Program the SDRC_MR_0 register as well during SDRC clock changes.
This register allows selection of the memory CAS latency. Some SDRAM
chips, such as the Qimonda HYB18M512160AF6, have a lower CAS latency
at lower clock rates.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2
divider, add a short delay before returning to SDRAM to allow the SDRC
time to stabilize. Without this delay, the system is prone to random
panics upon re-entering SDRAM.
This time delay varies based on MPU frequency. At 500MHz MPU frequency at
room temperature, 64 loops seems to work okay; so add another 32 loops for
environmental and process variation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On the OMAP3, initialize SDRC timings when the kernel boots. This ensures
that the kernel is running with known, optimized SDRC timings, rather than
whatever was configured by the bootloader.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The original CDP kernel that this code comes from waited for 0x800
loops after switching the CORE DPLL M2 divider. This does not appear
to be necessary.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: convert page/tlb to asm-generic
Blackfin: convert types to asm-generic
Blackfin: convert irq/process to asm-generic
Blackfin: convert signal/mmap to asm-generic
Blackfin: convert locking primitives to asm-generic
Blackfin: convert termios to asm-generic
Blackfin: convert simple headers to asm-generic
Blackfin: convert socket/poll to asm-generic
Blackfin: convert user/elf to asm-generic
Blackfin: convert shm/sysv/ipc to asm-generic
Blackfin: convert asm/ioctls.h to asm-generic/ioctls.h
Blackfin: only build irqpanic.c when needed
Blackfin: pull in asm/io.h in ksyms for prototypes
Blackfin: use common test_bit() rather than __test_bit()
This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for
PIXIS' sdcsr bank that is used for managing SPI chip-select and for
reading card's states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch supports the cache handling for some old Feroceon cores for
which the CPU ID is like 0x41159260. This is a complement to
commit ab6d15d506.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
When a kthread function returns, it branches to do_exit(). However, the
unwinding information isn't valid anymore and any stack trace caused by
do_exit() may be incorrect. This patch adds a kernel_thread_exit()
function and annotated with '.cantunwind' so that the unwinder stops
when reaching it.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are situations where the unwinder goes beyond stack boundaries and
unwinds random data. This patch moves the stack boundaries check after
the unwind_exec_insn() call and adds an extra check for possible
infinite loops (like "mov pc, lr" with pc == lr).
The patch also fixes a bug in the unwind instructions interpreter. The
0xb0 instruction can only set PC to LR if this wasn't already set by
a previous instruction (this is used on exceptions taken while in kernel
mode where svc_entry is annotated with ".save {r0 - pc}").
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Not discarding these sections when hotplug isn't available prevents the
kernel from building.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Min Zhang <mzhang@mvista.com>
Add alignment fault fixup support for 32-bit Thumb-2 LDM, LDRD, POP,
PUSH, STM and STRD instructions. Alignment fault fixup support for
the remaining 32-bit Thumb-2 load/store instruction cases is not
included since ARMv6 and later processors include hardware support
for loads and stores of unaligned words and halfwords.
Signed-off-by: Min Zhang <mzhang@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Improve a few details in perfcounter call-chain recording that
makes use of fast-GUP:
- Use ACCESS_ONCE() to observe the pte value. ptes are fundamentally
racy and can be changed on another CPU, so we have to be careful
about how we access them. The PAE branch is already careful with
read-barriers - but the non-PAE and 64-bit side needs an
ACCESS_ONCE() to make sure the pte value is observed only once.
- make the checks a bit stricter so that we can feed it any kind of
cra^H^H^H user-space input ;-)
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The cpu member of struct irq_desc was recently renamed to node. The
patch renames the ARM references to the old member.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This header file is needed for twd_base.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before exposing upstream tools to a callchain-samples ABI, tidy it
up to make it more extensible in the future:
Use markers in the IP chain to denote context, use (u64)-1..-4095 range
for these context markers because we use them for ERR_PTR(), so these
addresses are unlikely to be mapped.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit b696fdc259 ("sparc64: Defer
cpu_data() setup until end of per-cpu data initialization.") broke
bootup for UP builds because the cpu_data() initialization only
occurs in setup_per_cpu_areas() which is never compiled in nor
called in UP builds.
