stop, so some re-ordering happens.

We only get into this part of do_md_stop if there are no active opens
of the device, so no writes can be happening and the device must have
been flushed.  In md_stop_writes we want to stop any internal sources
of writes - i.e. resync - and flush out the metadata.

The only code that was previously before some of this code is
code to clean up the queue, the mddev, the gendisk, or sysfs, all
of which is probably better after code that makes active changes (i.e.
triggers writes).

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:54 +10:00
NeilBrown 6177b472ab md: start to refactor do_md_stop
do_md_stop is large and clunky, so hard to understand.

This is a first step of refactoring, pulling two simple
sub-functions out.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:53 +10:00
NeilBrown fe60b01428 md: factor do_md_run to separate accesses to ->gendisk
As part of relaxing the binding between an mddev and gendisk,
we separate do_md_run into two functions.
  md_run does all the work internal to md
  do_md_run calls md_run and makes and changes to gendisk
     that are required.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:53 +10:00
NeilBrown b821eaa572 md: remove ->changed and related code.
We set ->changed to 1 and call check_disk_change at the end
of md_open so that bd_invalidated would be set and thus
partition rescan would happen appropriately.

Now that we call revalidate_disk directly, which sets bd_invalidates,
that indirection is no longer needed and can be removed.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:53 +10:00
NeilBrown 49ce6cea85 md: don't reference gendisk in getgeo
Using ->array_sectors rather than get_capacity() is more
direct and is a step towards relaxing the tight connection
between mddev and gendisk.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:52 +10:00
NeilBrown 490773268c md: move io accounting out of personalities into md_make_request
While I generally prefer letting personalities do as much as possible,
given that we have a central md_make_request anyway we may as well use
it to simplify code.
Also this centralises knowledge of ->gendisk which will help later.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:52 +10:00
NeilBrown 2b7f22284d md/raid5: small tidyup in raid5_align_endio
Diving through ->queue to find mddev is unnecessarily complex - there
is an easier path to finding mddev, so use that.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:50 +10:00
NeilBrown a78d38a1a1 md: add support for raid5 to raid4 conversion
This is unlikely to be wanted, but we may as well provide it
for completeness.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:49 +10:00
Maciej Trela 5cac7861b2 md: notify level changes through sysfs.
Level changes can be very significant, so make sure
to notify them via sysfs.

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:49 +10:00
NeilBrown 233fca36bb md: Relax checks on ->max_disks when external metadata handling is used.
When metadata is being managed by user-space, md doesn't know
what the maximum number of devices allowed in an array is
so ->max_disks is 0.  In this case we should allow any (+ve)
number of disks.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:49 +10:00
Maciej Trela b71031076e md: Correctly handle device removal via sysfs
Writing "none" to "../md/dev-xx/slot" removes that device
from being an active part of the array, but it didn't
set ->raid_disk to -1 to record this fact.


Signed-off-by: Maciej Trela <Maciej.Trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:48 +10:00
Trela, Maciej dab8b29248 md: Add support for Raid0->Raid10 takeover
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:48 +10:00
Trela, Maciej 9af204cf72 md: Add support for Raid5->Raid0 and Raid10->Raid0 takeover
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:48 +10:00
Trela Maciej 54071b3808 md:Add support for Raid0->Raid5 takeover
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:47 +10:00
NeilBrown 84707f38e7 md: don't use mddev->raid_disks in raid0 or raid10 while array is active.
In a subsequent patch we will make it possible to change
mddev->raid_disks while a RAID0 or RAID10 array is active.  This is
part of the process of reshaping such an array.

This means that we cannot use this value while processes requests
(it is OK to use it during initialisation as we are locked against
changes then).
Both RAID0 and RAID10 have the same value stored in the private data
structure, so use that value instead.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:47 +10:00
NeilBrown c0cc75f84e md: discard StateChanged device flag.
This was needed when sysfs files could only be 'notified'
from process context.  Now that we have sys_notify_direct,
we can call it directly from an interrupt.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:47 +10:00
H Hartley Sweeten 7b92813c3c drivers/md: Remove unnecessary casts of void *
void pointers do not need to be cast to other pointer types.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:46 +10:00
Paul Clements 696fcd535b md: expose max value of behind writes counter
Keep track of the maximum number of concurrent write-behind requests
for an md array and exposed this number in sysfs at
   md/bitmap/max_backlog_used

Writing any value to this file will clear it.

This allows userspace to be involved in tuning bitmap/backlog.

Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:46 +10:00
NeilBrown ee8b81b03d md: remove some dead fields from mddev_s
These fields have never been used.
commit 4b6d287f62
added them, but also added identical files to bitmap_super_s,
and only used the latter.

So remove these unused fields.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:45 +10:00
NeilBrown 964147d5c8 md/raid1: fix counting of write targets.
There is a very small race window when writing to a
RAID1 such that if a device is marked faulty at exactly the wrong
time, the write-in-progress will not be sent to the device,
but the bitmap (if present) will be updated to say that
the write was sent.

Then if the device turned out to still be usable as was re-added
to the array, the bitmap-based-resync would skip resyncing that
block, possibly leading to corruption.  This would only be a problem
if no further writes were issued to that area of the device (i.e.
that bitmap chunk).

Suitable for any pending -stable kernel.

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-18 15:27:13 +10:00
NeilBrown a64c876fd3 md: manage redundancy group in sysfs when changing level.
Some levels expect the 'redundancy group' to be present,
others don't.
So when we change level of an array we might need to
add or remove this group.

This requires fixing up the current practice of overloading ->private
to indicate (when ->pers == NULL) that something needs to be removed.
So create a new ->to_remove to fill that role.

When changing levels, we may need to add or remove attributes.  When
changing RAID5 -> RAID6, we both add and remove the same thing.  It is
important to catch this and optimise it out as the removal is delayed
until a lock is released, so trying to add immediately would cause
problems.


Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-17 14:45:40 +10:00
NeilBrown b6eb127d27 md: remove unneeded sysfs files more promptly
When an array is stopped we need to remove some
sysfs files which are dependent on the type of array.

We need to delay that deletion as deleting them while holding
reconfig_mutex can lead to deadlocks.

We currently delay them until the array is completely destroyed.
However it is possible to deactivate and then reactivate the array.
It is also possible to need to remove sysfs files when changing level,
which can potentially happen several times before an array is
destroyed.

So we need to delete these files more promptly: as soon as
reconfig_mutex is dropped.

We need to ensure this happens before do_md_run can restart the array,
so we use open_mutex for some extra locking.  This is not deadlock
prone.

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-17 14:40:07 +10:00
NeilBrown ef2f80ff73 md/linear: avoid possible oops and array stop
Since commit ef286f6fa6
it has been important that each personality clears
->private in the ->stop() function, or sets it to a
attribute group to be removed.
linear.c doesn't.  This can sometimes lead to an oops,
though it doesn't always.

Suitable for 2.6.33-stable and 2.6.34.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2010-05-17 14:38:18 +10:00
Dan Williams e221835046 md: set mddev readonly flag on blkdev BLKROSET ioctl
When the user sets the block device to readwrite then the mddev should
follow suit.  Otherwise, the BUG_ON in md_write_start() will be set to
trigger.

The reverse direction, setting mddev->ro to match a set readonly
request, can be ignored because the blkdev level readonly flag precludes
the need to have mddev->ro set correctly.  Nevermind the fact that
setting mddev->ro to 1 may fail if the array is in use.

Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-05-12 08:25:37 +10:00
NeilBrown 1176568de7 md: restore ability of spare drives to spin down.
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down.  Device failure/removal
etc are still recorded on spares.

However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:

   This means that the alignment between 'odd/even' and
    'clean/dirty' might take a little longer to attain,

how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.

So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately.  There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update).  We just piggy-back on that.

Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2010-05-07 21:10:57 +10:00
Gabriele A. Trombetti 87aa63000c md/raid6: Fix raid-6 read-error correction in degraded state
Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.

Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2010-05-07 21:10:35 +10:00
NeilBrown 6e3b96ed61 md/raid5: fix previous patch.
Previous patch changes stripe and chunk_number to sector_t but
mistakenly did not update all of the divisions to use sector_dev().

This patch changes all the those divisions (actually the '%' operator)
to sector_div.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2010-04-23 07:08:28 +10:00
NeilBrown 35f2a59119 md/raid5: allow for more than 2^31 chunks.
With many large drives and small chunk sizes it is possible
to create a RAID5 with more than 2^31 chunks.  Make sure this
works.

Reported-by: Brett King <king.br@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2010-04-20 14:13:34 +10:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Linus Torvalds 31cc1dd344 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
  md: deal with merge_bvec_fn in component devices better.
2010-03-18 16:55:24 -07:00
NeilBrown 627a2d3c29 md: deal with merge_bvec_fn in component devices better.
If a component device has a merge_bvec_fn then as we never call it
we must ensure we never need to.  Currently this is done by setting
max_sector to 1 PAGE, however this does not stop a bio being created
with several sub-page iovecs that would violate the merge_bvec_fn.

So instead set max_segments to 1 and set the segment boundary to the
same as a page boundary to ensure there is only ever one single-page
segment of IO requested at a time.

This can particularly be an issue when 'xen' is used as it is
known to submit multiple small buffers in a single bio.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2010-03-16 17:04:24 +11:00
Emese Revfy 52cf25d0ab Driver core: Constify struct sysfs_ops in struct kobj_type
Constify struct sysfs_ops.

This is part of the ops structure constification
effort started by Arjan van de Ven et al.

Benefits of this constification:

 * prevents modification of data that is shared
   (referenced) by many other structure instances
   at runtime

 * detects/prevents accidental (but not intentional)
   modification attempts on archs that enforce
   read-only kernel data at runtime

 * potentially better optimized code as the compiler
   can assume that the const data cannot be changed

 * the compiler/linker move const data into .rodata
   and therefore exclude them from false sharing

Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-07 17:04:49 -08:00
Takahiro Yasui f070304094 dm raid1: fix deadlock when suspending failed device
To prevent deadlock, bios in the hold list should be flushed before
dm_rh_stop_recovery() is called in mirror_suspend().

The recovery can't start because there are pending bios and therefore
dm_rh_stop_recovery deadlocks.

When there are pending bios in the hold list, the recovery waits for
the completion of the bios after recovery_count is acquired.
The recovery_count is released when the recovery finished, however,
the bios in the hold list are processed after dm_rh_stop_recovery() in
mirror_presuspend(). dm_rh_stop_recovery() also acquires recovery_count,
then deadlock occurs.

Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
2010-03-06 02:32:35 +00:00
Mike Snitzer 924e600d41 dm: eliminate some holes data structures
Eliminate a 4-byte hole in 'struct dm_io_memory' by moving 'offset' above the
'ptr' to which it applies (size reduced from 24 to 16 bytes).  And by
association, 1-4 byte hole is eliminated in 'struct dm_io_request' (size
reduced from 56 to 48 bytes).

Eliminate all 6 4-byte holes and 1 cache-line in 'struct dm_snapshot' (size
reduced from 392 to 368 bytes).

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:33 +00:00
Peter Rajnoha 3abf85b5b5 dm ioctl: introduce flag indicating uevent was generated
Set a new DM_UEVENT_GENERATED_FLAG when returning from ioctls to
indicate that a uevent was actually generated.  This tells the userspace
caller that it may need to wait for the event to be processed.

Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:31 +00:00
Mikulas Patocka a97f925a32 dm: free dm_io before bio_endio not after
Free the dm_io structure before calling bio_endio() instead of after it,
to ensure that the io_pool containing it is not referenced after it is
freed.

This partially fixes a problem described here
  https://www.redhat.com/archives/dm-devel/2010-February/msg00109.html

thread 1:
bio_endio(bio, io_error);
/* scheduling happens */
					thread 2:
					close the device
					remove the device
thread 1:
free_io(md, io);

Thread 2, when removing the device, sees non-empty md->io_pool (because the
io hasn't been freed by thread 1 yet) and may crash with BUG in mempool_free.
Thread 1 may also crash, when freeing into a nonexisting mempool.

To fix this we must make sure that bio_endio() is the last call and
the md structure is not accessed afterwards.

There is another bio_endio in process_barrier, but it is called from the thread
and the thread is destroyed prior to freeing the mempools, so this call is
not affected by the bug.

A similar bug exists with module unloads - the module may be unloaded
immediately after bio_endio - but that is more difficult to fix.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:29 +00:00
Nikanth Karthikesan 8215d6ec5f dm table: remove unused dm_get_device range parameters
Remove unused parameters(start and len) of dm_get_device()
and fix the callers.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:27 +00:00
Mike Snitzer 0f3649a9e3 dm ioctl: only issue uevent on resume if state changed
Only issue a uevent on a resume if the state of the device changed,
i.e. if it was suspended and/or its table was replaced.

Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:24 +00:00
Mikulas Patocka ede5ea0b8b dm raid1: always return error if all legs fail
If all mirror legs fail, always return an error instead of holding the
bio, even if the handle_errors option was set.  At present it is the
responsibility of the driver underneath us to deal with retries,
multipath etc.

The patch adds the bio to the failures list instead of holding it
directly.  do_failures tests first if all legs failed and, if so,
returns the bio with -EIO.  If any leg is still alive and handle_errors
is set, do_failures calls hold_bio.

Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:22 +00:00
Kiyoshi Ueda fb61264297 dm mpath: refactor pg_init
This patch pulls the pg_init path activation code out of
process_queued_ios() into a new function.

No functional change.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:18 +00:00
Kiyoshi Ueda 2bded7bd7e dm mpath: wait for pg_init completion when suspending
When suspending the device we must wait for all I/O to complete, but
pg-init may be still in progress even after flushing the workqueue
for kmpath_handlerd in multipath_postsuspend.

This patch waits for pg-init completion correctly in
multipath_postsuspend().

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:32:13 +00:00
Kiyoshi Ueda d0259bf0ee dm mpath: hold io until all pg_inits completed
m->queue_io is set to block processing I/Os, and it needs to be kept
while pg-init, which issues multiple path activations, is in progress.
But m->queue is cleared when a path activation completes without error
in pg_init_done(), even while other path activations are in progress.
That may cause undesired -EIO on paths which are not complete activation.

This patch fixes that by not clearing m->queue_io until all path
activations complete.

(Before the hardware handlers were moved into the SCSI layer, pg_init
only used one path.)

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:30:02 +00:00
Kiyoshi Ueda fce323dd68 dm mpath: avoid storing private suspended state
'suspended' flag in struct multipath was introduced to check whether
the multipath target is in suspended state, but the same check is
done through dm_suspended() now, so remove the flag and related code.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:29:59 +00:00
Kiyoshi Ueda ecdb2e257a dm table: remove dm_get from dm_table_get_md
Remove the dm_get() in dm_table_get_md() because dm_table_get_md() could
be called from presuspend/postsuspend, which are called while
mapped_device is in DMF_FREEING state, where dm_get() is not allowed.

Justification for that is the lifetime of both objects: As far as the
current dm design/implementation, mapped_device is never freed while
targets are doing something, because dm core waits for targets to become
quiet in dm_put() using presuspend/postsuspend.  So targets should be
able to touch mapped_device without holding reference count of the
mapped_device, and we should allow targets to touch mapped_device even
if it is in DMF_FREEING state.

Backgrounds:
I'm trying to remove the multipath internal queue, since dm core now has
a generic queue for request-based dm.  In the patch-set, the multipath
target wants to request dm core to start/stop queue.  One of such
start/stop requests can happen during postsuspend() while the target
waits for pg-init to complete, because the target stops queue when
starting pg-init and tries to restart it when completing pg-init.  Since
queue belongs to mapped_device, it involves calling dm_table_get_md()
and dm_put().  On the other hand, postsuspend() is called in dm_put()
for mapped_device which is in DMF_FREEING state, and that triggers
BUG_ON(DMF_FREEING) in the 2nd dm_put().

I had tried to solve this problem by changing only multipath not to
touch mapped_device which is in DMF_FREEING state, but I couldn't and I
came up with a question why we need dm_get() in dm_table_get_md().

