Update the PCIe phy settings based on new settings available
in AM572x Technical Reference Manual[1] Revision I, revised
April 2017 in Table 26-62 "Preferred PCIe_PHY_RX SCP Register
Settings".
[1] http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[nsekhar@ti.com: commit message updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PCI core access configuration space registers in resume_noirq callbacks.
In the case of dra7xx, PIPE3 PHY connected to PCIe controller has to be
enabled before accessing configuration space registers. Since
PIPE3 PHY is enabled by only configuring control module registers, no
aborts has been observed so far (though during noirq stage, interface
clock of PIPE3 PHY is not enabled).
With new TRM updates, PIPE3 PHY has to be initialized (PIPE3 PHY
registers has to be accessed) as well which requires the interface
clock of PIPE3 PHY to be enabled. The interface clock of PIPE3 PHY is
derived from OCP2SCP and hence PCIe PHY is modeled as a child of
OCP2SCP. Since pm_runtime is not enabled during noirq stage,
pm_runtime_get_sync done in phy_init doesn't enable
OCP2SCP clocks resulting in abort when PIPE3 PHY registers are
accessed.
Create a function dependency between PCIe and PHY here to make
sure PCIe is suspended before PCIe PHY/OCP2SCP and resumed after
PCIe PHY/OCP2SCP.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Parse the DT properties brcm,rxaeq-mode and brcm,rxaeq-value to
correctly configure the RX equalizer of the PHY. This may be required to
resolve specific signal integrity issues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Split the functional code in brcm_stb_sata_init() to a separate function
that actually does configure spread spectrum: brcm_stb_sata_ssc_init()
and make that function return void, since that function cannot fail.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Define two new properties: brcm,rx-aeq-mode which allows configuring the
SATA PHY RX equalizers and when "manual" is used, brcm,rx-aeq can be
used to set the exact value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds binding for r8a77995 (R-Car D3). Since r8a77995 doesn't
have dedicated pins (ID, VBUS), this will match against the generic
fallback on R-Car D3.
For now, this driver doesn't support usb role swap for r8a77995.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds SoC-specific parameter to avoid reading/writing
specific registers wrongly if this driver runs on a SoC which doesn't
have dedicated pins (e.g. R-Car D3). This patch also changes the
value "has_otg" to "has_otg_pins" for slightly easier reading of
the code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch modifies the role_store() to use "enum phy_mode" instead
of the local "bool" for host/device mode selection.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The previous code assumed a channel has otg capability if a channel
has interrupt property. But, it is not good because:
- Battery charging feature also needs interrupt property.
- Some R-Car Gen3 SoCs (e.g. R-Car D3) don't have OTG capability.
So, this patch checks whether usb 2.0 host node has dr_mode property or
not. If it has 'dr_mode = "otg";', this driver enables otg capability.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add USB PHY support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5)
USB PHY is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner V3s SoC also features the dual route of the first USB PHY.
Enable it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Calculate the calibration code as per the docs. The docs talk about
reading and averaging the pullup and pulldown calibration codes. They
also talk about adding in some adjustment codes. Let's do what the
docs say.
In practice this doesn't seem to matter a whole lot. On a device I
tested the pullup and pulldown codes were nearly the same (0x23 and
0x24) and the adjustment codes were 0.
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
NOTE: nothing is known to be fixed by this change, but it does enforce
some delays that are documented to be necessary. Possibly this could
fix some corner cases.
The function tcphy_dp_aux_calibration(), like most of the functions in
the type C PHY, is mostly undocumented and filled with mysterious,
hardcoded numbers.
Let's attempt to try to document some of these numbers and clean the
function up a little bit. Here's the actual cleanup that happened
here:
1. All magic numbers were replaced with bit definitions.
2. For registers that we modify multiple times I now keep track of the
value of the register rather than randomly doing a
read/modify/write or just hardcoding a new number based on knowing
what the old number was.
3. Delay 10 ms (vs 1 ms) after writing the calibration code. No idea
if this is important but it matches the example in the docs.
4. Whenever setting a "delayed" version of a signal always put an
explicit delay in the code. No known problems were seen without
this delay but it seems wise to have it. Whenever a delay of "at
least 100 ns" was specified I used a delay of 1 us.
