Separating discards and zeroout operations allows us to remove the LBPRZ
block zeroing constraints from discards and honor the device preferences
for UNMAP commands.
If supported by the device, we'll also choose UNMAP over one of the
WRITE SAME variants for discards.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that zeroout and discards are distinct operations we need to
separate the policy of choosing the appropriate command. Create a
zeroing_mode which can be one of:
write: Zeroout assist not present, use regular WRITE
writesame: Allow WRITE SAME(10/16) with a zeroed payload
writesame_16_unmap: Allow WRITE SAME(16) with UNMAP
writesame_10_unmap: Allow WRITE SAME(10) with UNMAP
The last two are conditional on the device being thin provisioned with
LBPRZ=1 and LBPWS=1 or LBPWS10=1 respectively.
Whether to set the UNMAP bit or not depends on the REQ_NOUNMAP flag. And
if none of the _unmap variants are supported, regular WRITE SAME will be
used if the device supports it.
The zeroout_mode is exported in sysfs and the detected mode for a given
device can be overridden using the string constants above.
With this change in place we can now issue WRITE SAME(16) with UNMAP set
for block zeroing applications that require hard guarantees and
logical_block_size granularity. And at the same time use the UNMAP
command with the device's preferred granulary and alignment for discard
operations.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It seems like DRBD assumes its on the wire TRIM request always zeroes data.
Use that fact to implement REQ_OP_WRITE_ZEROES.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
drbd always wants its discard wire operations to zero the blocks, so
use blkdev_issue_zeroout with the BLKDEV_ZERO_UNMAP flag instead of
reinventing it poorly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we have REQ_OP_WRITE_ZEROES implemented for all devices that
support efficient zeroing, we can remove the call to blkdev_issue_discard.
This means we only have two ways of zeroing left and can simplify the
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
mmc only supports discarding on large alignments, so the zeroing code
would always fall back to explicit writings of zeroes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
rsxx only supports discarding on large alignments, so the zeroing code
would always fall back to explicit writings of zeroes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
rbd only supports discarding on large alignments, so the zeroing code
would always fall back to explicit writings of zeroes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's just a in-driver reimplementation of writing zeroes to the pages,
which fails if the discards aren't page aligned.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's identical to discard as hole punches will always leave us with
zeroes on reads.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Just the same as discard if the block size equals the system page size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
But now for the real NVMe Write Zeroes yet, just to get rid of the
discard abuse for zeroing. Also rename the quirk flag to be a bit
more self-explanatory.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Try to use a write same with unmap bit variant if the device supports it
and the caller allows for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This gets us support for non-discard efficient write of zeroes (e.g. NVMe)
and prepares for removing the discard_zeroes_data flag.
Also remove a pointless discard support check, which is done in
blkdev_issue_discard already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This avoids fallbacks to explicit zeroing in (__)blkdev_issue_zeroout if
the caller doesn't want them.
Also clean up the convoluted check for the return condition that this
new flag is added to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If this flag is set logical provisioning capable device should
release space for the zeroed blocks if possible, if it is not set
devices should keep the blocks anchored.
Also remove an out of sync kerneldoc comment for a static function
that would have become even more out of data with this change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Turn the existing discard flag into a new BLKDEV_ZERO_UNMAP flag with
similar semantics, but without referring to diѕcard.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We'll always use the WRITE ZEROES code for zeroing now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It seems like the code currently passes whatever it was using for writes
to WRITE SAME. Just switch it to WRITE ZEROES, although that doesn't
need any payload.
Untested, and confused by the code, maybe someone who understands it
better than me can help..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy & paste from the REQ_OP_WRITE_SAME code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix up do_region to not allocate a bio_vec for discards. We've
got rid of the discard payload allocated by the caller years ago.
Obviously this wasn't actually harmful given how long it's been
there, but it's still good to avoid the pointless allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy & paste from the REQ_OP_WRITE_SAME code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy and past the REQ_OP_WRITE_SAME code to prepare to implementations
that limit the write zeroes size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make life easy for implementations that needs to send a data buffer
to the device (e.g. SCSI) by numbering it as a data out command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Split sd_setup_discard_cmnd into one function per provisioning type. While
this creates some very slight duplication of boilerplate code it keeps the
code modular for additions of new provisioning types, and for reusing the
write same functions for the upcoming scsi implementation of the Write Zeroes
operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Lets not flood the kernel log with messages unless
the user requests so.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The blk_mq_dispatch_rq_list() implementation got modified several
times but the comments in that function were not updated every
time. Since it is nontrivial what is going on, update the comments
in blk_mq_dispatch_rq_list().
