Commit Graph

217 Commits

Author SHA1 Message Date
Philip P. Moltmann 48e3d668b7 VMware balloon: Enable notification via VMCI
Get notified immediately when a balloon target is set, instead of waiting for
up to one second.

The up-to 1 second gap could be long enough to cause swapping inside of the
VM that receives the VM.

Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Tested-by: Siva Sankar Reddy B <sankars@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04 12:59:11 +01:00
Tim Bird 1f26d1c105 ARM: qcom: Add coincell charger driver
This driver is used to configure the coincell charger found in
Qualcomm PMICs.

The driver allows configuring the current-limiting resistor for
the charger, as well as the voltage to apply to the coincell
(or capacitor) when charging.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-29 13:37:18 -07:00
Ira Snyder 0d09f1a54d misc: remove drivers for CARMA hardware
The CARMA project has ended, and the hardware has all been moved into
storage. It is unlikely to ever be used again.

Remove the drivers so that there is no more maintenance burden from
ongoing upstream kernel changes.

Signed-off-by: Ira W. Snyder <ira.snyder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:11:55 -07:00
Nicolas Ferre 9373090d9f ARM: at91/Kconfig: remove unused config options
When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-11-19 11:39:23 +01:00
Ian Munsie 10542ca015 cxl: Add base builtin support
This adds the base cxl support that cannot be built as a module. Specifically
it adds the cxl callbacks that are called from the core powerpc mm code which
must always exist irrespective of if the cxl module is loaded or not. This is
similar to how cell works with CONFIG_SPU_BASE.

This adds a cxl_slbia() call (similar to spu_flush_all_slbs()) which checks if
the cxl module is loaded and in use, returning immediately if it is not. If it
is in use it calls into the cxl SLB invalidation code.

Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2014-10-08 20:15:56 +11:00
Alexandre Belloni f2a70e1fc1 misc: atmel_pwm: remove obsolete driver
The misc/atmel_pwm is not used by any mainlined boards and has been replaced by
the pwm-driver using the generic PWM framework.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-07-09 15:14:35 +02:00
Nicolas Ferre 8dcd598c74 misc: atmel_pwm: fix Kconfig symbols
AT91 symbols AT91SAM9263, AT91SAM9RL, and AT91SAM9G45 do not exist and this
patch changes them to their correct ARCH_* version.
These symbols are chosen instead of the SOC_* ones because this driver is not
converted to DT.
Anyway, the ATMEL_PWM symbol and the associated driver will be removed soon,
during the move to the PWM sub-system.

Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-06-25 13:49:53 +02:00
Linus Torvalds 4046136afb Char / misc driver patches for 3.16-rc1
Here is the big char / misc driver updates for 3.16-rc1.
 
 Lots of different driver updates for a variety of different drivers and
 minor driver subsystems.
 
 All have been in linux-next with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iEYEABECAAYFAlONWI8ACgkQMUfUDdst+ykvQACdGxTChdEU7edElDAXeelVmu8v
 D1UAoLDvqwUsN7t5v+WG2wkOvhf5MEA7
 =tVMP
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next

Pull char/misc driver patches from Greg KH:
 "Here is the big char / misc driver update for 3.16-rc1.

  Lots of different driver updates for a variety of different drivers
  and minor driver subsystems.

  All have been in linux-next with no reported issues"

* tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits)
  hv: use correct order when freeing monitor_pages
  spmi: of: fixup generic SPMI devicetree binding example
  applicom: dereferencing NULL on error path
  misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl()
  miscdevice.h: Simple syntax fix to make pointers consistent.
  MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
  mcb: Add support for shared PCI IRQs
  drivers: Remove duplicate conditionally included subdirs
  misc: atmel_pwm: only build for supported platforms
  mei: me: move probe quirk to cfg structure
  mei: add per device configuration
  mei: me: read H_CSR after asserting reset
  mei: me: drop harmful wait optimization
  mei: me: fix hw ready reset flow
  mei: fix memory leak of mei_clients array
  uio: fix vma io range check in mmap
  drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe()
  w1: do not unlock unheld list_mutex in __w1_remove_master_device()
  w1: optional bundling of netlink kernel replies
  connector: allow multiple messages to be sent in one packet
  ...
2014-06-03 08:06:56 -07:00
Arnd Bergmann 1690e35f9b misc: atmel_pwm: only build for supported platforms
There is architecture code in mach-at91 that depends on the
CONFIG_ATMEL_PWM symbol in order to call the soc-specific
at91_add_device_pwm function. While all of this is about code
that will be removed in the future, using DT probing and
the PWM framework, we currently get a build failure:

arch/arm/mach-at91/built-in.o: In function `at91_pwm_leds':
arch/arm/mach-at91/leds.c:88: undefined reference to `at91_add_device_pwm'

This patch ensures we only try to build this driver on
platforms on which it will build and work.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 14:24:34 -07:00
Jean Delvare fd1a73c60e misc: pch_phub: Fix Kconfig dependencies
The pch_phub driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-27 12:21:43 -07:00
Pawel Moll 974cc7b934 mfd: vexpress: Define the device as MFD cells
This patch - finally, after over 6 months! :-( - addresses
Samuel's request to split the vexpress-sysreg driver into
smaller portions and define the device in a form of MFD
cells:

* LEDs code has been completely removed and replaced with
  "gpio-leds" nodes in the tree (referencing dedicated
  GPIO subnodes in sysreg - bindings documentation updated);
  this also better fits the reality as some variants of the
  motherboard don't have all the LEDs populated