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:29:52 +00:00
Moger, Babu f7b934c812 dm mpath: skip activate_path for failed paths
This patch adds two minor fixes while processing device mapper path activation.

Skip failed paths while calling activate_path.  If the path is already failed
then activate_path will fail for sure. We don't have to call in that case. In
some case this might cause prolonged retries unnecessarily.

Change the misleading message if the path being activated fails with SCSI_DH_NOSYS.

Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:29:49 +00:00
Moger, Babu 83c0d5d538 dm mpath: pass struct pgpath to pg init done
This patch removes some unnecessary argument casting. There is no
functional change with this patch.

Passes 'struct pgpath' through to pg_init_done() instead of the enclosed
'struct dm_path'.

Tested the changes with LSI storage..

CC: Chandra Seetharaman <chandra.seetharaman@us.ibm.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-03-06 02:29:45 +00:00
Linus Torvalds 0a135ba14d Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: add __percpu sparse annotations to what's left
  percpu: add __percpu sparse annotations to fs
  percpu: add __percpu sparse annotations to core kernel subsystems
  local_t: Remove leftover local.h
  this_cpu: Remove pageset_notifier
  this_cpu: Page allocator conversion
  percpu, x86: Generic inc / dec percpu instructions
  local_t: Move local.h include to ringbuffer.c and ring_buffer_benchmark.c
  module: Use this_cpu_xx to dynamically allocate counters
  local_t: Remove cpu_local_xx macros
  percpu: refactor the code in pcpu_[de]populate_chunk()
  percpu: remove compile warnings caused by __verify_pcpu_ptr()
  percpu: make accessors check for percpu pointer in sparse
  percpu: add __percpu for sparse.
  percpu: make access macros universal
  percpu: remove per_cpu__ prefix.
2010-03-03 07:34:18 -08:00
Martin K. Petersen 8a78362c4e block: Consolidate phys_segment and hw_segment limits
Except for SCSI no device drivers distinguish between physical and
hardware segment limits.  Consolidate the two into a single segment
limit.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-02-26 13:58:08 +01:00
Martin K. Petersen 086fa5ff08 block: Rename blk_queue_max_sectors to blk_queue_max_hw_sectors
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.

Also introduce a temporary wrapper for backwards compability.  This can
be removed after the merge window is closed.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-02-26 13:58:08 +01:00
Tejun Heo a29d8b8e2d percpu: add __percpu sparse annotations to what's left
Add __percpu sparse annotations to places which didn't make it in one
of the previous patches.  All converions are trivial.

These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors.  This patch doesn't affect normal builds.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Neil Brown <neilb@suse.de>
2010-02-17 11:17:38 +09:00
Alasdair G Kergon 9307f6b19a dm: sysfs revert add empty release function to avoid debug warning
Revert commit d2bb7df8ca at Greg's request.

    Author: Milan Broz <mbroz@redhat.com>
    Date:   Thu Dec 10 23:51:53 2009 +0000

    dm: sysfs add empty release function to avoid debug warning

    This patch just removes an unnecessary warning:
     kobject: 'dm': does not have a release() function,
     it is broken and must be fixed.

    The kobject is embedded in mapped device struct, so
    code does not need to release memory explicitly here.

Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-02-16 18:43:04 +00:00
Kiyoshi Ueda 9eef87da2a dm mpath: fix stall when requeueing io
This patch fixes the problem that system may stall if target's ->map_rq
returns DM_MAPIO_REQUEUE in map_request().
E.g. stall happens on 1 CPU box when a dm-mpath device with queue_if_no_path
     bounces between all-paths-down and paths-up on I/O load.

When target's ->map_rq returns DM_MAPIO_REQUEUE, map_request() requeues
the request and returns to dm_request_fn().  Then, dm_request_fn()
doesn't exit the I/O dispatching loop and continues processing
the requeued request again.
This map and requeue loop can be done with interrupt disabled,
so 1 CPU system can be stalled if this situation happens.

For example, commands below can stall my 1 CPU box within 1 minute or so:
  # dmsetup table mp
  mp: 0 2097152 multipath 1 queue_if_no_path 0 1 1 service-time 0 1 2 8:144 1 1
  # while true; do dd if=/dev/mapper/mp of=/dev/null bs=1M count=100; done &
  # while true; do \
  > dmsetup message mp 0 "fail_path 8:144" \
  > dmsetup suspend --noflush mp \
  > dmsetup resume mp \
  > dmsetup message mp 0 "reinstate_path 8:144" \
  > done

To fix the problem above, this patch changes dm_request_fn() to exit
the I/O dispatching loop once if a request is requeued in map_request().

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-02-16 18:43:01 +00:00
Takahiro Yasui 558569aa9d dm raid1: fix null pointer dereference in suspend
When suspending a failed mirror, bios are completed by mirror_end_io() and
__rh_lookup() in dm_rh_dec() returns NULL where a non-NULL return value is
required by design.  Fix this by not changing the state of the recovery failed
region from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end().

Issue

On 2.6.33-rc1 kernel, I hit the bug when I suspended the failed
mirror by dmsetup command.

BUG: unable to handle kernel NULL pointer dereference at 00000020
IP: [<f94f38e2>] dm_rh_dec+0x35/0xa1 [dm_region_hash]
...
EIP: 0060:[<f94f38e2>] EFLAGS: 00010046 CPU: 0
EIP is at dm_rh_dec+0x35/0xa1 [dm_region_hash]
EAX: 00000286 EBX: 00000000 ECX: 00000286 EDX: 00000000
ESI: eff79eac EDI: eff79e80 EBP: f6915cd4 ESP: f6915cc4
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process dmsetup (pid: 2849, ti=f6914000 task=eff03e80 task.ti=f6914000)
 ...
Call Trace:
 [<f9530af6>] ? mirror_end_io+0x53/0x1b1 [dm_mirror]
 [<f9413104>] ? clone_endio+0x4d/0xa2 [dm_mod]
 [<f9530aa3>] ? mirror_end_io+0x0/0x1b1 [dm_mirror]
 [<f94130b7>] ? clone_endio+0x0/0xa2 [dm_mod]
 [<c02d6bcb>] ? bio_endio+0x28/0x2b
 [<f952f303>] ? hold_bio+0x2d/0x62 [dm_mirror]
 [<f952f942>] ? mirror_presuspend+0xeb/0xf7 [dm_mirror]
 [<c02aa3e2>] ? vmap_page_range+0xb/0xd
 [<f9414c8d>] ? suspend_targets+0x2d/0x3b [dm_mod]
 [<f9414ca9>] ? dm_table_presuspend_targets+0xe/0x10 [dm_mod]
 [<f941456f>] ? dm_suspend+0x4d/0x150 [dm_mod]
 [<f941767d>] ? dev_suspend+0x55/0x18a [dm_mod]
 [<c0343762>] ? _copy_from_user+0x42/0x56
 [<f9417fb0>] ? dm_ctl_ioctl+0x22c/0x281 [dm_mod]
 [<f9417628>] ? dev_suspend+0x0/0x18a [dm_mod]
 [<f9417d84>] ? dm_ctl_ioctl+0x0/0x281 [dm_mod]
 [<c02c3c4b>] ? vfs_ioctl+0x22/0x85
 [<c02c422c>] ? do_vfs_ioctl+0x4cb/0x516
 [<c02c42b7>] ? sys_ioctl+0x40/0x5a
 [<c0202858>] ? sysenter_do_call+0x12/0x28

Analysis

When recovery process of a region failed, dm_rh_recovery_end() function
changes the state of the region from RM_RH_RECOVERING to DM_RH_NOSYNC.
When recovery_complete() is executed between dm_rh_update_states() and
dm_writes() in do_mirror(), bios are processed with the region state,
DM_RH_NOSYNC. However, the region data is freed without checking its
pending count when dm_rh_update_states() is called next time.

When bios are finished by mirror_end_io(), __rh_lookup() in dm_rh_dec()
returns NULL even though a valid return value are expected.

Solution

Remove the state change of the recovery failed region from DM_RH_RECOVERING
to DM_RH_NOSYNC in dm_rh_recovery_end(). We can remove the state change
because:

  - If the region data has been released by dm_rh_update_states(),
    a new region data is created with the state of DM_RH_NOSYNC, and
    bios are processed according to the DM_RH_NOSYNC state.

  - If the region data has not been released by dm_rh_update_states(),
    a state of the region is DM_RH_RECOVERING and bios are put in the
    delayed_bio list.

The flag change from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end()
was added in the following commit:
  dm raid1: handle resync failures
  author  Jonathan Brassow <jbrassow@redhat.com>
    Thu, 12 Jul 2007 16:29:04 +0000 (17:29 +0100)
  http://git.kernel.org/linus/f44db678edcc6f4c2779ac43f63f0b9dfa28b724

Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-02-16 18:42:58 +00:00
Mikulas Patocka 5528d17de1 dm raid1: fail writes if errors are not handled and log fails
If the mirror log fails when the handle_errors option was not selected
and there is no remaining valid mirror leg, writes return success even
though they weren't actually written to any device.  This patch
completes them with EIO instead.

This code path is taken:
do_writes:
	bio_list_merge(&ms->failures, &sync);
do_failures:
	if (!get_valid_mirror(ms)) (false)
	else if (errors_handled(ms)) (false)
	else bio_endio(bio, 0);

The logic in do_failures is based on presuming that the write was already
tried: if it succeeded at least on one leg (without handle_errors) it
is reported as success.

Reference: https://bugzilla.redhat.com/show_bug.cgi?id=555197

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-02-16 18:42:55 +00:00
Jonathan Brassow ebfd32bba9 dm log: userspace fix overhead_size calcuations
This patch fixes two bugs that revolve around the miscalculation and
misuse of the variable 'overhead_size'.  'overhead_size' is the size of
the various header structures used during communication.

The first bug is the use of 'sizeof' with the pointer of a structure
instead of the structure itself - resulting in the wrong size being
computed.  This is then used in a check to see if the payload
(data_size) would be to large for the preallocated structure.  Since the
bug produces a smaller value for the overhead, it was possible for the
structure to be breached.  (Although the current users of the code do
not currently send enough data to trigger this bug.)

The second bug is that the 'overhead_size' value is used to compute how
much of the preallocated space should be cleared before populating it
with fresh data.  This should have simply been 'sizeof(struct cn_msg)'
not overhead_size.  The fact that 'overhead_size' was computed
incorrectly made this problem "less bad" - leaving only a pointer's
worth of space at the end uncleared.  Thus, this bug was never producing
a bad result, but still needs to be fixed - especially now that the
value is computed correctly.

Cc: stable@kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-02-16 18:42:53 +00:00
Mike Snitzer 55f67f2ded dm snapshot: persistent annotate work_queue as on stack
chunk_io() declares its 'struct mdata_req' on the stack and then
initializes its 'struct work_struct' member.  Annotate the
initialization of this workqueue with INIT_WORK_ON_STACK to suppress a
debugobjects warning seen when CONFIG_DEBUG_OBJECTS_WORK is enabled.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-02-16 18:42:51 +00:00
Nikanth Karthikesan 781248c1b5 dm stripe: avoid divide by zero with invalid stripe count
If a table containing zero as stripe count is passed into stripe_ctr
the code attempts to divide by zero.

This patch changes DM_TABLE_LOAD to return -EINVAL if the stripe count
is zero.

We now get the following error messages:
  device-mapper: table: 253:0: striped: Invalid stripe count
  device-mapper: ioctl: error adding target to table

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2010-02-16 18:42:47 +00:00
NeilBrown ef286f6fa6 md: fix some lockdep issues between md and sysfs.
======
This fix is related to
    http://bugzilla.kernel.org/show_bug.cgi?id=15142
but does not address that exact issue.
======

sysfs does like attributes being removed while they are being accessed
(i.e. read or written) and waits for the access to complete.

As accessing some md attributes takes the same lock that is held while
removing those attributes a deadlock can occur.

This patch addresses 3 issues in md that could lead to this deadlock.

Two relate to calling flush_scheduled_work while the lock is held.
This is probably a bad idea in general and as we use schedule_work to
delete various sysfs objects it is particularly bad.

In one case flush_scheduled_work is called from md_alloc (called by
md_probe) called from do_md_run which holds the lock.  This call is
only present to ensure that ->gendisk is set.  However we can be sure
that gendisk is always set (though possibly we couldn't when that code
was originally written.  This is because do_md_run is called in three
different contexts:
  1/ from md_ioctl.  This requires that md_open has succeeded, and it
     fails if ->gendisk is not set.
  2/ from writing a sysfs attribute.  This can only happen if the
     mddev has been registered in sysfs which happens in md_alloc
     after ->gendisk has been set.
  3/ from autorun_array which is only called by autorun_devices, which
     checks for ->gendisk to be set before calling autorun_array.
So the call to md_probe in do_md_run can be removed, and the check on
->gendisk can also go.


In the other case flush_scheduled_work is being called in do_md_stop,
purportedly to wait for all md_delayed_delete calls (which delete the
component rdevs) to complete.  However there really isn't any need to
wait for them - they have already been disconnected in all important
ways.

The third issue is that raid5->stop() removes some attribute names
while the lock is held.  There is already some infrastructure in place
to delay attribute removal until after the lock is released (using
schedule_work).  So extend that infrastructure to remove the
raid5_attrs_group.

This does not address all lockdep issues related to the sysfs
"s_active" lock.  The rest can be address by splitting that lockdep
context between symlinks and non-symlinks which hopefully will happen.

Signed-off-by: NeilBrown <neilb@suse.de>
2010-02-10 11:26:09 +11:00
NeilBrown 9eb07c2592 md: fix 'degraded' calculation when starting a reshape.
This code was written long ago when it was not possible to
reshape a degraded array.  Now it is so the current level of
degraded-ness needs to be taken in to account.  Also newly addded
devices should only reduce degradedness if they are deemed to be
in-sync.

In particular, if you convert a RAID5 to a RAID6, and increase the
number of devices at the same time, then the 5->6 conversion will
make the array degraded so the current code will produce a wrong
value for 'degraded' - "-1" to be precise.

If the reshape runs to completion end_reshape will calculate a correct
new value for 'degraded', but if a device fails during the reshape an
incorrect decision might be made based on the incorrect value of
"degraded".

This patch is suitable for 2.6.32-stable and if they are still open,
2.6.31-stable and 2.6.30-stable as well.

Cc: stable@kernel.org
Reported-by: Michael Evans <mjevans1983@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2010-02-09 16:34:29 +11:00
Martin K. Petersen b27d7f16d3 DM: Fix device mapper topology stacking
Make DM use bdev_stack_limits() function so that partition offsets get
taken into account when calculating alignment.  Clarify stacking
warnings.

Also remove obsolete clearing of final alignment_offset and misalignment
flag.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair G. Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-01-11 14:29:20 +01:00
NeilBrown 404e4b43fd md: allow a resync that is waiting for other resync to complete, to be aborted.
If two arrays share a device, then they will not both resync at the
same time.  One will wait for the other to complete.
While waiting, the MD_RECOVERY_INTR flag is not checked so a device
failure, which would make the resync pointless, does not cause the
resync to abort, so the failed device cannot be removed (as it cannot
be remove while a resync is happening).

So add a test for MD_RECOVERY_INTR.

Reported-by: Brett Russ <bruss@netezza.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-30 15:25:23 +11:00
NeilBrown 7fb9dadc91 md: remove unnecessary code from do_md_run
Since commit dfc7064500,
->hot_remove_disks has not removed non-failed devices from
an array until recovery is no longer possible.
So the code in do_md_run to get around the fact that
md_check_recovery (which calls ->hot_remove_disks) would
remove partially-in-sync devices is no longer needed.

So remove it.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-30 15:20:43 +11:00
Dan Williams a2d79c324a md: make recovery started by do_md_run() visible via sync_action
By default md_do_sync() will perform recovery if no other actions are
specified.  However, action_show() relies on MD_RECOVERY_RECOVER to be
set otherwise it returns 'idle'.  So, add a missing set
MD_RECOVERY_RECOVER when starting recovery.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-30 15:20:31 +11:00
NeilBrown 0f9552b5dc md: fix small irregularity with start_ro module parameter
The start_ro modules parameter can be used to force arrays to be
started in 'auto-readonly' in which they are read-only until the first
write.  This ensures that no resync/recovery happens until something
else writes to the device.  This is important for resume-from-disk
off an md array.