Fix this up by calling the setups directly from init_64.c when
non-SMP.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irq_panic function is only used when CONFIG_DEBUG_ICACHE_CHECK is
enabled, so move the conditional build to the Makefile rather than
wrapping all of the contents of the file.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we pull in asm/io.h when exporting symbols for the I/O functions
so we don't end up with a build failure due to missing prototypes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert to test_bit() as that is what pretty much everyone uses and allows
us to migrate asm/bitops.h to the asm-generic version.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In case gcc does something funny with the stack frames, or the return
from function code, we would like to detect that.
An arch may implement passing of a variable that is unique to the
function and can be saved on entering a function and can be tested
when exiting the function. Usually the frame pointer can be used for
this purpose.
This patch also implements this for x86. Where it passes in the stack
frame of the parent function, and will test that frame on exit.
There was a case in x86_32 with optimize for size (-Os) where, for a
few functions, gcc would align the stack frame and place a copy of the
return address into it. The function graph tracer modified the copy and
not the actual return address. On return from the funtion, it did not go
to the tracer hook, but returned to the parent. This broke the function
graph tracer, because the return of the parent (where gcc did not do
this funky manipulation) returned to the location that the child function
was suppose to. This caused strange kernel crashes.
This test detected the problem and pointed out where the issue was.
This modifies the parameters of one of the functions that the arch
specific code calls, so it includes changes to arch code to accommodate
the new prototype.
Note, I notice that the parsic arch implements its own push_return_trace.
This is now a generic function and the ftrace_push_return_trace should be
used instead. This patch does not touch that code.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (56 commits)
sh: Fix declaration of __kernel_sigreturn and __kernel_rt_sigreturn
sh: Enable soc-camera in ap325rxa/migor/se7724 defconfigs.
sh: remove stray markers.
sh: defconfig updates.
sh: pci: Initial PCI-Express support for SH7786 Urquell board.
sh: Generic HAVE_PERF_COUNTER support.
SH: convert migor to soc-camera as platform-device
SH: convert ap325rxa to soc-camera as platform-device
soc-camera: unify i2c camera device platform data
sh: add platform data for r8a66597-hcd in setup-sh7723
sh: add platform data for r8a66597-hcd in setup-sh7366
sh: x3proto: add platform data for r8a66597-hcd
sh: highlander: add platform data for r8a66597-hcd
sh: sh7785lcr: add platform data for r8a66597-hcd
sh: turn off irqs when disabling CMT/TMU timers
sh: use kzalloc() for cpg clocks
sh: unbreak WARN_ON()
sh: Use generic atomic64_t implementation.
sh: Revised clock function in highlander
sh: Update r7780mp defconfig
...
Add support for new relocs which may show up in MN10300 kernel modules due to
linker relaxation.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable gcov profiling of the entire kernel on x86_64. Required changes
include disabling profiling for:
* arch/kernel/acpi/realmode and arch/kernel/boot/compressed:
not linked to main kernel
* arch/vdso, arch/kernel/vsyscall_64 and arch/kernel/hpet:
profiling causes segfaults during boot (incompatible context)
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable the use of GCC's coverage testing tool gcov [1] with the Linux
kernel. gcov may be useful for:
* debugging (has this code been reached at all?)
* test improvement (how do I change my test to cover these lines?)
* minimizing kernel configurations (do I need this option if the
associated code is never run?)
The profiling patch incorporates the following changes:
* change kbuild to include profiling flags
* provide functions needed by profiling code
* present profiling data as files in debugfs
Note that on some architectures, enabling gcc's profiling option
"-fprofile-arcs" for the entire kernel may trigger compile/link/
run-time problems, some of which are caused by toolchain bugs and
others which require adjustment of architecture code.