5. Added comments to some of the bits of code.
6. Removed duplicate setting of TX_ANA_CTRL_REG_5 (to 0)
7. Moved setting of TX_ANA_CTRL_REG_3 to the same place it was in the
sample code. Note that TX_ANA_CTRL_REG_3 ought to be initted to 0
(and elsewhere we assume that we just got a reset), but it seems
fine to be explicit.
8. Treats the calibration code as a 7-bit two's complement number.
This isn't strictly required, but seems slightly cleaner. The docs
say "treat this as a two's complement number, but it should never
be negative". If we ever read the "adjustment" codes as documented
then perhaps the two's complement bit will matter more.
There are still a few weird / mysterious things around aux init and
this doesn't attempt to fix all of them. Mostly it's aimed at doing
changes that should be _very_ safe and add a lot of clarity. Things
specifically not done:
A) Resolve the fact that some registers are read/modify/write and
others are explicitly initted to a value. We always call
tcphy_dp_aux_calibration() right after resetting the PHY so it's
probably not critical, but it's a little weird that the code is
inconsistent.
B) Fully resolve the documented init sequence with the current one.
We still have a few mystery steps and we also leave out turning on
TXDA_DRV_LDO_BG_FB_EN and TXDA_DRV_LDO_BG_REF_EN, which is in the
sample code.
C) Clean things up to read all the bits of the calibration code. This
will hopefully come in a followup change.
This also doesn't attempt to document any of the other parts of the
PHY--just the aux init which is all I got docs for.
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If we're trying to get a handle to an optional phy, then the phy framework
being disabled shouldn't return an hard error.
Instead, return NULL just like phy_optional_get does when there's no phy
provided in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is used to force PHY with USB OTG function to enter a specific
mode, and override OTG IDPIN(or IDDIG) signal.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 'modes' member of the mvebu_comphy_priv structure is not used.
Remove it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The variable "ret" is immediately reassigned by a following statement.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The array extcon_info is read only, local to the source and does not
need to be in global scope, so make it static const.
Cleans up sparse warning:
symbol 'extcon_info' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull input fix from Dmitry Torokhov:
"A fix for a broken commit in the previous pull breaking automatic
module loading of input handlers, such ad evdev"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: do not use property bits when generating module alias
The commit 8724ecb072 ("Input: allow matching device IDs on property
bits") started using property bits when generating module aliases for input
handlers, but did not adjust the generation of MODALIAS attribute on input
device uevents, breaking automatic module loading. Given that no handler
currently uses property bits in their module tables, let's revert this part
of the commit for now.
Reported-by: Damien Wyart <damien.wyart@gmail.com>
Tested-by: Damien Wyart <damien.wyart@gmail.com>
Fixes: 8724ecb072 ("Input: allow matching device IDs on property bits")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull x86 fixes from Thomas Gleixner:
"A couple of fixes addressing the following issues:
- The last polishing for the TLB code, removing the last BUG_ON() and
the debug file along with tidying up the lazy TLB code.
- Prevent triple fault on 1st Gen. 486 caused by stupidly calling the
early IDT setup after the first function which causes a fault which
should be caught by the exception table.
- Limit the mmap of /dev/mem to valid addresses
- Prevent late microcode loading on Broadwell X
- Remove a redundant assignment in the cache info code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/mm: Remove debug/x86/tlb_defer_switch_to_init_mm
x86/mm: Tidy up "x86/mm: Flush more aggressively in lazy TLB mode"
x86/mm/64: Remove the last VM_BUG_ON() from the TLB code
x86/microcode/intel: Disable late loading on model 79
x86/idt: Initialize early IDT before cr4_init_shadow()
x86/cpu/intel_cacheinfo: Remove redundant assignment to 'this_leaf'
Pull timer fix from Thomas Gleixner:
"A single fix to make the cs5535 clock event driver robust agaist
spurious interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents/drivers/cs5535: Improve resilience to spurious interrupts
Pull smp/hotplug fix from Thomas Gleixner:
"The recent rework of the callback invocation missed to cleanup the
leftovers of the operation, so under certain circumstances a
subsequent CPU hotplug operation accesses stale data and crashes.
Clean it up."