However if an array is started 'readonly' (by writing 'readonly' to
the 'array_state' sysfs attribute) we want it to be really 'readonly',
not 'auto-readonly'.

So strengthen the condition to only set auto-readonly if the
array is not already read-only.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-30 15:20:12 +11:00
NeilBrown cbd1998377 md: Fix unfortunate interaction with evms
evms configures md arrays by:
  open device
  send ioctl
  close device

for each different ioctl needed.
Since 2.6.29, the device can disappear after the 'close'
unless a significant configuration has happened to the device.
The change made by "SET_ARRAY_INFO" can too minor to stop the device
from disappearing, but important enough that losing the change is bad.

So: make sure SET_ARRAY_INFO sets mddev->ctime, and keep the device
active as long as ctime is non-zero (it gets zeroed with lots of other
things when the array is stopped).

This is suitable for -stable kernels since 2.6.29.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2009-12-30 12:08:49 +11:00
Linus Torvalds 53365383c4 Merge git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (80 commits)
  dm snapshot: use merge origin if snapshot invalid
  dm snapshot: report merge failure in status
  dm snapshot: merge consecutive chunks together
  dm snapshot: trigger exceptions in remaining snapshots during merge
  dm snapshot: delay merging a chunk until writes to it complete
  dm snapshot: queue writes to chunks being merged
  dm snapshot: add merging
  dm snapshot: permit only one merge at once
  dm snapshot: support barriers in snapshot merge target
  dm snapshot: avoid allocating exceptions in merge
  dm snapshot: rework writing to origin
  dm snapshot: add merge target
  dm exception store: add merge specific methods
  dm snapshot: create function for chunk_is_tracked wait
  dm snapshot: make bio optional in __origin_write
  dm mpath: reject messages when device is suspended
  dm: export suspended state to targets
  dm: rename dm_suspended to dm_suspended_md
  dm: swap target postsuspend call and setting suspended flag
  dm crypt: add plain64 iv
  ...
2009-12-15 09:12:01 -08:00
Joe Perches 7b75c2f8cf drivers/md/md.c: use %pU to print UUIDs
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:33 -08:00
André Goddard Rosa e7d2860b69 tree-wide: convert open calls to remove spaces to skip_spaces() lib function
Makes use of skip_spaces() defined in lib/string.c for removing leading
spaces from strings all over the tree.

It decreases lib.a code size by 47 bytes and reuses the function tree-wide:
   text    data     bss     dec     hex filename
  64688     584     592   65864   10148 (TOTALS-BEFORE)
  64641     584     592   65817   10119 (TOTALS-AFTER)

Also, while at it, if we see (*str && isspace(*str)), we can be sure to
remove the first condition (*str) as the second one (isspace(*str)) also
evaluates to 0 whenever *str == 0, making it redundant. In other words,
"a char equals zero is never a space".

Julia Lawall tried the semantic patch (http://coccinelle.lip6.fr) below,
and found occurrences of this pattern on 3 more files:
    drivers/leds/led-class.c
    drivers/leds/ledtrig-timer.c
    drivers/video/output.c

@@
expression str;
@@

( // ignore skip_spaces cases
while (*str &&  isspace(*str)) { \(str++;\|++str;\) }
|
- *str &&
isspace(*str)
)

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:32 -08:00
Dan Williams 06e3c817b7 md: add 'recovery_start' per-device sysfs attribute
Enable external metadata arrays to manage rebuild checkpointing via a
md/dev-XXX/recovery_start attribute which reflects rdev->recovery_offset

Also update resync_start_store to allow 'none' to be written, for
consistency.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:58:57 +11:00
Dan Williams 4e59ca7da0 md: rcu_read_lock() walk of mddev->disks in md_do_sync()
Other walks of this list are either under rcu_read_lock() or the list
mutation lock (mddev_lock()).  This protects against the improbable case of a
disk being removed from the array at the start of md_do_sync().

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-12-14 12:57:43 +11:00
NeilBrown 93be75ffde md: integrate spares into array at earliest opportunity.
As v1.x metadata can record that a member of the array is
not completely recovered, it make sense to record that a
spare has become a regular member of the array at the earliest
opportunity.
So remove the tests on "recovery_offset > 0" in super_1_sync
as they really aren't needed, and schedule a metadata update
immediately after adding spares to a degraded array.

This means that if a crash happens immediately after a recovery
starts, the new device will be included in the array and recovery will
continue from wherever it was up to.  Previously this didn't happen
unless recovery was at least 1/16 of the way through.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
Arnd Bergmann aa98aa3198 md: move compat_ioctl handling into md.c
The RAID ioctls are only implemented in md.c, so the
handling for them should also be moved there from
fs/compat_ioctl.c.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Brown <neilb@suse.de>
Cc: Andre Noll <maan@systemlinux.org>
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 93bd89a6d5 md: revise Kconfig help for MD_MULTIPATH
Make it clear in the config message that MD_MULTIPATH is not under
active development.

Cc: Oren Held <orenhe@il.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 0efb9e6191 md: add MODULE_DESCRIPTION for all md related modules.
Suggested by  Oren Held <orenhe@il.ibm.com>

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
Robert Becker 1e50915fe0 raid: improve MD/raid10 handling of correctable read errors.
We've noticed severe lasting performance degradation of our raid
arrays when we have drives that yield large amounts of media errors.
The raid10 module will queue each failed read for retry, and also
will attempt call fix_read_error() to perform the read recovery.
Read recovery is performed while the array is frozen, so repeated
recovery attempts can degrade the performance of the array for
extended periods of time.

With this patch I propose adding a per md device max number of
corrected read attempts.  Each rdev will maintain a count of
read correction attempts in the rdev->read_errors field (not
used currently for raid10). When we enter fix_read_error()
we'll check to see when the last read error occurred, and
divide the read error count by 2 for every hour since the
last read error. If at that point our read error count
exceeds the read error threshold, we'll fail the raid device.

In addition in this patch I add sysfs nodes (get/set) for
the per md max_read_errors attribute, the rdev->read_errors
attribute, and added some printk's to indicate when
fix_read_error fails to repair an rdev.

For testing I used debugfs->fail_make_request to inject
IO errors to the rdev while doing IO to the raid array.

Signed-off-by: Robert Becker <Rob.Becker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
Robert Becker 67b8dc4b06 md/raid10: print more useful messages on device failure.
When we get a read error on a device in a RAID10, and attempting to
repair the error fails, print more useful messages about why it
failed.

Signed-off-by: Robert Becker <Rob.Becker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown ffa23322b1 md/bitmap: update dirty flag when bitmap bits are explicitly set.
There is a sysfs file which allows bits in the write-intent
bitmap to be explicit set - indicating that the block is thought
to be 'dirty'.
When this happens we should really set recovery_cp backwards
to include the block to reflect this dirtiness.

In particular, a 'resync' process will refuse to start if
recovery_cp is beyond the end of the array, so this is needed
to allow a resync to be triggered.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown ece5cff0da md: Support write-intent bitmaps with externally managed metadata.
In this case, the metadata needs to not be in the same
sector as the bitmap.
md will not read/write any bitmap metadata.  Config must be
done via sysfs and when a recovery makes the array non-degraded
again, writing 'true' to 'bitmap/can_clear' will allow bits in
the bitmap to be cleared again.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 624ce4f565 md/bitmap: move setting of daemon_lastrun out of bitmap_read_sb
Setting daemon_lastrun really has nothing to do with reading
the bitmap superblock, it just happens to be needed at the same time.
bitmap_read_sb is about to become options, so move that code out
to after the call to bitmap_read_sb.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 43a705076e md: support updating bitmap parameters via sysfs.
A new attribute directory 'bitmap' in 'md' is created which
contains files for configuring the bitmap.
'location' identifies where the bitmap is, either 'none',
or 'file' or 'sector offset from metadata'.
Writing 'location' can create or remove a bitmap.
Adding a 'file' bitmap this way is not yet supported.
'chunksize' and 'time_base' must be set before 'location'
can be set.

'chunksize' can be set before creating a bitmap, but is
currently always over-ridden by the bitmap superblock.

'time_base' and 'backlog' can be updated at any time.


Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
2009-12-14 12:51:41 +11:00
NeilBrown 72e02075a3 md: factor out parsing of fixed-point numbers
safe_delay_store can parse fixed point numbers (for fractions
of a second).  We will want to do that for another sysfs
file soon, so factor out the code.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown f6af949c56 md: support bitmap offset appropriate for external-metadata arrays.
For md arrays were metadata is managed externally, the kernel does not
know about a superblock so the superblock offset is 0.
If we want to have a write-intent-bitmap near the end of the
devices of such an array, we should support sector_t sized offset.
We need offset be possibly negative for when the bitmap is before
the metadata, so use loff_t instead.

Also add sanity check that bitmap does not overlap with data.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 9cd30fdc33 md: remove needless setting of thread->timeout in raid10_quiesce
As bitmap_create and bitmap_destroy already set thread->timeout
as appropriate, there is no need to do it in raid10_quiesce.
There is a possible need to wake the thread after the timeout
has been set low, but it is better to do that where the timeout
is actually set low, in bitmap_create.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 1b04be96f6 md: change daemon_sleep to be in 'jiffies' rather than 'seconds'.
This removes a lot of multiplications by HZ.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 42a04b5078 md: move offset, daemon_sleep and chunksize out of bitmap structure
... and into bitmap_info.  These are all configuration parameters
that need to be set before the bitmap is created.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown c3d9714e88 md: collect bitmap-specific fields into one structure.
In preparation for making bitmap fields configurable via sysfs,
start tidying up by making a single structure to contain the
configuration fields.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 709ae4879a md/raid1: add takeover support for raid5->raid1
A 2-device raid5 array can now be converted to raid1.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:41 +11:00
NeilBrown 6eef4b21ff md: add honouring of suspend_{lo,hi} to raid1.
This will allow us to stop writeout to portions of the array
while  they are resynced by someone else - e.g. another node in
a cluster.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:40 +11:00
NeilBrown 729a18663a md/raid5: don't complete make_request on barrier until writes are scheduled
The post-barrier-flush is sent by md as soon as make_request on the
barrier write completes.  For raid5, the data might not be in the
per-device queues yet.  So for barrier requests, wait for any
pre-reading to be done so that the request will be in the per-device
queues.

We use the 'preread_active' count to check that nothing is still in
the preread phase, and delay the decrement of this count until after
write requests have been submitted to the underlying devices.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:51:40 +11:00
NeilBrown a2826aa92e md: support barrier requests on all personalities.
Previously barriers were only supported on RAID1.  This is because
other levels requires synchronisation across all devices and so needed
a different approach.
Here is that approach.

When a barrier arrives, we send a zero-length barrier to every active
device.  When that completes - and if the original request was not
empty -  we submit the barrier request itself (with the barrier flag
cleared) and then submit a fresh load of zero length barriers.

The barrier request itself is asynchronous, but any subsequent
request will block until the barrier completes.

The reason for clearing the barrier flag is that a barrier request is
allowed to fail.  If we pass a non-empty barrier through a striping
raid level it is conceivable that part of it could succeed and part
could fail.  That would be way too hard to deal with.
So if the first run of zero length barriers succeed, we assume all is
sufficiently well that we send the request and ignore errors in the
second run of barriers.

RAID5 needs extra care as write requests may not have been submitted
to the underlying devices yet.  So we flush the stripe cache before
proceeding with the barrier.

Note that the second set of zero-length barriers are submitted
immediately after the original request is submitted.  Thus when
a personality finds mddev->barrier to be set during make_request,
it should not return from make_request until the corresponding
per-device request(s) have been queued.

That will be done in later patches.

Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Andre Noll <maan@systemlinux.org>
2009-12-14 12:49:49 +11:00
NeilBrown efa593390e md: don't reset curr_resync_completed after an interrupted resync
If a resync/recovery/check/repair is interrupted for some reason, it
can be useful to know exactly where it got up to.
So in that case, do not clear curr_resync_completed.
Initialise it when starting a resync/recovery/... instead.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:49:49 +11:00
NeilBrown c07b70ad32 md: adjust resync_min usefully when resync aborts.
When a 'check' or 'repair' finished we should clear resync_min
so that a future check/repair will cover the whole array (by default).
However if it is interrupted, we should update resync_min to
where we got up to, so that when the check/repair continues it
just does the remainder of the array.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:49:48 +11:00
NeilBrown 7820f9e1dd md: remove sparse warning:symbol XXX was not declared.
Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:49:47 +11:00
NeilBrown 8553fe7ec7 md/raid5: remove some sparse warnings.
qd_idx is previously declared and given exactly the same value!

Signed-off-by: NeilBrown <neilb@suse.de>
2009-12-14 12:49:47 +11:00
NeilBrown aa5cbd1038 md/bitmap: protect against bitmap removal while being updated.
A write intent bitmap can be removed from an array while the
array is active.
When this happens, all IO is suspended and flushed before the
bitmap is removed.
However it is possible that bitmap_daemon_work is still running to
clear old bits from the bitmap.  If it is, it can dereference the
bitmap after it has been freed.

So introduce a new mutex to protect bitmap_daemon_work and get it
before destroying a bitmap.

This is suitable for any current -stable kernel.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2009-12-14 12:49:46 +11:00
Mikulas Patocka d2fdb776e0 dm snapshot: use merge origin if snapshot invalid
If the snapshot we are merging became invalid (e.g. it ran out of
space) redirect all I/O directly to the origin device.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:36 +00:00
Mike Snitzer d8ddb1cfff dm snapshot: report merge failure in status
Set 'merge_failed' flag if a snapshot fails to merge.  Update
snapshot_status() to report "Merge failed" if 'merge_failed' is set.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:35 +00:00
Mike Snitzer 8a2d528620 dm snapshot: merge consecutive chunks together
s->store->type->prepare_merge returns the number of chunks that can be
copied linearly working backwards from the returned chunk number.

For example, if it returns 3 chunks with old_chunk == 10 and new_chunk
== 20, then chunk 20 can be copied to 10, chunk 19 to 9 and 18 to 8.

Until now kcopyd only copied one chunk at a time.  This patch now copies
the full set at once.

Consequently, snapshot_merge_process() needs to delay the merging of all
chunks if any have writes in progress, not just the first chunk in the
region that is to be merged.

snapshot-merge's performance is now comparable to the original
snapshot-origin target.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:34 +00:00
Mikulas Patocka 73dfd078cf dm snapshot: trigger exceptions in remaining snapshots during merge
When there is one merging snapshot and other non-merging snapshots,
snapshot_merge_process() must make exceptions in the non-merging
snapshots.

Use a sequence count to resolve the race between I/O to chunks that are
about to be merged.  The count increases each time an exception
reallocation finishes.  Use wait_event() to wait until the count
changes.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:34 +00:00
Mikulas Patocka 17aa03326d dm snapshot: delay merging a chunk until writes to it complete
Track writes to chunks that are currently being merged and delay merging
a chunk until all writes to that chunk finish.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:33 +00:00
Mikulas Patocka 9fe8625488 dm snapshot: queue writes to chunks being merged
While a set of chunks is being merged, any overlapping writes need to be
queued.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:33 +00:00
Mikulas Patocka 1e03f97e43 dm snapshot: add merging
Merging is started when origin is resumed and it is stopped when
origin is suspended or when the merging snapshot is destroyed or
errors are detected.

Merging is not yet interlocked with writes: this will be handled in
subsequent patches.

The code relies on callbacks from a private kcopyd thread.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:32 +00:00
Mikulas Patocka 9d3b15c4c7 dm snapshot: permit only one merge at once
Merging more than one snapshot is not supported, so prevent
this happening.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:32 +00:00
Mike Snitzer 10b8106a70 dm snapshot: support barriers in snapshot merge target
Sets num_flush_requests=2 to support flushing both the origin and cow
devices used by the snapshot-merge target.