For this reason profiling the entire kernel is initially restricted
to those architectures for which it is known to work without changes.
This restriction can be lifted once an architecture has been tested
and found compatible with gcc's profiling. Profiling of single files
or directories is still available on all platforms (see config help
text).
[1] http://gcc.gnu.org/onlinedocs/gcc/Gcov.html
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the number of cells for the values of CPC925 Memory Controller,
and setup related platform device during system booting up, against
which CPC925 Memory Controller EDAC driver would be matched.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m32r: PTRACE_SINGLESTEP sets PT_DTRACE, it is never used except cleared
after do_execve().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
avr32, mn10300, parisc, s390, sh, xtensa:
They never set PT_DTRACE, but clear it after do_execve().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Chris Zankel <chris@zankel.net>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
h8300 defines PT_DTRACE for asm but never uses it.
DEFINE(PT_PTRACED, PT_PTRACED) seems to be unused too.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel_fpu_begin/end used preempt_disable/enable, so sleep should be
prevented between kernel_fpu_begin/end.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Because AES-NI instructions will touch XMM state, corresponding code
must be enclosed within kernel_fpu_begin/end, which used
preempt_disable/enable. So sleep should be prevented between
kernel_fpu_begin/end.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Original implementation of aesni_cbc_dec do not save IV if input
length % 4 == 0. This will make decryption of next block failed.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
GCC 4.5.0 complains about the declaration of variables
__kernel_sigreturn and __kernel_rt_sigreturn because they have type
void. Correctly declare these symbols as functions to fix the
following error,
arch/sh/kernel/signal_32.c: In function 'setup_frame':
arch/sh/kernel/signal_32.c:368:14: error: taking address of expression of type 'void'
arch/sh/kernel/signal_32.c: In function 'setup_rt_frame':
arch/sh/kernel/signal_32.c:452:14: error: taking address of expression of type 'void'
make[1]: *** [arch/sh/kernel/signal_32.o] Error 1
make: *** [arch/sh/kernel] Error 2
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the performance monitor hardware on the
MPC7450 family of processors (7450, 7451, 7455, 7447/7457, 7447A,
7448), used in the later Apple G4 powermacs/powerbooks and other
machines. These machines have 6 hardware counters with a unique
set of events which can be counted on each counter, with some
events being available on multiple counters.
Raw event codes for these processors are (PMC << 8) + PMCSEL.
If PMC is non-zero then the event is that selected by the given
PMCSEL value for that PMC (hardware counter). If PMC is zero
then the event selected is one of the low-numbered ones that are
common to several PMCs. In this case PMCSEL must be <= 22 and
the event is what that PMCSEL value would select on PMC1 (but
it may be placed any other PMC that has the same event for that
PMCSEL value).
For events that count cycles or occurrences that exceed a threshold,
the threshold requested can be specified in the 0x3f000 bits of the
raw event codes. If the event uses the threshold multiplier bit
and that bit should be set, that is indicated with the 0x40000 bit
of the raw event code.
This fills in some of the generic cache events. Unfortunately there
are quite a few blank spaces in the table, partly because these
processors tend to count cache hits rather than cache accesses.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55631.802122.696927@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This abstracts a few things in arch/powerpc/kernel/perf_counter.c
that are specific to 64-bit kernels, and provides definitions for
32-bit kernels. In particular,
* Only 64-bit has MMCRA and the bits in it that give information
about a PMU interrupt (sampled PR, HV, slot number etc.)
* Only 64-bit has the lppaca and the lppaca->pmcregs_in_use field
* Use of SDAR is confined to 64-bit for now
* Only 64-bit has soft/lazy interrupt disable and therefore
pseudo-NMIs (interrupts that occur while interrupts are soft-disabled)
* Only 64-bit has PMC7 and PMC8
* Only 64-bit has the MSR_HV bit.
