Allocating and sending the skb in dcb_doit() allows for much
shorter and cleaner command handling functions.
The huge switch statement is replaced with an array based definition
of the handling function and reply message type.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to allocate and send the reply message in each
handling function separately. Instead, the reply skb can be allocated
and sent in dcb_doit() directly.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop connection monitor poll during disassociation.
This clears the polling flags and if a scan was
deferred it will be run.
Without this fix, if a scan was deferred due to
connection monitoring while disassociation happens,
this scan blocks further scan requests until interface
down/up which causes problems connecting to another AP.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we might call the driver callback before
the interface was uploaded.
Solves the following warning:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x0
Modules linked in: wlcore_sdio wl12xx wl18xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[<c001b964>] (unwind_backtrace+0x0/0x12c) from [<c0495550>] (dump_stack+0x20/0x24)
[<c0495550>] (dump_stack+0x20/0x24) from [<c003ee28>] (warn_slowpath_common+0x5c/0x74)
[<c003ee28>] (warn_slowpath_common+0x5c/0x74) from [<c003eefc>] (warn_slowpath_fmt+0x40/0x48)
[<c003eefc>] (warn_slowpath_fmt+0x40/0x48) from [<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211])
[<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]) from [<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211])
[<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211]) from [<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8)
[<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8) from [<c03e9164>] (netlink_rcv_skb+0x5c/0xc0)
[<c03e9164>] (netlink_rcv_skb+0x5c/0xc0) from [<c03e9ce0>] (genl_rcv+0x28/0x34)
[<c03e9ce0>] (genl_rcv+0x28/0x34) from [<c03e8e74>] (netlink_unicast+0x158/0x234)
[<c03e8e74>] (netlink_unicast+0x158/0x234) from [<c03e93e0>] (netlink_sendmsg+0x218/0x298)
[<c03e93e0>] (netlink_sendmsg+0x218/0x298) from [<c03b4e5c>] (sock_sendmsg+0xa4/0xc0)
[<c03b4e5c>] (sock_sendmsg+0xa4/0xc0) from [<c03b5af4>] (__sys_sendmsg+0x1d8/0x254)
[<c03b5af4>] (__sys_sendmsg+0x1d8/0x254) from [<c03b5ca8>] (sys_sendmsg+0x4c/0x70)
[<c03b5ca8>] (sys_sendmsg+0x4c/0x70) from [<c0013980>] (ret_fast_syscall+0x0/0x3c)
Note that calling the driver can also result
in undefined behaviour since it doesn't have
to deal with calls while down.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[removed timestamps, added note - Johannes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
'Get' commands should generally not require CAP_NET_ADMIN, with
the exception of those that expose internal state.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dev_loopback_xmit() in order to deduplicate functions
ip_dev_loopback_xmit() (in net/ipv4/ip_output.c) and
ip6_dev_loopback_xmit() (in net/ipv6/ip6_output.c).
I was about to reinvent the wheel when I noticed that
ip_dev_loopback_xmit() and ip6_dev_loopback_xmit() do exactly what I
need and are not IP-only functions, but they were not available to reuse
elsewhere.
ip6_dev_loopback_xmit() does not have line "skb_dst_force(skb);", but I
understand that this is harmless, and should be in dev_loopback_xmit().
Signed-off-by: Michel Machado <michel@digirati.com.br>
CC: "David S. Miller" <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing of 127/8 is tradtionally forbidden, we consider
packets from that address block martian when routing and do
not process corresponding ARP requests.
This is a sane default but renders a huge address space
practically unuseable.
The RFC states that no address within the 127/8 block should
ever appear on any network anywhere but it does not forbid
the use of such addresses outside of the loopback device in
particular. For example to address a pool of virtual guests
behind a load balancer.
This patch adds a new interface option 'route_localnet'
enabling routing of the 127/8 address block and processing
of ARP requests on a specific interface.
Note that for the feature to work, the default local route
covering 127/8 dev lo needs to be removed.
Example:
$ sysctl -w net.ipv4.conf.eth0.route_localnet=1
$ ip route del 127.0.0.0/8 dev lo table local
$ ip addr add 127.1.0.1/16 dev eth0
$ ip route flush cache
V2: Fix invalid check to auto flush cache (thanks davem)
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few kernel-doc descriptions that were missed
during mesh development.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If remote device sends bogus RFC option with invalid length,
undefined options values are used. Fix this by using defaults when
remote misbehaves.