Also, snapshot_ctr() now gets the origin device using FMODE_WRITE if the
target is snapshot-merge (which writes to the origin device).

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:31 +00:00
Mikulas Patocka 3452c2a1eb dm snapshot: avoid allocating exceptions in merge
The snapshot-merge target should not allocate new exceptions because the
intent is to merge all of its exceptions as quickly and safely as
possible.

This patch introduces the snapshot-merge mapping function and updates
__origin_write() so that it doesn't allocate exceptions on any snapshots
that are being merged.

If a write request to a merging snapshot device is to be dispatched
directly to the origin (because the chunk is not remapped or was already
merged), snapshot_merge_map() must make exceptions in other snapshots so
calls do_origin().

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:31 +00:00
Mikulas Patocka 515ad66cc4 dm snapshot: rework writing to origin
To track the completion of exceptions relating to the same location on
the device, the current code selects one exception as primary_pe, links
the other exceptions to it and uses reference counting to wait until all
the reallocations are complete.

It is considered too complicated to extend this code to handle the new
snapshot-merge target, where sets of non-overlapping chunks would also
need to become linked.

Instead, a simpler (but less efficient) approach is taken.  Bios are
linked to one exception.  When it completes, bios are simply retried,
and if other related exceptions are still outstanding, they'll get
queued again to wait for another one.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:30 +00:00
Mikulas Patocka d698aa4500 dm snapshot: add merge target
The snapshot-merge target allows a snapshot to be merged back into the
snapshot's origin device.

One anticipated use of snapshot merging is the rollback of filesystems
to back out problematic system upgrades.

This patch adds snapshot-merge target management to both
dm_snapshot_init() and dm_snapshot_exit().  As an initial place-holder,
snapshot-merge is identical to the snapshot target.  Documentation is
provided.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:30 +00:00
Mikulas Patocka 4454a6216f dm exception store: add merge specific methods
Add functions that decide how many consecutive chunks of snapshot to
merge back into the origin next and to update the metadata afterwards.

prepare_merge provides a pointer to the most recent still-to-be-merged
chunk and returns how many previous ones are consecutive and can be
processed together.

commit_merge removes the nr_merged most-recent chunks permanently from
the exception store.  The number must not exceed that returned by
prepare_merge.

Introduce NUM_SNAPSHOT_HDR_CHUNKS to show where the snapshot header
chunk is accounted for.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:29 +00:00
Mike Snitzer 615d1eb9ca dm snapshot: create function for chunk_is_tracked wait
Move the __chunk_is_tracked() loop into a separate function as we will
also need to call it from the write path in the rare case of conflicting
writes to the same chunk.

Originally introduced in commit a8d41b59f3
("dm snapshot: fix race during exception creation").

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:29 +00:00
Mikulas Patocka 9eaae8ffbc dm snapshot: make bio optional in __origin_write
To support the merging of snapshots back into their origin we need
to trigger exceptions in other snapshots not being merged without
any incoming bio on the origin device.  The bio parameter to
__origin_write() becomes optional and the sector needs supplying
separately.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:28 +00:00
Kiyoshi Ueda c2f3d24b78 dm mpath: reject messages when device is suspended
This patch rejects messages that can generate I/O while the device
itself is suspended.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:27 +00:00
Kiyoshi Ueda 64dbce580d dm: export suspended state to targets
This patch adds the exported dm_suspended() function so that targets
can check whether or not they are suspended.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:27 +00:00
Kiyoshi Ueda 4f186f8bbf dm: rename dm_suspended to dm_suspended_md
This patch renames dm_suspended() to dm_suspended_md() and
keeps it internal to dm.
No functional change.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:26 +00:00
Kiyoshi Ueda 4d4471cb5c dm: swap target postsuspend call and setting suspended flag
This patch moves DMF_SUSPENDED flag set before postsuspend.
No one should care about the ordering, because the flag set and
the postsuspend are protected by a single lock, md->suspend_lock,
and all strict flag-checkers take the lock.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:26 +00:00
Milan Broz 61afef614b dm crypt: add plain64 iv
The default plain IV is 32-bit only.

This plain64 IV provides a compatible mode for encrypted devices bigger
than 4TB.

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:25 +00:00
Jun'ichi Nomura 6db4ccd635 dm: trace request based remapping
This patch adds a remapping trace to request-based dm.
BIO-based dm already has the equivalent tracepoint.

For example, under this dm stack (linear LV on multipath):
  # dmsetup ls --tree -o ascii
  vg-lv0 (253:1)
   `-mpath0 (253:0)
      |- (8:160)
      |- (66:80)
      |- (65:176)
      `- (65:160)

Trace of 'dd of=/dev/vg/lv0 bs=128k count=1 oflag=direct' looks like this:

without the patch:
  dd-6674  [000]   539.727384: block_bio_queue: 253,1 WS 0 + 256 [dd]
  dd-6674  [000]   539.727392: block_remap: 253,0 WS 384 + 256 <- (253,1) 0
  dd-6674  [000]   539.727394: block_bio_queue: 253,0 WS 384 + 256 [dd]
  dd-6674  [000]   539.727405: block_getrq: 253,0 WS 384 + 256 [dd]
  dd-6674  [000]   539.727409: block_plug: [dd]
  dd-6674  [000]   539.727410: block_rq_insert: 253,0 W 0 () 384 + 256 [dd]
  dd-6674  [000]   539.727416: block_rq_issue: 253,0 W 0 () 384 + 256 [dd]
  dd-6674  [000]   539.727426: block_rq_insert: 65,176 W 0 () 384 + 256 [dd]
  dd-6674  [000]   539.727427: block_rq_issue: 65,176 W 0 () 384 + 256 [dd]
  ...

and with the patch: (the line with '**' is the trace added by this patch)
  dd-6617  [002]   162.914301: block_bio_queue: 253,1 WS 0 + 256 [dd]
  dd-6617  [002]   162.914314: block_remap: 253,0 WS 384 + 256 <- (253,1) 0
  dd-6617  [002]   162.914316: block_bio_queue: 253,0 WS 384 + 256 [dd]
  dd-6617  [002]   162.914331: block_getrq: 253,0 WS 384 + 256 [dd]
  dd-6617  [002]   162.914335: block_plug: [dd]
  dd-6617  [002]   162.914337: block_rq_insert: 253,0 W 0 () 384 + 256 [dd]
  dd-6617  [002]   162.914347: block_rq_issue: 253,0 W 0 () 384 + 256 [dd]
**dd-6617  [002]   162.914356: block_rq_remap: 65,176 W 384 + 256 <- (253,0) 384
  dd-6617  [002]   162.914358: block_rq_insert: 65,176 W 0 () 384 + 256 [dd]
  dd-6617  [002]   162.914359: block_rq_issue: 65,176 W 0 () 384 + 256 [dd]
  ...

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:25 +00:00
Mike Snitzer c1f0c183f6 dm snapshot: allow live exception store handover between tables
Permit in-use snapshot exception data to be 'handed over' from one
snapshot instance to another.  This is a pre-requisite for patches
that allow the changes made in a snapshot device to be merged back into
its origin device and also allows device resizing.

The basic call sequence is:

  dmsetup load new_snapshot (referencing the existing in-use cow device)
     - the ctr code detects that the cow is already in use and allows the
       two snapshot target instances to be linked together
  dmsetup suspend original_snapshot
  dmsetup resume new_snapshot
     - the new_snapshot becomes live, and if anything now tries to access
       the original one it will receive -EIO
  dmsetup remove original_snapshot

(There can only be two snapshot targets referencing the same cow device
simultaneously.)

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:24 +00:00
Alasdair G Kergon 042d2a9bcd dm: keep old table until after resume succeeded
When swapping a new table into place, retain the old table until
its replacement is in place.

An old check for an empty table is removed because this is enforced
in populate_table().

__unbind() becomes redundant when followed by __bind().

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:24 +00:00
Alasdair G Kergon a794015597 dm: bind new table before destroying old
When replacing a mapped device's table during a 'resume', delay the
destruction of the old table until the new one is successfully in place.

This will make it easier for a later patch to transfer internal state
information from the old table to the new one (something we do not currently
support) while giving us more options for reversion if a later part
of the operation fails.

Devices are always in the suspended state during dm_swap_table().
This patch reinforces the requirement that all I/O must have been
flushed from the table targets while in this state (including any in
workqueues).  In the case of 'noflush' suspending, unprocessed
I/O should have been 'pushed back' to the dm core prior to this point,
for resubmission after the new table is in place.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:23 +00:00
Mike Snitzer 1d0f3ce832 dm ioctl: retrieve status from inactive table
Add the flag DM_QUERY_INACTIVE_TABLE_FLAG to the ioctls to return
infomation about the loaded-but-not-yet-active table instead of the live
table.  Prior to this patch it was impossible to obtain this information
until the device had been 'resumed'.

Userspace dmsetup and libdevmapper support the flag as of version 1.02.40.
e.g. dmsetup info --inactive vg1-lv1

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:22 +00:00
Mikulas Patocka 12fc0f49dc dm io: handle empty barriers
Accept empty barriers in dm-io.

dm-io will process empty write barrier requests just like the other
read/write requests.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:22 +00:00
Mike Anderson 67a46dad25 dm mpath: prevent io from work queue while suspended
Reject messages that can generate I/O while the device itself
is suspended.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:21 +00:00
Mike Anderson 6380f26f04 dm mpath: add mutex to synchronize adding and flushing work
Add a mutex to allow possible creators of new work to synchronize with
flushing work queues.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:21 +00:00
Mike Anderson c50abeb380 dm ioctl: forbid messages to devices being deleted
Once we begin deleting a device, prevent any further messages being sent
to targets of its table (to avoid races).

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:20 +00:00
Mike Anderson 432a212c0d dm: add dm_deleting_md function
Add dm_deleting_md to check whether or not a given mapped
device is currently being deleted.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:20 +00:00
Kiyoshi Ueda 6df400ab64 dm mpath: flush workqueues before suspend completes
This patch stops the remaining dm-mpath activity during the suspend
sequence by flushing workqueues in postsuspend function.

The current dm-mpath target may not be quiet even after suspend completes
because some workqueues (e.g. device_handler's work, event handling)
are not flushed during the suspend sequence, even though suspended
devices/targets are supposed to be quiet in this state.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:19 +00:00
Alasdair G Kergon 7c6664114b dm: rename dm_get_table to dm_get_live_table
Rename dm_get_table to dm_get_live_table.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:19 +00:00
Kiyoshi Ueda d0bcb87865 dm: add request based barrier support
This patch adds barrier support for request-based dm.

CORE DESIGN

The design is basically same as bio-based dm, which emulates barrier
by mapping empty barrier bios before/after a barrier I/O.
But request-based dm has been using struct request_queue for I/O
queueing, so the block-layer's barrier mechanism can be used.

o Summary of the block-layer's behavior (which is depended by dm-core)
  Request-based dm uses QUEUE_ORDERED_DRAIN_FLUSH ordered mode for
  I/O barrier.  It means that when an I/O requiring barrier is found
  in the request_queue, the block-layer makes pre-flush request and
  post-flush request just before and just after the I/O respectively.

  After the ordered sequence starts, the block-layer waits for all
  in-flight I/Os to complete, then gives drivers the pre-flush request,
  the barrier I/O and the post-flush request one by one.
  It means that the request_queue is stopped automatically by
  the block-layer until drivers complete each sequence.

o dm-core
  For the barrier I/O, treats it as a normal I/O, so no additional
  code is needed.

  For the pre/post-flush request, flushes caches by the followings:
    1. Make the number of empty barrier requests required by target's
       num_flush_requests, and map them (dm_rq_barrier()).
    2. Waits for the mapped barriers to complete (dm_rq_barrier()).
       If error has occurred, save the error value to md->barrier_error
       (dm_end_request()).
       (*) Basically, the first reported error is taken.
           But -EOPNOTSUPP supersedes any error and DM_ENDIO_REQUEUE
           follows.
    3. Requeue the pre/post-flush request if the error value is
       DM_ENDIO_REQUEUE.  Otherwise, completes with the error value
       (dm_rq_barrier_work()).
  The pre/post-flush work above is done in the kernel thread (kdmflush)
  context, since memory allocation which might sleep is needed in
  dm_rq_barrier() but sleep is not allowed in dm_request_fn(), which is
  an irq-disabled context.
  Also, clones of the pre/post-flush request share an original, so
  such clones can't be completed using the softirq context.
  Instead, complete them in the context of underlying device drivers.
  It should be safe since there is no I/O dispatching during
  the completion of such clones.

  For suspend, the workqueue of kdmflush needs to be flushed after
  the request_queue has been stopped.  Otherwise, the next flush work
  can be kicked even after the suspend completes.

TARGET INTERFACE

No new interface is added.
Just use the existing num_flush_requests in struct target_type
as same as bio-based dm.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:18 +00:00
Kiyoshi Ueda 980691e5f3 dm: move dm_end_request
This patch moves dm_end_request() to make the next patch more readable.
No functional change.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:17 +00:00
Kiyoshi Ueda 11a68244e1 dm: refactor request based completion functions
This patch factors out the clone completion code, dm_done(),
from dm_softirq_done() in preparation for a subsequent patch.
No functional change.

dm_done() will be used in barrier completion, which can't use and
doesn't need softirq.  The softirq_done callback needs to get a clone
from an original request but it can't in the case of barrier, where
an original request is shared by multiple clones.  On the other hand,
the completion of barrier clones doesn't involve re-submitting requests,
which was the primary reason of the need for softirq.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:17 +00:00
Kiyoshi Ueda b4324feeae dm: use md pending for in flight IO counting
This patch changes the counter for the number of in_flight I/Os
to md->pending from q->in_flight in preparation for a later patch.
No functional change.

Request-based dm used q->in_flight to count the number of in-flight
clones assuming the counter is always incremented for an in-flight
original request and original:clone is 1:1 relationship.
However, it this no longer true for barrier requests.
So use md->pending to count the number of in-flight clones.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:16 +00:00
Kiyoshi Ueda 9f518b27cf dm: simplify request based suspend
The semantics of bio-based dm were changed recently in the case of
suspend with "--nolockfs" but without "--noflush".
Before 2.6.30, I/Os submitted before the suspend invocation were always
flushed.  From 2.6.30 onwards, I/Os submitted before the suspend
invocation might not be flushed.  (For details, see
http://marc.info/?t=123994433400003&r=1&w=2)

This patch brings the behaviour of request-based dm into line with
bio-based dm, simplifying the code and preparing for a subsequent patch
that will wait for all in_flight I/Os to complete without stopping
request_queue and use dm_wait_for_completion() for it.

This change in semantics simplifies the suspend code as follows:
  o Suspend is implemented as stopping request_queue
    in request-based dm, and all I/Os are queued in the request_queue
    even after suspend is invoked.
  o In the old semantics, we had to track whether I/Os were
    queued before or after the suspend invocation, so a special
    barrier-like request called 'suspend marker' was introduced.
  o With the new semantics, we don't need to flush any I/O
    so we can remove the marker and the code related to the marker
    handling and I/O flushing.

After removing this codes, the suspend sequence is now:
  1. Flush all I/Os by lock_fs() if needed.
  2. Stop dispatching any I/O by stopping the request_queue.
  3. Wait for all in-flight I/Os to be completed or requeued.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:16 +00:00
Kiyoshi Ueda 6facdaff22 dm: abstract clone_rq
This patch factors out the request cloning code in dm_prep_fn()
as clone_rq().  No functional change.

This patch is a preparation for a later patch in this series which needs to
make clones from an original barrier request.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:15 +00:00
Kiyoshi Ueda 0888564393 dm: pass gfp_mask to alloc_rq_tio
This patch adds the gfp_mask argument to alloc_rq_tio().
No functional change.