This also fixes the types used in a couple of places, where we were
using long types for things that need to be 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55590.634126.876084@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At present, the powerpc generic (processor-independent) perf_counter
code has list of processor back-end modules, and at initialization,
it looks at the PVR (processor version register) and has a switch
statement to select a suitable processor-specific back-end.
This is going to become inconvenient as we add more processor-specific
back-ends, so this inverts the order: now each back-end checks whether
it applies to the current processor, and registers itself if so.
Furthermore, instead of looking at the PVR, back-ends now check the
cur_cpu_spec->oprofile_cpu_type string and match on that.
Lastly, each back-end now specifies a name for itself so the core can
print a nice message when a back-end registers itself.
This doesn't provide any support for unregistering back-ends, but that
wouldn't be hard to do and would allow back-ends to be modules.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55529.762227.518531@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This changes the powerpc perf_counter back-end to use unsigned long
types for hardware register values and for the value/mask pairs used
in checking whether a given set of events fit within the hardware
constraints. This is in preparation for adding support for the PMU
on some 32-bit powerpc processors. On 32-bit processors the hardware
registers are only 32 bits wide, and the PMU structure is generally
simpler, so 32 bits should be ample for expressing the hardware
constraints. On 64-bit processors, unsigned long is 64 bits wide,
so using unsigned long vs. u64 (unsigned long long) makes no actual
difference.
This makes some other very minor changes: adjusting whitespace to line
things up in initialized structures, and simplifying some code in
hw_perf_disable().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55473.26174.331511@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This enables the perf_counter subsystem on 32-bit powerpc. Since we
don't have any support for hardware counters on 32-bit powerpc yet,
only software counters can be used.
Besides selecting HAVE_PERF_COUNTERS for 32-bit powerpc as well as
64-bit, the main thing this does is add an implementation of
set_perf_counter_pending(). This needs to arrange for
perf_counter_do_pending() to be called when interrupts are enabled.
Rather than add code to local_irq_restore as 64-bit does, the 32-bit
set_perf_counter_pending() generates an interrupt by setting the
decrementer to 1 so that a decrementer interrupt will become pending
in 1 or 2 timebase ticks (if a decrementer interrupt isn't already
pending). When interrupts are enabled, timer_interrupt() will be
called, and some new code in there calls perf_counter_do_pending().
We use a per-cpu array of flags to indicate whether we need to call
perf_counter_do_pending() or not.
This introduces a couple of new Kconfig symbols: PPC_HAVE_PMU_SUPPORT,
which is selected by processor families for which we have hardware PMU
support (currently only PPC64), and PPC_PERF_CTRS, which enables the
powerpc-specific perf_counter back-end.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55404.103840.393470@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need a cleared cpu_mask to record if mce is initialized, especially
when MAXSMP is used.
used zalloc_... instead
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The sysfs attribute cmci_disabled was accidentall turned into a
duplicate of ignore_ce, breaking all other attributes.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
arch/sh has a couple of stray markers without any users introduced
in commit 3d58695edb. Remove them in
preparation of removing the markers in favour of the TRACE_EVENT
macro (and also because we don't keep dead code around).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
asm/desc.h is included in three assembly files, but the only macro
it defines, GET_DESC_BASE, is never used. This patch removes the
includes, removes the macro GET_DESC_BASE and the ASSEMBLY guard
from asm/desc.h.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The espfix code triggers if we have a protected mode userspace
application with a 16-bit stack. On returning to userspace, with iret,
the CPU doesn't restore the high word of the stack pointer. This is an
"official" bug, and the work-around used in the kernel is to temporarily
switch to a 32-bit stack segment/pointer pair where the high word of the
pointer is equal to the high word of the userspace stackpointer.
