Some RS690 chipsets seem to end up with floating connectors, either
a DVI connector isn't actually populated, or an add-in HDMI card
is available but not installed. In this case we seem to get a NULL byte
response for each byte of the i2c transaction, so we detect this
case and if we see it we don't do anymore DDC transactions on this
connector.
I've tested this on my RS690 without the HDMI card installed and
it seems to work fine.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
* 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/atom: fix PHY init
drm/radeon/kms: add missing Evergreen texture formats to the CS parser
drm/radeon/kms: viewport height has to be even
drm/radeon/kms: remove duplicate reg from r600 safe regs
drm/radeon/kms: add support for Llano Fusion APUs
drm/radeon/kms: add llano pci ids
drm/radeon/kms: fill in asic struct for llano
drm/radeon/kms: add family ids for llano APUs
drm/radeon: fix oops in ttm reserve when pageflipping (v2)
drm/radeon/kms: clean up the radeon kms Kconfig
drm/radeon/kms: fix thermal sensor reading on juniper
drm/radeon/kms: add missing case for cayman thermal sensor
drm/radeon/kms: add blit support for cayman (v2)
drm/radeon/kms/blit: workaround some hw issues on evergreen+
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
We need to hold the dev->mode_config.mutex whilst detecting the output
status. But we also need to drop it for the call into
drm_fb_helper_single_fb_probe(), which indirectly acquires the lock when
attaching the fbcon.
Failure to do so exposes a race with normal output probing. Detected by
adding some warnings that the mutex is held to the backend detect routines:
[ 17.772456] WARNING: at drivers/gpu/drm/i915/intel_crt.c:471 intel_crt_detect+0x3e/0x373 [i915]()
[ 17.772458] Hardware name: Latitude E6400
[ 17.772460] Modules linked in: ....
[ 17.772582] Pid: 11, comm: kworker/0:1 Tainted: G W 2.6.38.4-custom.2 #8
[ 17.772584] Call Trace:
[ 17.772591] [<ffffffff81046af5>] ? warn_slowpath_common+0x78/0x8c
[ 17.772603] [<ffffffffa03f3e5c>] ? intel_crt_detect+0x3e/0x373 [i915]
[ 17.772612] [<ffffffffa0355d49>] ? drm_helper_probe_single_connector_modes+0xbf/0x2af [drm_kms_helper]
[ 17.772619] [<ffffffffa03534d5>] ? drm_fb_helper_probe_connector_modes+0x39/0x4d [drm_kms_helper]
[ 17.772625] [<ffffffffa0354760>] ? drm_fb_helper_hotplug_event+0xa5/0xc3 [drm_kms_helper]
[ 17.772633] [<ffffffffa035577f>] ? output_poll_execute+0x146/0x17c [drm_kms_helper]
[ 17.772638] [<ffffffff81193c01>] ? cfq_init_queue+0x247/0x345
[ 17.772644] [<ffffffffa0355639>] ? output_poll_execute+0x0/0x17c [drm_kms_helper]
[ 17.772648] [<ffffffff8105b540>] ? process_one_work+0x193/0x28e
[ 17.772652] [<ffffffff8105c6bc>] ? worker_thread+0xef/0x172
[ 17.772655] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772658] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772663] [<ffffffff8105f767>] ? kthread+0x7a/0x82
[ 17.772668] [<ffffffff8100a724>] ? kernel_thread_helper+0x4/0x10
[ 17.772671] [<ffffffff8105f6ed>] ? kthread+0x0/0x82
[ 17.772674] [<ffffffff8100a720>] ? kernel_thread_helper+0x0/0x10
Reported-by: Frederik Himpe <fhimpe@telenet.be>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36394
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'keithp/drm-intel-next' of /ssd/git/drm-next: (301 commits)
drm/i915: split PCH clock gating init
drm/i915: add Ivybridge clock gating init function
drm/i915: Update the location of the ringbuffers' HWS_PGA registers for IVB.
drm/i915: Add support for fence registers on Ivybridge.
drm/i915: Use existing function instead of open-coding fence reg clear.
drm/i915: split clock gating init into per-chipset functions
drm/i915: set IBX pch type explicitly
drm/i915: add Ivy Bridge PCI IDs and driver feature structs
drm/i915: add PantherPoint PCH ID
agp/intel: add Ivy Bridge support
drm/i915: ring support for Ivy Bridge
drm/i915: page flip support for Ivy Bridge
drm/i915: interrupt & vblank support for Ivy Bridge
drm/i915: treat Ivy Bridge watermarks like Sandy Bridge
drm/i915: manual FDI training for Ivy Bridge
drm/i915: add swizzle/tiling support for Ivy Bridge
drm/i915: Ivy Bridge has split display and pipe control
drm/i915: add IS_IVYBRIDGE macro for checks
drm/i915: add IS_GEN7 macro to cover Ivy Bridge and later
drm/i915: split enable/disable vblank code into chipset specific functions
...