This also fixes the following warning reported by gcc 4.7.0:
net/bluetooth/l2cap_core.c: In function 'l2cap_config_rsp':
net/bluetooth/l2cap_core.c:3302:13: warning: 'rfc.max_pdu_size' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.max_pdu_size' was declared here
net/bluetooth/l2cap_core.c:3298:25: warning: 'rfc.monitor_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.monitor_timeout' was declared here
net/bluetooth/l2cap_core.c:3297:25: warning: 'rfc.retrans_timeout' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.retrans_timeout' was declared here
net/bluetooth/l2cap_core.c:3295:2: warning: 'rfc.mode' may be used uninitialized in this function [-Wmaybe-uninitialized]
net/bluetooth/l2cap_core.c:3266:24: note: 'rfc.mode' was declared here
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This small patch removes access to the last element of the spkt_device
array through a constant. Instead, it is accessed by sizeof() to respect
possible changes in if_packet.h.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the compilation of the TCP and UDP trackers with sysctl
compilation disabled:
net/netfilter/nf_conntrack_proto_udp.c: In function ‘udp_init_net_data’:
net/netfilter/nf_conntrack_proto_udp.c:279:13: error: ‘struct nf_proto_net’ has no member named
‘user’
net/netfilter/nf_conntrack_proto_tcp.c:1606:9: error: ‘struct nf_proto_net’ has no member named
‘user’
net/netfilter/nf_conntrack_proto_tcp.c:1643:9: error: ‘struct nf_proto_net’ has no member named
‘user’
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle NULL in rt{,6}_set_peer but then our caller will try to pass
that NULL pointer into inet_putpeer() which isn't ready for it.
Fix this by moving the NULL check one level up, and then remove the
now unnecessary NULL check from inetpeer_ptr_set_peer().
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implementation can deal with having many inetpeer roots, which is
a necessary prerequisite for per-FIB table rooted peer tables.
Each family (AF_INET, AF_INET6) has a sequence number which we bump
when we get a family invalidation request.
Each peer lookup cheaply checks whether the flush sequence of the
root we are using is out of date, and if so flushes it and updates
the sequence number.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is zero point to this function.
It's only real substance is to perform an extremely outdated BSD4.2
ICMP check, which we can safely remove. If you really have a MTU
limited link being routed by a BSD4.2 derived system, here's a nickel
go buy yourself a real router.
The other actions of ip_rt_frag_needed(), checking and conditionally
updating the peer, are done by the per-protocol handlers of the ICMP
event.
TCP, UDP, et al. have a handler which will receive this event and
transmit it back into the associated route via dst_ops->update_pmtu().
This simplification is important, because it eliminates the one place
where we do not have a proper route context in which to make an
inetpeer lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
We encode the pointer(s) into an unsigned long with one state bit.
The state bit is used so we can store the inetpeer tree root to use
when resolving the peer later.
Later the peer roots will be per-FIB table, and this change works to
facilitate that.
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Michael Tokarev , struct unix_iter_state is no longer
needed.
Suggested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need one interface for this operation, since we always know
which inetpeer root we want to flush.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it's guarenteed that we will access the inetpeer if we're trying
to do timewait recycling and TCP options were enabled on the
connection, just cache the peer in the timewait socket.
In the future, inetpeer lookups will be context dependent (per routing
realm), and this helps facilitate that as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't validate interface combinations on a stopped
interface. Otherwise we might end up being able to
create a new interface with a certain type, but
won't be able to change an existing interface
into that type.
This also skips some other functions when
interface is stopped and changing interface type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a few kernel-doc descriptions that were missed
during development.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The get_peer method TCP uses is full of special cases that make no
sense accommodating, and it also gets in the way of doing more
reasonable things here.
First of all, if the socket doesn't have a usable cached route, there
is no sense in trying to optimize timewait recycling.
Likewise for the case where we have IP options, such as SRR enabled,
that make the IP header destination address (and thus the destination
address of the route key) differ from that of the connection's
destination address.
Just return a NULL peer in these cases, and thus we're also able to
get rid of the clumsy inetpeer release logic.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of places that open-code rt{,6}_get_peer() only because
they want to set 'create' to one. So add an rt{,6}_get_peer_create()
for their sake.
There were also a few spots open-coding plain rt{,6}_get_peer() and
those are transformed here as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in net/core:
Warning(net/core/skbuff.c:3368): No description found for parameter 'delta_truesize'
Warning(net/core/filter.c:628): No description found for parameter 'pfp'
Warning(net/core/filter.c:628): Excess function parameter 'sk' description in 'sk_unattached_filter_create'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With LE/SMP the completion of a security level elavation from medium to
high is indicated by a HCI Encryption Key Refresh Complete event. The
necessary behavior upon receiving this event is a mix of what's done for
auth_complete and encryption_change, which is also where most of the
event handling code has been copied from.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Commit 081b1b1bb2 (l2tp: fix l2tp_ip_sendmsg() route handling) added
a race, in case IP route cache is disabled.