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since the next patch in this series will use RCU to iterate over
tag_list, make this safe. Add lockdep_assert_held() statements
in functions that iterate over tag_list to make clear that using
list_for_each_entry() instead of list_for_each_entry_rcu() is
fine in these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Minor cleanup that makes it easier to figure out what's going on in the
driver tag allocation failure path of blk_mq_dispatch_rq_list().
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Schedulers need to be informed when a hardware queue is added or removed
at runtime so they can allocate/free per-hardware queue data. So,
replace the blk_mq_sched_init_hctx_data() helper, which only makes sense
at init time, with .init_hctx() and .exit_hctx() hooks.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We've added a considerable amount of fixes for stalls and issues
with the blk-mq scheduling in the 4.11 series since forking
off the for-4.12/block branch. We need to do improvements on
top of that for 4.12, so pull in the previous fixes to make
our lives easier going forward.
Signed-off-by: Jens Axboe <axboe@fb.com>
To improve scalability, if hardware queues are shared, restart
a single hardware queue in round-robin fashion. Rename
blk_mq_sched_restart_queues() to reflect the new semantics.
Remove blk_mq_sched_mark_restart_queue() because this function
has no callers. Remove flag QUEUE_FLAG_RESTART because this
patch removes the code that uses this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
While running the srp-test software I noticed that request
processing stalls sporadically at the beginning of a test, namely
when mkfs is run against a dm-mpath device. Every time when that
happened the following command was sufficient to resume request
processing:
echo run >/sys/kernel/debug/block/dm-0/state
This patch avoids that such request processing stalls occur. The
test I ran is as follows:
while srp-test/run_tests -d -r 30 -t 02-mq; do :; done
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Jens Axboe <axboe@fb.com>
If a .queue_rq() function returns BLK_MQ_RQ_QUEUE_BUSY then the block
driver that implements that function is responsible for rerunning the
hardware queue once requests can be queued again successfully.
commit 52d7f1b5c2 ("blk-mq: Avoid that requeueing starts stopped
queues") removed the blk_mq_stop_hw_queue() call from scsi_queue_rq()
for the BLK_MQ_RQ_QUEUE_BUSY case. Hence change all calls to functions
that are intended to rerun a busy queue such that these examine all
hardware queues instead of only stopped queues.
Since no other functions than scsi_internal_device_block() and
scsi_internal_device_unblock() should ever stop or restart a SCSI
queue, change the blk_mq_delay_queue() call into a
blk_mq_delay_run_hw_queue() call.
Fixes: commit 52d7f1b5c2 ("blk-mq: Avoid that requeueing starts stopped queues")
Fixes: commit 7e79dadce2 ("blk-mq: stop hardware queue in blk_mq_delay_queue()")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Introduce a function that runs a hardware queue unconditionally
after a delay. Note: there is already a function that stops and
restarts a hardware queue after a delay, namely blk_mq_delay_queue().
This function will be used in the next patch in this series.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Long Li <longli@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently only dm and md/raid5 bios trigger
trace_block_bio_complete(). Now that we have bio_chain() and
bio_inc_remaining(), it is not possible, in general, for a driver to
know when the bio is really complete. Only bio_endio() knows that.
So move the trace_block_bio_complete() call to bio_endio().
Now trace_block_bio_complete() pairs with trace_block_bio_queue().
Any bio for which a 'queue' event is traced, will subsequently
generate a 'complete' event.
There are a few cases where completion tracing is not wanted.
1/ If blk_update_request() has already generated a completion
trace event at the 'request' level, there is no point generating
one at the bio level too. In this case the bi_sector and bi_size
will have changed, so the bio level event would be wrong
2/ If the bio hasn't actually been queued yet, but is being aborted
early, then a trace event could be confusing. Some filesystems
call bio_endio() but do not want tracing.
3/ The bio_integrity code interposes itself by replacing bi_end_io,
then restoring it and calling bio_endio() again. This would produce
two identical trace events if left like that.
To handle these, we introduce a flag BIO_TRACE_COMPLETION and only
produce the trace event when this is set.
We address point 1 above by clearing the flag in blk_update_request().
We address point 2 above by only setting the flag when
generic_make_request() is called.
We address point 3 above by clearing the flag after generating a
completion event.