The looping helper didn't do anything due to a superficial
semicolon. Furthermore one of the two dump functions suffered
from copy&paste fail.
While staring at the code I've also noticed that the replace
helper (currently unused) is a bit broken.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Out of the entire GART/VM subsystem, the hw designers changed
the location of 3 regs.
v2: airlied: add parameter for userspace to work from.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the absence of configuration data for providing the fixed mode for
a panel, I would like to be able to pass such modes along a separate
module paramenter. To do so, I then need to parse a modeline from a
string, which drm is already capable of. Export that capability to the
drivers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add __attribute__((format (printf, 4, 5))) to drm_ut_debug_printk
and fix fallout.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reduce drm text size ~1% by using drm_err and
printf extension %pV to emit error messages.
Remove unused macro DRM_MEM_ERROR.
$ size drivers/gpu/drm/built-in.o*
text data bss dec hex filename
361159 9663 256 371078 5a986 drivers/gpu/drm/built-in.o.new
365416 9663 256 375335 5ba27 drivers/gpu/drm/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to hold the dev->mode_config.mutex whilst detecting the output
status. But we also need to drop it for the call into
drm_fb_helper_single_fb_probe(), which indirectly acquires the lock when
attaching the fbcon.
Failure to do so exposes a race with normal output probing. Detected by
adding some warnings that the mutex is held to the backend detect routines:
[ 17.772456] WARNING: at drivers/gpu/drm/i915/intel_crt.c:471 intel_crt_detect+0x3e/0x373 [i915]()
[ 17.772458] Hardware name: Latitude E6400
[ 17.772460] Modules linked in: ....
[ 17.772582] Pid: 11, comm: kworker/0:1 Tainted: G W 2.6.38.4-custom.2 #8
[ 17.772584] Call Trace:
[ 17.772591] [<ffffffff81046af5>] ? warn_slowpath_common+0x78/0x8c
[ 17.772603] [<ffffffffa03f3e5c>] ? intel_crt_detect+0x3e/0x373 [i915]
[ 17.772612] [<ffffffffa0355d49>] ? drm_helper_probe_single_connector_modes+0xbf/0x2af [drm_kms_helper]
[ 17.772619] [<ffffffffa03534d5>] ? drm_fb_helper_probe_connector_modes+0x39/0x4d [drm_kms_helper]
[ 17.772625] [<ffffffffa0354760>] ? drm_fb_helper_hotplug_event+0xa5/0xc3 [drm_kms_helper]
[ 17.772633] [<ffffffffa035577f>] ? output_poll_execute+0x146/0x17c [drm_kms_helper]
[ 17.772638] [<ffffffff81193c01>] ? cfq_init_queue+0x247/0x345
[ 17.772644] [<ffffffffa0355639>] ? output_poll_execute+0x0/0x17c [drm_kms_helper]
[ 17.772648] [<ffffffff8105b540>] ? process_one_work+0x193/0x28e
[ 17.772652] [<ffffffff8105c6bc>] ? worker_thread+0xef/0x172
[ 17.772655] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772658] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772663] [<ffffffff8105f767>] ? kthread+0x7a/0x82
[ 17.772668] [<ffffffff8100a724>] ? kernel_thread_helper+0x4/0x10
[ 17.772671] [<ffffffff8105f6ed>] ? kthread+0x0/0x82
[ 17.772674] [<ffffffff8100a720>] ? kernel_thread_helper+0x0/0x10
Reported-by: Frederik Himpe <fhimpe@telenet.be>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36394
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EDID 1.4 digital displays report the color spaces they support in the
features block. Add support for grabbing this data and stuffing it into
the display_info struct for driver use.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EDID 1.4 digital monitors report the bit depth supported in the input
field. Add support for parsing this out and storing the info in the
display_info structure for use by drivers.
[airlied: tweaked to fix inter-patch dependency]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Nouveau needs access to this structure to build an ELD block for use
by the HDA audio codec.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes the interface a bit cleaner by leaving a single gap in the
vblank bit space instead of creating two gaps.
Suggestions from Michel on mailing list/irc.