In this case, we should not do the dst_release(&rt->dst), since it'll
free the dst immediately, instead of waiting a RCU grace period.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Cc: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/unix has quadratic behavior, and can hold unix_table_lock for
a while if high number of unix sockets are alive. (90 ms for 200k
sockets...)
We already have a hash table, so its quite easy to use it.
Problem is unbound sockets are still hashed in a single hash slot
(unix_socket_table[UNIX_HASH_TABLE])
This patch also spreads unbound sockets to 256 hash slots, to speedup
both /proc/net/unix and unix_diag.
Time to read /proc/net/unix with 200k unix sockets :
(time dd if=/proc/net/unix of=/dev/null bs=4k)
before : 520 secs
after : 2 secs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add struct net as a parameter of inet_getpeer_v[4,6],
use net to replace &init_net.
and modify some places to provide net for inet_getpeer_v[4,6]
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
now inetpeer doesn't support namespace,the information will
be leaking across namespace.
this patch move the global vars v4_peers and v6_peers to
netns_ipv4 and netns_ipv6 as a field peers.
add struct pernet_operations inetpeer_ops to initial pernet
inetpeer data.
and change family_to_base and inet_getpeer to support namespace.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 24398e39c8
Author: Johannes Berg <johannes.berg@intel.com>
Date: Wed Mar 28 10:58:36 2012 +0200
mac80211: set HT channel before association
removed IEEE80211_CONF_CHANGE_CHANNEL argument from ieee80211_hw_config,
which is required by iwl4965 driver, otherwise that driver does not
configure channel properly and is not able to associate.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
llcp_sock_getname() might get called before the LLCP socket was created.
This condition isn't checked, and llcp_sock_getname will simply deref a
NULL ptr in that case.
This exists starting with d646960 ("NFC: Initial LLCP support").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have an unauthenticated key it is not sufficient to acheive high
security. Therefore, when deciding whether to encrypt the link or
request pairing, it is essential to in addition to checking the
existence of a key to also check whether it is authenticated or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The l2cap_conn_del function tries to cancel_sync the security timer, but
when it's called from the timeout function itself a deadlock occurs.
Subsequently the "hcon->l2cap_data = NULL" that's supposed to protect
multiple calls to l2cap_conn_del never gets cleared and when the
connection finally drops we double free's etc which will crash the
kernel.
This patch fixes the issue by using the HCI_CONN_LE_SMP_PEND for
protecting against this. The same flag is also used for the same purpose
in other places in the SMP code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
For BR/EDR pairing is assumed to be finished when connection is
done. For LE if connection is successful it did not necessarily
mean that pairing is also done but if the connection is unsuccessful
it should be assumed that pairing procedure is also finished.
This patch registers a new function with connect_cfm_cb callback for
LE link which sends the pairing complete signal to user space if
connection is unsuccessful.
Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The tk_request function takes the local IO capability as the second last
parameter and the remote IO capability as the last parameter. They were
previously swapped: when we receive a pairing response
req->io_capability contains the local one and rsp->io_capability the
remote one.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
RFC 4293 defines ipIfStatsOutOctets (similar definition for
ipSystemStatsOutOctets):
The total number of octets in IP datagrams delivered to the lower
layers for transmission. Octets from datagrams counted in
ipIfStatsOutTransmits MUST be counted here.
And ipIfStatsOutTransmits:
The total number of IP datagrams that this entity supplied to the
lower layers for transmission. This includes datagrams generated
locally and those forwarded by this entity.
Therefore, IPSTATS_MIB_OUTOCTETS must be incremented when incrementing
IPSTATS_MIB_OUTFORWDATAGRAMS.
IP_UPD_PO_STATS is not used since ipIfStatsOutRequests must not
include forwarded datagrams:
The total number of IP datagrams that local IP user-protocols
(including ICMP) supplied to IP in requests for transmission. Note
that this counter does not include any datagrams counted in
ipIfStatsOutForwDatagrams.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the kernel's ethtool interface by adding support
for 2 new EEE commands - get_eee and set_eee.
Thanks goes to Giuseppe Cavallaro for his original patch adding this support.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__alloc_skb() now extends tailroom to allow the use of padding added
by the heap allocator.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidentally triggered this printk, which amused me for a few moments.
Given we're post 2.2, we could just -EACCES, but does anyone even care about Appletalk now ?