* syscfg bridge code has been extracted into a separate
  driver (placed in drivers/misc for no better place)

* all the ID & MISC registers are defined as sysconf
  making them available for other drivers should they need
  to use them (and also to the user via /sys/kernel/debug/regmap
  which can be helpful in platform debugging)

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
2014-05-15 17:02:19 +01:00
Jean Delvare fc1a5dbe49 misc: Add hardware dependencies to Atmel drivers
According to the driver descriptions, the atmel_pwm and atmel-ssc
drivers are only useful on Atmel AT32 and AT91 systems. So add
hardware dependencies to these drivers to hide them on other systems.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-03 19:25:17 -04:00
Geert Uytterhoeven a82cb8b91a misc: Grammar s/addition/additional/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-16 12:28:47 -07:00
Linus Torvalds c12e69c6aa Staging driver pull request for 3.15-rc1
Here's the huge drivers/staging/ update for 3.15-rc1.
 
 Loads of cleanup fixes, a few drivers removed, and some new ones added.
 
 All have been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iEYEABECAAYFAlM7BqAACgkQMUfUDdst+ykHUwCguJDlvM7/FGb3QQslAuKN5Np4
 n2YAoJ3C355mo8Wxr/bJah3Jms4f+a7Q
 =4XGY
 -----END PGP SIGNATURE-----

Merge tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging driver updates from Greg KH:
 "Here's the huge drivers/staging/ update for 3.15-rc1.

  Loads of cleanup fixes, a few drivers removed, and some new ones
  added.

  All have been in linux-next for a while"

* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
  staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
  staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
  staging: comedi: poc: remove obsolete driver
  staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
  staging: octeon-usb: prevent memory corruption
  staging: usbip: fix line over 80 characters
  staging: usbip: fix quoted string split across lines
  Staging: unisys: Remove RETINT macro
  Staging: unisys: Remove FAIL macro
  Staging: unisys: Remove RETVOID macro
  Staging: unisys: Remove RETPTR macro
  Staging: unisys: Remove RETBOOL macro
  Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
  Staging: unisys: Cleanup macros to get rid of goto statements
  Staging: unisys: include: Remove unused macros from timskmod.h
  staging: dgap: fix the rest of the checkpatch warnings in dgap.c
  Staging: bcm: Remove unnecessary parentheses
  staging: wlags49_h2: Delete unnecessary braces
  staging: wlags49_h2: Do not use assignment in if condition
  staging: wlags49_h2: Enclose macro in a do-while loop
  ...
2014-04-01 16:45:00 -07:00
Jean Delvare 0f78a11e24 cs5535-mfgpt: Simplify dependencies
The bus and architecture dependencies are already on MFD_CS5535, so
there is no need to repeat them here.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-08 22:15:52 -08:00
Greg Kroah-Hartman 6e2055a9e5 staging: echo: move to drivers/misc/
The code is clean, there are users of it, so it doesn't belong in
staging anymore, move it to drivers/misc/.

Cc: Steve Underwood <steveu@coppice.org>
Cc: David Rowe <david@rowetel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-28 14:08:42 -08:00
Frank Haverkamp 76f5adbcb3 GenWQE Enable driver
Enable possiblity to configure and build this driver.

Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Co-authors: Joerg-Stephan Vogt <jsvogt@de.ibm.com>,
            Michael Jung <MIJUNG@de.ibm.com>,
            Michael Ruettger <michael@ibmra.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-18 16:51:15 -08:00
Linus Torvalds 0bde7294e2 pwm: Changes for v3.13-rc1
Mostly bug fixes and clean up. There is a new driver, which is actually
 moving a custom PWM driver from drivers/misc.
 
 The majority of the patches are enhancements to the device tree support
 in the pwm-backlight driver. Backlights can now additionally be powered
 using a regulator and enabled using a GPIO in addition to just the PWM
 input.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABAgAGBQJSh1s7AAoJEN0jrNd/PrOhdS4P/1A/Tx05pP0ACsizhkB4Ro02
 XgjIusWw/jp+3LWXrlaReVNb5H6GlahDT5+2/ApAw06o7INGvpSzyI1fuFQ2DU6K
 L7MgWDSifeL7jiwfUq5f3Qv4Vccjgii0z4BBQI5ZpPluIzKpo2uhz7gIjBR3wPu9
 i34bc902SL/DrlvbMUsRHlYT9Ok3TpsPynk0pmw8xrUZDqRAX7DZH0EmvMkVsDo2
 T1vt9gQVTFVgIwlRUBcbrjbu1GnYaV20s+piQhYm1RMSUqY+ArldWKzEzlN3tLYc
 XdnkaLikdHDRBA4DeNPJGbPU8LQax8wCTaZa1PgT0PqjNX/dCkg3hsc1Em0dH9Zh
 PKvyX8R6iPdOcakkRm4qdVIacblqE1HYM7T+lyVhu6XP7MWkUmNr05HQBFjhOMcm
 whv1gS/EeB4y/FcSzn7S23UAmOvxiWfGnOMlnazrOgS00FrbC4accgSB/iXi2lDC
 szO9MHwfbwDTp8WBLEw8iTPODpq7pnFcBCw80pzblMFqC8v1MAFyriwT7BUmKcR/
 h/V75Q95VPAKq+uKsfb5Ruwa9CGKs8ACagLR0BuErT/J83Q7Q4Ezf56FUCvrGDtz
 5AWpGUakotwHtJPx6TAOgI+237MFh/GpIOrlEtz+2b5SP6ftHxr8rj+wg1sxmI2y
 JohOUIFjHtcA4UifhlTU
 =CB+z
 -----END PGP SIGNATURE-----

Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm changes from Thierry Reding:
 "Mostly bug fixes and clean up.  There is a new driver, which is
  actually moving a custom PWM driver from drivers/misc.