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Below is a patch against drm-next branch of 2.6.38-rc8+ kernel that adds
the capability to wait on vblank events for CRTCs that are greater than 1
and thus cannot be represented with primary/secondary flags in the legacy
interface. It was discussed on the dri-devel list in these two threads:
http://lists.freedesktop.org/archives/dri-devel/2011-March/009009.htmlhttp://lists.freedesktop.org/archives/dri-devel/2011-March/009025.html
This patch extends the interface to drm_wait_vblank ioctl so that crtc>1
can be represented. It also adds a new capability to drm_getcap ioctl so
that the user space can check whether the new interface to drm_wait_vblank
is supported (and fall back to the legacy interface if not)
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Mario Kleiner <mario.kleiner at tuebingen.mpg.de>
Acked-by: Mario Kleiner <mario.kleiner at tuebingen.mpg.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
We're coming to see a need to have a set of generic capability checks in
the core DRM, in addition to the driver-specific ioctls that already
exist.
This patch defines an ioctl to do as such, but does not yet define any
capabilities.
[airlied: drop the driver callback for now.]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace has a legitimate requirement to use a delta that points to
outside of the target bo, and so we need to enable this. (As this is an
abi break, albeit a relaxation of the current restrictions, mark the change
with a new flag.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 5a893fc28f.
This causes a use after free in the ttm free alloc pages path,
when it tries to get the be after the be has been destroyed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'stable/ttm.pci-api.v5' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
ttm: Include the 'struct dev' when using the DMA API.
nouveau/ttm/PCIe: Use dma_addr if TTM has set it.
radeon/ttm/PCIe: Use dma_addr if TTM has set it.
ttm: Expand (*populate) to support an array of DMA addresses.
ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set.
ttm: Introduce a placeholder for DMA (bus) addresses.
... and fixup some methods to accept the constant argument.
Now that constant module arrays are loaded into read-only memory, using
const appropriately has some benefits beyond warning the programmer
about likely mistakes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the switch to implicit free space accounting one pointer
got unused when scanning. Use it to create a single-linked list
to ensure correct unwinding of the scan state.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old api has a two-step process: First search for a suitable
free hole, then allocate from that specific hole. No user used
this to do anything clever. So drop it for the embeddable variant
of the drm_mm api (the old one retains this ability, for the time
being).
With struct drm_mm_node embedded, we cannot track allocations
anymore by checking for a NULL pointer. So keep track of this
and add a small helper drm_mm_node_allocated.
Also add a function to move allocations between different struct
drm_mm_node.
v2: Implement suggestions by Chris Wilson.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The idea is to track free holes implicitly by marking the allocation
immediatly preceeding a hole.
To avoid an ugly corner case add a dummy head_node to struct drm_mm
to track the hole that spans to complete allocation area when the
memory manager is empty.
To guarantee that there's always a preceeding/following node (that might
be marked as hole_follows == 1), move the mm->node_list list_head to the
head_node.
The main allocator and fair-lru scan code actually becomes simpler.
Only the debug code slightly suffers because free areas are no longer
explicit.
Also add drm_mm_for_each_node (which will be much more useful when
struct drm_mm_node is embeddable).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Nouveau was checking drm_mm internals on teardown to see whether the
memory manager was initialized. Hide these internals in a small
inline helper function.
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes the accounting when using 'debug_dma_dump_mappings()'
and CONFIG_DMA_API_DEBUG=y be assigned to the correct device
instead of 'fallback'.
No functional change - just cosmetic.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This adds an initial framework to plug USB graphics devices
into the drm/kms subsystem.
I've started writing a displaylink driver using this interface.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This abstracts the pci/platform interface out a step further,
we can go further but this is far enough for now to allow USB
to be plugged in.
The drivers now just call the init code directly for their
device type.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is just an idea that might or might not be a good idea,
it basically adds two ioctls to create a dumb and map a dumb buffer
suitable for scanout. The handle can be passed to the KMS ioctls to create
a framebuffer.
It looks to me like it would be useful in the following cases:
a) in development drivers - we can always provide a shadowfb fallback.
b) libkms users - we can clean up libkms a lot and avoid linking
to libdrm_*.
c) plymouth via libkms is a lot easier.
Userspace bits would be just calls + mmaps. We could probably
mark these handles somehow as not being suitable for acceleartion
so as top stop people who are dumber than dumb.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This driver is one of the last users of the big kernel
lock, which is going away. All the hardware supported
by this driver also works with the newer i915 driver,
and recent X.org releases only work with that driver
anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher
Dave Airlie
Linus Torvalds
Chris Wilson
Dave Airlie
Daniel Vetter
Joe Perches
Jesse Barnes
Jan Engelhardt
Ben Skeggs
Lucas De Marchi
Ilija Hadzic
Konrad Rzeszutek Wilk
Dave Airlie
Arnd Bergmann