I figure it's better to leave sleeping dogs lie, and just update the message.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5339ab8b1d (ipv6: fib: Convert fib6_age() to
dst_neigh_lookup().) seems to have mistakenly inverted the
exception for cached NTF_ROUTER routes.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denys found out "ip neigh" output was truncated to
about 54 neighbours.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must prevent module unloading if some devices are still attached to
l2tp_eth driver.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The mask option allows you put all address belonging that mask into
the same recent slot. This can be useful in case that recent is used
to detect attacks from the same network segment.
Tested for backward compatibility.
Signed-off-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
because reply packets need to go to the same nfqueue, src/dst ip
address were xor'd prior to jhash().
However, this causes bad distribution for some workloads, e.g.
flows a.b.1.{1,n} -> a.b.2.{1,n} all share the same hash value.
Avoid this by hashing both. To get same hash for replies,
first argument is the smaller address.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for cttimeout.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since the sysctl data for l[3|4]proto now resides in pernet nf_proto_net.
We can now remove this unused fields from struct nf_contrack_l[3,4]proto.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch modifies the GRE protocol tracker, which partially
supported namespace before this patch, to use the new namespace
infrastructure for nf_conntrack.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch modifies the DCCP protocol tracker to use the new
namespace infrastructure for nf_conntrack.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for UDPlite protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for SCTP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for IPv6 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for IPv4 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for ICMPv6 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for ICMP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for UDP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for TCP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for the generic layer 4 protocol
tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch prepares the namespace support for layer 3 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_l3proto_[un]register_sysctl.
* nf_conntrack_l3proto_[un]register.
We add a new nf_ct_l3proto_net is used to get the pernet data of l3proto.
This adds rhe new struct nf_ip_net that is used to store the sysctl header
and l3proto_ipv4,l4proto_tcp(6),l4proto_udp(6),l4proto_icmp(v6) because the
protos such tcp and tcp6 use the same data,so making nf_ip_net as a field
of netns_ct is the easiest way to manager it.
This patch also adds init_net to struct nf_conntrack_l3proto to initial
the layer 3 protocol pernet data.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch prepares the namespace support for layer 4 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_[un]register_sysctl
* nf_conntrack_l4proto_[un]register
to include the namespace parameter. We still use init_net in this patch
to prepare the ground for follow-up patches for each layer 4 protocol
tracker.
We add a new net_id field to struct nf_conntrack_l4proto that is used
to store the pernet_operations id for each layer 4 protocol tracker.
Note that AF_INET6's protocols do not need to do sysctl compat. Thus,
we only register compat sysctl when l4proto.l3proto != AF_INET6.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Implement a new "fail-open" mode where packets are not dropped
upon queue-full condition. This mode can be enabled/disabled per
queue using netlink NFQA_CFG_FLAGS & NFQA_CFG_MASK attributes.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Vivek Kashyap <vivk@us.ibm.com>
Signed-off-by: Sridhar Samudrala <samudrala@us.ibm.com>
It was scheduled to be removed.
Cc: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nat_rtp_rtcp hook takes two separate parameters port and rtp_port.
port is expected to be the real h245 address (found inside the packet).
rtp_port is the even number closest to port (RTP ports are even and
RTCP ports are odd).
However currently, both port and rtp_port are having same value (both are
rounded to nearest even numbers).
This works well in case of openlogicalchannel with media (RTP/even) port.
But in case of openlogicalchannel for media control (RTCP/odd) port,
h245 address in the packet is wrongly modified to have an even port.
I am attaching a pcap demonstrating the problem, for any further analysis.
This behavior was introduced around v2.6.19 while rewriting the helper.
Signed-off-by: Jagdish Motwani <jagdish.motwani@elitecore.com>
Signed-off-by: Sanket Shah <sanket.shah@elitecore.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch addresses two issues:
a) Fix usage of u32 and __be32 that causes endianess warnings via sparse.
b) Ensure consistent hashing in a cluster that is composed of big and
little endian systems. Thus, we obtain the same hash mark in an
heterogeneous cluster.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
John Linville says:
====================
Amitkumar Karwar gives us a cfg80211 fix that changes some state
tracking in order to avoid a WARNING.
Arik Nemtsov provide a mac80211 fix for an RCU-related race.
Avinash Patil shares a pair of mwifiex fixes, one which invalidates
some stale configuration data before a channel change and another to
restrict hidden SSID support to zero-length SSIDs only.
Chun-Yeow Yeoh brings a mac80211 fix for a mesh problem triggered
when combining multiple mesh networks into one.
Felix Fietkau provides a mac80211 lockdep fix.
Joe Perches fixes a couple of thinkos related to bitwise operations.