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Reset node state after operation
Pull perf fixes from Thomas Gleixner:
"A series of fixes for perf tooling:
- Make xyarray return the X/Y size correctly which fixes a crash in
the exit code.
- Fix the libc path in test so it works not only on Debian/Ubuntu
correctly
- Check for eBPF file existance and output a useful error message
instead of failing to compile a non existant file
- Make sure perf_hpp_fmt is not longer references before freeing it
- Use list_del_init() in the histogram code to prevent a crash when
the already deleted element is deleted again
- Remove the leftovers of the removed '-l' option
- Add reviewer entries to the MAINTAINERS file"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf test shell trace+probe_libc_inet_pton.sh: Be compatible with Debian/Ubuntu
perf xyarray: Fix wrong processing when closing evsel fd
perf buildid-list: Fix crash when processing PERF_RECORD_NAMESPACE
perf record: Fix documentation for a inexistent option '-l'
perf tools: Add long time reviewers to MAINTAINERS
perf tools: Check wether the eBPF file exists in event parsing
perf hists: Add extra integrity checks to fmt_free()
perf hists: Fix crash in perf_hpp__reset_output_field()
Pull irq fixes from Thomas Gleixner:
"A set of small fixes mostly in the irq drivers area:
- Make the tango irq chip work correctly, which requires a new
function in the generiq irq chip implementation
- A set of updates to the GIC-V3 ITS driver removing a bogus BUG_ON()
and parsing the VCPU table size correctly"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: generic chip: remove irq_gc_mask_disable_reg_and_ack()
irqchip/tango: Use irq_gc_mask_disable_and_ack_set
genirq: generic chip: Add irq_gc_mask_disable_and_ack_set()
irqchip/gic-v3-its: Add missing changes to support 52bit physical address
irqchip/gic-v3-its: Fix the incorrect parsing of VCPU table size
irqchip/gic-v3-its: Fix the incorrect BUG_ON in its_init_vpe_domain()
DT: arm,gic-v3: Update the ITS size in the examples
Pull objtool fix from Thomas Gleixner:
"Plug a memory leak in the instruction decoder"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix memory leak in decode_instructions()
Pull networking fixes from David Miller:
"A little more than usual this time around. Been travelling, so that is
part of it.
Anyways, here are the highlights:
1) Deal with memcontrol races wrt. listener dismantle, from Eric
Dumazet.
2) Handle page allocation failures properly in nfp driver, from Jaku
Kicinski.
3) Fix memory leaks in macsec, from Sabrina Dubroca.
4) Fix crashes in pppol2tp_session_ioctl(), from Guillaume Nault.
5) Several fixes in bnxt_en driver, including preventing potential
NVRAM parameter corruption from Michael Chan.
6) Fix for KRACK attacks in wireless, from Johannes Berg.
7) rtnetlink event generation fixes from Xin Long.
8) Deadlock in mlxsw driver, from Ido Schimmel.
9) Disallow arithmetic operations on context pointers in bpf, from
Jakub Kicinski.
10) Missing sock_owned_by_user() check in sctp_icmp_redirect(), from
Xin Long.
11) Only TCP is supported for sockmap, make that explicit with a
check, from John Fastabend.
12) Fix IP options state races in DCCP and TCP, from Eric Dumazet.
13) Fix panic in packet_getsockopt(), also from Eric Dumazet.
14) Add missing locked in hv_sock layer, from Dexuan Cui.
15) Various aquantia bug fixes, including several statistics handling
cures. From Igor Russkikh et al.
16) Fix arithmetic overflow in devmap code, from John Fastabend.
17) Fix busted socket memory accounting when we get a fault in the tcp
zero copy paths. From Willem de Bruijn.