The current implementation uses THREAD_SIZE to determine the cut-off,
but there is no good reason not to use the more natural 64kb... However,
implementing this by simply substituting THREAD_SIZE with 65536 in
patch_espfix_desc crashed the test application. patch_espfix_desc tries
to do what is described above, but gets it subtly wrong if the userspace
stack pointer is just below a multiple of THREAD_SIZE: an overflow
occurs to bit 13... With a bit of luck, when the kernelspace
stackpointer is just below a 64kb-boundary, the overflow then ripples
trough to bit 16 and userspace will see its stack pointer changed by
65536.
This patch moves all espfix code into entry_32.S. Selecting a 16-bit
cut-off simplifies the code. The game with changing the limit dynamically
is removed too. It complicates matters and I see no value in it. Changing
only the top 16-bit word of ESP is one instruction and it also implies
that only two bytes of the ESPFIX GDT entry need to be changed and this
can be implemented in just a handful simple to understand instructions.
As a side effect, the operation to compute the original ESP from the
ESPFIX ESP and the GDT entry simplifies a bit too, and the remaining
three instructions have been expanded inline in entry_32.S.
impact: can now reliably run userspace with ESP=xxxxfffc on 16-bit
stack segment
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Returning to a task with a 16-bit stack requires special care: the iret
instruction does not restore the high word of esp in that case. The
espfix code fixes this, but currently is not invoked on NMIs. This means
that a running task gets the upper word of esp clobbered due intervening
NMIs. To reproduce, compile and run the following program with the nmi
watchdog enabled (nmi_watchdog=2 on the command line). Using gdb you can
see that the high bits of esp contain garbage, while the low bits are
still correct.
This patch puts the espfix code back into the NMI code path.
The patch is slightly complicated due to the irqtrace infrastructure not
being NMI-safe. The NMI return path cannot call TRACE_IRQS_IRET.
Otherwise, the tail of the normal iret-code is correct for the nmi code
path too. To be able to share this code-path, the TRACE_IRQS_IRET was
move up a bit. The espfix code exists after the TRACE_IRQS_IRET, but
this code explicitly disables interrupts. This short interrupts-off
section is now not traced anymore. The return-to-kernel path now always
includes the preliminary test to decide if the espfix code should be
called. This is never the case, but doing it this way keeps the patch as
simple as possible and the few extra instructions should not affect
timing in any significant way.
#define _GNU_SOURCE
#include <stdio.h>
#include <sys/types.h>
#include <sys/mman.h>
#include <unistd.h>
#include <sys/syscall.h>
#include <asm/ldt.h>
int modify_ldt(int func, void *ptr, unsigned long bytecount)
{
return syscall(SYS_modify_ldt, func, ptr, bytecount);
}
/* this is assumed to be usable */
#define SEGBASEADDR 0x10000
#define SEGLIMIT 0x20000
/* 16-bit segment */
struct user_desc desc = {
.entry_number = 0,
.base_addr = SEGBASEADDR,
.limit = SEGLIMIT,
.seg_32bit = 0,
.contents = 0, /* ??? */
.read_exec_only = 0,
.limit_in_pages = 0,
.seg_not_present = 0,
.useable = 1
};
int main(void)
{
setvbuf(stdout, NULL, _IONBF, 0);
/* map a 64 kb segment */
char *pointer = mmap((void *)SEGBASEADDR, SEGLIMIT+1,
PROT_EXEC|PROT_READ|PROT_WRITE,
MAP_SHARED|MAP_ANONYMOUS, -1, 0);
if (pointer == NULL) {
printf("could not map space\n");