Johannes Berg comes through with a flurry of fixes. The iwlwifi ones
address a problem Linus recently reported, and some of the fallout
discovered while fixing it. The mac80211 fix properly cleans-up
remain-on-channel work on an interface that is stopped. The others
are clean-ups for regressions caused by stricter checking of possible
virtual interfaces supported by wireless drivers.
Meenakshi Venkataraman provides a mac80211 fix for an off-by-one error.
Seth Forshee provides a fix to make the wireless adapters used in
some Mac boxes work after being in S3 power saving state.
Stanislaw Gruszka offers a copule of fixes, a fix for a mac80211
scanning regression and an rt2x00 fix to avoid some lockdep spew.
Last but not least, Vinicius Costa Gomes provides a bluetooth fix
for a typo that "was preventing important features of Bluetooth
from working".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When performing a HW restart for an AP mode interface, add stations back
only after the AP is beaconing. This mimics the normal flow of STA
addition on AP.
Some devices (wlcore) do not support adding stations before beaconing,
so this has the added benefit of making recovery work for them.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The remain-on-channel time validation shouldn't
depend on the value of HZ, as it does now with
the check against jiffies, since then you might
use a value that works on one system but not on
another. Fix it by checking against a minimum
that's fixed.
Also add validation of the wait duration for a
management frame TX since this also translates
into remain-on-channel internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drv_resume can get called without a prior call to drv_suspend.
Consider the following steps:
1. Suspend is started but driver's drv_suspend returns error.
2. Suspend is aborted. local->wowlan flag is left set.
3. Interface is removed.
4. Suspend again. This time open_count is 0 so drv_suspend is
not called and local->wowlan not cleared.
5. On resume ieee80211_reconfig will call drv_resume since
local->wowlan is set.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make mac80211 print a message when it disables
HT due to the connection using WEP/TKIP or due
to the AP not supporting WMM/QoS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For each EDCA TX queue change default settings (in STA mode) to conform
old 802.11b/g channel access rules. This is needed for drivers that do
not have QoS enable/disable "switch" (like rt2x00) to make them work
properly with legacy APs.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__rfkill_switch_all() switches the state of devices of a given type; however,
it does not switch devices of all type (RFKILL_TYPE_ALL). As a result, it
ignores the keycode "KEY_RFKILL" from another module, i.e. eeepc-wmi.
This fix is to make __rfkill_switch_all() to be able to switch not only
devices of a given type but also all devices.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 5faa5df1fa (inetpeer: Invalidate the inetpeer tree along with
the routing cache) added a race :
Before freeing an inetpeer, we must respect a RCU grace period, and make
sure no user will attempt to increase refcnt.
inetpeer_invalidate_tree() waits for a RCU grace period before inserting
inetpeer tree into gc_list and waking the worker. At that time, no
concurrent lookup can find a inetpeer in this tree.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If it worked (Felix says it doesn't right now), the
typical use-case for WDS interfaces would be to be
slaved to AP mode interfaces. Therefore, it isn't
necessary to set the channel on WDS interfaces. As
they don't support powersave or anything like that,
they also couldn't use a different channel anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change cfg80211_can_beacon_sec_chan() to return true
if there is no secondary channel to simplify all the
current users of it. They all check the channel type
before calling the function because it returns false
if there's no secondary channel.
Also actually document the return value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the set_channel function up so it can be used
by other code in this file in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for ieee80211_set_channel to check
whether a change in configuration happened since
ieee80211_hw_config() auto-detects it.
Additionally, it's wrong to pretend the HT config
for the BSS changed, it didn't, the BSS can't be
up & running (AP beaconing etc.) when the channel
type is changed anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing around the entire HT information
IE, extract only the HT parameters field and disable
HT if the HT information IE isn't present and well-
formed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all wireless tools have transitioned to
or at least added compatibility with nl80211 so
there's no real need for CONFIG_CFG80211_WEXT
any more. Mark it for removal, and also change
the default to not be enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only user of this was hal prior to its 0.5.12
release which happened over two years ago, so I'm
sure this can be removed without issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_operstate() was used by drivers in order to
know whether the sta link is up, but it's no longer needed
(nor used) as mac80211 notifies the drivers about
authorization changes (via the sta_state callback)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the use of #ifdef CONFIG_MAC80211_IBSS_DEBUG/#endif
by adding a logging macro to encapsulate the test.
Convert the appropriate uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the use of #ifdef CONFIG_MAC80211_HT_DEBUG/#endif
by adding a logging macro to encapsulate the test.