18) Don't leave opt->tot_len uninitialized in ipv6, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
stmmac: Don't access tx_q->dirty_tx before netif_tx_lock
ipv6: flowlabel: do not leave opt->tot_len with garbage
of_mdio: Fix broken PHY IRQ in case of probe deferral
textsearch: fix typos in library helpers
rxrpc: Don't release call mutex on error pointer
net: stmmac: Prevent infinite loop in get_rx_timestamp_status()
net: stmmac: Fix stmmac_get_rx_hwtstamp()
net: stmmac: Add missing call to dev_kfree_skb()
mlxsw: spectrum_router: Configure TIGCR on init
mlxsw: reg: Add Tunneling IPinIP General Configuration Register
net: ethtool: remove error check for legacy setting transceiver type
soreuseport: fix initialization race
net: bridge: fix returning of vlan range op errors
sock: correct sk_wmem_queued accounting on efault in tcp zerocopy
bpf: add test cases to bpf selftests to cover all access tests
bpf: fix pattern matches for direct packet access
bpf: fix off by one for range markings with L{T, E} patterns
bpf: devmap fix arithmetic overflow in bitmap_size calculation
net: aquantia: Bad udp rate on default interrupt coalescing
net: aquantia: Enable coalescing management via ethtool interface
...
This is the possible reason for different hard to reproduce
problems on my ARMv7-SMP test system.
The symptoms are in recent kernels imprecise external aborts,
and in older kernels various kinds of network stalls and
unexpected page allocation failures.
My testing indicates that the trouble started between v4.5 and v4.6
and prevails up to v4.14.
Using the dirty_tx before acquiring the spin lock is clearly
wrong and was first introduced with v4.6.
Fixes: e3ad57c967 ("stmmac: review RX/TX ring management")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When syzkaller team brought us a C repro for the crash [1] that
had been reported many times in the past, I finally could find
the root cause.
If FlowLabel info is merged by fl6_merge_options(), we leave
part of the opt_space storage provided by udp/raw/l2tp with random value
in opt_space.tot_len, unless a control message was provided at sendmsg()
time.
Then ip6_setup_cork() would use this random value to perform a kzalloc()
call. Undefined behavior and crashes.
Fix is to properly set tot_len in fl6_merge_options()
At the same time, we can also avoid consuming memory and cpu cycles
to clear it, if every option is copied via a kmemdup(). This is the
change in ip6_setup_cork().
[1]
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 6613 Comm: syz-executor0 Not tainted 4.14.0-rc4+ #127
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801cb64a100 task.stack: ffff8801cc350000
RIP: 0010:ip6_setup_cork+0x274/0x15c0 net/ipv6/ip6_output.c:1168
RSP: 0018:ffff8801cc357550 EFLAGS: 00010203
RAX: dffffc0000000000 RBX: ffff8801cc357748 RCX: 0000000000000010
RDX: 0000000000000002 RSI: ffffffff842bd1d9 RDI: 0000000000000014
RBP: ffff8801cc357620 R08: ffff8801cb17f380 R09: ffff8801cc357b10
R10: ffff8801cb64a100 R11: 0000000000000000 R12: ffff8801cc357ab0
R13: ffff8801cc357b10 R14: 0000000000000000 R15: ffff8801c3bbf0c0
FS: 00007f9c5c459700(0000) GS:ffff8801db200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020324000 CR3: 00000001d1cf2000 CR4: 00000000001406f0
DR0: 0000000020001010 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000600
Call Trace:
ip6_make_skb+0x282/0x530 net/ipv6/ip6_output.c:1729
udpv6_sendmsg+0x2769/0x3380 net/ipv6/udp.c:1340
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:762
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
SYSC_sendto+0x358/0x5a0 net/socket.c:1750
SyS_sendto+0x40/0x50 net/socket.c:1718
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x4520a9
RSP: 002b:00007f9c5c458c08 EFLAGS: 00000216 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000000000718000 RCX: 00000000004520a9
RDX: 0000000000000001 RSI: 0000000020fd1000 RDI: 0000000000000016
RBP: 0000000000000086 R08: 0000000020e0afe4 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000216 R12: 00000000004bb1ee
R13: 00000000ffffffff R14: 0000000000000016 R15: 0000000000000029
Code: e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 ea 0f 00 00 48 8d 79 04 48 b8 00 00 00 00 00 fc ff df 45 8b 74 24 04 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85
RIP: ip6_setup_cork+0x274/0x15c0 net/ipv6/ip6_output.c:1168 RSP: ffff8801cc357550
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an Ethernet PHY is initialized before the interrupt controller it is
connected to, a message like the following is printed:
irq: no irq domain found for /interrupt-controller@e61c0000 !