This patch is a preparation for a later patch in this series which needs to
allocate tio (for barrier I/O) with different allocation flag (GFP_NOIO) from
the one in the normal I/O code path.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:15 +00:00
Kiyoshi Ueda 598de40947 dm: use clone in map_request function
This patch changes the argument of map_request() to clone request
from original request.  No functional change.

This patch is a preparation for PATCH 9, which needs to use
map_request() for clones sharing an original barrier request.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:14 +00:00
Kiyoshi Ueda 90abb8c4ce dm: abstract dm_in_flight function
This patch adds md_in_flight() to get the number of in_flight I/Os.
No functional change.

This patch is a preparation for a later patch in this series, which
changes I/O counter to md->pending from q->in_flight in request-based dm.

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:13 +00:00
Mikulas Patocka 9ca170a3c0 dm kcopyd: accept zero size jobs
dm-kcopyd: accept zero-size jobs

This patch changes dm-kcopyd so that it accepts zero-size jobs and completes
them immediatelly via its completion thread.

It is needed for multisnapshots snapshot resizing. When we are writing to
a chunk beyond origin end, no copying is done. To simplify the code, we submit
an empty request to kcopyd and let kcopyd complete it. If we didn't submit
a request to kcopyd and called the completion routine immediatelly, it would
violate the principle that completion is called only from one thread and
it would need additional locking.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:13 +00:00
Mike Snitzer c26655ca3c dm snapshot: track suspended state in target
Keep track of whether or not the device is suspended within the snapshot
target module, the same as we do in dm-raid1.

We will use this later to enforce the correct sequence of ioctls to
transfer the in-core exceptions from a snapshot target instance in
one table to a replacement one capable of merging them back
into the origin.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:12 +00:00
Mike Snitzer fc56f6fbcc dm snapshot: move cow ref from exception store to snap core
Store the reference to the snapshot cow device in the core snapshot
code instead of each exception store.  It can be accessed through the
new function dm_snap_cow().  Exception stores should each now maintain a
reference to their parent snapshot struct.

This is cleaner and makes part of the forthcoming snapshot merge code simpler.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
2009-12-10 23:52:12 +00:00
Mike Snitzer 985903bb3a dm snapshot: add allocated metadata to snapshot status
Add number of sectors used by metadata to the end of the snapshot's status
line.

Renamed dm_exception_store_type's 'fraction_full' to 'usage'.  Renamed
arguments to be clearer about what is being returned.  Also added
'metadata_sectors'.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:11 +00:00
Jon Brassow 3510cb94ff dm snapshot: rename exception functions
Rename exception functions.  Preparing to pull them out of
dm-snap.c for broader use.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:11 +00:00
Jon Brassow 191437a53c dm snapshot: rename exception_table to dm_exception_table
Rename exception_table for broader use outside dm-snap.c

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:10 +00:00
Jon Brassow 1d4989c858 dm snapshot: rename dm_snap_exception to dm_exception
The exception structure is not necessarily just a snapshot
element (especially after we pull it out of dm-snap.c).

Renaming appropriately.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:10 +00:00
Jon Brassow d32a6ea65f dm snapshot: consolidate insert exception functions
Consolidate the insert_*exception functions.  'insert_completed_exception'
already contains all the logic to handle 'insert_exception' (via
check for a hash_shift of 0), so remove redundant function.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:09 +00:00
Mikulas Patocka 7e201b3513 dm snapshot: abstract minimum_chunk_size fn
The origin needs to find minimum chunksize of all snapshots.  This logic is
moved to a separate function because it will be used at another place in
the snapshot merge patches.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:08 +00:00
Mikulas Patocka 102c6ddb1d dm snapshot: simplify sector_to_chunk expression
Removed unnecessary 'and' masking: The right shift discards the lower
bits so there is no need to clear them.

(A later patch needs this change to support a 32-bit chunk_mask.)

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:08 +00:00
Jon Brassow f5acc83428 dm snapshot: avoid else clause in persistent_read_metadata
Minor code touch-up.  We don't need the 'else'.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:07 +00:00
Roel Kluin a518b86d0b dm ioctl: prefer strlcpy over strncpy
strlcpy() will always null terminate the string.

    The code should already guarantee this as the last bytes are already
    NULs and the string lengths were restricted before being stored in
    hc.  Removing the '-1' becomes necessary so strlcpy() doesn't
    lose the last character of a maximum-length string.
	- agk

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:07 +00:00
Mikulas Patocka 5339fc2d47 dm raid1: explicitly initialise bio_lists
Explicitly initialize bio lists instead of relying on kzalloc.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:06 +00:00
Mikulas Patocka 929be8fcb4 dm raid1: hold all write bios when leg fails
Hold all write bios when leg fails and errors are handled

When using a userspace daemon such as dmeventd to handle errors, we must
delay completing  bios until it has done its job.
This patch prevents the following race:
  - primary leg fails
  - write "1" fail, the write is held, secondary leg is set default
  - write "2" goes straight to the secondary leg

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:06 +00:00
Mikulas Patocka 60f355ead3 dm raid1: hold write bios when errors are handled
Hold all write bios when errors are handled.

Previously the failures list was used only when handling errors with
a userspace daemon such as dmeventd.  Now, it is always used for all bios.
The regions where some writes failed must be marked as nosync. This can only
be done in process context (i.e. in raid1 workqueue), not in the
write_callback function.

Previously the write would succeed if writing to at least one leg
succeeded.  This is wrong because data from the failed leg may be
replicated to the correct leg.  Now, if using a userspace daemon, the
write with some failures will be held until the daemon has done its job
and reconfigured the array.  If not using a daemon, the write still
succeeds if at least one leg succeeds. This is bad, but it is consistent
with current behavior.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:05 +00:00
Mikulas Patocka c58098be97 dm raid1: remove bio_endio from dm_rh_mark_nosync
Move bio completion out of dm_rh_mark_nosync in preparation for the
next patch.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:05 +00:00
Mikulas Patocka 87968ddd2f dm raid1: abstract get_valid_mirror function
Move the logic to get a valid mirror leg into a function for re-use
in a later patch.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:04 +00:00
Mikulas Patocka 0f398a8403 dm raid1: use hold framework in do_failures
Use the hold framework in do_failures.

This patch doesn't change the bio processing logic, it just simplifies
failure handling and avoids periodically polling the failures list.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:04 +00:00
Mikulas Patocka 0478850768 dm raid1: add framework to hold bios during suspend
Add framework to delay bios until a suspend and then resubmit them with
either DM_ENDIO_REQUEUE (if the suspend was noflush) or complete them
with -EIO.  I/O barrier support will use this.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Tested-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:03 +00:00
Mikulas Patocka 64b30c46e8 dm raid1: report flush errors separately in status
Report flush errors as 'F' instead of 'D' for log and mirror devices.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:02 +00:00
Mikulas Patocka c0da3748b9 dm raid1: implement mirror_flush
Implement flush callee. It uses dm_io to send zero-size barrier synchronously
and concurrently to all the mirror legs.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:02 +00:00
Mikulas Patocka 076010e2e6 dm log: use flush callback fn
Call the flush callback from the log.

If flush failed, we have no alternative but to mark the whole log as dirty.
Also we set the variable flush_failed to prevent any bits ever being marked as
clean again.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:01 +00:00
Mikulas Patocka 87a8f240e9 dm log: add flush callback fn
Introduce a callback pointer from the log to dm-raid1 layer.

Before some region is set as "in-sync", we need to flush hardware cache on
all the disks. But the log module doesn't have access to the mirror_set
structure. So it will use this callback.

So far the callback is unused, it will be used in further patches.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:01 +00:00
Mikulas Patocka 5adc78d0d2 dm log: introduce flush_failed variable
Introduce "flush failed" variable.  When a flush before clearing a bit
in the log fails, we don't know anything about which which regions are
in-sync and which not.

So we need to set all regions as not-in-sync and set the variable
"flush_failed" to prevent setting the in-sync bit in the future.

A target reload is the only way to get out of this situation.

The variable will be set in following patches.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:00 +00:00
Mikulas Patocka 20a34a8ecc dm log: add flush_header function
Introduce flush_header and use it to flush the log device.

Note that we don't have to flush if all the regions transition
from "dirty" to "clean" state.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:52:00 +00:00
Mikulas Patocka b09acf1aa7 dm raid1: split touched state into two
Split the variable "touched" into two, "touched_dirtied" and
"touched_cleaned", set when some region was dirtied or cleaned.

This will be used to optimize flushes.

After a transition from "dirty" to "clean" state we don't have flush hardware
cache on the log device. After a transition from "clean" to "dirty" the cache
must be flushed.

Before a transition from "clean" to "dirty" state we don't have to flush all
the raid legs. Before a transition from "dirty" to "clean" we must flush all
the legs to make sure that they are really in sync.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:59 +00:00
Mikulas Patocka 4184153f9e dm raid1: support flush
Flush support for dm-raid1.

When it receives an empty barrier, submit it to all the devices via dm-io.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:59 +00:00
Mikulas Patocka f1e5398746 dm io: remove extra bi_io_vec region hack
Remove the hack where we allocate an extra bi_io_vec to store additional
private data.  This hack prevents us from supporting barriers in
dm-raid1 without first making another little block layer change.
Instead of doing that, this patch eliminates the bi_io_vec abuse by
storing the region number directly in the low bits of bi_private.

We need to store two things for each bio, the pointer to the main io
structure and, if parallel writes were requested, an index indicating
which of these writes this bio belongs to.  There can be at most
BITS_PER_LONG regions - 32 or 64.

The index (region number) was stored in the last (hidden) bio vector and
the pointer to struct io was stored in bi_private.

This patch now aligns "struct io" on BITS_PER_LONG bytes and stores the
region number in the low BITS_PER_LONG bits of bi_private.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:58 +00:00
Mikulas Patocka 952b355760 dm io: use slab for struct io
Allocate "struct io" from a slab.

This patch changes dm-io, so that "struct io" is allocated from a slab cache.
It used to be allocated with kmalloc. Allocating from a slab will be needed
for the next patch, because it requires a special alignment of "struct io"
and kmalloc cannot meet this alignment.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:57 +00:00
Milan Broz 542da31766 dm crypt: make wipe message also wipe essiv key
The "wipe key" message is used to wipe the volume key from memory
temporarily, for example when suspending to RAM.

But the initialisation vector in ESSIV mode is calculated from the
hashed volume key, so the wipe message should wipe this IV key too and
reinitialise it when the volume key is reinstated.

This patch adds an IV wipe method called from a wipe message callback.
ESSIV is then reinitialised using the init function added by the
last patch.

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:57 +00:00
Milan Broz b95bf2d3d5 dm crypt: separate essiv allocation from initialisation
This patch separates the construction of IV from its initialisation.
(For ESSIV it is a hash calculation based on volume key.)

Constructor code now preallocates hash tfm and salt array
and saves it in a private IV structure.

The next patch requires this to reinitialise the wiped IV
without reallocating memory when resuming a suspended device.

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:56 +00:00
Milan Broz 5861f1be00 dm crypt: restructure essiv error path
Use kzfree for salt deallocation because it is derived from the volume
key.  Use a common error path in ESSIV constructor.

Required by a later patch which fixes the way key material is wiped
from memory.

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:56 +00:00
Milan Broz 6047359277 dm crypt: move private iv fields to structs
Define private structures for IV so it's easy to add further attributes
in a following patch which fixes the way key material is wiped from
memory.  Also move ESSIV destructor and remove unnecessary 'status'
operation.

There are no functional changes in this patch.

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:55 +00:00
Milan Broz 0b4309581b dm crypt: make wipe message also wipe tfm key
The "wipe key" message is used to wipe a volume key from memory
temporarily, for example when suspending to RAM.

There are two instances of the key in memory (inside crypto tfm)
but only one got wiped.  This patch wipes them both.

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:55 +00:00
Mikulas Patocka 8e87b9b81b dm snapshot: cope with chunk size larger than origin
Under some special conditions the snapshot hash_size is calculated as zero.
This patch instead sets a minimum value of 64, the same as for the
pending exception table.

rounddown_pow_of_two(0) is an undefined operation (it expands to shift
by -1).  init_exception_table with an argument of 0 would fail with -ENOMEM.

The way to trigger the problem is to create a snapshot with a chunk size
that is larger than the origin device.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:54 +00:00
Mikulas Patocka 94e76572b5 dm snapshot: only take lock for statustype info not table
Take snapshot lock only for STATUSTYPE_INFO, not STATUSTYPE_TABLE.

Commit 4c6fff445d
(dm-snapshot-lock-snapshot-while-supplying-status.patch)
introduced this use of the lock, but userspace applications using
libdevmapper have been found to request STATUSTYPE_TABLE while the device
is suspended and the lock is already held, leading to deadlock.  Since
the lock is not necessary in this case, don't try to take it.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:53 +00:00
Milan Broz d2bb7df8ca dm: sysfs add empty release function to avoid debug warning
This patch just removes an unnecessary warning:
 kobject: 'dm': does not have a release() function,
 it is broken and must be fixed.

The kobject is embedded in mapped device struct, so
code does not need to release memory explicitly here.

Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:53 +00:00
Julia Lawall 613978f871 dm exception store: free tmp_store on persistent flag error
Error handling code following a kmalloc should free the allocated data.

Cc: stable@kernel.org
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:52 +00:00
Mikulas Patocka 6076905b5e dm: avoid _hash_lock deadlock
Fix a reported deadlock if there are still unprocessed multipath events
on a device that is being removed.

_hash_lock is held during dev_remove while trying to send the
outstanding events.  Sending the events requests the _hash_lock
again in dm_copy_name_and_uuid.

This patch introduces a separate lock around regions that modify the
link to the hash table (dm_set_mdptr) or the name or uuid so that
dm_copy_name_and_uuid no longer needs _hash_lock.

Additionally, dm_copy_name_and_uuid can only be called if md exists
so we can drop the dm_get() and dm_put() which can lead to a BUG()
while md is being freed.