  The majority of the patches are enhancements to the device tree
  support in the pwm-backlight driver.  Backlights can now additionally
  be powered using a regulator and enabled using a GPIO in addition to
  just the PWM input"

* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
  Documentation/pwm: Update supported SoC name for pwm-samsung
  pwm: samsung: Fix kernel warning while unexporting a channel
  MAINTAINERS: Move PWM subsystem tree to kernel.org
  Documentation/pwm: Fix trivial typos
  pwm-backlight: Remove unused variable
  pwm_backlight: avoid short blank screen while doing hibernation
  pwm-backlight: Fix brightness adjustment
  pwm: add ep93xx PWM support
  pwm-backlight: Allow for non-increasing brightness levels
  pwm-backlight: Add power supply support
  pwm-backlight: Use new enable_gpio field
  unicore32: Initialize PWM backlight enable_gpio field
  ARM: shmobile: Initialize PWM backlight enable_gpio field
  ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
  ARM: pxa: Initialize PWM backlight enable_gpio field
  ARM: OMAP: Initialize PWM backlight enable_gpio field
  pwm-backlight: Add optional enable GPIO
  pwm-backlight: Track enable state
  pwm-backlight: Refactor backlight power on/off
  pwm-backlight: Improve readability
  ...
2013-11-16 12:21:40 -08:00
H Hartley Sweeten a230869817 pwm: add ep93xx PWM support
Remove the non-standard EP93xx PWM driver in drivers/misc and add
a new driver for the PWM controllers on the EP93xx platform based
on the PWM framework.

These PWM controllers each support 1 PWM channel with programmable
duty cycle, frequency, and polarity inversion.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2013-10-17 16:07:19 +02:00
Sudeep Dutt b170d8ce3f Intel MIC Host Driver for X100 family.
This patch enables the following:
a) Initializes the Intel MIC X100 PCIe devices.
b) Provides sysfs entries for family and stepping information.

Co-author: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Caz Yokoyama <Caz.Yokoyama@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Harshavardhan R Kharche <harshavardhan.r.kharche@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-26 13:49:23 -07:00
Linus Torvalds fc76a258d4 Driver core patches for 3.11-rc1
Here's the big driver core merge for 3.11-rc1
 
 Lots of little things, and larger firmware subsystem updates, all
 described in the shortlog.  Nice thing here is that we finally get rid
 of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
 been always on for a number of kernel releases, now it's just removed.)
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlHRsGMACgkQMUfUDdst+ylIIACfW8lLxOPVK+iYG699TWEBAkp0
 LFEAnjlpAMJ1JnoZCuWDZObNCev93zGB
 =020+
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg KH:
 "Here's the big driver core merge for 3.11-rc1

  Lots of little things, and larger firmware subsystem updates, all
  described in the shortlog.  Nice thing here is that we finally get rid
  of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
  been always on for a number of kernel releases, now it's just
  removed)"

* tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
  driver core: device.h: fix doc compilation warnings
  firmware loader: fix another compile warning with PM_SLEEP unset
  build some drivers only when compile-testing
  firmware loader: fix compile warning with PM_SLEEP set
  kobject: sanitize argument for format string
  sysfs_notify is only possible on file attributes
  firmware loader: simplify holding module for request_firmware
  firmware loader: don't export cache_firmware and uncache_firmware
  drivers/base: Use attribute groups to create sysfs memory files
  firmware loader: fix compile warning
  firmware loader: fix build failure with !CONFIG_FW_LOADER_USER_HELPER
  Documentation: Updated broken link in HOWTO
  Finally eradicate CONFIG_HOTPLUG
  driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests before suspend
  driver core: firmware loader: don't cache FW_ACTION_NOHOTPLUG firmware
  Documentation: Tidy up some drivers/base/core.c kerneldoc content.
  platform_device: use a macro instead of platform_driver_register
  firmware: move EXPORT_SYMBOL annotations
  firmware: Avoid deadlock of usermodehelper lock at shutdown
  dell_rbu: Select CONFIG_FW_LOADER_USER_HELPER explicitly
  ...
2013-07-02 11:44:19 -07:00
Jiri Slaby 4bb1667255 build some drivers only when compile-testing
Some drivers can be built on more platforms than they run on. This is
a burden for users and distributors who package a kernel. They have to
manually deselect some (for them useless) drivers when updating their
configs via oldconfig. And yet, sometimes it is even impossible to
disable the drivers without patching the kernel.

Introduce a new config option COMPILE_TEST and make all those drivers
to depend on the platform they run on, or on the COMPILE_TEST option.
Now, when users/distributors choose COMPILE_TEST=n they will not have
the drivers in their allmodconfig setups, but developers still can
compile-test them with COMPILE_TEST=y.

Now the drivers where we use this new option:
* PTP_1588_CLOCK_PCH: The PCH EG20T is only compatible with Intel Atom
  processors so it should depend on x86.
* FB_GEODE: Geode is 32-bit only so only enable it for X86_32.
* USB_CHIPIDEA_IMX: The OF_DEVICE dependency will be met on powerpc
  systems -- which do not actually support the hardware via that
  method.
* INTEL_MID_PTI: It is specific to the Penwell type of Intel Atom
  device.