However, the actual error is ignored, leading to a non-functional (POLL)
PHY interrupt later:
Micrel KSZ8041RNLI ee700000.ethernet-ffffffff:01: attached PHY driver [Micrel KSZ8041RNLI] (mii_bus:phy_addr=ee700000.ethernet-ffffffff:01, irq=POLL)
Depending on whether the PHY driver will fall back to polling, Ethernet
may or may not work.
To fix this:
1. Switch of_mdiobus_register_phy() from irq_of_parse_and_map() to
of_irq_get().
Unlike the former, the latter returns -EPROBE_DEFER if the
interrupt controller is not yet available, so this condition can be
detected.
Other errors are handled the same as before, i.e. use the passed
mdio->irq[addr] as interrupt.
2. Propagate and handle errors from of_mdiobus_register_phy() and
of_mdiobus_register_device().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spellos (typos) in textsearch library helpers.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't release call mutex at the end of rxrpc_kernel_begin_call() if the
call pointer actually holds an error value.
Fixes: 540b1c48c3 ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Fix HW timestamping
Three fixes for HW timestamping feature, all of them for RX side.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent infinite loop by correctly setting the loop condition to
break when i == 10.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GMAC4 the valid timestamp is from CTX next desc but
we are passing the previous desc to get_rx_timestamp_status()
callback.
Fix this and while at it rework a little bit the function logic.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX HW timestamp is enabled and a frame is discarded we are
not freeing the skb but instead only setting to NULL the entry.
Add a call to dev_kfree_skb_any() so that skb entry is correctly
freed.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fixes from Dmitry Torokhov:
- joydev now implements a blacklist to avoid creating joystick nodes
for accelerometers found in composite devices such as PlaStation
controllers
- assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-psu - check if CDC union descriptor is sane
Input: joydev - blacklist ds3/ds4/udraw motion sensors
Input: allow matching device IDs on property bits
Input: factor out and export input_device_id matching code
Input: goodix - poll the 'buffer status' bit before reading data
Input: axp20x-pek - fix module not auto-loading for axp221 pek
Input: tca8418 - enable interrupt after it has been requested
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Input: synaptics - disable kernel tracking on SMBus devices
Pull vfs fixes from Al Viro:
"MS_I_VERSION fixes - Mimi's fix + missing bits picked from Matthew
(his patch contained a duplicate of the fs/namespace.c fix as well,
but by that point the original fix had already been applied)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Convert fs/*/* to SB_I_VERSION
vfs: fix mounting a filesystem with i_version
Jiri Pirko says:
====================
mlxsw: spectrum: Configure TTL of "inherit" for offloaded tunnels
Petr says:
Currently mlxsw only offloads tunnels that are configured with TTL of "inherit"
(which is the default). However, Spectrum defaults to 255 and the driver
neglects to change the configuration. Thus the tunnel packets from offloaded
tunnels always have TTL of 255, even though tunnels with explicit TTL of 255 are
never actually offloaded.
To fix this, introduce support for TIGCR, the register that keeps the related
bits of global tunnel configuration, and use it on first offload to properly
configure inheritance of TTL of tunnel packets from overlay packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum tunnels do not default to ttl of "inherit" like the Linux ones
do. Configure TIGCR on router init so that the TTL of tunnel packets is
copied from the overlay packets.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9cab88726929605 ("net: ethtool: Add back transceiver type")
restores the transceiver type to struct ethtool_link_settings and
convert_link_ksettings_to_legacy_settings() but forgets to remove the
error check for the same in convert_legacy_settings_to_link_ksettings().
This prevents older versions of ethtool to change link settings.
# ethtool --version
ethtool version 3.16
# ethtool -s eth0 autoneg on speed 100 duplex full
Cannot set new settings: Invalid argument
not setting speed
not setting duplex
not setting autoneg
While newer versions of ethtool works.