Convert the appropriate uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send beacon loss events to userspace, so it will be
able to initiate roaming before disconnection
Signed-off-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow channel change on a mesh interface if the interface is up and no
mesh is started.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx_mgmt_auth() doesn't handle denied authentication
properly - it authenticates the station and waits for association
(for 5 seconds) instead of failing the authentication.
Fix it by destroying auth_data and bailing out instead.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@vger.kernel.org #3.4
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 3a25a8c ("mac80211: add improved HW queue control")
added support for offchannel queue mapping. However, this
mapping is only valid when the driver supports
IEEE80211_HW_QUEUE_CONTROL.
Check whether the driver supports IEEE80211_HW_QUEUE_CONTROL
before setting the hw_queue to the mapped offchannel queue.
(This patch doesn't have any actual effect, because
hw_queue is overridden in ieee80211_tx() anyway,
so this is merely some cleanup)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Low level drivers can now set certain netdev feature bits in
netdev_features member of the ieee80211_hw struct. These will be
propagated to every netdev created from this HW.
The white-listed features currently include only ones related to HW
checksumming.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Cc: stable@kernel.org
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macro gives a better idea of the what the error really is.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Most probably a typo, the check should have been for BT_SK_DEFER_SETUP
instead of BT_DEFER_SETUP (which right now only represents a socket
option).
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch enables filtering duplicated advertising reports during
LE scan.
Some LE devices advertise using very small intervals generating lots
of equal advertising report events to the host. Each event generates
a mgmt_device_found event which is copied to userspace.
Enabling this feature, duplicated advertising reports are filtered
at controller's link layer. This way, the controller doesn't wake up
the host to report duplicated advertising reports and, consequently,
less data is copied to userspace.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
A2MP doesn't use part of the L2CAP chan ops API so we just create general
empty function instead of the A2MP specific one.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch renames L2CAP_LE_DEFAULT_MTU macro to L2CAP_LE_MIN_MTU
since it represents the minimum MTU value, not the default MTU
value for LE.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If user tries to set an invalid MTU value, l2cap_sock_setsockopt_old
should return -EINVAL.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch changes the default MTU value for L2CAP ATT fixed channel
to L2CAP_DEFAULT_MTU (672 octets).
Differently from others L2CAP channels, in L2CAP ATT fixed channel
there is no MTU negotiation. The MTU value for that channel is up to
the L2CAP implementation. The only restriction in L2CAP spec is the
MTU value must not be less than 23 octets.
At ATT protocol level (on top of L2CAP), we have the ATT_MTU which
defines the maximum size of any ATT message sent between client and
server. GATT profile defines ATT_MTU default value to 23 octets. If
a GATT based profile wants to use ATT_MTU greater than 23 octets
(e.g. HID over GATT profile), it should negotiate a new value by
executing the GATT Exchange MTU sub-procedure.
Thus, in order to support any value of ATT_MTU negotiated at ATT
protocol level, our L2CAP implementation should have L2CAP ATT
fixed channel MTU equal or greater than ATT_MAX_MTU (512 octets).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch changes way LE Connection Complete event with error status are
handled. BDADDR returned in such event packet do not need to be valid and
should not be used to search for existing hci_conn. Instead, any hci_conn
with BT_CONNECT state should be matched since there can be only one
pending LE outgoing connection at any time.
If not handled properly, appriopriate hci_conn will not be removed and
subsequent connection to given peer will try to reuse it without making
actual connection attempt.
2012-05-07 11:21:39.133378 < HCI Command: LE Create Connection (0x08|0x000d) plen 25
bdaddr 00:22:D0:10:13:EE type 1
2012-05-07 11:21:39.138774 > HCI Event: Command Status (0x0f) plen 4
LE Create Connection (0x08|0x000d) status 0x00 ncmd 1
2012-05-07 11:21:44.752854 < HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0
2012-05-07 11:21:44.759475 > HCI Event: Command Complete (0x0e) plen 4
LE Create Connection Cancel (0x08|0x000e) ncmd 1
2012-05-07 11:21:44.764479 > HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete
status 0x02 handle 0, role master
bdaddr 00:00:00:00:00:00 (Public)
[14898.739425] [6603] hci_connect: hci0 dst 00:22:D0:10:13:EE
[14898.739429] [6603] hci_conn_add: hci0 dst 00:22:D0:10:13:EE
[14898.739434] [6603] hci_conn_init_sysfs: conn ffff880079f03000
[14898.739440] [6603] hci_send_cmd: hci0 opcode 0x200d plen 25
[14898.739443] [6603] hci_send_cmd: skb len 28
[14898.739487] [6603] hci_chan_create: hci0 conn ffff880079f03000
...
[14938.860231] [55] hci_send_cmd: hci0 opcode 0x200e plen 0
...