return 0;
}
/* write ldt, new mode */
int err = modify_ldt(0x11, &desc, sizeof(desc));
if (err) {
printf("error modifying ldt: %i\n", err);
return 0;
}
for (int i=0; i<1000; i++) {
asm volatile (
"pusha\n\t"
"mov %ss, %eax\n\t" /* preserve ss:esp */
"mov %esp, %ebp\n\t"
"push $7\n\t" /* index 0, ldt, user mode */
"push $65536-4096\n\t" /* esp */
"lss (%esp), %esp\n\t" /* switch to new stack */
"push %eax\n\t" /* save old ss:esp on new stack */
"push %ebp\n\t"
"add $17*65536, %esp\n\t" /* set high bits */
"mov %esp, %edx\n\t"
"mov $10000000, %ecx\n\t" /* wait... */
"1: loop 1b\n\t" /* ... a bit */
"cmp %esp, %edx\n\t"
"je 1f\n\t"
"ud2\n\t" /* esp changed inexplicably! */
"1:\n\t"
"sub $17*65536, %esp\n\t" /* restore high bits */
"lss (%esp), %esp\n\t" /* restore old ss:esp */
"popa\n\t");
printf("\rx%ix", i);
}
return 0;
}
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
ia64 was assigning resources to root busses after allocations had
been made for child busses. Calling pcibios_setup_root_windows() from
pcibios_fixup_bus() solves this problem by assigning the resources to
the root bus before child busses are scanned.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function was only used by pci_claim_resource(), and the last commit
deleted that use.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Convert ia64 to use int-ll64.h
[IA64] Fix build error in paravirt_patchlist.c
[IA64] ia64 does not need umount2() syscall
[IA64] hook up new rt_tgsigqueueinfo syscall
[IA64] msi_ia64.c dmar_msi_type should be static
[IA64] remove obsolete hw_interrupt_type
[IA64] remove obsolete irq_desc_t typedef
[IA64] remove obsolete no_irq_type
[IA64] unexport fpswa.h
Commit 9e350de37a ("perf_counter: Accurate period data")
missed a spot, which caused all Intel-PMU samples to have a
period of 0.
This broke auto-freq sampling.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
<linux/types.h> is only required for __KERNEL__ as whole file is covered with it
Also fixed some spacing issues for usr/include/asm-x86/msr.h
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: "H. Peter Anvin" <hpa@kernel.org>
LKML-Reference: <1245228070.2662.1.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] cpumask: new cpumask operators for arch/x86/kernel/cpu/cpufreq/powernow-k8.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in powernow-k8.c
[CPUFREQ] cpumask: avoid cpumask games in arch/x86/kernel/cpu/cpufreq/speedstep-centrino.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c
[CPUFREQ] powernow-k8: get drv data for correct CPU
[CPUFREQ] powernow-k8: read P-state from HW
[CPUFREQ] reduce scope of ACPI_PSS_BIOS_BUG_MSG[]
[CPUFREQ] Clean up convoluted code in arch/x86/kernel/tsc.c:time_cpufreq_notifier()
[CPUFREQ] minor correction to cpu-freq documentation
[CPUFREQ] powernow-k8.c: mess cleanup
[CPUFREQ] Only set sampling_rate_max deprecated, sampling_rate_min is useful
[CPUFREQ] powernow-k8: Set transition latency to 1 if ACPI tables export 0
[CPUFREQ] ondemand: Uncouple minimal sampling rate from HZ in NO_HZ case
It is generally agreed that it would be beneficial for u64 to be an
unsigned long long on all architectures. ia64 (in common with several
other 64-bit architectures) currently uses unsigned long. Migrating
piecemeal is too painful; this giant patch fixes all compilation warnings
and errors that come as a result of switching to use int-ll64.h.
Note that userspace will still see __u64 defined as unsigned long. This
is important as it affects C++ name mangling.