[v2]
* remove EXPERT dependency

[gregkh - remove chipidea portion, as it's incorrect, and also doesn't
 apply to my driver-core tree]

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-geode@lists.infradead.org
Cc: linux-fbdev@vger.kernel.org
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: "Keller, Jacob E" <jacob.e.keller@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-24 16:41:32 -07:00
Andy Shevchenko 4cd5773a2a net: core: move mac_pton() to lib/net_utils.c
Since we have at least one user of this function outside of CONFIG_NET
scope, we have to provide this function independently. The proposed
solution is to move it under lib/net_utils.c with corresponding
configuration variable and select wherever it is needed.

Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-05 12:00:27 -07:00
Linus Torvalds 1e2f5b598a Merge branch 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 paravirt update from Ingo Molnar:
 "Various paravirtualization related changes - the biggest one makes
  guest support optional via CONFIG_HYPERVISOR_GUEST"

* 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, wakeup, sleep: Use pvops functions for changing GDT entries
  x86, xen, gdt: Remove the pvops variant of store_gdt.
  x86-32, gdt: Store/load GDT for ACPI S3 or hibernation/resume path is not needed
  x86-64, gdt: Store/load GDT for ACPI S3 or hibernate/resume path is not needed.
  x86: Make Linux guest support optional
  x86, Kconfig: Move PARAVIRT_DEBUG into the paravirt menu
2013-04-30 08:41:21 -07:00
Philipp Zabel 4984c6f5e5 misc: generic on-chip SRAM allocation driver
This driver requests and remaps a memory region as configured in the
device tree.  It serves memory from this region via the genalloc API.  It
optionally enables the SRAM clock.

Other drivers can retrieve the genalloc pool from a phandle pointing to
this drivers' device node in the device tree.

The allocation granularity is hard-coded to 32 bytes for now, to make the
SRAM driver useful for the 6502 remoteproc driver.  There is overhead for
bigger SRAMs, where only a much coarser allocation granularity is needed:
At 32 bytes minimum allocation size, a 256 KiB SRAM needs a 1 KiB bitmap
to track allocations.

[akpm@linux-foundation.org: fix Kconfig text, make sram_init static]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Huang Shijie <shijie8@gmail.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-04-29 18:28:13 -07:00
Arnd Bergmann 98097858cc misc: mark spear13xx-pcie-gadget as broken
This driver was merged in 2.6.38 but never actually compiled because
it depends on the <mach/pcie.h> header that has not made it into the
kernel. Starting with Linux-3.10, this results in "allyesconfig"
build errors, since spear13xx can now be enabled with the default
"multiplatform" platform on ARM. Let's mark it as broken for now.
If it doesn't get fixed, we can drop it completely.

Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-04-23 10:32:04 -07:00
Jiri Kosina 54f69b92f0 dummy-irq: introduce a dummy IRQ handler driver
This module accepts a single 'irq' parameter, which it should register for.

Its sole purpose is to help with debugging of IRQ sharing problems, by
force-enabling IRQ that would otherwise be disabled.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-25 13:22:32 -07:00
Borislav Petkov 6276a074c6 x86: Make Linux guest support optional
Put all config options needed to run Linux as a guest behind a
CONFIG_HYPERVISOR_GUEST menu so that they don't get built-in by default
but be selectable by the user. Also, make all units which depend on
x86_hyper, depend on this new symbol so that compilation doesn't fail
when CONFIG_HYPERVISOR_GUEST is disabled but those units assume its
presence.

Sort options in the new HYPERVISOR_GUEST menu, adapt config text and
drop redundant select.

Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1362428421-9244-3-git-send-email-bp@alien8.de
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
2013-03-04 13:14:25 -08:00
Linus Torvalds 7ed214ac20 Char/Misc driver patches for 3.9-rc1
Here's the big char/misc driver patches for 3.9-rc1.
 
 Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
 extcon, vmci, etc.).
 
 All of these have been in the linux-next tree for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
 x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
 =i5HH
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver patches from Greg Kroah-Hartman:
 "Here's the big char/misc driver patches for 3.9-rc1.

  Nothing major here, just lots of different driver updates (mei,
  hyperv, ipack, extcon, vmci, etc.).

  All of these have been in the linux-next tree for a while."

* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
  w1: w1_therm: Add force-pullup option for "broken" sensors
  w1: ds2482: Added 1-Wire pull-up support to the driver
  vme: add missing put_device() after device_register() fails
  extcon: max8997: Use workqueue to check cable state after completing boot of platform
  extcon: max8997: Set default UART/USB path on probe
  extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
  extcon: max8997: Set default of ADC debounce time during initialization
  extcon: max8997: Remove duplicate code related to set H/W line path
  extcon: max8997: Move defined constant to header file
  extcon: max77693: Make max77693_extcon_cable static
  extcon: max8997: Remove unreachable code
  extcon: max8997: Make max8997_extcon_cable static
  extcon: max77693: Remove unnecessary goto statement to improve readability
  extcon: max77693: Convert to devm_input_allocate_device()
  extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
  CREDITS: update email and address of Harald Hoyer
  extcon: arizona: Use MICDET for final microphone identification
  extcon: arizona: Always take the first HPDET reading as the final one
  extcon: arizona: Clear _trig_sts bits after jack detection
  extcon: arizona: Don't HPDET magic when headphones are enabled
  ...
2013-02-21 13:57:13 -08:00
Linus Torvalds 21eaab6d19 tty/serial patches for 3.9-rc1
Here's the big tty/serial driver patches for 3.9-rc1.
 
 More tty port rework and fixes from Jiri here, as well as lots of
 individual serial driver updates and fixes.
 