When bio_split() is used on a bio, particularly in blk_queue_split(),
there is an extra complication. A new bio is split off the front, and
may be handle directly without going through generic_make_request().
The old bio, which has been advanced, is passed to
generic_make_request(), so it will trigger a trace event a second
time.
Probably the best result when a split happens is to see a single
'queue' event for the whole bio, then multiple 'complete' events - one
for each component. To achieve this was can:
- copy the BIO_TRACE_COMPLETION flag to the new bio in bio_split()
- avoid generating a 'queue' event if BIO_TRACE_COMPLETION is already set.
This way, the split-off bio won't create a queue event, the original
won't either even if it re-submitted to generic_make_request(),
but both will produce completion events, each for their own range.
So if generic_make_request() is called (which generates a QUEUED
event), then bi_endio() will create a single COMPLETE event for each
range that the bio is split into, unless the driver has explicitly
requested it not to.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The comment for the 'flags' field of 'bio' mentions
"command" which is no longer stored there, and doesn't
mention the bvec pool number, which is.
BIO_RESET_BITS is set in such a way that it would need to be
updated if new bits were added, which is easy to miss.
BVEC_POOL_BITS is larger than needed. The BVEC_POOL_IDX()
ranges from 0 to 6, so 3 bits are sufficient.
This patch make improvements in each of these areas.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_update_nr_hw_queues() used to remap hardware queues, which is the
behavior that drivers expect. However, commit 4e68a01142 changed
blk_mq_queue_reinit() to not remap queues for the case of CPU
hotplugging, inadvertently making blk_mq_update_nr_hw_queues() not remap
queues as well. This breaks, for example, NBD's multi-connection mode,
leaving the added hardware queues unused. Fix it by making
blk_mq_update_nr_hw_queues() explicitly remap the queues.
Fixes: 4e68a01142 ("blk-mq: don't redistribute hardware queues on a CPU hotplug event")
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In elevator_switch(), if blk_mq_init_sched() fails, we attempt to fall
back to the original scheduler. However, at this point, we've already
torn down the original scheduler's tags, so this causes a crash. Doing
the fallback like the legacy elevator path is much harder for mq, so fix
it by just falling back to none, instead.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a new hardware queue is added at runtime, we don't allocate scheduler
tags for it, leading to a crash. This hooks up the scheduler framework
to blk_mq_{init,exit}_hctx() to make sure everything gets properly
initialized/freed.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Preparation cleanup for the next couple of fixes, push
blk_mq_sched_setup() and e->ops.mq.init_sched() into a helper.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
While dispatching requests, if we fail to get a driver tag, we mark the
hardware queue as waiting for a tag and put the requests on a
hctx->dispatch list to be run later when a driver tag is freed. However,
blk_mq_dispatch_rq_list() may dispatch requests from multiple hardware
queues if using a single-queue scheduler with a multiqueue device. If
blk_mq_get_driver_tag() fails, it doesn't update the hardware queue we
are processing. This means we end up using the hardware queue of the
previous request, which may or may not be the same as that of the
current request. If it isn't, the wrong hardware queue will end up
waiting for a tag, and the requests will be on the wrong dispatch list,
leading to a hang.
The fix is twofold:
1. Make sure we save which hardware queue we were trying to get a
request for in blk_mq_get_driver_tag() regardless of whether it
succeeds or not.
2. Make blk_mq_dispatch_rq_list() take a request_queue instead of a
blk_mq_hw_queue to make it clear that it must handle multiple
hardware queues, since I've already messed this up on a couple of
occasions.
This didn't appear in testing with nvme and mq-deadline because nvme has
more driver tags than the default number of scheduler tags. However,
with the blk_mq_update_nr_hw_queues() fix, it showed up with nbd.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After commit 64c7f1d157, we went from 1 to 2 holes in my
test setup. If we move the timeout field a bit, we remove
both of those holes and shrink struct request by 8 bytes.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of bloating the generic struct request with it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The way NVMe uses this field is entirely different from the older
SCSI/BLOCK_PC usage, so move it into struct nvme_request.
Also reduce the size of the file to a unsigned char so that we leave
space for additional smaller fields that will appear soon.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't pass the status explicitly but derive it from the requeust,
and unwind the complex condition to be more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Martin K. Petersen
Christoph Hellwig
Scott Bauer
Bart Van Assche
Omar Sandoval
Jens Axboe
NeilBrown