[Updated by Tony Luck to change efi.h:efi_freemem_callback_t to use
u64 for start/end rather than unsigned long]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Expand Intel NMI perfctr1 workaround to include a Core2 processor stepping
(cpuid family-6, model-f, stepping-4). Resolves a situation where the NMI
would not enable on these processors.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: prarit@redhat.com
Cc: suresh.b.siddha@intel.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew cleaned up some #include tangles in:
commit 0d9c25dde8
headers: move module_bug_finalize()/module_bug_cleanup() definitions into module.h
which resulted in this build error for ia64:
CC arch/ia64/kernel/paravirt_patchlist.o
arch/ia64/kernel/paravirt_patchlist.c:43: error: expected '=', ',', ';', 'asm' or '__attribute__' before '__initdata'
arch/ia64/kernel/paravirt_patchlist.c:54: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'paravirt_get_gate_patchlist'
arch/ia64/kernel/paravirt_patchlist.c:76: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'paravirt_get_gate_section'
make[1]: *** [arch/ia64/kernel/paravirt_patchlist.o] Error 1
The problem was that paravirt_patchlist.c was relying on some of the
nested includes (specifically that linux/bug.h included linux/module.h
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
mce_intel.c uses apic_write() and lapic_get_maxlvt(), and so it needs
<asm/apic.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
This compiler warning:
arch/x86/kernel/apic/io_apic.c: In function ‘ioapic_write_entry’:
arch/x86/kernel/apic/io_apic.c:466: warning: ‘eu’ is used uninitialized in this function
arch/x86/kernel/apic/io_apic.c:465: note: ‘eu’ was declared here
Is bogus as 'eu' is always initialized. But annotate it away by
initializing the variable, to make it easier for people to notice
real warnings. A compiler that sees through this logic will
optimize away the initialization.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
LKML-Reference: <1245248720.3312.27.camel@myhost>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If APIC was disabled (for some reason) and as result
it's not even mapped we should not try to enable thermal
interrupts at all.
Reported-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Tested-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090615182633.GA7606@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For freqency dependent TSCs we only scale the cycles, we do not account
for the discrepancy in absolute value.
Our current formula is: time = cycles * mult
(where mult is a function of the cpu-speed on variable tsc machines)
Suppose our current cycle count is 10, and we have a multiplier of 5,
then our time value would end up being 50.
Now cpufreq comes along and changes the multiplier to say 3 or 7,
which would result in our time being resp. 30 or 70.
That means that we can observe random jumps in the time value due to
frequency changes in both fwd and bwd direction.
So what this patch does is change the formula to:
time = cycles * frequency + offset
And we calculate offset so that time_before == time_after, thereby
ridding us of these jumps in time.
[ Impact: fix/reduce sched_clock() jumps across frequency changing events ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Chucked-on-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[Ralf: SMP support requires CPU hotplugging which MIPS currently doesn't
support. As implemented in this patch cache and tlb flushing will also be
invoked with interrupts disabled so smp_call_function() will blow up in
charming ways. So limit to !SMP.]
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Yan Hua <yanh@lemote.com>
Reviewed-by: Arnaud Patard <apatard@mandriva.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Hu Hongbing <huhb@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We had an ugly #ifdef for Cavium Octeon hwrena bits in traps.c, remove
it to mach-cavium-octeon/cpu-feature-overrides.h
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs have implementation dependent rdhwr registers. Allow them
to be enabled on a per CPU basis.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add new kconfig variables SYS_SUPPORTS_HUGETLBFS and
CPU_SUPPORTS_HUGEPAGES. They are enabled for systems that are known
to support huge pages.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The TLB handlers need to check for huge pages and give them special
handling. Huge pages consist of two contiguous sub-pages of physical
memory.
* Loading entrylo0 and entrylo1 need to be handled specially.
* The page mask must be set for huge pages and then restored after
writing the TLB entries.
* The PTE for huge pages resides in the PMD, we halt traversal of the
tables there.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The l parameter to iPTE_LW() is unused. Remove it and from some of its
callers as well.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The octeon-ethernet driver needs to check for additional chip specific
features, we add them to the octeon_has_feature() framework.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The bootloader now uses additional board type constants. The
octeon-ethernet driver needs some of the new values.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various Octeon ethernet drivers use these new functions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few open-coded GPIO register accesses with gpio calls.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls to
the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls
to the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current in-kernel Alchemy GPIO support is far too inflexible for
all my use cases. To address this, the following changes are made:
* create generic functions which deal with manipulating the on-chip
GPIO1/2 blocks. Such functions are universally useful.