 All of these have been in the linux-next tree for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
 HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
 =vi6x
 -----END PGP SIGNATURE-----

Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial patches from Greg Kroah-Hartman:
 "Here's the big tty/serial driver patches for 3.9-rc1.

  More tty port rework and fixes from Jiri here, as well as lots of
  individual serial driver updates and fixes.

  All of these have been in the linux-next tree for a while."

* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
  tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
  serial: imx: fix uninitialized variable warning
  serial: tegra: assume CONFIG_OF
  TTY: do not update atime/mtime on read/write
  lguest: select CONFIG_TTY to build properly.
  ARM defconfigs: add missing inclusions of linux/platform_device.h
  fb/exynos: include platform_device.h
  ARM: sa1100/assabet: include platform_device.h directly
  serial: imx: Fix recursive locking bug
  pps: Fix build breakage from decoupling pps from tty
  tty: Remove ancient hardpps()
  pps: Additional cleanups in uart_handle_dcd_change
  pps: Move timestamp read into PPS code proper
  pps: Don't crash the machine when exiting will do
  pps: Fix a use-after free bug when unregistering a source.
  pps: Use pps_lookup_dev to reduce ldisc coupling
  pps: Add pps_lookup_dev() function
  tty: serial: uartlite: Support uartlite on big and little endian systems
  tty: serial: uartlite: Fix sparse and checkpatch warnings
  serial/arc-uart: Miscll DT related updates (Grant's review comments)
  ...

Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
2013-02-21 13:41:04 -08:00
Joe Millenbach 4f73bc4dd3 tty: Added a CONFIG_TTY option to allow removal of TTY
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48

Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-18 16:15:27 -08:00
Stefan Roese 781551df57 misc: Add Lattice ECP3 FPGA configuration via SPI
This patch adds support for bitstream configuration (programming /
loading) of the Lattice ECP3 FPGA's via the SPI bus.

Here an example on my custom MPC5200 based board:

$ echo 1 > /sys/class/firmware/spi0.0/loading
$ cat fpga_a4m2k.bit > /sys/class/firmware/spi0.0/data
$ echo 0 > /sys/class/firmware/spi0.0/loading

leads to these messages:

lattice-ecp3 spi0.0: FPGA Lattice ECP3-35 detected
lattice-ecp3 spi0.0: Configuring the FPGA...
lattice-ecp3 spi0.0: FPGA succesfully configured!

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-17 10:25:03 -08:00
George Zhang 20259849bb VMCI: Some header and config files.
VMCI head config patch Adds all the necessary files to enable building of the VMCI
module with the Linux Makefiles and Kconfig systems. Also adds the header files used
for building modules against the driver.

Signed-off-by: George Zhang <georgezhang@vmware.com>
Acked-by: Andy king <acking@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-08 16:15:57 -08:00
Joachim Eastwood f4319ff2bd ASoC: atmel-ssc: make it buildable on other architectures
Not very useful on non AT91/AVR32 platforms but it provides
more build coverage and prepares for ARM multiplatform.

Also fixes a truncated warning that would come when
building on a 64-bit arch.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-12-24 15:48:20 +00:00
Linus Torvalds 2474542f64 pwm: Changes for v3.7-rc1
All legacy PWM providers have now been moved to the PWM subsystem. The
 plan for 3.8 is to adapt all board files to provide a lookup table for
 PWM devices in order to get rid of the global namespace. Subsequently,
 users of the legacy pwm_request() and pwm_free() functions can be
 migrated to the new pwm_get() and pwm_put() functions. Once this has
 been completed, the legacy API and the compatibility code in the core
 can be removed.
 
 In addition to the above, these changes also add support for configuring
 the polarity of a PWM signal (currently only supported on ECAP and
 EHRPWM) and include a much needed rework of the i.MX driver. Managed
 functions to obtain and release a PWM device (devm_pwm_get() and
 devm_pwm_put()) have been added and the pwm-backlight driver has been
 updated to use them. If the PWM subsystem hasn't been enabled, dummy
 functions are provided that allow the subsystem to safely compile out.
 
 Some common checks on input parameters have been moved to the core and
 removed from the drivers. Finally, a small fix corrects the description
 of the PWM specifier's second cell in the device tree representation.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJQcV6pAAoJEN0jrNd/PrOh594P/3NHPjnTiyAZpUICX4mJeoMd
 1rX685HofCyX5jlHloS1pLRXYtIPZP97We5crNR/k/RujKcHAqAFzLtG2Jj93gxm
 nRUwLZ4xbrAgeaZeJV8YG1naWx9R1OjrK2sv+FyHRWsn9UZus2vDMV7tB0oNWo9k
 DMhtF1q7gQxx4nRu8z9FFybyItQinVREODNs+Gdv6AOJ36t+mOsGPL3LKZeFsIG3
 LdaB1p3t/07Job4KwGYYRjkOR7bIQ+ADnnO8Pkk0a9lxkMI8rA0uFbLwgyx7Hohh
 xZtm8R5il2IlHwqh52RzpShceWICxCZ3htuIXTRbVa1PSEsBzZ66W2CT7sy1jPm5
 lJlHgc7abaiwijtoG76I+Lgslv5UTViBuIYHSX4dH2kF3Jgm2SgTBNzZYePI5MMT
 BI3xc9WnwBpxgMybJsPHfU0Ff6O/9h9ab7q5lBOHkQJittahYxzWD+FgYlalcAa+
 I919iFREKNZytewLnXu+4TG0RfacQoj6D5G+SquOGmXyKYRhhJ1O6WodnRZHi/0n
 M6J0f6fLxpomI1RMn44VYP43OPJCDYxgXYoDLwCZQL9tSWYpdhXoDrjcIPO547w1
 ZS5HTXUE4DrxeYjoeqL555vtQIooM9CuH4JwKlz5zzea8NPC8eVtmNFTTWE6wKWX
 ZIOOLVvw/FI0/DSjBb8H
 =MQ5V
 -----END PGP SIGNATURE-----

Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm

Pull pwm changes from Thierry Reding:
 "All legacy PWM providers have now been moved to the PWM subsystem.
  The plan for 3.8 is to adapt all board files to provide a lookup table
  for PWM devices in order to get rid of the global namespace.
  Subsequently, users of the legacy pwm_request() and pwm_free()
  functions can be migrated to the new pwm_get() and pwm_put()
  functions.  Once this has been completed, the legacy API and the
  compatibility code in the core can be removed.

  In addition to the above, these changes also add support for
  configuring the polarity of a PWM signal (currently only supported on
  ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
  Managed functions to obtain and release a PWM device (devm_pwm_get()
  and devm_pwm_put()) have been added and the pwm-backlight driver has
  been updated to use them.  If the PWM subsystem hasn't been enabled,
  dummy functions are provided that allow the subsystem to safely
  compile out.

  Some common checks on input parameters have been moved to the core and
  removed from the drivers.  Finally, a small fix corrects the
  description of the PWM specifier's second cell in the device tree
  representation."

* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
  pwm: dt: Fix description of second PWM cell
  pwm: Check for negative duty-cycle and period
  pwm: Add Ingenic JZ4740 support
  MIPS: JZ4740: Export timer API
  pwm: Move PUV3 PWM driver to PWM framework
  unicore32: pwm: Use managed resource allocations
  unicore32: pwm: Remove unnecessary indirection
  unicore32: pwm: Use module_platform_driver()
  unicore32: pwm: Properly remap memory-mapped registers
  pwm-backlight: Use devm_pwm_get() instead of pwm_get()
  pwm: Move AB8500 PWM driver to PWM framework
  pwm: Fix compilation error when CONFIG_PWM is not defined
  pwm: i.MX: fix clock lookup
  pwm: i.MX: use per clock unconditionally
  pwm: i.MX: add devicetree support
  pwm: i.MX: Use module_platform_driver
  pwm: i.MX: add functions to enable/disable pwm.
  pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
  pwm: i.MX: factor out SoC specific functions
  pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
  ...
2012-10-10 20:15:24 +09:00
Thierry Reding 6173f8f4ed pwm: Move AB8500 PWM driver to PWM framework
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arun Murthy <arun.murthy@stericsson.com>
2012-09-20 12:52:03 +02:00
Greg Kroah-Hartman 65929215d8 char/misc: remove CONFIG_EXPERIMENTAL dependencies
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.

Cc: Kees Cook <keescook@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-09-18 16:14:53 +01:00
Linus Torvalds 9ec97169e7 Merge branch 'for-3.6' of git://gitorious.org/linux-pwm/linux-pwm
Pull PWM subsystem from Thierry Reding:
 "The new PWM subsystem aims at collecting all implementations of the
  legacy PWM API and to eventually replace it completely.

  The subsystem has been in development for over half a year now and
  many drivers have already been converted.  It has been in linux-next
  for a couple of weeks and there have been no major issues so I think
  it is ready for inclusion in your tree."

Arnd Bergmann <arnd@arndb.de>:
 "Very much Ack on the new subsystem.  It uses the interface
  declarations as the previously separate pwm drivers, so nothing
  changes for now in the drivers using it, although it enables us to
  change those more easily in the future if we want to.

  This work is also one of the missing pieces that are required to
  eventually build ARM kernels for multiple platforms, which is
  currently prohibited (amongs other things) by the fact that you cannot
  have more than one driver exporting the pwm functions."

Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Philip, Avinash <avinashphilip@ti.com> # TI's AM33xx platforms
Acked-By: Alexandre Pereira da Silva <aletes.xgr@gmail.com> # LPC32XX
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>

Fix up trivial conflicts with other cleanups and DT updates.

* 'for-3.6' of git://gitorious.org/linux-pwm/linux-pwm: (36 commits)
  pwm: pwm-tiehrpwm: PWM driver support for EHRPWM
  pwm: pwm-tiecap: PWM driver support for ECAP APWM
  pwm: fix used-uninitialized warning in pwm_get()
  pwm: add lpc32xx PWM support
  pwm_backlight: pass correct brightness to callback
  pwm: Use pr_* functions in pwm-samsung.c file
  pwm: Convert pwm-samsung to use devm_* APIs
  pwm: Convert pwm-tegra to use devm_clk_get()
  pwm: pwm-mxs: Return proper error if pwmchip_remove() fails
  pwm: pwm-bfin: Return proper error if pwmchip_remove() fails
  pwm: pxa: Propagate pwmchip_remove() error
  pwm: Convert pwm-pxa to use devm_* APIs
  pwm: Convert pwm-vt8500 to use devm_* APIs
  pwm: Convert pwm-imx to use devm_* APIs
  pwm: Conflict with legacy PWM API
  pwm: pwm-mxs: add pinctrl support
  pwm: pwm-mxs: use devm_* managed functions
  pwm: pwm-mxs: use global reset function stmp_reset_block
  pwm: pwm-mxs: encode soc name in compatible string
  pwm: Take over maintainership of the PWM subsystem
  ...
2012-07-30 09:22:37 -07:00
Thierry Reding eac7a92fd0 pwm: Conflict with legacy PWM API
In order to avoid duplicate symbols with legacy PWM API implementations,
the new PWM framework needs to conflict with any of the existing legacy
implementations. This is done in two ways: for implementations provided
by drivers, a conflict is added to the driver to ensure it will have to
be ported to the PWM subsystem before it can coexist with other PWM
providers. For architecture-specific code, the conflict is added to the
PWM symbol to avoid confusion when a previously picked platform or
machine can no longer be selected because of the PWM subsystem being
included.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-07-23 13:23:56 +02:00
John W. Linville ce8126c334 iwmc3200top: remove driver for unavailable hardware
This hardware never became available to normal humans.  Leaving this
driver imposes unwelcome maintenance costs for no clear benefit.

Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-11 15:40:22 -04:00
Linus Torvalds fb09bafda6 Staging tree pull request for 3.5-rc1
Here is the big staging tree pull request for the 3.5-rc1 merge window.
 
 Loads of changes here, and we just narrowly added more lines than we
 added:
  622 files changed, 28356 insertions(+), 26059 deletions(-)
 
 But, good news is that there is a number of subsystems that moved out of
 the staging tree, to their respective "real" portions of the kernel.
 
 Code that moved out was:
 	- iio core code
 	- mei driver
 	- vme core and bridge drivers
 
 There was one broken network driver that moved into staging as a step
 before it is removed from the tree (pc300), and there was a few new
 drivers added to the tree:
 	- new iio drivers
 	- gdm72xx wimax USB driver
 	- ipack subsystem and 2 drivers
 
 All of the movements around have acks from the various subsystem
 maintainers, and all of this has been in the linux-next tree for a
 while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iEYEABECAAYFAk+7q8MACgkQMUfUDdst+ymjogCguo8fANFVlPWeZGeoBTL+aQfQ
 yTkAoLE0codmh+2SvhulYgyU1Wh6ZDK2
 =nJ2F
 -----END PGP SIGNATURE-----

Merge tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging tree changes from Greg Kroah-Hartman:
 "Here is the big staging tree pull request for the 3.5-rc1 merge
  window.

  Loads of changes here, and we just narrowly added more lines than we
  added:
   622 files changed, 28356 insertions(+), 26059 deletions(-)

  But, good news is that there is a number of subsystems that moved out
  of the staging tree, to their respective "real" portions of the
  kernel.

  Code that moved out was:
	- iio core code
	- mei driver
	- vme core and bridge drivers

  There was one broken network driver that moved into staging as a step
  before it is removed from the tree (pc300), and there was a few new
  drivers added to the tree:
	- new iio drivers
	- gdm72xx wimax USB driver
	- ipack subsystem and 2 drivers

  All of the movements around have acks from the various subsystem
  maintainers, and all of this has been in the linux-next tree for a
  while.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fixed up various trivial conflicts, along with a non-trivial one found
in -next and pointed out by Olof Johanssen: a clean - but incorrect -
merge of the arch/arm/boot/dts/at91sam9g20.dtsi file.  Fix up manually
as per Stephen Rothwell.

* tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (536 commits)
  Staging: bcm: Remove two unused variables from Adapter.h
  Staging: bcm: Removes the volatile type definition from Adapter.h
  Staging: bcm: Rename all "INT" to "int" in Adapter.h
  Staging: bcm: Fix warning: __packed vs. __attribute__((packed)) in Adapter.h
  Staging: bcm: Correctly format all comments in Adapter.h
  Staging: bcm: Fix all whitespace issues in Adapter.h
  Staging: bcm: Properly format braces in Adapter.h
  Staging: ipack/bridges/tpci200: remove unneeded casts
  Staging: ipack/bridges/tpci200: remove TPCI200_SHORTNAME constant
  Staging: ipack: remove board_name and bus_name fields from struct ipack_device
  Staging: ipack: improve the register of a bus and a device in the bus.
  staging: comedi: cleanup all the comedi_driver 'detach' functions
  staging: comedi: remove all 'default N' in Kconfig
  staging: line6/config.h: Delete unused header
  staging: gdm72xx depends on NET
  staging: gdm72xx: Set up parent link in sysfs for gdm72xx devices
  staging: drm/omap: initial dmabuf/prime import support
  staging: drm/omap: dmabuf/prime mmap support
  pstore/ram: Add ECC support
  pstore/ram: Switch to persistent_ram routines
  ...
2012-05-22 16:34:21 -07:00
Linus Torvalds 5d4e2d08e7 Driver core pull for 3.5-rc1
Here's the driver core, and other driver subsystems, pull request for
 the 3.5-rc1 merge window.
 
 Outside of a few minor driver core changes, we ended up with the
 following different subsystem and core changes as well, due to
 interdependancies on the driver core:
  - hyperv driver updates
  - drivers/memory being created and some drivers moved into it
  - extcon driver subsystem created out of the old Android staging switch
    driver code
  - dynamic debug updates
  - printk rework, and /dev/kmsg changes
 
 All of this has been tested in the linux-next releases for a few weeks
 with no reported problems.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
 VOQAnAriySv397St36J6Hz5bMQZwB1Yq
 =SQc+
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg Kroah-Hartman:
 "Here's the driver core, and other driver subsystems, pull request for
  the 3.5-rc1 merge window.