# ethtool --version
ethtool version 4.10
# ethtool -s eth0 autoneg on speed 100 duplex full
[ 57.703268] sh-eth ee700000.ethernet eth0: Link is Down
[ 59.618227] sh-eth ee700000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
Fixes: 19cab88726 ("net: ethtool: Add back transceiver type")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Renjith R V <renjith.rv@quest-global.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller stumbled upon a way to trigger
WARNING: CPU: 1 PID: 13881 at net/core/sock_reuseport.c:41
reuseport_alloc+0x306/0x3b0 net/core/sock_reuseport.c:39
There are two initialization paths for the sock_reuseport structure in a
socket: Through the udp/tcp bind paths of SO_REUSEPORT sockets or through
SO_ATTACH_REUSEPORT_[CE]BPF before bind. The existing implementation
assumedthat the socket lock protected both of these paths when it actually
only protects the SO_ATTACH_REUSEPORT path. Syzkaller triggered this
double allocation by running these paths concurrently.
This patch moves the check for double allocation into the reuseport_alloc
function which is protected by a global spin lock.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: c125e80b88 ("soreuseport: fast reuseport TCP socket selection")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan tunnels were introduced, vlan range errors got silently
dropped and instead 0 was returned always. Restore the previous
behaviour and return errors to user-space.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller hits WARN_ON(sk->sk_wmem_queued) in sk_stream_kill_queues
after triggering an EFAULT in __zerocopy_sg_from_iter.
On this error, skb_zerocopy_stream_iter resets the skb to its state
before the operation with __pskb_trim. It cannot kfree_skb like
datagram callers, as the skb may have data from a previous send call.
__pskb_trim calls skb_condense for unowned skbs, which adjusts their
truesize. These tcp skbuffs are owned and their truesize must add up
to sk_wmem_queued. But they match because their skb->sk is NULL until
tcp_transmit_skb.
Temporarily set skb->sk when calling __pskb_trim to signal that the
skbuffs are owned and avoid the skb_condense path.
Fixes: 52267790ef ("sock: add MSG_ZEROCOPY")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
Two BPF fixes for range marking
The set contains two fixes for direct packet access range
markings and test cases for all direct packet access patterns
that the verifier matches on.
They are targeted for net tree, note that once net gets merged
into net-next, there will be a minor merge conflict due to
signature change of the function find_good_pkt_pointers() as
well as data_meta patterns present in net-next tree. You can
just add bool false to the data_meta patterns and I will
follow-up with properly converting the patterns for data_meta
in a similar way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets add test cases to cover really all possible direct packet
access tests for good/bad access cases so we keep tracking them.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander had a test program with direct packet access, where
the access test was in the form of data + X > data_end. In an
unrelated change to the program LLVM decided to swap the branches
and emitted code for the test in form of data + X <= data_end.
We hadn't seen these being generated previously, thus verifier
would reject the program. Therefore, fix up the verifier to
detect all test cases, so we don't run into such issues in the
future.
Fixes: b4e432f100 ("bpf: enable BPF_J{LT, LE, SLT, SLE} opcodes in verifier")
Reported-by: Alexander Alemayhu <alexander@alemayhu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During review I noticed that the current logic for direct packet
access marking in check_cond_jmp_op() has an off by one for the
upper right range border when marking in find_good_pkt_pointers()
with BPF_JLT and BPF_JLE. It's not really harmful given access
up to pkt_end is always safe, but we should nevertheless correct
the range marking before it becomes ABI. If pkt_data' denotes a
pkt_data derived pointer (pkt_data + X), then for pkt_data' < pkt_end
in the true branch as well as for pkt_end <= pkt_data' in the false
branch we mark the range with X although it should really be X - 1
in these cases. For example, X could be pkt_end - pkt_data, then
when testing for pkt_data' < pkt_end the verifier simulation cannot
deduce that a byte load of pkt_data' - 1 would succeed in this
branch.
Fixes: b4e432f100 ("bpf: enable BPF_J{LT, LE, SLT, SLE} opcodes in verifier")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kishon Vijay Abraham I
Florian Fainelli
Yoshihiro Shimoda
Biju Das
Icenowy Zheng
Douglas Anderson
Maxime Ripard
Chunfeng Yun
Antoine Tenart
Markus Elfring
Colin Ian King
Chanwoo Choi
Linus Torvalds
Dmitry Torokhov
Bernd Edlinger
Eric Dumazet
Geert Uytterhoeven
Randy Dunlap
David Howells
David S. Miller
Jose Abreu
Petr Machata
Niklas Söderlund
Craig Gallek
Nikolay Aleksandrov
Willem de Bruijn
Daniel Borkmann