[14938.876427] [55] hci_le_conn_complete_evt: hci0 status 2
[14938.876433] [55] hci_conn_add: hci0 dst 00:00:00:00:00:00
[14938.876439] [55] hci_conn_init_sysfs: conn ffff88007aeff800
[14938.876454] [55] hci_send_to_control: len 14
[14938.876470] [55] l2cap_connect_cfm: hcon ffff88007aeff800 bdaddr 00:00:00:00:00:00 status 2
[14938.876474] [55] hci_conn_del: hci0 conn ffff88007aeff800 handle 0
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
MGMT_STATUS_BUSY should be returned when LE pairing cannot be started due
to another outgoing connection attempt is ongoing.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Only one outgoing LE connection attempt should be possible.
hci_connect() will now return -EBUSY in case there's another pending
outgoing connection.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Trivial fix, let the code cleaner.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Simplify the handling of different ERTM header size. We were the same
check in some places of the code, and more is expected to come, so just
replace them with a function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
l2cap_att_channel always returns 0 which is not used.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
l2cap_conless_channel always return 0 which is not used.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
l2cap_data_channel always return 0 which is not used anywhere,
make it void function.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Make A2MP channel special channel which do not reference hci_conn.
This prevents from keeping ACL connection open when all L2CAP
channels got closed.
hci_conn_hold and hci_conn_put are not reference counts on the
hci_conn structure in the typical way. They are reference counts for
the ACL. When you do the last hci_conn_put, the ACL is disconnected
after a timeout.
Reported-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Functions will be always defined and in case not implemented as
dummy __no_func.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
A2MP fixed channel do not have sk
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Process A2MP responses, print cmd code and ident for now.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Placeholder for A2MP Create Physlink Request.
Handles requests with invalid controler id as shown below:
...
> ACL data: handle 11 flags 0x02 dlen 50
A2MP: Create Physical Link req: local id 1 remote id 85
Assoc data:
<skipped>
< ACL data: handle 11 flags 0x00 dlen 15
A2MP: Create Physical Link rsp: local id 85 remote id 1 status 1
Invalid Controller ID
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Process A2MP Get Info Request.
Example of trace log for invalid controller id is shown below:
...
> ACL data: handle 11 flags 0x02 dlen 13
A2MP: Get Info req: id 238
< ACL data: handle 11 flags 0x00 dlen 30
A2MP: Get Info rsp: id 238 status (1) Invalid Controller ID
...
Note that If the Status field is set to Invalid Controller ID all subsequent
fields in the AMP Get Info Response shall be ignored by the receiver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Helper function to build and send A2MP messages.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Define AMP Manager and some basic functions.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Move this check to before the channel time creation simplifies the code
and avoid memory allocation if the channel already exist.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These vars are kept in sync so we can use chan->state here.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This move socket specific code to l2cap_sock.c.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This remove a bit more of socket code from l2cap core, this calls set the
SOCK_ZAPPED and do some clean up depending on the socket state.
Reported-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use chan instead of void * makes more sense here.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This replace code in l2cap_le_conn_ready() by a similar code in
l2cap_chan_ready().
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is already performed inside l2cap_chan_ready(), so we don't need it
here again.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both FCS and Extended header might be or might not be present in a ERTM
channel.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
__constant_cpu_to_le16() is the right go here.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Define assigned Protocol and Service Multiplexor (PSM) identifiers
and use them instead of magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Make the check more user friendly.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Define Continuation flag which the only flag used from Flags field
in L2CAP Configuration Request and Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After l2cap, sco and bluetooth modules merge some symbols doesn't need to
be exported anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most of the include were unnecessary or already included by some other
header.
Replace module.h by export.h where possible.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is some leftover from the last patches that fixed style. It is mostly
line over 80 characters fixes reported by checkpatch.pl.
checkpatch.pl is clean for these files now.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let the compiler chooses what is best.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only obvious cases were left as inline, mostly oneline functions.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous callers of l2cap_build_conf_rsp in l2cap_config_req use
flags instead of continuation flag hardcoded value. It does not change
logic and preserve future possible flags.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove magic number with defined link key size.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to
reset device on close instead of init, not to not reset at all.
Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These functions were returning always 0, we just make then void.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The same check is done just before call l2cap_streaming_send()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Silence warnings below:
net/bluetooth/l2cap_core.c:1662:24: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:1662:27: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:1683:24: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:1683:27: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:2260:46: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:2574:33: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:2581:33: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:4556:24: warning: Using plain integer
as NULL pointer
net/bluetooth/l2cap_core.c:4556:27: warning: Using plain integer
as NULL pointer
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
chan->tx_q is only initialized if we use ERTM or Streaming mode.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables the new receive and transmit state machines.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The transmit window values must be configured for streaming mode, even
though streaming mode does not have a window. This enables use of
extended headers when the transmit window socket option is set to 64
or larger.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Let the compiler decide if inlining is appropriate.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since l2cap_send_ack can trigger extra actions like sending iframes,
don't call it. Just send an RR or RNR frame if an ack needs sending.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Different states have different actions for retransmit and monitor
timeouts, so remove the logic for those actions from the timer handlers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The ERTM specification requires the retransmit timer to be cancelled
when the monitor timer is set. The retransmit timer cannot be set
again while the monitor timer is pending.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
struct l2cap_ctrl is now used, and the sframe is now sent directly
rather than depending on a separate call.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
REJ frames are sent by the remote device to request that all frames
after a given sequence number be retransmitted. These are also an
implicit indication that the remote device is not in a busy state and
can receive new iframes.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When a remote device sends an SREJ, retransmit the frame with the
corresponding sequence number (subject to special cases with poll and
final flags). An SREJ is also an implicit indication the the remote
device is not in a busy state.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
As retransmitted packets arrive, attempt to reassemble SDUs. If all
requested retransmissions have been received, acknowledge them and
transition back to the RECV state.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The ERTM specification lays out three scenarios for sending SREJ
frames to request retransmission of specific frames. l2cap_send_srej
requests all frames up to a given txseq that are not already queued
for reassembly. l2cap_send_srej_tail only requests the most recent
missing frame. l2cap_send_srej_list resends SREJ frames for data that
was requested for resend but never received.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This adds l2cap_ertm_resend to retransmit frames based on the sequence
numbers in chan->retrans_list. If the retransmit limit is reached for
any individual frame is reached, the connection is dropped. skbs that
are cloned already are copied to avoid modifying shared data (this is
uncommon). To retransmit all frames, l2cap_retransmit_all now builds
a list of all unacked sequence numbers and then calls
l2cap_ertm_resend.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This adds a top-level state machine with handlers for two receive
states defined in the ERTM spec, RECV and SREJ_SENT. The reqseq value
of the incoming frame is also validated at the top level and a
disconnection is forced if it is invalid. The actions for the RECV
and SREJ_SENT states are implemented according to the state tables in
the ERTM specification.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This action now exactly matches what is defined in the ERTM
specification, including clearing the remote busy flag and setting the
retransmit timer rather than retransmitting frames directly. The spec
does not retransmit frames as part of this action, since
retransmission is only triggered by REJ, SREJ, or an RR with the final
bit set. struct l2cap_ctrl is also used to set up header values.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This lets the transmit state machine handle local busy state changes,
since different actions are taken in the different transmit states.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The function now encapsulates more of the logic to either immediately
send an ack if the transmit window is over 75% full, or wait for the
ack timer to expire if the transmit window is not full enough. It is
also able to push out waiting iframes that can carry an
acknowledgement.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This deletes the receive code that had handlers for each frame type at
the top level, and then had logic to determine the receive state
within each handler.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Streaming mode reception is fairly simple, with in-sequence frames
being reassembled as they arrive. Out-of-sequence frames are dropped,
and also clear any partially-assembled SDUs that may exist.
The packet classifier determines if the txseq value of the incoming
packet is expected, invalid (resulting in a disconnection), invalid
(ignorable), duplicate, or having to do with an SREJ request that was
previously sent. The rules for each classification are defined in the
ERTM specification, and consolidating these rules in one place helps
clarify the receive state machine.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Thomas Graf
John W. Linville
David Spinadel
Eliad Peller
David S. Miller
Ben Hutchings
Michel Machado
Ashok Nagarajan
Szymon Janc
danborkmann@iogearbox.net
Pablo Neira Ayuso
Eric Dumazet
Gustavo Padovan
Michal Kazior
Johannes Berg
Randy Dunlap
Johan Hedberg
Eric Dumazet
Gao feng
Stanislaw Gruszka
Sasha Levin
Vishal Agarwal
Vincent Bernat
Yuval Mintz
Dave Jones
Alban Crequy
Denys Fedoryshchenko
Florian Westphal
Gao feng
Krishna Kumar
Cong Wang
Hans Schillstrom
Arik Nemtsov
Pontus Fuchs
Chun-Yeow Yeoh
Alex Hung
Joe Perches
Holger Schurig
Thomas Pedersen
Andrei Emeltchenko
Vinicius Costa Gomes
Andre Guedes
Andrzej Kaczmarek
Mat Martineau