* Macros for GPIO2 shared interrupt management and block control.
* support for both built-in CONFIG_GPIOLIB and fast, inlined GPIO macros.
If CONFIG_GPIOLIB is not enabled, provide linux gpio framework
compatibility by directly inlining the GPIO1/2 functions. GPIO access
is limited to on-chip ones and they can be accessed as documented in
the datasheets (GPIO0-31 and 200-215).
If CONFIG_GPIOLIB is selected, two (2) gpio_chip-s, one for GPIO1 and
one for GPIO2, are registered. GPIOs can still be accessed by using
the numberspace established in the databooks.
However this is not yet flexible enough for my uses: My Alchemy
systems have a documented "external" gpio interface (fixed, different
numberspace) and can support a variety of baseboards, some of which
are equipped with I2C gpio expanders. I want to be able to provide
the default 16 GPIOs of the CPU board numbered as 0..15 and also
support gpio expanders, if present, starting as gpio16.
To achieve this, a new Kconfig symbol for Alchemy is introduced,
CONFIG_ALCHEMY_GPIO_INDIRECT, which boards can enable to signal
that they don't want the Alchemy numberspace exposed to the outside
world, but instead want to provide their own. Boards are now respon-
sible for providing the linux gpio interface glue code (either in a
custom gpio.h header (in board include directory) or with gpio_chips).
To make the board-specific inlined gpio functions work, the MIPS
Makefile must be changed so that the mach-au1x00/gpio.h header is
included _after_ the board headers, by moving the inclusion of
the mach-au1x00/ to the end of the header list.
See arch/mips/include/asm/mach-au1x00/gpio.h for more info.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
gpio_direction_output should also set an output value according to the API.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Rewrite to use <asm-generic/ioctl.h>. Cuts down the file from 40 to
16 lines.
o Delete _IOC_VOID, _IOC_OUT, _IOC_IN and _IOC_INOUT. They were added
for 2.1.14 but I was not able to find any user - not even historical
ones.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a sysdev to access SRAM in TXx9 SoCs via sysfs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CFE is the only supported and used bootloader on the SiByte boards,
the standalone kernel support has been never used outside Broadcom.
Remove it and make the kernel use CFE by default.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the SiByte simulation Kconfig option, which only modified
a printk.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon has no execution hazards, so we can remove them and save an
instruction per TLB handler invocation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add platform support for ACLC of TXx9 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here we add the register definitions for the processor blocks used by
the following PCI support patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use container structure for clocksource, clock_event_device and hold a
pointer to txx9_tmr_reg in it.
This saves a few instructions in clocksource and clock_event handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A wrong resolution of a merge conflict made the recently deleted wrong
error check in sb1250_set_affinity. Send the zombie back to the empire
of the undead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds initial support for the PCI-Express module in the SH7786,
particularly as it relates to the urquell platform. Presently it is
only supported in root complex mode, with endpoint mode still requiring
more debugging. 29/32-bit mode and lane configurations are selectable via
board mode pins, and are otherwise fixed.
Only 4x and 1x PCI channels are presently handled, the PCI bridge still
requires additional debugging and stabilization in hardware.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables support for the generic software-based perf counters.
Hardware counter support could be added in the future, but the lack
of a performance counter IRQ makes this rather dubious.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch refactors clock.c by replacing printk calls with
pr_info/pr_cont, and uses '=' in output to connect key/value pairs
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Unify i2c camera device platform data to point to struct soc_camera_link
for a smooth transition to soc-camera as a platform driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
and remove redundant parameter for r8a66597-hcd.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the shared clock cpg code from bootmem to slab.
Without this patch the current bootmem code triggers
WARN_ON() because the slab is available.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>