The deadlock:
 #0 [ffff8106298dfb48] schedule at ffffffff80063035
 #1 [ffff8106298dfc20] __down_read at ffffffff8006475d
 #2 [ffff8106298dfc60] dm_copy_name_and_uuid at ffffffff8824f740
 #3 [ffff8106298dfc90] dm_send_uevents at ffffffff88252685
 #4 [ffff8106298dfcd0] event_callback at ffffffff8824c678
 #5 [ffff8106298dfd00] dm_table_event at ffffffff8824dd01
 #6 [ffff8106298dfd10] __hash_remove at ffffffff882507ad
 #7 [ffff8106298dfd30] dev_remove at ffffffff88250865
 #8 [ffff8106298dfd60] ctl_ioctl at ffffffff88250d80
 #9 [ffff8106298dfee0] do_ioctl at ffffffff800418c4
#10 [ffff8106298dff00] vfs_ioctl at ffffffff8002fab9
#11 [ffff8106298dff40] sys_ioctl at ffffffff8004bdaf
#12 [ffff8106298dff80] tracesys at ffffffff8005d28d (via system_call)

Cc: stable@kernel.org
Reported-by: guy keren <choo@actcom.co.il>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-12-10 23:51:52 +00:00
Linus Torvalds 4ef58d4e2a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
  tree-wide: fix misspelling of "definition" in comments
  reiserfs: fix misspelling of "journaled"
  doc: Fix a typo in slub.txt.
  inotify: remove superfluous return code check
  hdlc: spelling fix in find_pvc() comment
  doc: fix regulator docs cut-and-pasteism
  mtd: Fix comment in Kconfig
  doc: Fix IRQ chip docs
  tree-wide: fix assorted typos all over the place
  drivers/ata/libata-sff.c: comment spelling fixes
  fix typos/grammos in Documentation/edac.txt
  sysctl: add missing comments
  fs/debugfs/inode.c: fix comment typos
  sgivwfb: Make use of ARRAY_SIZE.
  sky2: fix sky2_link_down copy/paste comment error
  tree-wide: fix typos "couter" -> "counter"
  tree-wide: fix typos "offest" -> "offset"
  fix kerneldoc for set_irq_msi()
  spidev: fix double "of of" in comment
  comment typo fix: sybsystem -> subsystem
  ...
2009-12-09 19:43:33 -08:00
Linus Torvalds 382f51fe2f Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
  [SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
  [SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
  [SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
  [SCSI] zfcp: Update FSF error reporting
  [SCSI] zfcp: Improve ELS ADISC handling
  [SCSI] zfcp: Simplify handling of ct and els requests
  [SCSI] zfcp: Remove ZFCP_DID_MASK
  [SCSI] zfcp: Move WKA port to zfcp FC code
  [SCSI] zfcp: Use common code definitions for FC CT structs
  [SCSI] zfcp: Use common code definitions for FC ELS structs
  [SCSI] zfcp: Update FCP protocol related code
  [SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
  [SCSI] zfcp: Assign scheduled work to driver queue
  [SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
  [SCSI] zfcp: Implement module unloading
  [SCSI] zfcp: Merge trace code for fsf requests in one function
  [SCSI] zfcp: Access ports and units with container_of in sysfs code
  [SCSI] zfcp: Remove suspend callback
  [SCSI] zfcp: Remove global config_mutex
  [SCSI] zfcp: Replace local reference counting with common kref
  ...
2009-12-09 19:42:25 -08:00
Linus Torvalds 1557d33007 Merge git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
  security/tomoyo: Remove now unnecessary handling of security_sysctl.
  security/tomoyo: Add a special case to handle accesses through the internal proc mount.
  sysctl: Drop & in front of every proc_handler.
  sysctl: Remove CTL_NONE and CTL_UNNUMBERED
  sysctl: kill dead ctl_handler definitions.
  sysctl: Remove the last of the generic binary sysctl support
  sysctl net: Remove unused binary sysctl code
  sysctl security/tomoyo: Don't look at ctl_name
  sysctl arm: Remove binary sysctl support
  sysctl x86: Remove dead binary sysctl support
  sysctl sh: Remove dead binary sysctl support
  sysctl powerpc: Remove dead binary sysctl support
  sysctl ia64: Remove dead binary sysctl support
  sysctl s390: Remove dead sysctl binary support
  sysctl frv: Remove dead binary sysctl support
  sysctl mips/lasat: Remove dead binary sysctl support
  sysctl drivers: Remove dead binary sysctl support
  sysctl crypto: Remove dead binary sysctl support
  sysctl security/keys: Remove dead binary sysctl support
  sysctl kernel: Remove binary sysctl logic
  ...
2009-12-08 07:38:50 -08:00
Jiri Kosina d014d04386 Merge branch 'for-next' into for-linus
Conflicts:

	kernel/irq/chip.c
2009-12-07 18:36:35 +01:00
Chandra Seetharaman 3ae31f6a7b [SCSI] scsi_dh: Change the scsidh_activate interface to be asynchronous
Make scsi_dh_activate() function asynchronous, by taking in two additional
parameters, one is the callback function and the other is the data to call
the callback function with.

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-12-04 12:00:46 -06:00
NeilBrown d0e260782c md: revert incorrect fix for read error handling in raid1.
commit 4706b349f was a forward port of a fix that was needed
for SLES10.  But in fact it is not needed in mainline because
the earlier commit dd00a99e7a fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction.  If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.

After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
2009-12-01 17:30:59 +11:00
Eric W. Biederman 6d4561110a sysctl: Drop & in front of every proc_handler.
For consistency drop & in front of every proc_handler.  Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.

Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
2009-11-18 08:37:40 -08:00
Eric W. Biederman bb9074ff58 Merge commit 'v2.6.32-rc7'
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
2009-11-17 01:01:34 -08:00
NeilBrown c148ffdcda md/raid5: Allow dirty-degraded arrays to be assembled when only party is degraded.
Normally is it not safe to allow a raid5 that is both dirty and
degraded to be assembled without explicit request from that admin, as
it can cause hidden data corruption.
This is because 'dirty' means that the parity cannot be trusted, and
'degraded' means that the parity needs to be used.

However, if the device that is missing contains only parity, then
there is no issue and assembly can continue.
This particularly applies when a RAID5 is being converted to a RAID6
and there is an unclean shutdown while the conversion is happening.

So check for whether the degraded space only contains parity, and
in that case, allow the assembly.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-11-13 17:47:00 +11:00
NeilBrown 7ef90146a1 Don't unconditionally set in_sync on newly added device in raid5_reshape
When a reshape finds that it can add spare devices into the array,
those devices might already be 'in_sync' if they are beyond the old
size of the array, or they might not if they are within the array.

The first case happens when we change an N-drive RAID5 to an
N+1-drive RAID5.
The second happens when we convert an N-drive RAID5 to an
N+1-drive RAID6.

So set the flag more carefully.
Also, ->recovery_offset is only meaningful when the flag is clear,
so only set it in that case.

This change needs the preceding two to ensure that the non-in_sync
device doesn't get evicted from the array when it is stopped, in the
case where v0.90 metadata is used.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-11-13 17:40:51 +11:00
NeilBrown 0261cd9f1c md: allow v0.91 metadata to record devices as being active but not in-sync.
This is a combination that didn't really make sense before.
However when a reshape is converting e.g. raid5 -> raid6, the extra
device is not fully in-sync, but is certainly active and contains
important data.
So allow that start to be meaningful and in particular get
the 'recovery_offset' value (which is needed for any non-in-sync
active device) from the reshape_position.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-11-13 17:40:48 +11:00
Eric W. Biederman 894d249115 sysctl drivers: Remove dead binary sysctl support
Now that sys_sysctl is a wrapper around /proc/sys all of
the binary sysctl support elsewhere in the tree is
dead code.

Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Neil Brown <neilb@suse.de>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de> for drivers/char/hpet.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
2009-11-12 02:04:58 -08:00
NeilBrown 5e8651060c md: factor out updating of 'recovery_offset'.
Each device has its own 'recovery_offset' showing how far
recovery has progressed on the device.
As the only real significance of this is that fact that it can
be stored in the metadata and recovered at restart, and as
only 1.x metadata can do this, we were only updating
'recovery_offset' to 'curr_resync_completed' when updating
v1.x metadata.
But this is wrong, and we will shortly make limited use of this
field in v0.90 metadata.

So move the update into common code.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-11-12 12:08:04 +11:00
Dirk Hohndel 06fe9fb418 tree-wide: fix a very frequent spelling mistake
something-bility is spelled as something-blity
so a grep for 'blit' would find these lines

this is so trivial that I didn't split it by subsystem / copy
additional maintainers - all changes are to comments
The only purpose is to get fewer false positives when grepping
around the kernel sources.

Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-11-09 09:40:54 +01:00
NeilBrown 8dee721146 md/raid5: make sure curr_sync_completes is uptodate when reshape starts
This value is visible through sysfs and is used by mdadm
when it manages a reshape (backing up data that is about to be
rearranged).  So it is important that it is always correct.
Current it does not get updated properly when a reshape
starts which can cause problems when assembling an array
that is in the middle of being reshaped.

This is suitable for 2.6.31.y stable kernels.

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-11-06 14:59:29 +11:00
NeilBrown 24395a85d8 md: don't clear endpoint for resync when resync is interrupted.
If a 'sync_max' has been set (via sysfs), it is wrong to clear it
until a resync (or reshape or recovery ...) actually reached that
point.
So if a resync is interrupted (e.g. by device failure),
leave 'resync_max' unchanged.

This is particularly important for 'reshape' operations that do not
change the size of the array.  For such operations mdadm needs to
monitor the reshape taking rolling backups of the section being
reshaped.  If resync_max gets cleared, the reshape can get ahead of
mdadm and then the backups that mdadm creates are useless.

This is suitable for 2.6.31.y stable kernels.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-11-06 14:59:27 +11:00
Linus Torvalds bf699c9bac Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
  async_tx: fix asynchronous raid6 recovery for ddf layouts
  async_pq: rename scribble page
  async_pq: kill a stray dma_map() call and other cleanups
  md/raid6: kill a gcc-4.0.1 'uninitialized variable' warning
  raid6/async_tx: handle holes in block list in async_syndrome_val
  md/async: don't pass a memory pointer as a page pointer.
  md: Fix handling of raid5 array which is being reshaped to fewer devices.
  md: fix problems with RAID6 calculations for DDF.
  md/raid456: downlevel multicore operations to raid_run_ops
  md: drivers/md/unroll.pl replaced with awk analog
  md: remove clumsy usage of do_sync_mapping_range from bitmap code
  md: raid1/raid10: handle allocation errors during array setup.
  md/raid5: initialize conf->device_lock earlier
  md/raid1/raid10: add a cond_resched
  Revert "md: do not progress the resync process if the stripe was blocked"
2009-10-31 12:12:19 -07:00
David Woodhouse e5d84970a5 async_tx: Move ASYNC_RAID6_TEST option to crypto/async_tx/, fix dependencies
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-10-29 16:41:49 +00:00
David Woodhouse f5e70d0fe3 md: Factor out RAID6 algorithms into lib/
We'll want to use these in btrfs too.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-10-29 14:38:47 +00:00
Dan Williams 6629542e79 md/raid6: kill a gcc-4.0.1 'uninitialized variable' warning
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-10-19 18:09:41 -07:00
Mikulas Patocka c1cc65caa1 dm snapshot: allow chunk size to be less than page size
Allow the snapshot chunk size to be smaller than the page size
The code is now capable of handling this due to some previous
fixes and enhancements.

As the page size varies between computers, prior to this patch,
the chunk size of a snapshot dictated which machines could read it:
Snapshots created on one machine might not be readable on another.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:22 +01:00
Mikulas Patocka df96eee679 dm snapshot: use unsigned integer chunk size
Use unsigned integer chunk size.

Maximum chunk size is 512kB, there won't ever be need to use 4GB chunk size,
so the number can be 32-bit. This fixes compiler failure on 32-bit systems
with large block devices.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:17 +01:00
Mikulas Patocka 4c6fff445d dm snapshot: lock snapshot while supplying status
This patch locks the snapshot when returning status.  It fixes a race
when it could return an invalid number of free chunks if someone
was simultaneously modifying it.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:16 +01:00
Mikulas Patocka 0e8c4e4e3e dm exception store: fix failed set_chunk_size error path
Properly close the device if failing because of an invalid chunk size.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:16 +01:00
Mikulas Patocka 3f2412dc85 dm snapshot: require non zero chunk size by end of ctr
If we are creating snapshot with memory-stored exception store, fail if
the user didn't specify chunk size. Zero chunk size would probably crash
a lot of places in the rest of snapshot code.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:16 +01:00
Kiyoshi Ueda f88fb98118 dm: dec_pending needs locking to save error value
Multiple instances of dec_pending() can run concurrently so a lock is
needed when it saves the first error code.

I have never experienced actual problem without locking and just found
this during code inspection while implementing the barrier support
patch for request-based dm.

This patch adds the locking.
I've done compile, boot and basic I/O testings.

Cc: stable@kernel.org
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:15 +01:00
Zdenek Kabelac 03022c54b9 dm: add missing del_gendisk to alloc_dev error path
Add missing del_gendisk() to error path when creation of workqueue fails.
Otherwice there is a resource leak and following warning is shown:

WARNING: at fs/sysfs/dir.c:487 sysfs_add_one+0xc5/0x160()
sysfs: cannot create duplicate filename '/devices/virtual/block/dm-0'

Cc: stable@kernel.org
Signed-off-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:15 +01:00
Andrew Morton bca915aae8 dm log: userspace fix incorrect luid cast in userspace_ctr
mips:

drivers/md/dm-log-userspace-base.c: In function `userspace_ctr':
drivers/md/dm-log-userspace-base.c:159: warning: cast from pointer to integer of different size

Cc: stable@kernel.org
Cc: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:15 +01:00
Jonathan Brassow 034a186d29 dm snapshot: free exception store on init failure
While initializing the snapshot module, if we fail to register
the snapshot target then we must back-out the exception store
module initialization.

Cc: stable@kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:14 +01:00
Mikulas Patocka 6d45d93ead dm snapshot: sort by chunk size to fix race
Avoid a race causing corruption when snapshots of the same origin have
different chunk sizes by sorting the internal list of snapshots by chunk
size, largest first.
  https://bugzilla.redhat.com/show_bug.cgi?id=182659

For example, let's have two snapshots with different chunk sizes. The
first snapshot (1) has small chunk size and the second snapshot (2) has
large chunk size.  Let's have chunks A, B, C in these snapshots:
snapshot1: ====A====   ====B====
snapshot2: ==========C==========

(Chunk size is a power of 2. Chunks are aligned.)

A write to the origin at a position within A and C comes along. It
triggers reallocation of A, then reallocation of C and links them
together using A as the 'primary' exception.

Then another write to the origin comes along at a position within B and
C.  It creates pending exception for B.  C already has a reallocation in
progress and it already has a primary exception (A), so nothing is done
to it: B and C are not linked.

If the reallocation of B finishes before the reallocation of C, because
there is no link with the pending exception for C it does not know to
wait for it and, the second write is dispatched to the origin and causes
data corruption in the chunk C in snapshot2.

To avoid this situation, we maintain snapshots sorted in descending
order of chunk size.  This leads to a guaranteed ordering on the links
between the pending exceptions and avoids the problem explained above -
both A and B now get linked to C.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-10-16 23:18:14 +01:00
NeilBrown 5dd33c9a4c md/async: don't pass a memory pointer as a page pointer.
md/raid6 passes a list of 'struct page *' to the async_tx routines,
which then either DMA map them for offload, or take the page_address
for CPU based calculations.

For RAID6 we sometime leave 'blanks' in the list of pages.
For CPU based calcs, we want to treat theses as a page of zeros.
For offloaded calculations, we simply don't pass a page to the
hardware.

Currently the 'blanks' are encoded as a pointer to
raid6_empty_zero_page.  This is a 4096 byte memory region, not a
'struct page'.  This is mostly handled correctly but is rather ugly.

So change the code to pass and expect a NULL pointer for the blanks.
When taking page_address of a page, we need to check for a NULL and
in that case use raid6_empty_zero_page.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 16:40:25 +11:00
NeilBrown 5e5e3e78ed md: Fix handling of raid5 array which is being reshaped to fewer devices.
When a raid5 (or raid6) array is being reshaped to have fewer devices,
conf->raid_disks is the latter and hence smaller number of devices.
However sometimes we want to use a number which is the total number of
currently required devices - the larger of the 'old' and 'new' sizes.
Before we implemented reducing the number of devices, this was always
'new' i.e. ->raid_disks.
Now we need max(raid_disks, previous_raid_disks) in those places.

This particularly affects assembling an array that was shutdown while
in the middle of a reshape to fewer devices.

md.c needs a similar fix when interpreting the md metadata.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 16:35:30 +11:00
NeilBrown e4424fee18 md: fix problems with RAID6 calculations for DDF.
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 16:27:34 +11:00
Dan Williams 417b8d4ac8 md/raid456: downlevel multicore operations to raid_run_ops
The percpu conversion allowed a straightforward handoff of stripe
processing to the async subsytem that initially showed some modest gains
(+4%).  However, this model is too simplistic and leads to stripes
bouncing between raid5d and the async thread pool for every invocation
of handle_stripe().  As reported by Holger this can fall into a
pathological situation severely impacting throughput (6x performance
loss).

By downleveling the parallelism to raid_run_ops the pathological
stripe_head bouncing is eliminated.  This version still exhibits an
average 11% throughput loss for:

	mdadm --create /dev/md0 /dev/sd[b-q] -n 16 -l 6
	echo 1024 > /sys/block/md0/md/stripe_cache_size
	dd if=/dev/zero of=/dev/md0 bs=1024k count=2048

...but the results are at least stable and can be used as a base for
further multicore experimentation.

Reported-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 16:25:22 +11:00
Vladimir Dronnikov dce3a7a42d md: drivers/md/unroll.pl replaced with awk analog
drivers/md/unroll.pl replaced by awk script to drop build-time
dependency on perl

Signed-off-by: Vladimir Dronnikov <dronnikov@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 16:25:19 +11:00
NeilBrown ae8fa2831b md: remove clumsy usage of do_sync_mapping_range from bitmap code
and replace with vfs_fsync which is much neater (but wasn't exported,
or even in existence at the time the code was written).

Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 15:56:01 +11:00
NeilBrown ed9bfdf1a4 md: raid1/raid10: handle allocation errors during array setup.
Both raid1 and raid10 create a mempool during startup.
If the 'alloc' function for this mempool fails, unplug_slaves
is called.
If that happens when the pool is being initialised, unplug_slaves
will try to use the 'conf' structure that isn't filled in yet, and
badness will happen.

So ensure that unplug_slaves doesn't get called unless we know
that the conf structure if fully initialised.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 15:55:44 +11:00
Dan Williams f5efd45ae5 md/raid5: initialize conf->device_lock earlier
Deallocating a raid5_conf_t structure requires taking 'device_lock'.
Ensure it is initialized before it is used, i.e. initialize the lock
before attempting any further initializations that might fail.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 15:55:38 +11:00
NeilBrown 1d9d52416c md/raid1/raid10: add a cond_resched
During 'check' of a raid1 or raid10 it is possible for the management
thread to spend a lot of time running 'memcmp' on blocks from
different devices, so make sure the thread has a chance to schedule.
raid5d already has a cond_resched (in process_stripe).

Reported-By: Lee Howard <faxguy@howardsilvan.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 15:55:32 +11:00
NeilBrown 1442577bf6 Revert "md: do not progress the resync process if the stripe was blocked"
This reverts commit df10cfbc4d.

This patch was based on a misunderstanding and risks introducing a busy-wait loop.
So revert it.

Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-10-16 15:55:25 +11:00
Nikanth Karthikesan 316d315bff block: Seperate read and write statistics of in_flight requests v2
Commit a9327cac44 added seperate read
and write statistics of in_flight requests. And exported the number
of read and write requests in progress seperately through sysfs.

But  Corrado Zoccolo <czoccolo@gmail.com> reported getting strange
output from "iostat -kx 2". Global values for service time and
utilization were garbage. For interval values, utilization was always
100%, and service time is higher than normal.

So this was reverted by commit 0f78ab9899

The problem was in part_round_stats_single(), I missed the following:
        if (now == part->stamp)
                return;

-       if (part->in_flight) {
+       if (part_in_flight(part)) {
                __part_stat_add(cpu, part, time_in_queue,
                                part_in_flight(part) * (now - part->stamp));
                __part_stat_add(cpu, part, io_ticks, (now - part->stamp));

With this chunk included, the reported regression gets fixed.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>

--
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-06 20:16:55 +02:00
Linus Torvalds 58e57fbd1c Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (41 commits)
  Revert "Seperate read and write statistics of in_flight requests"
  cfq-iosched: don't delay async queue if it hasn't dispatched at all
  block: Topology ioctls
  cfq-iosched: use assigned slice sync value, not default
  cfq-iosched: rename 'desktop' sysfs entry to 'low_latency'
  cfq-iosched: implement slower async initiate and queue ramp up
  cfq-iosched: delay async IO dispatch, if sync IO was just done
  cfq-iosched: add a knob for desktop interactiveness
  Add a tracepoint for block request remapping
  block: allow large discard requests
  block: use normal I/O path for discard requests
  swapfile: avoid NULL pointer dereference in swapon when s_bdev is NULL
  fs/bio.c: move EXPORT* macros to line after function
  Add missing blk_trace_remove_sysfs to be in pair with blk_trace_init_sysfs
  cciss: fix build when !PROC_FS
  block: Do not clamp max_hw_sectors for stacking devices
  block: Set max_sectors correctly for stacking devices
  cciss: cciss_host_attr_groups should be const
  cciss: Dynamically allocate the drive_info_struct for each logical drive.
  cciss: Add usage_count attribute to each logical drive in /sys
  ...
2009-10-04 12:39:14 -07:00
Jens Axboe 0f78ab9899 Revert "Seperate read and write statistics of in_flight requests"
This reverts commit a9327cac44.

Corrado Zoccolo <czoccolo@gmail.com> reports:

"with 2.6.32-rc1 I started getting the following strange output from
"iostat -kx 2":
Linux 2.6.31bisect (et2) 	04/10/2009 	_i686_	(2 CPU)

avg-cpu:  %user   %nice %system %iowait  %steal   %idle
          10,70    0,00    3,16   15,75    0,00   70,38

Device:         rrqm/s   wrqm/s     r/s     w/s    rkB/s    wkB/s
avgrq-sz avgqu-sz   await  svctm  %util
sda              18,22     0,00    0,67    0,01    14,77     0,02
43,94     0,01   10,53 39043915,03 2629219,87
sdb              60,89     9,68   50,79    3,04  1724,43    50,52
65,95     0,70   13,06 488437,47 2629219,87

avg-cpu:  %user   %nice %system %iowait  %steal   %idle
           2,72    0,00    0,74    0,00    0,00   96,53

Device:         rrqm/s   wrqm/s     r/s     w/s    rkB/s    wkB/s
avgrq-sz avgqu-sz   await  svctm  %util
sda               0,00     0,00    0,00    0,00     0,00     0,00
0,00     0,00    0,00   0,00 100,00
sdb               0,00     0,00    0,00    0,00     0,00     0,00
0,00     0,00    0,00   0,00 100,00

avg-cpu:  %user   %nice %system %iowait  %steal   %idle
           6,68    0,00    0,99    0,00    0,00   92,33

Device:         rrqm/s   wrqm/s     r/s     w/s    rkB/s    wkB/s
avgrq-sz avgqu-sz   await  svctm  %util
sda               0,00     0,00    0,00    0,00     0,00     0,00
0,00     0,00    0,00   0,00 100,00
sdb               0,00     0,00    0,00    0,00     0,00     0,00
0,00     0,00    0,00   0,00 100,00

avg-cpu:  %user   %nice %system %iowait  %steal   %idle
           4,40    0,00    0,73    1,47    0,00   93,40

Device:         rrqm/s   wrqm/s     r/s     w/s    rkB/s    wkB/s
avgrq-sz avgqu-sz   await  svctm  %util
sda               0,00     0,00    0,00    0,00     0,00     0,00
0,00     0,00    0,00   0,00 100,00
sdb               0,00     4,00    0,00    3,00     0,00    28,00
18,67     0,06   19,50 333,33 100,00

Global values for service time and utilization are garbage. For
interval values, utilization is always 100%, and service time is
higher than normal.

I bisected it down to:
[a9327cac44] Seperate read and write
statistics of in_flight requests
and verified that reverting just that commit indeed solves the issue
on 2.6.32-rc1."

So until this is debugged, revert the bad commit.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-10-04 21:04:38 +02:00
Philipp Reisner 24836479a1 dm/connector: Only process connector packages from privileged processes
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-02 10:54:10 -07:00
Philipp Reisner 18366b05a0 connector/dm: Fixed a compilation warning
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-02 10:54:04 -07:00
Philipp Reisner 7069331dbe connector: Provide the sender's credentials to the callback
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-02 10:54:01 -07:00
NeilBrown 4b3df5668c Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx into for-linus 2009-09-23 18:31:11 +10:00
Dmitry Monakhov 1ef04fefe2 md: raid-1/10: fix RW bits manipulation
Recently Jens has changed bio_rw_flagged() logic by following
commit 1f98a13f62. Now it returns
bool instead of int. This broke raid1/raid10 RW bits manipulation logic.
One of visible result is BUG_ON triggering due to empty barrier
here scsi_lib.c:1108 scsi_setup_fs_cmnd()

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:20:15 +10:00
NeilBrown f28f4e2728 md: remove unnecessary memset from multipath.
Recent commit bbba809e96
replaced mempool_create_kzalloc_pool with mempool_create_kmalloc_pool
plus a memset.
This memset is not needed (and we didn't need kzalloc in the first
place).
Ever field of the allocated structure (struct multipath_bh) is
initialised immediately except retry_list, and memset does not
initial a list_head anyway.

To remove the memset.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:16:31 +10:00
NeilBrown 3fa841d7e7 md: report device as congested when suspended
This should writeback from coming when the device is temporarily
suspended.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:10:29 +10:00
NeilBrown 0da3c6194e md: Improve name of threads created by md_register_thread
The management thread for raid4,5,6 arrays are all called
mdX_raid5, independent of the actual raid level, which is wrong and
can be confusion.

So change md_register_thread to use the name from the personality
unless no alternate name (like 'resync' or 'reshape') is given.

This is simpler and more correct.

Cc: Jinzc <zhenchengjin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:09:45 +10:00
NeilBrown ee305acef5 md: remove sparse warnings about lock context.
There was a real error here on a failure path where we
incorrectly call rcu_read_unlock.


Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:06:44 +10:00
NeilBrown a9f326ebf2 md: remove sparse waring "symbol xxx shadows an earlier one"
Rename some variable and remove some duplicate definitions
to avoid there warnings.  None of them are actual errors.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-09-23 18:06:41 +10:00
Linus Torvalds 342ff1a1b5 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
  trivial: fix typo in aic7xxx comment
  trivial: fix comment typo in drivers/ata/pata_hpt37x.c
  trivial: typo in kernel-parameters.txt
  trivial: fix typo in tracing documentation
  trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
  trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
  trivial: remove unnecessary semicolons
  trivial: Fix duplicated word "options" in comment
  trivial: kbuild: remove extraneous blank line after declaration of usage()
  trivial: improve help text for mm debug config options
  trivial: doc: hpfall: accept disk device to unload as argument
  trivial: doc: hpfall: reduce risk that hpfall can do harm
  trivial: SubmittingPatches: Fix reference to renumbered step
  trivial: fix typos "man[ae]g?ment" -> "management"
  trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
  trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
  trivial: fix missing printk space in amd_k7_smp_check
  trivial: fix typo s/ketymap/keymap/ in comment
  trivial: fix typo "to to" in multiple files
  trivial: fix typos in comments s/DGBU/DBGU/
  ...
2009-09-22 07:51:45 -07:00
Sage Weil bbba809e96 md: avoid use of broken kzalloc mempool
The kzalloc mempool does not re-zero items that have been used and then
returned to the pool.  Manually zero the allocated multipath_bh instead.

Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:35 -07:00
Alexey Dobriyan 83d5cde47d const: make block_device_operations const
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:25 -07:00
Anand Gadiyar 411c940385 trivial: fix typo "for for" in multiple files
trivial: fix typo "for for" in multiple files

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-09-21 15:14:54 +02:00
Kay Sievers e454cea20b Driver-Core: extend devnode callbacks to provide permissions
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.

This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 12:50:38 -07:00
Dan Williams 6c910a78e4 md/raid6: cleanup ops_run_compute6_2
Neil says:
	"It is correct as it stands, but the fact that every branch in
	 the 'if' part ends with a 'return' isn't immediately obvious,
	 so it is clearer if we are explicit about the if / then / else
	 structure."

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-09-16 12:24:54 -07:00
Dan Williams 2d6e4ecc87 md/raid6: eliminate BUG_ON with side effect
As pointed out by Neil it should be possible to build a driver with all
BUG_ON statements deleted.  It's bad form to have a BUG_ON with a side
effect.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-09-16 12:11:54 -07:00
Linus Torvalds 355bbd8cb8 Merge branch 'for-2.6.32' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.32' of git://git.kernel.dk/linux-2.6-block: (29 commits)
  block: use blkdev_issue_discard in blk_ioctl_discard
  Make DISCARD_BARRIER and DISCARD_NOBARRIER writes instead of reads
  block: don't assume device has a request list backing in nr_requests store
  block: Optimal I/O limit wrapper
  cfq: choose a new next_req when a request is dispatched
  Seperate read and write statistics of in_flight requests
  aoe: end barrier bios with EOPNOTSUPP
  block: trace bio queueing trial only when it occurs
  block: enable rq CPU completion affinity by default
  cfq: fix the log message after dispatched a request
  block: use printk_once
  cciss: memory leak in cciss_init_one()
  splice: update mtime and atime on files
  block: make blk_iopoll_prep_sched() follow normal 0/1 return convention
  cfq-iosched: get rid of must_alloc flag
  block: use interrupts disabled version of raise_softirq_irqoff()
  block: fix comment in blk-iopoll.c
  block: adjust default budget for blk-iopoll
  block: fix long lines in block/blk-iopoll.c
  block: add blk-iopoll, a NAPI like approach for block devices
  ...
2009-09-14 17:55:15 -07:00
Linus Torvalds 39695224bd Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (209 commits)
  [SCSI] fix oops during scsi scanning
  [SCSI] libsrp: fix memory leak in srp_ring_free()
  [SCSI] libiscsi, bnx2i: make bound ep check common
  [SCSI] libiscsi: add completion function for drivers that do not need pdu processing
  [SCSI] scsi_dh_rdac: changes for rdac debug logging
  [SCSI] scsi_dh_rdac: changes to collect the rdac debug information during the initialization
  [SCSI] scsi_dh_rdac: move the init code from rdac_activate to rdac_bus_attach
  [SCSI] sg: fix oops in the error path in sg_build_indirect()
  [SCSI] mptsas : Bump version to 3.04.12
  [SCSI] mptsas : FW event thread and scsi mid layer deadlock in SYNCHRONIZE CACHE command
  [SCSI] mptsas : Send DID_NO_CONNECT for pending IOs of removed device
  [SCSI] mptsas : PAE Kernel more than 4 GB kernel panic
  [SCSI] mptsas : NULL pointer on big endian systems causing Expander not to tear off
  [SCSI] mptsas : Sanity check for phyinfo is added
  [SCSI] scsi_dh_rdac: Add support for Sun StorageTek ST2500, ST2510 and ST2530
  [SCSI] pmcraid: PMC-Sierra MaxRAID driver to support 6Gb/s SAS RAID controller
  [SCSI] qla2xxx: Update version number to 8.03.01-k6.
  [SCSI] qla2xxx: Properly delete rports attached to a vport.
  [SCSI] qla2xxx: Correct various NPIV issues.
  [SCSI] qla2xxx: Correct qla2x00_eh_wait_on_command() to wait correctly.
  ...
2009-09-14 17:53:36 -07:00
Martin K. Petersen 3c5820c743 block: Optimal I/O limit wrapper
Implement blk_limits_io_opt() and make blk_queue_io_opt() a wrapper
around it. DM needs this to avoid poking at the queue_limits directly.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-09-14 08:24:52 +02:00
Nikanth Karthikesan a9327cac44 Seperate read and write statistics of in_flight requests
Currently, there is a single in_flight counter measuring the number of
requests in the request_queue. But some monitoring tools would like to
know how many read requests and write requests are in progress. Split the
current in_flight counter into two seperate counters for read and write.

This information is exported as a sysfs attribute, as changing the
currently available stat files would break the existing tools.

Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-09-14 08:24:52 +02:00
Jens Axboe 1f98a13f62 bio: first step in sanitizing the bio->bi_rw flag testing
Get rid of any functions that test for these bits and make callers
use bio_rw_flagged() directly. Then it is at least directly apparent
what variable and flag they check.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-09-11 14:33:31 +02:00
Geert Uytterhoeven 0d03d59d9b md: Fix "strchr" [drivers/md/dm-log-userspace.ko] undefined!
Commit b8313b6da7 ("dm log: remove incorrect
field from userspace table output") added a call to strstr() with a
single-character "needle" string parameter.

Unfortunately some versions of gcc replace such calls to strstr() by calls
to strchr() behind our back.  This causes linking errors if strchr() is
defined as an inline function in <asm/string.h> (e.g. on m68k):

| WARNING: "strchr" [drivers/md/dm-log-userspace.ko] undefined!