  Outside of a few minor driver core changes, we ended up with the
  following different subsystem and core changes as well, due to
  interdependancies on the driver core:
   - hyperv driver updates
   - drivers/memory being created and some drivers moved into it
   - extcon driver subsystem created out of the old Android staging
     switch driver code
   - dynamic debug updates
   - printk rework, and /dev/kmsg changes

  All of this has been tested in the linux-next releases for a few weeks
  with no reported problems.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.

* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
  uio_pdrv_genirq: get irq through platform resource if not set otherwise
  memory: tegra{20,30}-mc: Remove empty *_remove()
  printk() - isolate KERN_CONT users from ordinary complete lines
  sysfs: get rid of some lockdep false positives
  Drivers: hv: util: Properly handle version negotiations.
  Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
  memory: tegra{20,30}-mc: Use dev_err_ratelimited()
  driver core: Add dev_*_ratelimited() family
  Driver Core: don't oops with unregistered driver in driver_find_device()
  printk() - restore prefix/timestamp printing for multi-newline strings
  printk: add stub for prepend_timestamp()
  ARM: tegra30: Make MC optional in Kconfig
  ARM: tegra20: Make MC optional in Kconfig
  ARM: tegra30: MC: Remove unnecessary BUG*()
  ARM: tegra20: MC: Remove unnecessary BUG*()
  printk: correctly align __log_buf
  ARM: tegra30: Add Tegra Memory Controller(MC) driver
  ARM: tegra20: Add Tegra Memory Controller(MC) driver
  printk() - restore timestamp printing at console output
  printk() - do not merge continuation lines of different threads
  ...
2012-05-22 16:02:13 -07:00
Chanwoo Choi 6a7e2618b3 misc: MAX8997: Remove max8997-muic driver
This patch remove old max8997-muic drvier because of newly Extcon framework.
Extcon framework manages the external connector, so add extcon-max8997 driver
by using Extcon interface to support MUIC feature of Maxim 8997 PMIC instead
of max8997-muic driver(drivers/misc/max8997-muic.c).

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-09 15:15:59 -07:00
Greg Kroah-Hartman ffc2825c29 Staging: mei: move the mei code out of staging
It's been cleaned up, and there's nothing else left to do, so move it
out of staging into drivers/misc/ where all can use it now.

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Oren Weil <oren.jer.weil@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-01 18:23:38 -04:00
Eric Andersson 985087dbcb misc: add support for bmp18x chips to the bmp085 driver
The bmp18x chip family comes in an I2C respectively SPI variant.
Hence, the bmp085 driver was split to support both buses.

Tested-by: Zhengguang Guo <zhengguang.guo@bosch-sensortec.com>
Reviewed-by: Stefan Nilsson <stefan.nilsson@unixphere.com>
Signed-off-by: Eric Andersson <eric.andersson@unixphere.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-18 14:57:14 -07:00
Fabio Estevam 7c5763b845 drivers: misc: Remove MISC_DEVICES config option
MISC_DEVICES option alone does not select any kernel code and can cause dependency build warnings, such as:

warning: (KS8851 && AX88796_93CX6 && RTL8180 && RTL8187 && ADM8211 && RT2400PCI && RT2500PCI && RT61PCI && RT2800PCI && R8187SE) selects EEPROM_93CX6 which has unmet direct dependencies (MISC_DEVICES)

As the current drivers/misc/Kconfig stands, it is only possible to select the drivers below if MISC_DEVICES option is selected:

source "drivers/misc/c2port/Kconfig"
source "drivers/misc/eeprom/Kconfig"
source "drivers/misc/cb710/Kconfig"
source "drivers/misc/iwmc3200top/Kconfig"
source "drivers/misc/ti-st/Kconfig"
source "drivers/misc/lis3lv02d/Kconfig"
source "drivers/misc/carma/Kconfig"
source "drivers/misc/altera-stapl/Kconfig"

So remove MISC_DEVICES option so that nothing is dependant on it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-24 16:24:02 -08:00
Donggeun Kim 99f09bebbe misc: Add driver support for MAX8997 MUIC
The MUIC function in MAX8997 device can be used as
a USB port detector and switch.
This patch supports the MUIC feature of MAX8997.

Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:32 +01:00
Tomoya MORINAGA 584ad00ce4 pch_phub: Support new device LAPIS Semiconductor ML7831 IOH
ML7831 is companion chip for Intel Atom E6xx series.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15 11:01:48 -08:00
Linus Torvalds 68e24ba704 Merge branch 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
  ARM: pxa/cm-x300: properly set bt_reset pin
  ARM: mmp: rename SHEEVAD to GPLUGD
  ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
  ARM: i.MX28: shift frac value in _CLK_SET_RATE
  plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
  ARM: mx5: fix clock usage for suspend
  ARM: pxa: use correct __iomem annotations
  ARM: pxa: sharpsl pm needs SPI
  ARM: pxa: centro and treo680 need palm27x
  ARM: pxa: make pxafb_smart_*() empty when not enabled
  ARM: pxa: select POWER_SUPPLY on raumfeld
  ARM: pxa: pxa95x is incompatible with earlier pxa
  ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
  ARM: pxa: pxa95x/saarb depends on pxa3xx code
  ARM: pxa: allow selecting just one of TREO680/CENTRO
  ARM: pxa: export symbols from pxa3xx-ulpi
  ARM: pxa: make zylonite_pxa*_init declaration match code
  ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
  ARM: at91: add defconfig for at91sam9g45 family
  ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
  ...
2011-11-01 19:55:06 -07:00
Nicolas Ferre 2d60cd15d4 ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
Remove dependency line which was not including the SAM9G45.

[arnd: added dependency on HAVE_CLK to avoid breaking other machines]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-10-07 17:39:19 +02:00