Avoid this by explicitly calling strchr() instead.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-10 14:55:01 -07:00
Dan Williams 9134d02bc0 Merge commit 'md/for-linus' into async-tx-next
Conflicts:
	drivers/md/raid5.c
2009-09-08 17:55:54 -07:00
Dan Williams bbb20089a3 Merge branch 'dmaengine' into async-tx-next
Conflicts:
	crypto/async_tx/async_xor.c
	drivers/dma/ioat/dma_v2.h
	drivers/dma/ioat/pci.c
	drivers/md/raid5.c
2009-09-08 17:55:21 -07:00
Dan Williams 0403e38277 dmaengine: add fence support
Some engines optimize operation by reading ahead in the descriptor chain
such that descriptor2 may start execution before descriptor1 completes.
If descriptor2 depends on the result from descriptor1 then a fence is
required (on descriptor2) to disable this optimization.  The async_tx
api could implicitly identify dependencies via the 'depend_tx'
parameter, but that would constrain cases where the dependency chain
only specifies a completion order rather than a data dependency.  So,
provide an ASYNC_TX_FENCE to explicitly identify data dependencies.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-09-08 17:42:50 -07:00
Dan Williams f9dd213437 Merge branch 'md-raid6-accel' into ioat3.2
Conflicts:
	include/linux/dmaengine.h
2009-09-08 17:42:29 -07:00
Mikulas Patocka ae0b7448e9 dm snapshot: fix on disk chunk size validation
Fix some problems seen in the chunk size processing when activating a
pre-existing snapshot.

For a new snapshot, the chunk size can either be supplied by the creator
or a default value can be used.  For an existing snapshot, the
chunk size in the snapshot header on disk should always be used.

If someone attempts to load an existing snapshot and has the 'default
chunk size' option set, the kernel uses its default value even when it
is incorrect for the snapshot being loaded.  This patch ensures the
correct on-disk value is always used.

Secondly, when the code does use the chunk size stored on the disk it is
prudent to revalidate it, so the code can exit cleanly if it got
corrupted as happened in
https://bugzilla.redhat.com/show_bug.cgi?id=461506 .

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:43 +01:00
Mikulas Patocka 2defcc3fb4 dm exception store: split set_chunk_size
Break the function set_chunk_size to two functions in preparation for
the fix in the following patch.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:41 +01:00
Mikulas Patocka 61578dcd3f dm snapshot: fix header corruption race on invalidation
If a persistent snapshot fills up, a race can corrupt the on-disk header
which causes a crash on any future attempt to activate the snapshot
(typically while booting).  This patch fixes the race.

When the snapshot overflows, __invalidate_snapshot is called, which calls
snapshot store method drop_snapshot. It goes to persistent_drop_snapshot that
calls write_header. write_header constructs the new header in the "area"
location.

Concurrently, an existing kcopyd job may finish, call copy_callback
and commit_exception method, that goes to persistent_commit_exception.
persistent_commit_exception doesn't do locking, relying on the fact that
callbacks are single-threaded, but it can race with snapshot invalidation and
overwrite the header that is just being written while the snapshot is being
invalidated.

The result of this race is a corrupted header being written that can
lead to a crash on further reactivation (if chunk_size is zero in the
corrupted header).

The fix is to use separate memory areas for each.

See the bug: https://bugzilla.redhat.com/show_bug.cgi?id=461506

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:39 +01:00
Mikulas Patocka 02d2fd31de dm snapshot: refactor zero_disk_area to use chunk_io
Refactor chunk_io to prepare for the fix in the following patch.

Pass an area pointer to chunk_io and simplify zero_disk_area to use
chunk_io.  No functional change.

Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:37 +01:00
Jonathan Brassow 7ec23d5094 dm log: userspace add luid to distinguish between concurrent log instances
Device-mapper userspace logs (like the clustered log) are
identified by a universally unique identifier (UUID).  This
identifier is used to associate requests from the kernel to
a specific log in userspace.  The UUID must be unique everywhere,
since multiple machines may use this identifier when communicating
about a particular log, as is the case for cluster logs.

Sometimes, device-mapper/LVM may re-use a UUID.  This is the
case during pvmoves, when moving from one segment of an LV
to another, or when resizing a mirror, etc.  In these cases,
a new log is created with the same UUID and loaded in the
"inactive" slot.  When a device-mapper "resume" is issued,
the "live" table is deactivated and the new "inactive" table
becomes "live".  (The "inactive" table can also be removed
via a device-mapper 'clear' command.)

The above two issues were colliding.  More than one log was being
created with the same UUID, and there was no way to distinguish
between them.  So, sometimes the wrong log would be swapped
out during the exchange.

The solution is to create a locally unique identifier,
'luid', to go along with the UUID.  This new identifier is used
to determine exactly which log is being referenced by the kernel
when the log exchange is made.  The identifier is not
universally safe, but it does not need to be, since
create/destroy/suspend/resume operations are bound to a specific
machine; and these are the operations that make up the exchange.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:34 +01:00
Jonathan Brassow d2b698644c dm raid1: do not allow log_failure variable to unset after being set
This patch fixes a bug which was triggering a case where the primary leg
could not be changed on failure even when the mirror was in-sync.

The case involves the failure of the primary device along with
the transient failure of the log device.  The problem is that
bios can be put on the 'failures' list (due to log failure)
before 'fail_mirror' is called due to the primary device failure.
Normally, this is fine, but if the log device failure is transient,
a subsequent iteration of the work thread, 'do_mirror', will
reset 'log_failure'.  The 'do_failures' function then resets
the 'in_sync' variable when processing bios on the failures list.
The 'in_sync' variable is what is used to determine if the
primary device can be switched in the event of a failure.  Since
this has been reset, the primary device is incorrectly assumed
to be not switchable.

The case has been seen in the cluster mirror context, where one
machine realizes the log device is dead before the other machines.
As the responsibilities of the server migrate from one node to
another (because the mirror is being reconfigured due to the failure),
the new server may think for a moment that the log device is fine -
thus resetting the 'log_failure' variable.

In any case, it is inappropiate for us to reset the 'log_failure'
variable.  The above bug simply illustrates that it can actually
hurt us.

Cc: stable@kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:32 +01:00
Jonathan Brassow b8313b6da7 dm log: remove incorrect field from userspace table output
The output of 'dmsetup table' includes an internal field that should not
be there.  This patch removes it.  To make the fix simpler, we first
reorder a constructor argument

The 'device size' argument is generated internally.  Currently it is
placed as the last space-separated word of the constructor string.
However, we need to use a version of the string without this word, so we
move it to the beginning instead so it is trivial to skip past it.

We keep a copy of the arguments passed to userspace for creating a log,
just in case we need to resend them.  These are the same arguments that
are desired in the STATUSTYPE_TABLE request, except for one.  When
creating the userspace log, the userspace daemon must know the size of
the mirror, so that is added to the arguments given in the constructor
table.  We were printing this extra argument out as well, which is a
mistake.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:30 +01:00
Jonathan Brassow 4142a96917 dm log: fix userspace status output
Fix 'dmsetup table' output.

There is a missing ' ' at the end of the string causing two
words to run together.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:28 +01:00
Mike Snitzer 40bea43127 dm stripe: expose correct io hints
Set sensible I/O hints for striped DM devices in the topology
infrastructure added for 2.6.31 for userspace tools to
obtain via sysfs.

Add .io_hints to 'struct target_type' to allow the I/O hints portion
(io_min and io_opt) of the 'struct queue_limits' to be set by each
target and implement this for dm-stripe.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:25 +01:00
Mike Snitzer a963a95622 dm table: add more context to terse warning messages
A couple of recent warning messages make it difficult for the reader to
determine exactly what is wrong.  This patch adds more information to
those messages.

The messages were added by these commits:
  5dea271b6d ("dm table: pass correct dev area size
to device_area_is_valid")
  ea9df47cc9 ("dm table: fix blk_stack_limits arg
to use bytes not sectors")

The patch also corrects references to logical_block_size in printk format
strings from %hu to %u.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:24 +01:00
Mikulas Patocka f6a1ed1086 dm table: fix queue_limit checking device iterator
The logic to check for valid device areas is inverted relative to proper
use with iterate_devices.

The iterate_devices method calls its callback for every underlying
device in the target.  If any callback returns non-zero, iterate_devices
exits immediately.  But the callback device_area_is_valid() returns 0 on
error and 1 on success.  The overall effect without is that an error is
issued only if every device is invalid.

This patch renames device_area_is_valid to device_area_is_invalid and
inverts the logic so that one invalid device is sufficient to raise
an error.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:22 +01:00
Mike Snitzer 8811f46c1f dm snapshot: implement iterate devices
Implement the .iterate_devices for the origin and snapshot targets.
dm-snapshot's lack of .iterate_devices resulted in the inability to
properly establish queue_limits for both targets.

With 4K sector drives: an unfortunate side-effect of not establishing
proper limits in either targets' DM device was that IO to the devices
would fail even though both had been created without error.

Commit af4874e03e ("dm target:s introduce
iterate devices fn") in 2.6.31-rc1 should have implemented .iterate_devices
for dm-snap.c's origin and snapshot targets.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:19 +01:00
Kiyoshi Ueda a77e28c7e1 dm multipath: fix oops when request based io fails when no paths
The patch posted at http://marc.info/?l=dm-devel&m=124539787228784&w=2
which was merged into cec47e3d4a ("dm:
prepare for request based option") introduced a regression in
request-based dm.

If map_request() calls dm_kill_unmapped_request() to complete a cloned
bio without dispatching it, clone->bio is still set when
dm_end_request() is called and the BUG_ON(clone->bio) is incorrect.

The patch fixes this bug by freeing bio in dm_end_request() if the clone
has bio.  I've redone my tests to cover all I/O paths and confirmed
there's no other regression.

Here is the oops I hit in request-based dm when I do I/O to a multipath
device which doesn't have any active path nor queue_if_no_path setting:

------------[ cut here ]------------
kernel BUG at /root/2.6.31-rc4.rqdm/drivers/md/dm.c:828!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/cpu3/cache/index2/shared_cpu_map
CPU 1
Modules linked in: autofs4 sunrpc cpufreq_ondemand acpi_cpufreq dm_mirror dm_region_hash dm_log dm_service_time dm_multipath scsi_dh dm_mod video output sbs sbshc battery ac sg sr_mod e1000e button cdrom serio_raw rtc_cmos rtc_core rtc_lib piix lpfc scsi_transport_fc ata_piix libata megaraid_sas sd_mod scsi_mod crc_t10dif ext3 jbd uhci_hcd ohci_hcd ehci_hcd [last unloaded: microcode]
Pid: 7, comm: ksoftirqd/1 Not tainted 2.6.31-rc4.rqdm #1 Express5800/120Lj [N8100-1417]
RIP: 0010:[<ffffffffa023629d>]  [<ffffffffa023629d>] dm_softirq_done+0xbd/0x100 [dm_mod]
RSP: 0018:ffff8800280a1f08  EFLAGS: 00010282
RAX: ffffffffa02544e0 RBX: ffff8802aa1111d0 RCX: ffff8802aa1111e0
RDX: ffff8802ab913e70 RSI: 0000000000000000 RDI: ffff8802ab913e70
RBP: ffff8800280a1f28 R08: ffffc90005457040 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 00000000fffffffb
R13: ffff8802ab913e88 R14: ffff8802ab9c1438 R15: 0000000000000100
FS:  0000000000000000(0000) GS:ffff88002809e000(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000003d54a98640 CR3: 000000029f0a1000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process ksoftirqd/1 (pid: 7, threadinfo ffff8802ae50e000, task ffff8802ae4f8040)
Stack:
 ffff8800280a1f38 0000000000000020 ffffffff814f30a0 0000000000000004
<0> ffff8800280a1f58 ffffffff8116b245 ffff8800280a1f38 ffff8800280a1f38
<0> ffff8800280a1f58 0000000000000001 ffff8800280a1fa8 ffffffff810477bc
Call Trace:
 <IRQ>
 [<ffffffff8116b245>] blk_done_softirq+0x75/0x90
 [<ffffffff810477bc>] __do_softirq+0xcc/0x210
 [<ffffffff81047170>] ? ksoftirqd+0x0/0x110
 [<ffffffff8100ce7c>] call_softirq+0x1c/0x50
 <EOI>
 [<ffffffff8100e785>] do_softirq+0x65/0xa0
 [<ffffffff81047170>] ? ksoftirqd+0x0/0x110
 [<ffffffff810471e0>] ksoftirqd+0x70/0x110
 [<ffffffff81059559>] kthread+0x99/0xb0
 [<ffffffff8100cd7a>] child_rip+0xa/0x20
 [<ffffffff8100c73c>] ? restore_args+0x0/0x30
 [<ffffffff810594c0>] ? kthread+0x0/0xb0
 [<ffffffff8100cd70>] ? child_rip+0x0/0x20
Code: 44 89 e6 48 89 df e8 23 fb f2 e0 be 01 00 00 00 4c 89 f7 e8 f6 fd ff ff 5b 41 5c 41 5d 41 5e c9 c3 4c 89 ef e8 85 fe ff ff eb ed <0f> 0b eb fe 41 8b 85 dc 00 00 00 48 83 bb 10 01 00 00 00 89 83
RIP  [<ffffffffa023629d>] dm_softirq_done+0xbd/0x100 [dm_mod]
 RSP <ffff8800280a1f08>
---[ end trace 16af0a1d8542da55 ]---

Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2009-09-04 20:40:16 +01:00
Dan Williams 07a3b417dc md/raid456: distribute raid processing over multiple cores
Now that the resources to handle stripe_head operations are allocated
percpu it is possible for raid5d to distribute stripe handling over
multiple cores.  This conversion also adds a call to cond_resched() in
the non-multicore case to prevent one core from getting monopolized for
raid operations.

Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-08-29 19:13:13 -07:00
Yuri Tikhonov b774ef491b md/raid6: remove synchronous infrastructure
These routines have been replaced by there asynchronous counterparts.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-08-29 19:13:13 -07:00
Yuri Tikhonov 6c0069c0ae md/raid6: asynchronous handle_stripe6
1/ Use STRIPE_OP_BIOFILL to offload completion of read requests to
   raid_run_ops
2/ Implement a handler for sh->reconstruct_state similar to the raid5 case
   (adds handling of Q parity)
3/ Prevent handle_parity_checks6 from running concurrently with 'compute'
   operations
4/ Hook up raid_run_ops

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-08-29 19:13:13 -07:00
Dan Williams d82dfee0ad md/raid6: asynchronous handle_parity_check6
[ Based on an original patch by Yuri Tikhonov ]

Implement the state machine for handling the RAID-6 parities check and
repair functionality.  Note that the raid6 case does not need to check
for new failures, like raid5, as it will always writeback the correct
disks.  The raid5 case can be updated to check zero_sum_result to avoid
getting confused by new failures rather than retrying the entire check
operation.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-08-29 19:13:13 -07:00
Yuri Tikhonov a9b39a741a md/raid6: asynchronous handle_stripe_dirtying6
In the synchronous implementation of stripe dirtying we processed a
degraded stripe with one call to handle_stripe_dirtying6().  I.e.
compute the missing blocks from the other drives, then copy in the new
data and reconstruct the parities.

In the asynchronous case we do not perform stripe operations directly.
Instead, operations are scheduled with flags to be later serviced by
raid_run_ops.  So, for the degraded case the final reconstruction step
can only be carried out after all blocks have been brought up to date by
being read, or computed.  Like the raid5 case schedule_reconstruction()
sets STRIPE_OP_RECONSTRUCT to request a parity generation pass and
through operation chaining can handle compute and reconstruct in a
single raid_run_ops pass.

[dan.j.williams@intel.com: fixup handle_stripe_dirtying6 gating]
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-08-29 19:13:12 -07:00
Yuri Tikhonov 5599becca4 md/raid6: asynchronous handle_stripe_fill6
Modify handle_stripe_fill6 to work asynchronously by introducing
fetch_block6 as the raid6 analog of fetch_block5 (schedule compute
operations for missing/out-of-sync disks).

[dan.j.williams@intel.com: compute D+Q in one pass]
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-08-29 19:13:12 -07:00
Yuri Tikhonov c0f7bddbe6 md/raid5,6: common schedule_reconstruction for raid5/6
Extend schedule_reconstruction5 for reuse by the raid6 path.  Add
support for generating Q and BUG() if a request is made to perform
'prexor'.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-08-29 19:13:12 -07:00